diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index caf6690..00c793a 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -32,9 +32,170 @@ void ext_bus_cntlr_init(void); void configure_ppc440ep_pins(void); int is_nand_selected(void); -unsigned char cfg_simulate_spd_eeprom[128]; +#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) +/************************************************************************* + * + * Bamboo has one bank onboard sdram (plus DIMM) + * + * Fixed memory is composed of : + * MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266, + * 13 row add bits, 10 column add bits (but 12 row used only). + * ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266, + * 12 row add bits, 10 column add bits. + * Prepare a subset (only the used ones) of SPD data + * + * Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of + * the corresponding bank is divided by 2 due to number of Row addresses + * 12 in the ECC module + * + * Assumes: 64 MB, ECC, non-registered + * PLB @ 133 MHz + * + ************************************************************************/ +const unsigned char cfg_simulate_spd_eeprom[128] = { + 0x80, /* number of SPD bytes used: 128 */ + 0x08, /* total number bytes in SPD device = 256 */ + 0x07, /* DDR ram */ +#ifdef CONFIG_DDR_ECC + 0x0C, /* num Row Addr: 12 */ +#else + 0x0D, /* num Row Addr: 13 */ +#endif + 0x09, /* numColAddr: 9 */ + 0x01, /* numBanks: 1 */ + 0x20, /* Module data width: 32 bits */ + 0x00, /* Module data width continued: +0 */ + 0x04, /* 2.5 Volt */ + 0x75, /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */ +#ifdef CONFIG_DDR_ECC + 0x02, /* ECC ON : 02 OFF : 00 */ +#else + 0x00, /* ECC ON : 02 OFF : 00 */ +#endif + 0x82, /* refresh Rate Type: Normal (15.625us) + Self refresh */ + 0, + 0, + 0, + 0x01, /* wcsbc = 1 */ + 0, + 0, + 0x0C, /* casBit (2,2.5) */ + 0, + 0, + 0x00, /* not registered: 0 registered : 0x02*/ + 0, + 0xA0, /* SDRAM Cycle Time (cas latency 2) = 10 ns */ + 0, + 0x00, /* SDRAM Cycle Time (cas latency 1.5) = N.A */ + 0, + 0x50, /* tRpNs = 20 ns */ + 0, + 0x50, /* tRcdNs = 20 ns */ + 45, /* tRasNs */ +#ifdef CONFIG_DDR_ECC + 0x08, /* bankSizeID: 32MB */ +#else + 0x10, /* bankSizeID: 64MB */ +#endif + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0, + 0 +}; +#endif -gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; #if 0 { /* GPIO Alternate1 Alternate2 Alternate3 */ { @@ -291,73 +452,12 @@ int checkboard(void) return (0); } -#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) -/************************************************************************* - * - * init_spd_array -- Bamboo has one bank onboard sdram (plus DIMM) - * - * Fixed memory is composed of : - * MT46V16M16TG-75 from Micron (x 2), 256Mb, 16 M x16, DDR266, - * 13 row add bits, 10 column add bits (but 12 row used only). - * ECC device: MT46V16M8TG-75 from Micron (x 1), 128Mb, x8, DDR266, - * 12 row add bits, 10 column add bits. - * Prepare a subset (only the used ones) of SPD data - * - * Note : if the ECC is enabled (SDRAM_ECC_ENABLE) the size of - * the corresponding bank is divided by 2 due to number of Row addresses - * 12 in the ECC module - * - * Assumes: 64 MB, ECC, non-registered - * PLB @ 133 MHz - * - ************************************************************************/ -static void init_spd_array(void) -{ - cfg_simulate_spd_eeprom[8] = 0x04; /* 2.5 Volt */ - cfg_simulate_spd_eeprom[2] = 0x07; /* DDR ram */ - -#ifdef CONFIG_DDR_ECC - cfg_simulate_spd_eeprom[11] = 0x02; /* ECC ON : 02 OFF : 00 */ - cfg_simulate_spd_eeprom[31] = 0x08; /* bankSizeID: 32MB */ - cfg_simulate_spd_eeprom[3] = 0x0C; /* num Row Addr: 12 */ -#else - cfg_simulate_spd_eeprom[11] = 0x00; /* ECC ON : 02 OFF : 00 */ - cfg_simulate_spd_eeprom[31] = 0x10; /* bankSizeID: 64MB */ - cfg_simulate_spd_eeprom[3] = 0x0D; /* num Row Addr: 13 */ -#endif - - cfg_simulate_spd_eeprom[4] = 0x09; /* numColAddr: 9 */ - cfg_simulate_spd_eeprom[5] = 