board/ls2085qds: Add support ethernet

Add support of ethernet:
 - eth.c: mapping lane to slot for (0x2A, 0x07)
 - ls2085a.c: To enable/disable dpmac and get link type

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>

board/freescale/ls2085aqds/Makefile

@@ -6,3 +6,4 @@
 
 obj-y += ls2085aqds.o
 obj-y += ddr.o
+obj-y += eth.o

board/freescale/ls2085aqds/eth.c

@@ -0,0 +1,380 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+#include "../common/qixis.h"
+
+#include "ls2085aqds_qixis.h"
+
+
+#ifdef CONFIG_FSL_MC_ENET
+ /* - In LS2085A there are only 16 SERDES lanes, spread across 2 SERDES banks.
+ *   Bank 1 -> Lanes A, B, C, D, E, F, G, H
+ *   Bank 2 -> Lanes A,B, C, D, E, F, G, H
+ */
+
+ /* Mapping of 16 SERDES lanes to LS2085A QDS board slots. A value of '0' here
+  * means that the mapping must be determined dynamically, or that the lane
+  * maps to something other than a board slot.
+  */
+
+static u8 lane_to_slot_fsm2[] = {
+	0, 0, 0, 0, 0, 0, 0, 0
+};
+
+/* On the Vitesse VSC8234XHG SGMII riser card there are 4 SGMII PHYs
+ * housed.
+ */
+static int riser_phy_addr[] = {
+	SGMII_CARD_PORT1_PHY_ADDR,
+	SGMII_CARD_PORT2_PHY_ADDR,
+	SGMII_CARD_PORT3_PHY_ADDR,
+	SGMII_CARD_PORT4_PHY_ADDR,
+};
+
+/* Slot2 does not have EMI connections */
+#define EMI_NONE	0xFFFFFFFF
+#define EMI1_SLOT1	0
+#define EMI1_SLOT2	1
+#define EMI1_SLOT3	2
+#define EMI1_SLOT4	3
+#define EMI1_SLOT5	4
+#define EMI1_SLOT6	5
+#define EMI2		6
+#define SFP_TX		1
+
+static const char * const mdio_names[] = {
+	"LS2085A_QDS_MDIO0",
+	"LS2085A_QDS_MDIO1",
+	"LS2085A_QDS_MDIO2",
+	"LS2085A_QDS_MDIO3",
+	"LS2085A_QDS_MDIO4",
+	"LS2085A_QDS_MDIO5",
+	DEFAULT_WRIOP_MDIO2_NAME,
+};
+
+struct ls2085a_qds_mdio {
+	u8 muxval;
+	struct mii_dev *realbus;
+};
+
+static const char *ls2085a_qds_mdio_name_for_muxval(u8 muxval)
+{
+	return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+	struct mii_dev *bus;
+	const char *name = ls2085a_qds_mdio_name_for_muxval(muxval);
+
+	if (!name) {
+		printf("No bus for muxval %x\n", muxval);
+		return NULL;
+	}
+
+	bus = miiphy_get_dev_by_name(name);
+
+	if (!bus) {
+		printf("No bus by name %s\n", name);
+		return NULL;
+	}
+
+	return bus;
+}
+
+static void ls2085a_qds_enable_SFP_TX(u8 muxval)
+{
+	u8 brdcfg9;
+
+	brdcfg9 = QIXIS_READ(brdcfg[9]);
+	brdcfg9 &= ~BRDCFG9_SFPTX_MASK;
+	brdcfg9 |= (muxval << BRDCFG9_SFPTX_SHIFT);
+	QIXIS_WRITE(brdcfg[9], brdcfg9);
+}
+
+static void ls2085a_qds_mux_mdio(u8 muxval)
+{
+	u8 brdcfg4;
+
+	if (muxval <= 5) {
+		brdcfg4 = QIXIS_READ(brdcfg[4]);
+		brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+		brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+		QIXIS_WRITE(brdcfg[4], brdcfg4);
+	}
+}
+
+static int ls2085a_qds_mdio_read(struct mii_dev *bus, int addr,
+				 int devad, int regnum)
+{
+	struct ls2085a_qds_mdio *priv = bus->priv;
+
+	ls2085a_qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int ls2085a_qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+				  int regnum, u16 value)
+{
+	struct ls2085a_qds_mdio *priv = bus->priv;
+
+	ls2085a_qds_mux_mdio(priv->muxval);
+
+	return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int ls2085a_qds_mdio_reset(struct mii_dev *bus)
