ARM: OMAP5: Clean up iosettings code

There is some code duplication in the ddr io settings code.
This is avoided by moving the data to a Soc specific place and
letting the code generic.

This avoids unnessecary code addition for future socs.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>

arch/arm/cpu/armv7/omap5/hw_data.c

@@ -32,6 +32,7 @@
 #include <asm/arch/clocks.h>
 #include <asm/omap_gpio.h>
 #include <asm/io.h>
+#include <asm/emif.h>
 
 struct prcm_regs const **prcm =
 			(struct prcm_regs const **) OMAP_SRAM_SCRATCH_PRCM_PTR;
@@ -414,6 +415,24 @@ void enable_non_essential_clocks(void)
 			MODULE_CLKCTRL_MODULEMODE_SHIFT);
 }
 
+const struct ctrl_ioregs ioregs_omap5430 = {
+	.ctrl_ddrch = DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+	.ctrl_lpddr2ch = DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
+	.ctrl_ddrio_0 = DDR_IO_0_DDR2_DQ_INT_EN_ALL_DDR3_CA_DIS_ALL,
+	.ctrl_ddrio_1 = DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL,
+	.ctrl_ddrio_2 = DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL,
+};
+
+const struct ctrl_ioregs ioregs_omap5432_es1 = {
+	.ctrl_ddrch = DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+	.ctrl_lpddr2ch = 0x0,
+	.ctrl_ddr3ch = DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
+	.ctrl_ddrio_0 = DDR_IO_0_VREF_CELLS_DDR3_VALUE,
+	.ctrl_ddrio_1 = DDR_IO_1_VREF_CELLS_DDR3_VALUE,
+	.ctrl_ddrio_2 = DDR_IO_2_VREF_CELLS_DDR3_VALUE,
+	.ctrl_emif_sdram_config_ext = SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
+};
+
 void hw_data_init(void)
 {
 	u32 omap_rev = omap_revision();
@@ -438,3 +457,20 @@ void hw_data_init(void)
 
 	*ctrl = &omap5_ctrl;
 }
+
+void get_ioregs(const struct ctrl_ioregs **regs)
+{
+	u32 omap_rev = omap_revision();
+
+	switch (omap_rev) {
+	case OMAP5430_ES1_0:
+		*regs = &ioregs_omap5430;
+	break;
+	case OMAP5432_ES1_0:
+		*regs = &ioregs_omap5432_es1;
+	break;
+
+	default:
+		printf("\n INVALID OMAP REVISION ");
+	}
+}

arch/arm/cpu/armv7/omap5/hwinit.c

@@ -56,60 +56,47 @@ const struct gpio_bank *const omap_gpio_bank = gpio_bank_54xx;
 /* LPDDR2 specific IO settings */
 static void io_settings_lpddr2(void)
 {
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
-				(*ctrl)->control_ddrch1_0);
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
-				(*ctrl)->control_ddrch1_1);
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
-				(*ctrl)->control_ddrch2_0);
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
-				(*ctrl)->control_ddrch2_1);
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
-				(*ctrl)->control_lpddr2ch1_0);
-	writel(DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
-				(*ctrl)->control_lpddr2ch1_1);
-	writel(DDR_IO_0_DDR2_DQ_INT_EN_ALL_DDR3_CA_DIS_ALL,
-				(*ctrl)->control_ddrio_0);
-	writel(DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL,
-				(*ctrl)->control_ddrio_1);
-	writel(DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL,
-				(*ctrl)->control_ddrio_2);
+	const struct ctrl_ioregs *ioregs;
+
+	get_ioregs(&ioregs);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
+	writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
+	writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
+	writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
 }
 
 /* DDR3 specific IO settings */
 static void io_settings_ddr3(void)
 {
 	u32 io_settings = 0;
+	const struct ctrl_ioregs *ioregs;
 
-	writel(DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddr3ch1_0);
-	writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddrch1_0);
-	writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddrch1_1);
-
-	writel(DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddr3ch2_0);
-	writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddrch2_0);
-	writel(DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
-				(*ctrl)->control_ddrch2_1);
-
-	writel(DDR_IO_0_VREF_CELLS_DDR3_VALUE,
-				(*ctrl)->control_ddrio_0);
-	writel(DDR_IO_1_VREF_CELLS_DDR3_VALUE,
-				(*ctrl)->control_ddrio_1);
-	writel(DDR_IO_2_VREF_CELLS_DDR3_VALUE,
-				(*ctrl)->control_ddrio_2);
+	get_ioregs(&ioregs);
+	writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
+
+	writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
+
+	writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
+	writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
+	writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
 
 	/* omap5432 does not use lpddr2 */
-	writel(0x0, (*ctrl)->control_lpddr2ch1_0);
-	writel(0x0, (*ctrl)->control_lpddr2ch1_1);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
 
-	writel(SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
-			(*ctrl)->control_emif1_sdram_config_ext);
-	writel(SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
-			(*ctrl)->control_emif2_sdram_config_ext);
+	writel(ioregs->ctrl_emif_sdram_config_ext,
+	       (*ctrl)->control_emif1_sdram_config_ext);
+	writel(ioregs->ctrl_emif_sdram_config_ext,
+	       (*ctrl)->control_emif2_sdram_config_ext);
 
 	/* Disable DLL select */
 	io_settings = (readl((*ctrl)->control_port_emif1_sdram_config)

arch/arm/include/asm/arch-omap5/omap.h

@@ -229,5 +229,15 @@ struct omap_boot_parameters {
 	unsigned char reset_reason;
 	unsigned char ch_flags;
 };
+
+struct ctrl_ioregs {
+	u32 ctrl_ddrch;
+	u32 ctrl_lpddr2ch;
+	u32 ctrl_ddr3ch;
+	u32 ctrl_ddrio_0;
+	u32 ctrl_ddrio_1;
+	u32 ctrl_ddrio_2;
+	u32 ctrl_emif_sdram_config_ext;
+};
 #endif /* __ASSEMBLY__ */
 #endif

arch/arm/include/asm/arch-omap5/sys_proto.h

@@ -58,6 +58,7 @@ void omap_vc_init(u16 speed_khz);
 int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data);
 u32 warm_reset(void);
 void force_emif_self_refresh(void);
+void get_ioregs(const struct ctrl_ioregs **regs);
 
 /*
  * This is used to verify if the configuration header