Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'

11 years ago · fae56934a0
parent 9ed679aeeb 11f2968706
commit fae56934a0
36 changed files with 2323 additions and 36 deletions
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@ -36,11 +36,15 @@

 DECLARE_GLOBAL_DATA_PTR;

-static const struct gpio_bank gpio_bank_am33xx[4] = {
+static const struct gpio_bank gpio_bank_am33xx[] = {
 	{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
 	{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
 	{ (void *)AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
 	{ (void *)AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
+#ifdef CONFIG_AM43XX
+	{ (void *)AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
+	{ (void *)AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
+#endif
 };

 const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
--- a/arch/arm/cpu/armv7/am33xx/clock_am43xx.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_am43xx.c
@ -94,6 +94,8 @@ void enable_basic_clocks(void)
 		&cmper->gpio1clkctrl,
 		&cmper->gpio2clkctrl,
 		&cmper->gpio3clkctrl,
+		&cmper->gpio4clkctrl,
+		&cmper->gpio5clkctrl,
 		&cmper->i2c1clkctrl,
 		&cmper->emiffwclkctrl,
 		&cmper->emifclkctrl,
--- a/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
+++ b/arch/arm/cpu/armv7/am33xx/clock_ti814x.c
@ -211,11 +211,8 @@ static u32 pll_dco_freq_sel(u32 clkout_dco)
 static u32 pll_sigma_delta_val(u32 clkout_dco)
 {
 	u32 sig_val = 0;
-	float frac_div;

-	frac_div = (float) clkout_dco / 250;
-	frac_div = frac_div + 0.90;
-	sig_val = (int)frac_div;
+	sig_val = (clkout_dco + 225) / 250;
 	sig_val = sig_val << 24;

 	return sig_val;
--- a/arch/arm/cpu/armv7/omap4/hw_data.c
+++ b/arch/arm/cpu/armv7/omap4/hw_data.c
@ -172,6 +172,20 @@ struct dplls omap4430_dplls_es1 = {
 	.ddr = NULL
 };

+struct dplls omap4430_dplls_es20 = {
+	.mpu = mpu_dpll_params_1200mhz,
+	.core = core_dpll_params_es2_1600mhz_ddr200mhz,
+	.per = per_dpll_params_1536mhz,
+	.iva = iva_dpll_params_1862mhz,
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+	.abe = abe_dpll_params_sysclk_196608khz,
+#else
+	.abe = &abe_dpll_params_32k_196608khz,
+#endif
+	.usb = usb_dpll_params_1920mhz,
+	.ddr = NULL
+};
+
 struct dplls omap4430_dplls = {
 	.mpu = mpu_dpll_params_1200mhz,
 	.core = core_dpll_params_1600mhz,
@ -413,6 +427,10 @@ void hw_data_init(void)
 	break;

 	case OMAP4430_ES2_0:
+	*dplls_data = &omap4430_dplls_es20;
+	*omap_vcores = &omap4430_volts;
+	break;
+
 	case OMAP4430_ES2_1:
 	case OMAP4430_ES2_2:
 	case OMAP4430_ES2_3:
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@ -432,7 +432,7 @@ struct omap_sys_ctrl_regs const dra7xx_ctrl = {
 	.control_srcomp_code_latch		= 0x4A002E84,
 	.control_ddr_control_ext_0		= 0x4A002E88,
 	.control_padconf_core_base		= 0x4A003400,
-	.control_std_fuse_opp_vdd_mpu_2		= 0x4A003B24,
+	.control_std_fuse_opp_vdd_mpu_2		= 0x4A003B20,
 	.control_port_emif1_sdram_config	= 0x4AE0C110,
 	.control_port_emif1_lpddr2_nvm_config	= 0x4AE0C114,
 	.control_port_emif2_sdram_config	= 0x4AE0C118,
--- a/arch/arm/include/asm/arch-am33xx/cpu.h
+++ b/arch/arm/include/asm/arch-am33xx/cpu.h
@ -171,7 +171,8 @@ struct cm_wkuppll {
 	unsigned int resv11[1];
 	unsigned int wkup_uart0ctrl;	/* offset 0xB4 */
 	unsigned int wkup_i2c0ctrl;	/* offset 0xB8 */
-	unsigned int resv12[7];
+	unsigned int wkup_adctscctrl;	/* offset 0xBC */
+	unsigned int resv12[6];
 	unsigned int divm6dpllcore;	/* offset 0xD8 */
 };

@ -221,7 +222,8 @@ struct cm_perpll {
 	unsigned int tpccclkctrl;	/* offset 0xBC */
 	unsigned int dcan0clkctrl;	/* offset 0xC0 */
 	unsigned int dcan1clkctrl;	/* offset 0xC4 */
-	unsigned int resv6[2];
+	unsigned int resv6;
+	unsigned int epwmss1clkctrl;	/* offset 0xCC */
 	unsigned int emiffwclkctrl;	/* offset 0xD0 */
 	unsigned int epwmss0clkctrl;	/* offset 0xD4 */
 	unsigned int epwmss2clkctrl;	/* offset 0xD8 */
@ -351,7 +353,11 @@ struct cm_perpll {
 	unsigned int gpio2clkctrl;	/* offset 0x480 */
 	unsigned int resv20;
 	unsigned int gpio3clkctrl;	/* offset 0x488 */
-	unsigned int resv21[7];
+	unsigned int resv41;
+	unsigned int gpio4clkctrl;	/* offset 0x490 */
+	unsigned int resv42;
+	unsigned int gpio5clkctrl;	/* offset 0x498 */
+	unsigned int resv21[3];

 	unsigned int i2c1clkctrl;	/* offset 0x4A8 */
 	unsigned int resv22;
--- a/arch/arm/include/asm/arch-am33xx/ddr_defs.h
+++ b/arch/arm/include/asm/arch-am33xx/ddr_defs.h
@ -58,6 +58,22 @@
 #define MT41J128MJT125_PHY_FIFO_WE		0x100
 #define MT41J128MJT125_IOCTRL_VALUE		0x18B

