Whitebox
/
u-boot
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

board: at91sam9m10g45ek: Clean up code

Browse Source 
Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
master
Wenyou Yang 8 years ago committed by Simon Glass
parent 59b37122b1
commit e95a29e4e5
1 changed files with 0 additions and 102 deletions
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Show Stats Download Patch File Download Diff File
  1. 102
      board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c

102
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
Unescape View File

@ -17,11 +17,6 @@
#include <lcd.h>
#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@ -149,39 +144,6 @@ static void at91sam9m10g45ek_usb_hw_init(void)
}
#endif
#ifdef CONFIG_MACB
static void at91sam9m10g45ek_macb_hw_init(void)
{
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
at91_periph_clk_enable(ATMEL_ID_EMAC);
/*
* Disable pull-up on:
* RXDV (PA15) => PHY normal mode (not Test mode)
* ERX0 (PA12) => PHY ADDR0
* ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA12) |
pin_to_mask(AT91_PIN_PA13),
&pioa->pudr);
at91_phy_reset();
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA12) |
pin_to_mask(AT91_PIN_PA13),
&pioa->puer);
/* And the pins. */
at91_macb_hw_init();
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
@ -280,18 +242,8 @@ void lcd_show_board_info(void)
#endif /* CONFIG_LCD_INFO */
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
int board_mmc_init(bd_t *bis)
{
at91_mci_hw_init();
return atmel_mci_init((void *)ATMEL_BASE_MCI0);
}
#endif
int board_early_init_f(void)
{
at91_seriald_hw_init();
return 0;
}
@ -313,15 +265,6 @@ int board_init(void)
#ifdef CONFIG_CMD_USB
at91sam9m10g45ek_usb_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_ATMEL_SPI
at91_spi0_hw_init(1 << 4);
#endif
#ifdef CONFIG_MACB
at91sam9m10g45ek_macb_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9m10g45ek_lcd_hw_init();
#endif
@ -340,48 +283,3 @@ void reset_phy(void)
{
}
#endif
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
#endif
return rc;
}
/* SPI chip select control */
#ifdef CONFIG_ATMEL_SPI
#include <spi.h>
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs < 2;
}
void spi_cs_activate(struct spi_slave *slave)
{
switch(slave->cs) {
case 1:
at91_set_gpio_output(AT91_PIN_PB18, 0);
break;
case 0:
default:
at91_set_gpio_output(AT91_PIN_PB3, 0);
break;
}
}
void spi_cs_deactivate(struct spi_slave *slave)
{
switch(slave->cs) {
case 1:
at91_set_gpio_output(AT91_PIN_PB18, 1);
break;
case 0:
default:
at91_set_gpio_output(AT91_PIN_PB3, 1);
break;
}
}
#endif /* CONFIG_ATMEL_SPI */

Write Preview
Loading…
Cancel
Save