+{
+	struct ls2085a_qds_mdio *priv = bus->priv;
+
+	return priv->realbus->reset(priv->realbus);
+}
+
+static int ls2085a_qds_mdio_init(char *realbusname, u8 muxval)
+{
+	struct ls2085a_qds_mdio *pmdio;
+	struct mii_dev *bus = mdio_alloc();
+
+	if (!bus) {
+		printf("Failed to allocate ls2085a_qds MDIO bus\n");
+		return -1;
+	}
+
+	pmdio = malloc(sizeof(*pmdio));
+	if (!pmdio) {
+		printf("Failed to allocate ls2085a_qds private data\n");
+		free(bus);
+		return -1;
+	}
+
+	bus->read = ls2085a_qds_mdio_read;
+	bus->write = ls2085a_qds_mdio_write;
+	bus->reset = ls2085a_qds_mdio_reset;
+	sprintf(bus->name, ls2085a_qds_mdio_name_for_muxval(muxval));
+
+	pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+	if (!pmdio->realbus) {
+		printf("No bus with name %s\n", realbusname);
+		free(bus);
+		free(pmdio);
+		return -1;
+	}
+
+	pmdio->muxval = muxval;
+	bus->priv = pmdio;
+
+	return mdio_register(bus);
+}
+
+/*
+ * Initialize the dpmac_info array.
+ *
+ */
+static void initialize_dpmac_to_slot(void)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
+				FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
+		>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+	int serdes2_prtcl = (in_le32(&gur->rcwsr[28]) &
+				FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
+		>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
+
+
+	switch (serdes1_prtcl) {
+	case 0x2A:
+		printf("qds: WRIOP: Supported SerDes Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		break;
+	}
+
+	switch (serdes2_prtcl) {
+	case 0x07:
+	case 0x08:
+		printf("qds: WRIOP: Supported SerDes Protocol 0x%02x\n",
+		       serdes2_prtcl);
+		lane_to_slot_fsm2[0] = EMI1_SLOT4;
+		lane_to_slot_fsm2[1] = EMI1_SLOT4;
+		lane_to_slot_fsm2[2] = EMI1_SLOT4;
+		lane_to_slot_fsm2[3] = EMI1_SLOT4;
+		/* No MDIO physical connection */
+		lane_to_slot_fsm2[4] = EMI1_SLOT6;
+		lane_to_slot_fsm2[5] = EMI1_SLOT6;
+		lane_to_slot_fsm2[6] = EMI1_SLOT6;
+		lane_to_slot_fsm2[7] = EMI1_SLOT6;
+		break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes2_prtcl);
+		break;
+	}
+}
+
+void ls2085a_handle_phy_interface_sgmii(int dpmac_id)
+{
+	int lane, slot;
+	struct mii_dev *bus;
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
+				FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
+		>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+	int serdes2_prtcl = (in_le32(&gur->rcwsr[28]) &
+				FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK)
+		>> FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT;
+
+	switch (serdes1_prtcl) {
+	}
+
+	switch (serdes2_prtcl) {
+	case 0x07:
+	case 0x08:
+		lane = serdes_get_first_lane(FSL_SRDS_2, SGMII9 +
+							(dpmac_id - 9));
+		slot = lane_to_slot_fsm2[lane];
+
+		switch (++slot) {
+		case 1:
+			break;
+		case 3:
+			break;
+		case 4:
+			/* Slot housing a SGMII riser card? */
+			wriop_set_phy_address(dpmac_id,
+					      riser_phy_addr[dpmac_id - 9]);
+			dpmac_info[dpmac_id].board_mux = EMI1_SLOT4;
+			bus = mii_dev_for_muxval(EMI1_SLOT4);
+			wriop_set_mdio(dpmac_id, bus);
+			dpmac_info[dpmac_id].phydev = phy_connect(
+						dpmac_info[dpmac_id].bus,
+						dpmac_info[dpmac_id].phy_addr,