+/* Micron MT41K128M16JT-187E */
+#define MT41K128MJT187E_EMIF_READ_LATENCY	0x06
+#define MT41K128MJT187E_EMIF_TIM1		0x0888B3DB
+#define MT41K128MJT187E_EMIF_TIM2		0x36337FDA
+#define MT41K128MJT187E_EMIF_TIM3		0x501F830F
+#define MT41K128MJT187E_EMIF_SDCFG		0x61C04AB2
+#define MT41K128MJT187E_EMIF_SDREF		0x0000093B
+#define MT41K128MJT187E_ZQ_CFG			0x50074BE4
+#define MT41K128MJT187E_RATIO			0x40
+#define MT41K128MJT187E_INVERT_CLKOUT		0x1
+#define MT41K128MJT187E_RD_DQS			0x3B
+#define MT41K128MJT187E_WR_DQS			0x85
+#define MT41K128MJT187E_PHY_WR_DATA		0xC1
+#define MT41K128MJT187E_PHY_FIFO_WE		0x100
+#define MT41K128MJT187E_IOCTRL_VALUE		0x18B
+
 /* Micron MT41J64M16JT-125 */
 #define MT41J64MJT125_EMIF_SDCFG		0x61C04A32

--- a/arch/arm/include/asm/arch-am33xx/gpio.h
+++ b/arch/arm/include/asm/arch-am33xx/gpio.h
@ -12,8 +12,8 @@
 #define AM33XX_GPIO1_BASE       0x4804C000
 #define AM33XX_GPIO2_BASE       0x481AC000
 #define AM33XX_GPIO3_BASE       0x481AE000
-
-#define GPIO_22			22
+#define AM33XX_GPIO4_BASE	0x48320000
+#define AM33XX_GPIO5_BASE	0x48322000