0x01; /* numBanks: 1 */ - cfg_simulate_spd_eeprom[0] = 0x80; /* number of SPD bytes used: 128 */ - cfg_simulate_spd_eeprom[1] = 0x08; /* total number bytes in SPD device = 256 */ - cfg_simulate_spd_eeprom[21] = 0x00; /* not registered: 0 registered : 0x02*/ - cfg_simulate_spd_eeprom[6] = 0x20; /* Module data width: 32 bits */ - cfg_simulate_spd_eeprom[7] = 0x00; /* Module data width continued: +0 */ - cfg_simulate_spd_eeprom[15] = 0x01; /* wcsbc = 1 */ - cfg_simulate_spd_eeprom[27] = 0x50; /* tRpNs = 20 ns */ - cfg_simulate_spd_eeprom[29] = 0x50; /* tRcdNs = 20 ns */ - - cfg_simulate_spd_eeprom[30] = 45; /* tRasNs */ - - cfg_simulate_spd_eeprom[18] = 0x0C; /* casBit (2,2.5) */ - - cfg_simulate_spd_eeprom[9] = 0x75; /* SDRAM Cycle Time (cas latency 2.5) = 7.5 ns */ - cfg_simulate_spd_eeprom[23] = 0xA0; /* SDRAM Cycle Time (cas latency 2) = 10 ns */ - cfg_simulate_spd_eeprom[25] = 0x00; /* SDRAM Cycle Time (cas latency 1.5) = N.A */ - cfg_simulate_spd_eeprom[12] = 0x82; /* refresh Rate Type: Normal (15.625us) + Self refresh */ -} -#endif long int initdram (int board_type) { #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) long dram_size; - /* - * First write simulated values in eeprom array for onboard bank 0 - */ - init_spd_array(); - dram_size = spd_sdram(); return dram_size; @@ -371,11 +471,12 @@ int testdram(void) { unsigned long *mem = (unsigned long *)0; const unsigned long kend = (1024 / sizeof(unsigned long)); - unsigned long k, n; + unsigned long k, n, *p32, ctr; + const unsigned long bend = CFG_MBYTES_SDRAM * 1024 * 1024; mtmsr(0); - for (k = 0; k < CFG_KBYTES_SDRAM; + for (k = 0; k < CFG_MBYTES_SDRAM*1024; ++k, mem += (1024 / sizeof(unsigned long))) { if ((k & 1023) == 0) { printf("%3d MB\r", k / 1024); @@ -399,6 +500,34 @@ int testdram(void) } } } + + /* + * Perform a sequence test to ensure that all + * memory locations are uniquely addressable + */ + ctr = 0; + p32 = 0; + while ((unsigned long)p32 != bend) { + if (0 == ((unsigned long)p32 & ((1<<20)-1))) + printf("Writing %3d MB\r", (unsigned long)p32 >> 20); + *p32++ = ctr++; + } + + ctr = 0; + p32 = 0; + while ((unsigned long)p32 != bend) { + if (0 == ((unsigned long)p32 & ((1<<20)-1))) + printf("Verifying %3d MB\r", (unsigned long)p32 >> 20); + + if (*p32 != ctr) { + printf("SDRAM test fails at: %08x\n", p32); + return 1; + } + + ctr++; + p32++; + } + printf("SDRAM test passes\n"); return 0; } @@ -1211,7 +1340,7 @@ void uart_selection_in_fpga(uart_config_nb_t uart_config) /*----------------------------------------------------------------------------+ | init_default_gpio +----------------------------------------------------------------------------*/ -void init_default_gpio(void) +void init_default_gpio(gpio_param_s (*gpio_tab)[GPIO_MAX]) { int i; @@ -1281,7 +1410,7 @@ void init_default_gpio(void) | +----------------------------------------------------------------------------*/ -void update_uart_ios(uart_config_nb_t uart_config) +void update_uart_ios(uart_config_nb_t uart_config, gpio_param_s (*gpio_tab)[GPIO_MAX]) { switch (uart_config) { @@ -1409,7 +1538,7 @@ void update_uart_ios(uart_config_nb_t uart_config) /*----------------------------------------------------------------------------+ | update_ndfc_ios(void). +----------------------------------------------------------------------------*/ -void update_ndfc_ios(void) +void update_ndfc_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { /* Update GPIO Configuration Table */ gpio_tab[GPIO0][6].in_out = GPIO_OUT; /* EBC_CS_N(1) */ @@ -1427,7 +1556,7 @@ void update_ndfc_ios(void) /*----------------------------------------------------------------------------+ | update_zii_ios(void). +----------------------------------------------------------------------------*/ -void update_zii_ios(void) +void update_zii_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { /* Update GPIO Configuration Table */ gpio_tab[GPIO0][12].in_out = GPIO_IN; /* ZII_p0Rxd(0) */ @@ -1477,7 +1606,7 @@ void update_zii_ios(void) /*----------------------------------------------------------------------------+ | update_uic_0_3_irq_ios(). +----------------------------------------------------------------------------*/ -void update_uic_0_3_irq_ios(void) +void update_uic_0_3_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][8].in_out = GPIO_IN; /* UIC_IRQ(0) */ gpio_tab[GPIO1][8].alt_nb = GPIO_ALT1; @@ -1495,7 +1624,7 @@ void update_uic_0_3_irq_ios(void) /*----------------------------------------------------------------------------+ | update_uic_4_9_irq_ios(). +----------------------------------------------------------------------------*/ -void update_uic_4_9_irq_ios(void) +void update_uic_4_9_irq_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][12].in_out = GPIO_IN; /* UIC_IRQ(4) */ gpio_tab[GPIO1][12].alt_nb = GPIO_ALT1; @@ -1516,7 +1645,7 @@ void update_uic_4_9_irq_ios(void) /*----------------------------------------------------------------------------+ | update_dma_a_b_ios(). +----------------------------------------------------------------------------*/ -void update_dma_a_b_ios(void) +void update_dma_a_b_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO1][12].in_out = GPIO_OUT; /* DMA_ACK(1) */ gpio_tab[GPIO1][12].alt_nb = GPIO_ALT2; @@ -1537,7 +1666,7 @@ void update_dma_a_b_ios(void) /*----------------------------------------------------------------------------+ | update_dma_c_d_ios(). +----------------------------------------------------------------------------*/ -void update_dma_c_d_ios(void) +void update_dma_c_d_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][0].in_out = GPIO_IN; /* DMA_REQ(2) */ gpio_tab[GPIO0][0].alt_nb = GPIO_ALT2; @@ -1562,7 +1691,7 @@ void update_dma_c_d_ios(void) /*----------------------------------------------------------------------------+ | update_ebc_master_ios(). +----------------------------------------------------------------------------*/ -void update_ebc_master_ios(void) +void update_ebc_master_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][27].in_out = GPIO_IN; /* EXT_EBC_REQ */ gpio_tab[GPIO0][27].alt_nb = GPIO_ALT1; @@ -1580,7 +1709,7 @@ void update_ebc_master_ios(void) /*----------------------------------------------------------------------------+ | update_usb2_device_ios(). +----------------------------------------------------------------------------*/ -void update_usb2_device_ios(void) +void update_usb2_device_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][26].in_out = GPIO_IN; /* USB2D_RXVALID */ gpio_tab[GPIO0][26].alt_nb = GPIO_ALT2; @@ -1611,20 +1740,21 @@ void update_usb2_device_ios(void) /*----------------------------------------------------------------------------+ | update_pci_patch_ios(). +----------------------------------------------------------------------------*/ -void update_pci_patch_ios(void) +void update_pci_patch_ios(gpio_param_s (*gpio_tab)[GPIO_MAX]) { gpio_tab[GPIO0][29].in_out = GPIO_OUT; /* EBC_EXT_HDLA */ gpio_tab[GPIO0][29].alt_nb = GPIO_ALT1; } /*----------------------------------------------------------------------------+ - | set_chip_gpio_configuration(unsigned char gpio_core) + | set_chip_gpio_configuration(unsigned char gpio_core, + | gpio_param_s (*gpio_tab)[GPIO_MAX]) | Put the core impacted by clock modification and sharing in reset. | Config the select registers to resolve the sharing depending of the config. | Configure the GPIO registers. | +----------------------------------------------------------------------------*/ -void set_chip_gpio_configuration(unsigned char gpio_core) +void set_chip_gpio_configuration(unsigned char gpio_core, gpio_param_s (*gpio_tab)[GPIO_MAX]) { unsigned char i=0, j=0, reg_offset = 0; unsigned long gpio_reg, gpio_core_add; @@ -1778,11 +1908,12 @@ void configure_ppc440ep_pins(void) CORE_NOT_SELECTED /* PCI_PATCH */ }; + gpio_param_s gpio_tab[GPIO_GROUP_MAX][GPIO_MAX]; /* Table Default Initialisation + FPGA Access */ - init_default_gpio(); - set_chip_gpio_configuration(GPIO0); - set_chip_gpio_configuration(GPIO1); + init_default_gpio(gpio_tab); + set_chip_gpio_configuration(GPIO0, gpio_tab); + set_chip_gpio_configuration(GPIO1, gpio_tab); /* Update Table */ force_bup_core_selection(ppc440ep_core_selection, &config_val); @@ -1817,7 +1948,7 @@ void configure_ppc440ep_pins(void) /* UIC 0:3 Selection */ if (ppc440ep_core_selection[UIC_0_3] == CORE_SELECTED) { - update_uic_0_3_irq_ios(); + update_uic_0_3_irq_ios(gpio_tab); dma_a_b_unselect_in_fpga(); } @@ -1825,21 +1956,21 @@ void configure_ppc440ep_pins(void) if (ppc440ep_core_selection[UIC_4_9] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_UICIRQ5_SEL; - update_uic_4_9_irq_ios(); + update_uic_4_9_irq_ios(gpio_tab); } /* DMA AB Selection */ if (ppc440ep_core_selection[DMA_CHANNEL_AB] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_DIS_MASK) | SDR0_PFC1_DIS_DMAR_SEL; - update_dma_a_b_ios(); + update_dma_a_b_ios(gpio_tab); dma_a_b_selection_in_fpga(); } /* DMA CD Selection */ if (ppc440ep_core_selection[DMA_CHANNEL_CD] == CORE_SELECTED) { - update_dma_c_d_ios(); + update_dma_c_d_ios(gpio_tab); dma_c_d_selection_in_fpga(); } @@ -1848,14 +1979,14 @@ void configure_ppc440ep_pins(void) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_ERE_MASK) | SDR0_PFC1_ERE_EXTR_SEL; sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL; - update_ebc_master_ios(); + update_ebc_master_ios(gpio_tab); } /* PCI Patch Enable */ if (ppc440ep_core_selection[PCI_PATCH] == CORE_SELECTED) { sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_EBCHR_SEL; - update_pci_patch_ios(); + update_pci_patch_ios(gpio_tab); } /* USB2 Host Selection - Not Implemented in PowerPC 440EP Pass1 */ @@ -1871,7 +2002,7 @@ void configure_ppc440ep_pins(void) /* USB2.0 Device Selection */ if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED) { - update_usb2_device_ios(); + update_usb2_device_ios(gpio_tab); sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL; sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE; @@ -1904,7 +2035,7 @@ void configure_ppc440ep_pins(void) /* NAND Flash Selection */ if (ppc440ep_core_selection[NAND_FLASH] == CORE_SELECTED) { - update_ndfc_ios(); + update_ndfc_ios(gpio_tab); #if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)) mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL | @@ -1933,7 +2064,7 @@ void configure_ppc440ep_pins(void) /* MII Selection */ if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII; mtsdr(sdr_mfr, sdr0_mfr); @@ -1944,7 +2075,7 @@ void configure_ppc440ep_pins(void) /* RMII Selection */ if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M; mtsdr(sdr_mfr, sdr0_mfr); @@ -1955,7 +2086,7 @@ void configure_ppc440ep_pins(void) /* SMII Selection */ if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED) { - update_zii_ios(); + update_zii_ios(gpio_tab); mfsdr(sdr_mfr, sdr0_mfr); sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII; mtsdr(sdr_mfr, sdr0_mfr); @@ -1992,7 +2123,7 @@ void configure_ppc440ep_pins(void) sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_U1ME_MASK) | SDR0_PFC1_U1ME_DSR_DTR; break; } - update_uart_ios(uart_configuration); + update_uart_ios(uart_configuration, gpio_tab); /* UART Selection in all cases */ uart_selection_in_fpga(uart_configuration); @@ -2014,8 +2145,8 @@ void configure_ppc440ep_pins(void) /* Perform effective access to hardware */ mtsdr(sdr_pfc1, sdr0_pfc1); - set_chip_gpio_configuration(GPIO0); - set_chip_gpio_configuration(GPIO1); + set_chip_gpio_configuration(GPIO0, gpio_tab); + set_chip_gpio_configuration(GPIO1, gpio_tab); /* USB2.0 Device Reset must be done after GPIO setting */ if (ppc440ep_core_selection[USB2_DEVICE] == CORE_SELECTED) diff --git a/board/amcc/bamboo/init.S b/board/amcc/bamboo/init.S index 1459eec..f4d2ae3 100644 --- a/board/amcc/bamboo/init.S +++ b/board/amcc/bamboo/init.S @@ -51,13 +51,12 @@ tlbtab: tlbentry(CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 0, AC_R|AC_W|AC_X|SA_G) #else tlbentry(CFG_NAND_BOOT_SPL_SRC, SZ_4K, CFG_NAND_BOOT_SPL_SRC, 0, AC_R|AC_W|AC_X|SA_G) + tlbentry(CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I) #endif /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ tlbentry(CFG_INIT_RAM_ADDR, SZ_4K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G) - tlbentry(CFG_SDRAM_BASE, SZ_256M, CFG_SDRAM_BASE, 0, AC_R|AC_W|AC_X|SA_G|SA_I) - /* PCI base & peripherals */ tlbentry(CFG_PCI_BASE, SZ_256M, CFG_PCI_BASE, 0, AC_R|AC_W|SA_G|SA_I) diff --git a/board/amcc/bamboo/u-boot.lds b/board/amcc/bamboo/u-boot.lds index f6d7183..0375618 100644 --- a/board/amcc/bamboo/u-boot.lds +++ b/board/amcc/bamboo/u-boot.lds @@ -141,8 +141,6 @@ SECTIONS *(COMMON) } - ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified."); - _end = . ; PROVIDE (end = .); } diff --git a/board/amcc/common/flash.c b/board/amcc/common/flash.c index e6429ec..eba0511 100644 --- a/board/amcc/common/flash.c +++ b/board/amcc/common/flash.c @@ -745,19 +745,27 @@ static ulong flash_get_size_2(vu_long * addr, flash_info_t * info) if (info->flash_id & FLASH_BTYPE) { /* set sector offsets for bottom boot block type */ info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { + info->start[1] = base + 0x00002000; + info->start[2] = base + 0x00004000; + info->start[3] = base + 0x00006000; + info->start[4] = base + 0x00008000; + info->start[5] = base + 0x0000a000; + info->start[6] = base + 0x0000c000; + info->start[7] = base + 0x0000e000; + for (i = 8; i < info->sector_count; i++) { info->start[i] = - base + (i * 0x00010000) - 0x00030000; + base + ((i-7) * 0x00010000); } } else { /* set sector offsets for top boot block type */ i = info->sector_count - 1; + info->start[i--] = base + info->size - 0x00002000; info->start[i--] = base + info->size - 0x00004000; info->start[i--] = base + info->size - 0x00006000; info->start[i--] = base + info->size - 0x00008000; + info->start[i--] = base + info->size - 0x0000a000; + info->start[i--] = base + info->size - 0x0000c000; + info->start[i--] = base + info->size - 0x0000e000; for (; i >= 0; i--) { info->start[i] = base + i * 0x00010000; } diff --git a/common/flash.c b/common/flash.c index a64bc98..888ff9c 100644 --- a/common/flash.c +++ b/common/flash.c @@ -47,16 +47,16 @@ flash_protect (int flag, ulong from, ulong to, flash_info_t *info) short s_end = info->sector_count - 1; /* index of last sector */ int i; - debug ("flash_protect %s: from 0x%08lX to 0x%08lX\n", - (flag & FLAG_PROTECT_SET) ? "ON" : - (flag & FLAG_PROTECT_CLEAR) ? "OFF" : "???", - from, to); - /* Do nothing if input data is bad. */ if (info->sector_count == 0 || info->size == 0 || to < from) { return; } + debug ("flash_protect %s: from 0x%08lX to 0x%08lX\n", + (flag & FLAG_PROTECT_SET) ? "ON" : + (flag & FLAG_PROTECT_CLEAR) ? "OFF" : "???", + from, to); + /* There is nothing to do if we have no data about the flash * or the protect range and flash range don't overlap. */ diff --git a/cpu/ppc4xx/44x_spd_ddr.c b/cpu/ppc4xx/44x_spd_ddr.c index e5f296e..4a4c6f2 100644 --- a/cpu/ppc4xx/44x_spd_ddr.c +++ b/cpu/ppc4xx/44x_spd_ddr.c @@ -269,7 +269,7 @@ struct bank_param { typedef struct bank_param BANKPARMS; #ifdef CFG_SIMULATE_SPD_EEPROM -extern unsigned char cfg_simulate_spd_eeprom[128]; +extern const unsigned char cfg_simulate_spd_eeprom[128]; #endif static unsigned char spd_read(uchar chip, uint addr); diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index d58344d..4e00b9f 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -222,6 +222,8 @@ #define CFG_SIMULATE_SPD_EEPROM 0xff /* simulate spd eeprom on this address */ #define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} #define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ +#define CONFIG_PROG_SDRAM_TLB +#undef CFG_DRAM_TEST /*----------------------------------------------------------------------- * I2C