+						NULL,
+						dpmac_info[dpmac_id].enet_if);
+			phy_config(dpmac_info[dpmac_id].phydev);
+		break;
+		case 5:
+		break;
+		case 6:
+			/* Slot housing a SGMII riser card? */
+			wriop_set_phy_address(dpmac_id,
+					      riser_phy_addr[dpmac_id - 13]);
+			dpmac_info[dpmac_id].board_mux = EMI1_SLOT6;
+			bus = mii_dev_for_muxval(EMI1_SLOT6);
+			wriop_set_mdio(dpmac_id, bus);
+		break;
+	}
+	break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes2_prtcl);
+	break;
+	}
+}
+void ls2085a_handle_phy_interface_xsgmii(int i)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
+				FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK)
+		>> FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT;
+
+	switch (serdes1_prtcl) {
+	case 0x2A:
+		/*
+		 * XFI does not need a PHY to work, but to avoid U-boot use
+		 * default PHY address which is zero to a MAC when it found
+		 * a MAC has no PHY address, we give a PHY address to XFI
+		 * MAC, and should not use a real XAUI PHY address, since
+		 * MDIO can access it successfully, and then MDIO thinks
+		 * the XAUI card is used for the XFI MAC, which will cause
+		 * error.
+		 */
+		wriop_set_phy_address(i, i + 4);
+		ls2085a_qds_enable_SFP_TX(SFP_TX);
+
+		break;
+	default:
+		printf("qds: WRIOP: Unsupported SerDes Protocol 0x%02x\n",
+		       serdes1_prtcl);
+		break;
+	}
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	int error;
+#ifdef CONFIG_FSL_MC_ENET
+	struct memac_mdio_info *memac_mdio0_info;
+	struct memac_mdio_info *memac_mdio1_info;
+	unsigned int i;
+
+	initialize_dpmac_to_slot();
+
+	memac_mdio0_info = (struct memac_mdio_info *)malloc(
+					sizeof(struct memac_mdio_info));
+	memac_mdio0_info->regs =
+		(struct memac_mdio_controller *)
+					CONFIG_SYS_FSL_WRIOP1_MDIO1;
+	memac_mdio0_info->name = DEFAULT_WRIOP_MDIO1_NAME;
+
+	/* Register the real MDIO1 bus */
+	fm_memac_mdio_init(bis, memac_mdio0_info);
+
+	memac_mdio1_info = (struct memac_mdio_info *)malloc(
+					sizeof(struct memac_mdio_info));
+	memac_mdio1_info->regs =
+		(struct memac_mdio_controller *)
+					CONFIG_SYS_FSL_WRIOP1_MDIO2;
+	memac_mdio1_info->name = DEFAULT_WRIOP_MDIO2_NAME;
+
+	/* Register the real MDIO2 bus */
+	fm_memac_mdio_init(bis, memac_mdio1_info);
+
+	/* Register the muxing front-ends to the MDIO buses */
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT1);
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT2);
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT3);
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT4);
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT5);
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT6);
+
+	ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO2_NAME, EMI2);
+
+	for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
+		switch (wriop_get_enet_if(i)) {
+		case PHY_INTERFACE_MODE_QSGMII:
+			break;
+		case PHY_INTERFACE_MODE_SGMII:
+			ls2085a_handle_phy_interface_sgmii(i);
+			break;
+		case PHY_INTERFACE_MODE_XGMII:
+			ls2085a_handle_phy_interface_xsgmii(i);
+			break;
+		default:
+			break;
+		}
+	}
+
+	error = cpu_eth_init(bis);
+#endif
+	error = pci_eth_init(bis);
+	return error;
+}