 /* GPIO CTRL register */
 #define GPIO_CTRL_DISABLEMODULE_SHIFT	0
--- a/board/BuR/common/bur_common.h
+++ b/board/BuR/common/bur_common.h
@ -0,0 +1,22 @@
+/*
+ * bur_comon.h
+ *
+ * common board information header for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BUR_COMMON_H_
+#define _BUR_COMMON_H_
+
+void blink(u32 blinks, u32 intervall, u32 pin);
+void pmicsetup(u32 mpupll);
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+int board_eth_init(bd_t *bis);
+
+#endif
--- a/board/BuR/common/common.c
+++ b/board/BuR/common/common.c
@ -0,0 +1,216 @@
+/*
+ * common.c
+ *
+ * common board functions for B&R boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include "bur_common.h"
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+/* --------------------------------------------------------------------------*/
+void blink(u32 blinks, u32 intervall, u32 pin)
+{
+	gpio_direction_output(pin, 0);
+	int val = 0;
+
+	do {
+		val ^= 0x01;
+		gpio_set_value(pin, val);
+		mdelay(intervall);
+	} while (blinks--);
+
+	gpio_set_value(pin, 0);
+}
+#ifdef CONFIG_SPL_BUILD
+void pmicsetup(u32 mpupll)
+{
+	int mpu_vdd;
+	int usb_cur_lim;
+
+	/* setup I2C */
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	if (i2c_probe(TPS65217_CHIP_PM)) {
+		puts("PMIC (0x24) not found! skip further initalization.\n");
+		return;
+	}
+
+	/* Get the frequency which is defined by device fuses */
+	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+	printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
+
+	if (0 != mpupll) {
+		dpll_mpu_opp100.m = MPUPLL_M_1000;
+		printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
+	} else {
+		puts("ok.\n");
+	}
+	/*
+	 * Increase USB current limit to 1300mA or 1800mA and set
+	 * the MPU voltage controller as needed.
+	 */
+	if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+	} else {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+	}
+
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
+			       usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set DCDC3 (CORE) voltage to 1.125V */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* Set DCDC2 (MPU) voltage */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/* Set LDO3 to 1.8V */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS1,
+			       TPS65217_LDO_VOLTAGE_OUT_1_8,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+	/* Set LDO4 to 3.3V */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS2,
+			       TPS65217_LDO_VOLTAGE_OUT_3_3,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set MPU Frequency to what we detected now that voltages are set */
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+#endif /* CONFIG_SPL_BUILD */
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+	return;
+}
+
+/* describing port offsets of TI's CPSW block */
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+
+#if defined(CONFIG_DRIVER_TI_CPSW)
+
+int board_eth_init(bd_t *bis)
+{
+	int rv = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	/* try reading mac address from efuse */
+	mac_lo = readl(&cdev->macid0l);
+	mac_hi = readl(&cdev->macid0h);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+	mac_addr[4] = mac_lo & 0xFF;
+	mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC ... ");
+
+		if (is_valid_ether_addr(mac_addr)) {
+			printf("using: %02X:%02X:%02X:%02X:%02X:%02X.\n",
+			       mac_addr[0], mac_addr[1], mac_addr[2],
+			       mac_addr[3], mac_addr[4], mac_addr[5]
+				);
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		}
+	}
+	writel(MII_MODE_ENABLE, &cdev->miisel);
+	cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_MII;
+	cpsw_slaves[1].phy_if =	PHY_INTERFACE_MODE_MII;
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0) {
+		printf("Error %d registering CPSW switch\n", rv);
+		return 0;
+	}
+#endif /* CONFIG_DRIVER_TI_CPSW, ... */
+	return rv;
+}
+#endif /* CONFIG_DRIVER_TI_CPSW */
--- a/board/BuR/kwb/Makefile
+++ b/board/BuR/kwb/Makefile
@ -0,0 +1,12 @@
+#
+# Makefile
+#
+# Copyright (C) 2014 Hannes Petermaier <oe5hpm@oevsv.at> -
+# Bernecker & Rainer Industrielektronik GmbH - http://www.br-automation.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-$(CONFIG_SPL_BUILD) += mux.o
+obj-y	+= ../common/common.o
+obj-y	+= board.o
--- a/board/BuR/kwb/board.c
+++ b/board/BuR/kwb/board.c
@ -0,0 +1,240 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R KWB Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+/* -------------------------------------------------------------------------*/
+/* -- defines for used GPIO Hardware -- */
+#define KEY						(0+4)
+#define LCD_PWR						(0+5)
+#define PUSH_KEY					(0+31)
+#define USB2SD_NRST					(32+29)
+#define USB2SD_PWR					(96+13)
+/* -------------------------------------------------------------------------*/
+/* -- PSOC Resetcontroller Register defines -- */
+
+/* I2C Address of controller */
+#define	RSTCTRL_ADDR				0x75
+/* Register for CTRL-word */
+#define RSTCTRL_CTRLREG				0x01
+/* Register for giving some information to VxWorks OS */
+#define RSTCTRL_SCRATCHREG			0x04
+
+/* -- defines for RSTCTRL_CTRLREG  -- */
+#define	RSTCTRL_FORCE_PWR_NEN			0x0404
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	unsigned int oldspeed;
+	unsigned short buf;
+
+	struct cm_perpll *const cmper = (struct cm_perpll *)CM_PER;
+	struct cm_wkuppll *const cmwkup = (struct cm_wkuppll *)CM_WKUP;
+	/*
+	 * enable additional clocks of modules which are accessed later from
+	 * VxWorks OS
+	 */
+	u32 *const clk_domains[] = { 0 };
+
+	u32 *const clk_modules_kwbspecific[] = {
+		&cmwkup->wkup_adctscctrl,
+		&cmper->spi1clkctrl,
+		&cmper->dcan0clkctrl,
+		&cmper->dcan1clkctrl,
+		&cmper->epwmss0clkctrl,
+		&cmper->epwmss1clkctrl,
+		&cmper->epwmss2clkctrl,
+		0
+	};
+	do_enable_clocks(clk_domains, clk_modules_kwbspecific, 1);
+
+	/* power-OFF LCD-Display */
+	gpio_direction_output(LCD_PWR, 0);
+
+	/* setup I2C */
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	/* power-ON  3V3 via Resetcontroller */
+	oldspeed = i2c_get_bus_speed();
+	if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+		buf = RSTCTRL_FORCE_PWR_NEN;
+		i2c_write(RSTCTRL_ADDR, RSTCTRL_CTRLREG, 1,
+			  (uint8_t *)&buf, sizeof(buf));
+		i2c_set_bus_speed(oldspeed);
+	} else {
+		puts("ERROR: i2c_set_bus_speed failed! (turn on PWR_nEN)\n");
+	}
+
+#if defined(CONFIG_AM335X_USB0)
+	/* power on USB2SD Controller */
+	gpio_direction_output(USB2SD_PWR, 1);
+	mdelay(1);
+	/* give a reset Pulse to USB2SD Controller */
+	gpio_direction_output(USB2SD_NRST, 0);
+	mdelay(1);
+	gpio_set_value(USB2SD_NRST, 1);
+#endif
+	pmicsetup(0);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+	config_ddr(400, &ddr3_ioregs,
+		   &ddr3_data,
+		   &ddr3_cmd_ctrl_data,
+		   &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	const unsigned int ton  = 250;
+	const unsigned int toff = 1000;
+	unsigned int cnt  = 3;
+	unsigned short buf = 0xAAAA;
+	unsigned int oldspeed;
+
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+			   TPS65217_WLEDCTRL2, 0x32, 0xFF); /* 50% dimlevel */
+
+	if (gpio_get_value(KEY)) {
+		do {
+			/* turn on light */
+			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+					   TPS65217_WLEDCTRL1, 0x09, 0xFF);
+			mdelay(ton);
+			/* turn off light */
+			tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+					   TPS65217_WLEDCTRL1, 0x01, 0xFF);
+			mdelay(toff);
+			cnt--;
+			if (!gpio_get_value(KEY) &&
+			    gpio_get_value(PUSH_KEY) && 1 == cnt) {
+				puts("updating from USB ...\n");
+				setenv("bootcmd", "run usbupdate");
+				break;
+			} else if (!gpio_get_value(KEY)) {
