Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

usb: ehci-mx6: add support for otg port

Browse Source 
Previously, only host1 was supported using an index of 0.
Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3.
Since OTG requires usbmode to be set after reset, I added
CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and
mx6qsabreauto.h.

I also added a weak function board_ehci_power to handle
turning power on/off for otg.

Type is type of device connected (USB stick vs Host.)
Init is type of device desired.
Only power up port if type == init == USB_INIT_HOST.
Only return error if type != init.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
master
Troy Kisky 12 years ago committed by Marek Vasut
parent 8287314888
commit d1a5286099
3 changed files with 95 additions and 42 deletions
  1. 131
      drivers/usb/host/ehci-mx6.c
  2. 3
      include/configs/mx6qsabreauto.h
  3. 3
      include/configs/nitrogen6x.h

131
drivers/usb/host/ehci-mx6.c
Unescape View File

@ -35,6 +35,7 @@
#define USBPHY_CTRL_CLKGATE 0x40000000
#define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
#define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
#define USBPHY_CTRL_OTG_ID 0x08000000
#define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000
#define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000
@ -49,52 +50,84 @@
#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection */
/* USBCMD */
#define UH1_USBCMD_OFFSET 0x140
#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
#define UCMD_RESET (1 << 1) /* controller reset */
static void usbh1_internal_phy_clock_gate(int on)
static const unsigned phy_bases[] = {
USB_PHY0_BASE_ADDR,
USB_PHY1_BASE_ADDR,
};
static void usb_internal_phy_clock_gate(int index, int on)
{
void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
void __iomem *phy_reg;
if (index >= ARRAY_SIZE(phy_bases))
return;
phy_reg = (void __iomem *)phy_bases[index];
phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
__raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
}
static void usbh1_power_config(void)
static void usb_power_config(int index)
{
struct anatop_regs __iomem *anatop =
(struct anatop_regs __iomem *)ANATOP_BASE_ADDR;
void __iomem *chrg_detect;
void __iomem *pll_480_ctrl_clr;
void __iomem *pll_480_ctrl_set;
switch (index) {
case 0:
chrg_detect = &anatop->usb1_chrg_detect;
pll_480_ctrl_clr = &anatop->usb1_pll_480_ctrl_clr;
pll_480_ctrl_set = &anatop->usb1_pll_480_ctrl_set;
break;
case 1:
chrg_detect = &anatop->usb2_chrg_detect;
pll_480_ctrl_clr = &anatop->usb2_pll_480_ctrl_clr;
pll_480_ctrl_set = &anatop->usb2_pll_480_ctrl_set;
break;
default:
return;
}
/*
* Some phy and power's special controls for host1
* Some phy and power's special controls
* 1. The external charger detector needs to be disabled
* or the signal at DP will be poor
* 2. The PLL's power and output to usb for host 1
* 2. The PLL's power and output to usb
* is totally controlled by IC, so the Software only needs
* to enable them at initializtion.
*/
__raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
&anatop->usb2_chrg_detect);
chrg_detect);
__raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
&anatop->usb2_pll_480_ctrl_clr);
pll_480_ctrl_clr);
__raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
ANADIG_USB2_PLL_480_CTRL_POWER |
ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
&anatop->usb2_pll_480_ctrl_set);
pll_480_ctrl_set);
}
static int usbh1_phy_enable(void)
/* Return 0 : host node, <>0 : device mode */
static int usb_phy_enable(int index, struct usb_ehci *ehci)
{
void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