board/freescale/ls2085aqds/ls2085aqds.c

@@ -214,19 +214,6 @@ unsigned long get_dram_size_to_hide(void)
 	return dram_to_hide;
 }
 
-int board_eth_init(bd_t *bis)
-{
-	int error = 0;
-
-#ifdef CONFIG_FSL_MC_ENET
-	error = cpu_eth_init(bis);
-#endif
-
-	error = pci_eth_init(bis);
-
-	return error;
-}
-
 #ifdef CONFIG_FSL_MC_ENET
 void fdt_fixup_board_enet(void *fdt)
 {

board/freescale/ls2085aqds/ls2085aqds_qixis.h

@@ -23,4 +23,8 @@
 #define QIXIS_DDRCLK_125		0x2
 #define QIXIS_DDRCLK_133		0x3
 
+#define BRDCFG4_EMISEL_MASK		0xE0
+#define BRDCFG4_EMISEL_SHIFT		5
+#define BRDCFG9_SFPTX_MASK		0x10
+#define BRDCFG9_SFPTX_SHIFT		4
 #endif /*__LS2_QDS_QIXIS_H__*/

drivers/net/ldpaa_eth/Makefile

@@ -6,3 +6,4 @@
 
 obj-y += ldpaa_wriop.o
 obj-y += ldpaa_eth.o
+obj-$(CONFIG_LS2085A) += ls2085a.o

drivers/net/ldpaa_eth/ls2085a.c

@@ -0,0 +1,83 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <phy.h>
+#include <fsl-mc/ldpaa_wriop.h>
+#include <asm/io.h>
+#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include <asm/arch/fsl_serdes.h>
+#include <fsl-mc/ldpaa_wriop.h>
+
+u32 dpmac_to_devdisr[] = {
+	[WRIOP1_DPMAC1] = FSL_CHASSIS3_DEVDISR2_DPMAC1,
+	[WRIOP1_DPMAC2] = FSL_CHASSIS3_DEVDISR2_DPMAC2,
+	[WRIOP1_DPMAC3] = FSL_CHASSIS3_DEVDISR2_DPMAC3,
+	[WRIOP1_DPMAC4] = FSL_CHASSIS3_DEVDISR2_DPMAC4,
+	[WRIOP1_DPMAC5] = FSL_CHASSIS3_DEVDISR2_DPMAC5,
+	[WRIOP1_DPMAC6] = FSL_CHASSIS3_DEVDISR2_DPMAC6,
+	[WRIOP1_DPMAC7] = FSL_CHASSIS3_DEVDISR2_DPMAC7,
+	[WRIOP1_DPMAC8] = FSL_CHASSIS3_DEVDISR2_DPMAC8,
+	[WRIOP1_DPMAC9] = FSL_CHASSIS3_DEVDISR2_DPMAC9,
+	[WRIOP1_DPMAC10] = FSL_CHASSIS3_DEVDISR2_DPMAC10,
+	[WRIOP1_DPMAC11] = FSL_CHASSIS3_DEVDISR2_DPMAC11,
+	[WRIOP1_DPMAC12] = FSL_CHASSIS3_DEVDISR2_DPMAC12,
+	[WRIOP1_DPMAC13] = FSL_CHASSIS3_DEVDISR2_DPMAC13,
+	[WRIOP1_DPMAC14] = FSL_CHASSIS3_DEVDISR2_DPMAC14,
+	[WRIOP1_DPMAC15] = FSL_CHASSIS3_DEVDISR2_DPMAC15,
+	[WRIOP1_DPMAC16] = FSL_CHASSIS3_DEVDISR2_DPMAC16,
+	[WRIOP1_DPMAC17] = FSL_CHASSIS3_DEVDISR2_DPMAC17,
+	[WRIOP1_DPMAC18] = FSL_CHASSIS3_DEVDISR2_DPMAC18,
+	[WRIOP1_DPMAC19] = FSL_CHASSIS3_DEVDISR2_DPMAC19,
+	[WRIOP1_DPMAC20] = FSL_CHASSIS3_DEVDISR2_DPMAC20,
+	[WRIOP1_DPMAC21] = FSL_CHASSIS3_DEVDISR2_DPMAC21,
+	[WRIOP1_DPMAC22] = FSL_CHASSIS3_DEVDISR2_DPMAC22,
+	[WRIOP1_DPMAC23] = FSL_CHASSIS3_DEVDISR2_DPMAC23,
+	[WRIOP1_DPMAC24] = FSL_CHASSIS3_DEVDISR2_DPMAC24,
+};
+
+static int is_device_disabled(int dpmac_id)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+	u32 devdisr2 = in_le32(&gur->devdisr2);
+
+	return dpmac_to_devdisr[dpmac_id] & devdisr2;
+}
+
+void wriop_dpmac_disable(int dpmac_id)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+
+	setbits_le32(&gur->devdisr2, dpmac_to_devdisr[dpmac_id]);
+}
+
+void wriop_dpmac_enable(int dpmac_id)
+{
+	struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
+
+	clrbits_le32(&gur->devdisr2, dpmac_to_devdisr[dpmac_id]);
+}
+
+phy_interface_t wriop_dpmac_enet_if(int dpmac_id, int lane_prtcl)
+{
+	enum srds_prtcl;
+
+	if (is_device_disabled(dpmac_id + 1))
+		return PHY_INTERFACE_MODE_NONE;
+
+	if (lane_prtcl >= SGMII1 && lane_prtcl <= SGMII16)
+		return PHY_INTERFACE_MODE_SGMII;
+
+	if (lane_prtcl >= XFI1 && lane_prtcl <= XFI8)
+		return PHY_INTERFACE_MODE_XGMII;
+
+	if (lane_prtcl >= XAUI1 && lane_prtcl <= XAUI2)
+		return PHY_INTERFACE_MODE_XGMII;
+
+	if (lane_prtcl >= QSGMII_A && lane_prtcl <= QSGMII_D)
+		return PHY_INTERFACE_MODE_QSGMII;
+
+	return PHY_INTERFACE_MODE_NONE;
+}

include/configs/ls2085aqds.h

@@ -280,4 +280,23 @@ unsigned long get_board_ddr_clk(void);
 	"kernel_load=0xa0000000\0"		\
 	"kernel_size=0x1000000\0"
 
+#ifdef CONFIG_FSL_MC_ENET
+#define CONFIG_FSL_MEMAC
+#define	CONFIG_PHYLIB
+#define CONFIG_PHYLIB_10G
+#define	CONFIG_CMD_MII
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"DPNI1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+#endif
+
 #endif /* __LS2_QDS_H */