+				break;
+			}
+		} while (cnt);
+	}
+
+	switch (cnt) {
+	case 0:
+		puts("3 blinks ... entering BOOT mode.\n");
+		buf = 0x0000;
+		break;
+	case 1:
+		puts("2 blinks ... entering DIAGNOSE mode.\n");
+		buf = 0x0F0F;
+		break;
+	case 2:
+		puts("1 blinks ... entering SERVICE mode.\n");
+		buf = 0xB4B4;
+		break;
+	case 3:
+		puts("0 blinks ... entering RUN mode.\n");
+		buf = 0x0404;
+		break;
+	}
+	mdelay(ton);
+	/* turn on light */
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+			   TPS65217_WLEDCTRL1, 0x09, 0xFF);
+	/* write bootinfo into scratchregister of resetcontroller */
+	oldspeed = i2c_get_bus_speed();
+	if (0 != i2c_set_bus_speed(CONFIG_SYS_OMAP24_I2C_SPEED_PSOC)) {
+		i2c_write(RSTCTRL_ADDR, RSTCTRL_SCRATCHREG, 1,
+			  (uint8_t *)&buf, sizeof(buf));
+		i2c_set_bus_speed(oldspeed);
+	} else {
+		puts("ERROR: i2c_set_bus_speed failed! (scratchregister)\n");
+	}
+	/*
+	 * reset VBAR registers to its reset location, VxWorks 6.9.3.2 does
+	 * expect that vectors are there, original u-boot moves them to _start
+	 */
+	__asm__("ldr r0,=0x20000");
+	__asm__("mcr p15, 0, r0, c12, c0, 0"); /* Set VBAR */
+
+	return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
--- a/board/BuR/kwb/mux.c
+++ b/board/BuR/kwb/mux.c
@ -0,0 +1,195 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux usb0_pin_mux[] = {
+	{OFFSET(usb0_id), (MODE(0) | RXACTIVE)},
+	/* USB0 DrvBus Receiver disable (from romcode 0x20) */
+	{OFFSET(usb0_drvvbus), (MODE(0))},
+	/* USB1 DrvBus as GPIO due to HW-Workaround */
+	{OFFSET(usb1_drvvbus), (MODE(7))},
+	{-1},
+};
+static struct module_pin_mux spi1_pin_mux[] = {
+	/* SPI1_SCLK */
+	{OFFSET(mcasp0_aclkx), MODE(3) | PULLUDEN |             RXACTIVE},
+	/* SPI1_D0 */
+	{OFFSET(mcasp0_fsx),   MODE(3) | PULLUDEN |		RXACTIVE},
+	/* SPI1_D1 */
+	{OFFSET(mcasp0_axr0),  MODE(3) | PULLUDEN |             RXACTIVE},
+	/* SPI1_CS0 */
+	{OFFSET(mcasp0_ahclkr), MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux dcan0_pin_mux[] = {
+	/* DCAN0 TX */
+	{OFFSET(uart1_ctsn),   MODE(2) | PULLUDEN | PULLUP_EN},
+	/* DCAN0 RX */
+	{OFFSET(uart1_rtsn),   MODE(2) | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux dcan1_pin_mux[] = {
+	/* DCAN1 TX */
+	{OFFSET(uart1_rxd),   MODE(2) | PULLUDEN | PULLUP_EN},
+	/* DCAN1 RX */
+	{OFFSET(uart1_txd),   MODE(2) | RXACTIVE},
+	{-1},
+};
+
+static struct module_pin_mux gpios[] = {
+	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS)},
+	/* GPIO0_4  (SPI D1) - TA602 */
+	{OFFSET(spi0_d1), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_5  (SPI CS0) - DISPLAY_ON_OFF */
+	{OFFSET(spi0_cs0), (MODE(7) | PULLUDDIS)},
+	/* GPIO0_7  (PWW0 OUT) - CAN TERM */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_19 (DMA_INTR0) - CLKOUT SYS */
+	{OFFSET(xdma_event_intr0), (MODE(7) | RXACTIVE)},
+	/* GPIO0_20 (DMA_INTR1) - SPI1 nCS1 */
+	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUDEN | PULLUP_EN)},
+	/* GPIO0_30 (GPMC_WAIT0) - TA601 */
+	{OFFSET(gpmc_wait0), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO0_31 (GPMC_nWP) - SW601 PushButton */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO1_28 (GPMC_nWE) - FRAM_nWP */
+	{OFFSET(gpmc_be1n), (MODE(7) | PULLUDDIS)},
+	/* GPIO2_0  (GPMC_nCS3)	- VBAT_OK */
+	{OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/* GPIO2_2  (GPMC_nADV_ALE) - DCOK */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | PULLUDDIS | RXACTIVE)},
+	/* GPIO2_4  (GPMC_nWE) - TST_BAST */
+	{OFFSET(gpmc_wen), (MODE(7) | PULLUDDIS)},
+	/* GPIO3_18 (MCASP0_ACLKR) - SW601 CNTup, mapped to Counter eQEB0A_in */
+	{OFFSET(mcasp0_aclkr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	/* GPIO3_19 (MCASP0_FSR) - SW601 CNTdown, mapped to Counter eQEB0B_in */
+	{OFFSET(mcasp0_fsr), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	/* GPIO3_20 (MCASP0_AXR1) - SW601 CNTdown, map to Counter eQEB0_index */
+	{OFFSET(mcasp0_axr1), (MODE(1) | PULLUDDIS | RXACTIVE)},
+	{-1},
+};
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	/* UART0_CTS */
+	{OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_RXD */
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_TXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+	{-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+	/* I2C_DATA */
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	/* I2C_SCLK */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+
+	{-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+	{OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)},	/* LCD-Data(0) */
+	{OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)},	/* LCD-Data(1) */
+	{OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)},	/* LCD-Data(2) */
+	{OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)},	/* LCD-Data(3) */
+	{OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)},	/* LCD-Data(4) */
+	{OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)},	/* LCD-Data(5) */
+	{OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)},	/* LCD-Data(6) */
+	{OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)},	/* LCD-Data(7) */
+	{OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)},	/* LCD-Data(8) */
+	{OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)},	/* LCD-Data(9) */
+	{OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)},	/* LCD-Data(10) */
+	{OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)},	/* LCD-Data(11) */
+	{OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)},	/* LCD-Data(12) */
+	{OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)},	/* LCD-Data(13) */
+	{OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)},	/* LCD-Data(14) */
+	{OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)},	/* LCD-Data(15) */
+
+	{OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)},	/* LCD-Data(16) */
+	{OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)},	/* LCD-Data(17) */
+	{OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)},	/* LCD-Data(18) */
+	{OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)},	/* LCD-Data(19) */
+	{OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)},	/* LCD-Data(20) */
+	{OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)},	/* LCD-Data(21) */
+	{OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)},	/* LCD-Data(22) */
+	{OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)},	/* LCD-Data(23) */
+
+	{OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)},	/* LCD-VSync */
+	{OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)},	/* LCD-HSync */
+	{OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+	{OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)},	/* LCD-CLK */
+
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(usb0_pin_mux);
+	configure_module_pin_mux(spi1_pin_mux);
+	configure_module_pin_mux(dcan0_pin_mux);
+	configure_module_pin_mux(dcan1_pin_mux);
+	configure_module_pin_mux(mmc1_pin_mux);
+	configure_module_pin_mux(lcd_pin_mux);
+	configure_module_pin_mux(gpios);
+}
--- a/board/BuR/tseries/Makefile
+++ b/board/BuR/tseries/Makefile
@ -0,0 +1,14 @@
+#
+# Makefile
+#
+# Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+# Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD),y)
+obj-y	:= mux.o
+endif
+obj-y	+= ../common/common.o
+obj-y	+= board.o
--- a/board/BuR/tseries/board.c
+++ b/board/BuR/tseries/board.c
@ -0,0 +1,147 @@
+/*
+ * board.c
+ *
+ * Board functions for B&R LEIT Board
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <power/tps65217.h>
+#include "../common/bur_common.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* --------------------------------------------------------------------------*/