void __iomem *phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
void __iomem *usb_cmd = (void __iomem *)(USBOH3_USB_BASE_ADDR +
USB_H1REGS_OFFSET +
UH1_USBCMD_OFFSET);
void __iomem *phy_reg;
void __iomem *phy_ctrl;
void __iomem *usb_cmd;
u32 val;
if (index >= ARRAY_SIZE(phy_bases))
return 0;
phy_reg = (void __iomem *)phy_bases[index];
phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
usb_cmd = (void __iomem *)&ehci->usbcmd;
/* Stop then Reset */
val = __raw_readl(usb_cmd);
val &= ~UCMD_RUN_STOP;
@ -123,31 +156,41 @@ static int usbh1_phy_enable(void)
/* Power up the PHY */
__raw_writel(0, phy_reg + USBPHY_PWD);
/* enable FS/LS device */
val = __raw_readl(phy_reg + USBPHY_CTRL);
val = __raw_readl(phy_ctrl);
val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
__raw_writel(val, phy_reg + USBPHY_CTRL);
__raw_writel(val, phy_ctrl);
return 0;
return val & USBPHY_CTRL_OTG_ID;
}
static void usbh1_oc_config(void)
/* Base address for this IP block is 0x02184800 */
struct usbnc_regs {
u32 ctrl[4]; /* otg/host1-3 */
u32 uh2_hsic_ctrl;
u32 uh3_hsic_ctrl;
u32 otg_phy_ctrl_0;
u32 uh1_phy_ctrl_0;
};
static void usb_oc_config(int index)
{
void __iomem *usb_base = (void __iomem *)USBOH3_USB_BASE_ADDR;
void __iomem *usbother_base = usb_base + USB_OTHERREGS_OFFSET;
struct usbnc_regs *usbnc = (struct usbnc_regs *)(USBOH3_USB_BASE_ADDR +
USB_OTHERREGS_OFFSET);
void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
u32 val;
val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
val = __raw_readl(ctrl);
#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
/* mx6qarm2 seems to required a different setting*/
val &= ~UCTRL_OVER_CUR_POL;
#else
val |= UCTRL_OVER_CUR_POL;
#endif
__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
__raw_writel(val, ctrl);
val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
val = __raw_readl(ctrl);
val |= UCTRL_OVER_CUR_DIS;
__raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
__raw_writel(val, ctrl);
}
int __weak board_ehci_hcd_init(int port)
@ -155,34 +198,42 @@ int __weak board_ehci_hcd_init(int port)
return 0;
}
int __weak board_ehci_power(int port, int on)
{
return 0;
}
int ehci_hcd_init(int index, enum usb_init_type init,
struct ehci_hccr **hccr, struct ehci_hcor **hcor)
{
struct usb_ehci *ehci;
enum usb_init_type type;
struct usb_ehci *ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
(0x200 * index));
if (index > 3)
return -EINVAL;
enable_usboh3_clk(1);
mdelay(1);
/* Do board specific initialization */
board_ehci_hcd_init(CONFIG_MXC_USB_PORT);
#if CONFIG_MXC_USB_PORT == 1
/* USB Host 1 */
usbh1_power_config();
usbh1_oc_config();
usbh1_internal_phy_clock_gate(1);
usbh1_phy_enable();
#else
#error "MXC USB port not yet supported"
#endif
board_ehci_hcd_init(index);
usb_power_config(index);
usb_oc_config(index);
usb_internal_phy_clock_gate(index, 1);
type = usb_phy_enable(index, ehci) ? USB_INIT_DEVICE : USB_INIT_HOST;
ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
(0x200 * CONFIG_MXC_USB_PORT));
*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
setbits_le32(&ehci->usbmode, CM_HOST);
if ((type == init) || (type == USB_INIT_DEVICE))
board_ehci_power(index, (type == USB_INIT_DEVICE) ? 0 : 1);
if (type != init)
return -ENODEV;
if (type == USB_INIT_DEVICE)
return 0;
setbits_le32(&ehci->usbmode, CM_HOST);
__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
setbits_le32(&ehci->portsc, USB_EN);

3
include/configs/mx6qsabreauto.h
Unescape View File

@ -23,7 +23,8 @@
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0

3
include/configs/nitrogen6x.h
Unescape View File

@ -125,7 +125,8 @@
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0

Write Preview
Loading…
Cancel
Save