armv8: ls1046ardb: Add RDIMM support

This adds 2Rx8 RDIMM on LS1046ARDB board. Tested with RDIMM
MTA18ASF2G72PDZ and MTA9ASF1G72PZ.

Signed-off-by: York Sun <york.sun@nxp.com>

board/freescale/ls1046ardb/ddr.c

@@ -29,7 +29,10 @@ void fsl_ddr_board_options(memctl_options_t *popts,
 	if (!pdimm->n_ranks)
 		return;
 
-	pbsp = udimms[0];
+	if (popts->registered_dimm_en)
+		pbsp = rdimms[0];
+	else
+		pbsp = udimms[0];
 
 	/* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
 	 * freqency and n_banks specified in board_specific_parameters table.
@@ -66,8 +69,6 @@ found:
 	      pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
 
 	popts->data_bus_width = 0;	/* 64-bit data bus */
-	popts->otf_burst_chop_en = 0;
-	popts->burst_length = DDR_BL8;
 	popts->bstopre = 0;		/* enable auto precharge */
 
 	/*
@@ -94,7 +95,7 @@ found:
 			  DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
 
 	/* optimize cpo for erratum A-009942 */
-	popts->cpo_sample = 0x70;
+	popts->cpo_sample = 0x61;
 }
 
 int fsl_initdram(void)

board/freescale/ls1046ardb/ddr.h

@@ -41,4 +41,23 @@ static const struct board_specific_parameters *udimms[] = {
 	udimm0,
 };
 
+static const struct board_specific_parameters rdimm0[] = {
+	/*
+	 * memory controller 0
+	 *   num|  hi| rank|  clk| wrlvl |   wrlvl   |  wrlvl
+	 * ranks| mhz| GB  |adjst| start |   ctl2    |  ctl3
+	 */
+	{2,  1666, 0, 0x8,     0x0D, 0x0C0B0A08, 0x0A0B0C08,},
+	{2,  1900, 0, 0x8,     0x0E, 0x0D0C0B09, 0x0B0C0D09,},
+	{2,  2300, 0, 0xa,     0x12, 0x100F0D0C, 0x0E0F100C,},
+	{1,  1666, 0, 0x8,     0x0D, 0x0C0B0A08, 0x0A0B0C08,},
+	{1,  1900, 0, 0x8,     0x0E, 0x0D0C0B09, 0x0B0C0D09,},
+	{1,  2300, 0, 0xa,     0x12, 0x100F0D0C, 0x0E0F100C,},
+	{}
+};
+
+static const struct board_specific_parameters *rdimms[] = {
+	rdimm0,
+};
+
 #endif