+/* -- defines for GPIO -- */
+#define	ETHLED_ORANGE	(96+16)	/* GPIO3_16 */
+#define	REPSWITCH	(0+20)	/* GPIO0_20 */
+
+
+#if defined(CONFIG_SPL_BUILD)
+/* TODO: check ram-timing ! */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+static const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+/*
+ * called from spl_nand.c
+ * return 0 for loading linux, return 1 for loading u-boot
+ */
+int spl_start_uboot(void)
+{
+	if (0 == gpio_get_value(REPSWITCH)) {
+		blink(5, 125, ETHLED_ORANGE);
+		mdelay(1000);
+		printf("SPL: entering u-boot instead kernel image.\n");
+		return 1;
+	}
+	return 0;
+}
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#define OSC	(V_OSCK/1000000)
+static const struct dpll_params dpll_ddr3 = { 400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	pmicsetup(1000);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	return &dpll_ddr3;
+}
+
+void sdram_init(void)
+{
+	config_ddr(400, &ddr3_ioregs,
+		   &ddr3_data,
+		   &ddr3_cmd_ctrl_data,
+		   &ddr3_emif_reg_data, 0);
+}
+#endif /* CONFIG_SPL_BUILD */
+
+/* Basic board specific setup.  Pinmux has been handled already. */
+int board_init(void)
+{
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	gpio_direction_output(ETHLED_ORANGE, 0);
+
+	if (0 == gpio_get_value(REPSWITCH)) {
+		printf("\n\n\n"
+		"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n"
+		"!!!!!!! recovery switch activated !!!!!!!\n"
+		"!!!!!!!     running usbupdate     !!!!!!!\n"
+		"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!\n\n\n");
+		setenv("bootcmd", "sleep 2; run netupdate;");
+	}
+
+	printf("turning on display power+backlight ... ");
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL1,
+			   0x09, TPS65217_MASK_ALL_BITS);	/* 200 Hz, ON */
+	tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_WLEDCTRL2,
+			   0x62, TPS65217_MASK_ALL_BITS);	/* 100% */
+	printf("ok.\n");
+
+	return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
--- a/board/BuR/tseries/mux.c
+++ b/board/BuR/tseries/mux.c
@ -0,0 +1,225 @@
+/*
+ * mux.c
+ *
+ * Pinmux Setting for B&R LEIT Board(s)
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at>
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	/* UART0_CTS */
+	{OFFSET(uart0_ctsn), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_RXD */
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* UART0_TXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},
+	{-1},
+};
+#ifdef CONFIG_MMC
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */
+	{-1},
+};
+#endif
+static struct module_pin_mux i2c0_pin_mux[] = {
+	/* I2C_DATA */
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	/* I2C_SCLK */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
+	{-1},
+};
+
+static struct module_pin_mux spi0_pin_mux[] = {
+	/* SPI0_SCLK */
+	{OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	/* SPI0_D0 */
+	{OFFSET(spi0_d0), (MODE(0) | RXACTIVE |	PULLUDEN | PULLUP_EN)},
+	/* SPI0_D1 */
+	{OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	/* SPI0_CS0 */
+	{OFFSET(spi0_cs0), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN)},
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+static struct module_pin_mux mii2_pin_mux[] = {
+	{OFFSET(gpmc_a0), MODE(1)},		/* MII2_TXEN */
+	{OFFSET(gpmc_a1), MODE(1) | RXACTIVE},	/* MII2_RXDV */
+	{OFFSET(gpmc_a2), MODE(1)},		/* MII2_TXD3 */
+	{OFFSET(gpmc_a3), MODE(1)},		/* MII2_TXD2 */
+	{OFFSET(gpmc_a4), MODE(1)},		/* MII2_TXD1 */
+	{OFFSET(gpmc_a5), MODE(1)},		/* MII2_TXD0 */
+	{OFFSET(gpmc_a6), MODE(1) | RXACTIVE},	/* MII2_TXCLK */
+	{OFFSET(gpmc_a7), MODE(1) | RXACTIVE},	/* MII2_RXCLK */
+	{OFFSET(gpmc_a8), MODE(1) | RXACTIVE},	/* MII2_RXD3 */
+	{OFFSET(gpmc_a9), MODE(1) | RXACTIVE},	/* MII2_RXD2 */
+	{OFFSET(gpmc_a10), MODE(1) | RXACTIVE},	/* MII2_RXD1 */
+	{OFFSET(gpmc_a11), MODE(1) | RXACTIVE},	/* MII2_RXD0 */
+	{OFFSET(gpmc_wpn), (MODE(1) | RXACTIVE)},/* MII2_RXERR */
+						/*
+						 * MII2_CRS is shared with
+						 * NAND_WAIT0
+						 */
+	{OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */
+	{-1},
+};
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)},	/* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+#endif
+static struct module_pin_mux gpIOs[] = {
+	/* GPIO0_6  (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */
+	{OFFSET(spi0_cs1),  (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* TIMER5   (MMC0_DAT3) - TIMER5 (Buzzer) */
+	{OFFSET(mmc0_dat3), (MODE(3) | PULLUDEN | RXACTIVE)},
+	/* TIMER6   (MMC0_DAT2) - PWM_BACK_3V3, later used as MODE3 for PWM */
+	{OFFSET(mmc0_dat2), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_28 (MMC0_DAT1)	 - MII_nNAND */
+	{OFFSET(mmc0_dat1), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_29 (MMC0_DAT0)	 - NAND_1n0 */
+	{OFFSET(mmc0_dat0), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO2_30 (MMC0_CLK) - nRESET (PHY) */
+	{OFFSET(mmc0_clk), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_18 (MCASP0_ACLKR) - CPLD JTAG TDI */
+	{OFFSET(mcasp0_aclkr), (MODE(7) | PULLUDEN | PULLUP_EN  | RXACTIVE)},
+	/* GPIO3_19 (MCASP0_FSR) - CPLD JTAG TMS */
+	{OFFSET(mcasp0_fsr), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_20 (MCASP0_AXR1) - CPLD JTAG TCK */
+	{OFFSET(mcasp0_axr1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_21 (MCASP0_AHCLKX) - CPLD JTAG TDO */
+	{OFFSET(mcasp0_ahclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO2_0  (GPMC_nCS3) - DCOK */
+	{OFFSET(gpmc_csn3), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/* GPIO0_29 (RMII1_REFCLK) - eMMC nRST */
+	{OFFSET(rmii1_refclk), (MODE(7) | PULLUDDIS | RXACTIVE) },
+	/*
+	 * GPIO0_7 (PWW0 OUT)
+	 * DISPLAY_ONOFF (Backlight Enable at LVDS Versions)
+	 */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN | RXACTIVE)},
+	/* GPIO0_19 (DMA_INTR0) - ISPLAY_MODE (CPLD) */
+	{OFFSET(xdma_event_intr0), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},
+	/* GPIO0_20 (DMA_INTR1) - REP-Switch */
+	{OFFSET(xdma_event_intr1), (MODE(7) | PULLUP_EN | RXACTIVE)},
+	/* GPIO3_14 (MCASP0_ACLKX) - frei / PP709 */
+	{OFFSET(mcasp0_aclkx), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+	/* GPIO3_15 (MCASP0_FSX) - PMIC_nRESET */
+	{OFFSET(mcasp0_fsx),   (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE) },
+	/* GPIO3_16 (MCASP0_AXR0) - ETH1_LEDY */
+	{OFFSET(mcasp0_axr0),  (MODE(7) | PULLUDDIS) },
+	/* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */
+	{OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) },
+
+	{-1},
+};
+
+static struct module_pin_mux lcd_pin_mux[] = {
+	{OFFSET(lcd_data0), (MODE(0) | PULLUDDIS)},	/* LCD-Data(0) */
+	{OFFSET(lcd_data1), (MODE(0) | PULLUDDIS)},	/* LCD-Data(1) */
+	{OFFSET(lcd_data2), (MODE(0) | PULLUDDIS)},	/* LCD-Data(2) */
+	{OFFSET(lcd_data3), (MODE(0) | PULLUDDIS)},	/* LCD-Data(3) */
+	{OFFSET(lcd_data4), (MODE(0) | PULLUDDIS)},	/* LCD-Data(4) */
+	{OFFSET(lcd_data5), (MODE(0) | PULLUDDIS)},	/* LCD-Data(5) */
+	{OFFSET(lcd_data6), (MODE(0) | PULLUDDIS)},	/* LCD-Data(6) */
+	{OFFSET(lcd_data7), (MODE(0) | PULLUDDIS)},	/* LCD-Data(7) */
+	{OFFSET(lcd_data8), (MODE(0) | PULLUDDIS)},	/* LCD-Data(8) */
+	{OFFSET(lcd_data9), (MODE(0) | PULLUDDIS)},	/* LCD-Data(9) */
+	{OFFSET(lcd_data10), (MODE(0) | PULLUDDIS)},	/* LCD-Data(10) */
+	{OFFSET(lcd_data11), (MODE(0) | PULLUDDIS)},	/* LCD-Data(11) */
+	{OFFSET(lcd_data12), (MODE(0) | PULLUDDIS)},	/* LCD-Data(12) */
+	{OFFSET(lcd_data13), (MODE(0) | PULLUDDIS)},	/* LCD-Data(13) */
+	{OFFSET(lcd_data14), (MODE(0) | PULLUDDIS)},	/* LCD-Data(14) */
+	{OFFSET(lcd_data15), (MODE(0) | PULLUDDIS)},	/* LCD-Data(15) */
+
+	{OFFSET(gpmc_ad8), (MODE(1) | PULLUDDIS)},	/* LCD-Data(16) */
+	{OFFSET(gpmc_ad9), (MODE(1) | PULLUDDIS)},	/* LCD-Data(17) */
+	{OFFSET(gpmc_ad10), (MODE(1) | PULLUDDIS)},	/* LCD-Data(18) */
+	{OFFSET(gpmc_ad11), (MODE(1) | PULLUDDIS)},	/* LCD-Data(19) */
+	{OFFSET(gpmc_ad12), (MODE(1) | PULLUDDIS)},	/* LCD-Data(20) */
+	{OFFSET(gpmc_ad13), (MODE(1) | PULLUDDIS)},	/* LCD-Data(21) */
+	{OFFSET(gpmc_ad14), (MODE(1) | PULLUDDIS)},	/* LCD-Data(22) */
+	{OFFSET(gpmc_ad15), (MODE(1) | PULLUDDIS)},	/* LCD-Data(23) */
+
+	{OFFSET(lcd_vsync), (MODE(0) | PULLUDDIS)},	/* LCD-VSync */
+	{OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)},	/* LCD-HSync */
+	{OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */
+	{OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)},	/* LCD-CLK */
+
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(mii2_pin_mux);
+#ifdef CONFIG_NAND
+	configure_module_pin_mux(nand_pin_mux);
+#elif defined(CONFIG_MMC)
+	configure_module_pin_mux(mmc1_pin_mux);
+#endif
+	configure_module_pin_mux(spi0_pin_mux);
+	configure_module_pin_mux(lcd_pin_mux);
+	configure_module_pin_mux(gpIOs);
+}
--- a/board/htkw/mcx/mcx.h
+++ b/board/htkw/mcx/mcx.h
@ -325,8 +325,6 @@ const omap3_sysinfo sysinfo = {
 	MUX_VAL(CP(SYS_32K),		(IEN  | PTD | EN  | M4)) \
 	MUX_VAL(CP(SYS_CLKREQ),		(IEN  | PTD | DIS | M0)) \
 	MUX_VAL(CP(SYS_NIRQ),		(IEN  | PTD | EN  | M4)) \
-	MUX_VAL(CP(SYS_NRESWARM),	(IEN | PTU | DIS | M4)) \
-					/* SYS_nRESWARM */\
 	MUX_VAL(CP(SYS_BOOT0),		(IEN  | PTD | DIS | M4)) \
 	MUX_VAL(CP(SYS_BOOT1),		(IEN  | PTD | DIS | M4)) \
 	MUX_VAL(CP(SYS_BOOT2),		(IEN  | PTD | DIS | M4)) \
--- a/board/silica/pengwyn/Makefile
+++ b/board/silica/pengwyn/Makefile
@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_NOR_BOOT),y)
+obj-y	:= mux.o
+endif
+
+obj-y	+= board.o
--- a/board/silica/pengwyn/board.c
+++ b/board/silica/pengwyn/board.c
@ -0,0 +1,207 @@
+/*
+ * board.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+#include <phy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#if defined(CONFIG_SPL_BUILD)
+
+/* DDR3 RAM timings */
+static const struct ddr_data ddr3_data = {
+	.datardsratio0 = MT41K128MJT187E_RD_DQS,
+	.datawdsratio0 = MT41K128MJT187E_WR_DQS,
+	.datafwsratio0 = MT41K128MJT187E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K128MJT187E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+	.cmd0csratio = MT41K128MJT187E_RATIO,
+	.cmd0iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+	.cmd1csratio = MT41K128MJT187E_RATIO,
+	.cmd1iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+	.cmd2csratio = MT41K128MJT187E_RATIO,
+	.cmd2iclkout = MT41K128MJT187E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K128MJT187E_EMIF_SDCFG,
+	.ref_ctrl = MT41K128MJT187E_EMIF_SDREF,
+	.sdram_tim1 = MT41K128MJT187E_EMIF_TIM1,
+	.sdram_tim2 = MT41K128MJT187E_EMIF_TIM2,
+	.sdram_tim3 = MT41K128MJT187E_EMIF_TIM3,
+	.zq_config = MT41K128MJT187E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K128MJT187E_EMIF_READ_LATENCY |
+				PHY_EN_DYN_PWRDN,
+};
+
+const struct ctrl_ioregs ddr3_ioregs = {
+	.cm0ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.cm1ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.cm2ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.dt0ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+	.dt1ioctl		= MT41K128MJT187E_IOCTRL_VALUE,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	/* break into full u-boot on 'c' */
+	return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr_266 = {
+		266, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_303 = {
+		303, OSC-1, 1, -1, -1, -1, -1};
+const struct dpll_params dpll_ddr_400 = {
+		400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	/*
+	 * The pengwyn board uses the TPS650250 PMIC  without I2C
+	 * interface and will output the following fixed voltages:
+	 * DCDC1=3V3 (IO) DCDC2=1V5 (DDR) DCDC3=1V26 (Vmpu)
+	 * VLDO1=1V8 (IO) VLDO2=1V8(IO)
+	 * Vcore=1V1 is fixed, generated by TPS62231
+	 */
+
+	/* Get the frequency */
+	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* 720MHz cpu, this might change on newer board revisions */
+	dpll_mpu_opp100.m = MPUPLL_M_720;
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	/* future configs can return other clock settings */
+	return &dpll_ddr_303;
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+void sdram_init(void)
+{
+	config_ddr(303, &ddr3_ioregs, &ddr3_data,
+		   &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#endif /* if CONFIG_SPL_BUILD */
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	gpmc_init();
+	return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_id		= 0,
+		.phy_if		= PHY_INTERFACE_MODE_MII,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_id		= 1,
+		.phy_if		= PHY_INTERFACE_MODE_MII,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+
+int board_eth_init(bd_t *bis)
+{
+	int rv, n = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		printf("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			return n;
+	}
+
+	writel(MII_MODE_ENABLE, &cdev->miisel);
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		n += rv;
+	return n;
+}
+#endif /* if CONFIG_DRIVER_TI_CPSW */
--- a/board/silica/pengwyn/board.h
+++ b/board/silica/pengwyn/board.h
@ -0,0 +1,15 @@
+/*
+ * board.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_board_pin_mux(void);
+
+#endif
--- a/board/silica/pengwyn/mux.c
+++ b/board/silica/pengwyn/mux.c
@ -0,0 +1,98 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+/* UART0 pins E15(rx),E16(tx) [E17(rts),E18(cts)] */
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+/* unused: UART1 pins D15(tx),D16(rx),D17(cts),D18(rts) */
+
+/* I2C pins C16(scl)/C17(sda) */
+static struct module_pin_mux i2c0_pin_mux[] = {
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+					PULLUDEN | SLEWCTRL)}, /* I2C0_DATA */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+					PULLUDEN | SLEWCTRL)}, /* I2C0_SCLK */
+	{-1},
+};
+
+/* MMC0 pins */
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},  /* MMC0_CMD */
+	{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)},  /* MMC0_CD */
+	{-1},
+};
+
+/* MII pins */
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+/* NAND pins */
+static struct module_pin_mux nand_pin_mux[] = {
+	{OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD0 */
+	{OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD1 */
+	{OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD2 */
+	{OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD3 */
+	{OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD4 */
+	{OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD5 */
+	{OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD6 */
+	{OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* NAND AD7 */
+	{OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+	{OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)},	/* NAND_WPN */
+	{OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)},	/* NAND_CS0 */
+	{OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+	{OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)},	/* NAND_OE */
+	{OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)},	/* NAND_WEN */
+	{OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)},	/* NAND_BE_CLE */
+	{-1},
+};
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(uart0_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(mmc0_pin_mux);
+	configure_module_pin_mux(nand_pin_mux);
+}
--- a/board/ti/am43xx/board.c
+++ b/board/ti/am43xx/board.c
@ -346,14 +346,14 @@ static void enable_vtt_regulator(void)
 	u32 temp;

 	/* enable module */
-	writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO0_BASE + OMAP_GPIO_CTRL);
-
-	/* enable output for GPIO0_22 */
-	writel(GPIO_SETDATAOUT(GPIO_22),
-	       AM33XX_GPIO0_BASE + OMAP_GPIO_SETDATAOUT);
-	temp = readl(AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
-	temp = temp & ~(GPIO_OE_ENABLE(GPIO_22));
-	writel(temp, AM33XX_GPIO0_BASE + OMAP_GPIO_OE);
+	writel(GPIO_CTRL_ENABLEMODULE, AM33XX_GPIO5_BASE + OMAP_GPIO_CTRL);
+
+	/* enable output for GPIO5_7 */
+	writel(GPIO_SETDATAOUT(7),
+	       AM33XX_GPIO5_BASE + OMAP_GPIO_SETDATAOUT);
+	temp = readl(AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
+	temp = temp & ~(GPIO_OE_ENABLE(7));
+	writel(temp, AM33XX_GPIO5_BASE + OMAP_GPIO_OE);
 }

 void sdram_init(void)
--- a/board/ti/am43xx/mux.c
+++ b/board/ti/am43xx/mux.c
@ -33,8 +33,8 @@ static struct module_pin_mux i2c0_pin_mux[] = {
 	{-1},
 };

-static struct module_pin_mux gpio0_22_pin_mux[] = {
-	{OFFSET(ddr_ba2), (MODE(9) | PULLUP_EN)},	/* GPIO0_22 */
+static struct module_pin_mux gpio5_7_pin_mux[] = {
+	{OFFSET(spi0_cs0), (MODE(7) | PULLUP_EN)},	/* GPIO5_7 */
 	{-1},
 };

@ -49,7 +49,7 @@ void enable_board_pin_mux(void)
 	configure_module_pin_mux(i2c0_pin_mux);

 	if (board_is_gpevm())
-		configure_module_pin_mux(gpio0_22_pin_mux);
+		configure_module_pin_mux(gpio5_7_pin_mux);
 }

 void enable_i2c0_pin_mux(void)
--- a/boards.cfg
+++ b/boards.cfg
@ -256,6 +256,11 @@ Active  arm         armv7          am33xx      phytec          pcm051
 Active  arm         armv7          am33xx      siemens         dxr2                dxr2                                 -                                                                                                                                 Roger Meier <r.meier@siemens.com>
 Active  arm         armv7          am33xx      siemens         pxm2                pxm2                                 -                                                                                                                                 Roger Meier <r.meier@siemens.com>
 Active  arm         armv7          am33xx      siemens         rut                 rut                                  -                                                                                                                                 Roger Meier <r.meier@siemens.com>
+Active  arm         armv7          am33xx      silica          pengwyn             pengwyn                              -                                                                                                                                 Lothar Felten <lothar.felten@gmail.com>
+Active  arm         armv7          am33xx      BuR             tseries             tseries_nand                         tseries:SERIAL1,CONS_INDEX=1,NAND                                                                                             Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active  arm         armv7          am33xx      BuR             tseries             tseries_mmc                          tseries:SERIAL1,CONS_INDEX=1,EMMC_BOOT                                                                                        Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active  arm         armv7          am33xx      BuR             tseries             tseries_spi                          tseries:SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT                                                                               Hannes Petermaier <hannes.petermaier@br-automation.com>
+Active  arm         armv7          am33xx      BuR             kwb                 kwb                                  kwb:SERIAL1,CONS_INDEX=1                                                                                                          Hannes Petermaier <hannes.petermaier@br-automation.com>
 Active  arm         armv7          am33xx      ti              am335x              am335x_boneblack                     am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT                                                                                         Tom Rini <trini@ti.com>
 Active  arm         armv7          am33xx      ti              am335x              am335x_evm                           am335x_evm:SERIAL1,CONS_INDEX=1,NAND                                                                                              Tom Rini <trini@ti.com>
 Active  arm         armv7          am33xx      ti              am335x              am335x_evm_nor                       am335x_evm:SERIAL1,CONS_INDEX=1,NAND,NOR                                                                                          Tom Rini <trini@ti.com>
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@ -20,6 +20,7 @@

 #define MACH_TYPE_TIAM335EVM		3589	/* Until the next sync */
 #define CONFIG_MACH_TYPE		MACH_TYPE_TIAM335EVM
+#define CONFIG_BOARD_LATE_INIT

 /* Clock Defines */
 #define V_OSCK				24000000  /* Clock output from T2 */
@ -31,6 +32,12 @@
 /* Always 128 KiB env size */
 #define CONFIG_ENV_SIZE			(128 << 10)

+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
 #ifdef CONFIG_NAND
 #define NANDARGS \
 	"mtdids=" MTDIDS_DEFAULT "\0" \
@ -64,6 +71,9 @@
 	"bootfile=zImage\0" \
 	"fdtfile=undefined\0" \
 	"console=ttyO0,115200n8\0" \
+	"partitions=" \
+		"uuid_disk=${uuid_gpt_disk};" \
+		"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
 	"optargs=\0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 ro\0" \
@ -295,6 +305,9 @@
 #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT)
 /* disable host part of MUSB in SPL */
 #undef CONFIG_MUSB_HOST
+/* disable EFI partitions and partition UUID support */
+#undef CONFIG_PARTITION_UUIDS
+#undef CONFIG_EFI_PARTITION
 /*
 * Disable CPSW SPL support so we fit within the 101KiB limit.
 */
--- a/include/configs/am43xx_evm.h
+++ b/include/configs/am43xx_evm.h
@ -84,6 +84,12 @@
 #define CONFIG_OMAP_USB_PHY
 #define CONFIG_AM437X_USB2PHY2_HOST

+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x80200000\0" \
@ -95,6 +101,9 @@
 	"bootdir=/boot\0" \
 	"bootfile=zImage\0" \
 	"console=ttyO0,115200n8\0" \
+	"partitions=" \
+		"uuid_disk=${uuid_gpt_disk};" \
+		"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \
 	"optargs=\0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
--- a/include/configs/bur_am335x_common.h
+++ b/include/configs/bur_am335x_common.h
@ -0,0 +1,197 @@
+/*
+ * bur_am335x_common.h
+ *
+ * common parts used by B&R AM335x based boards
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:        GPL-2.0+
+ */
+
+#ifndef __BUR_AM335X_COMMON_H__
+#define __BUR_AM335X_COMMON_H__
+/* ------------------------------------------------------------------------- */
+#define CONFIG_AM33XX
+#define CONFIG_OMAP
+#define CONFIG_OMAP_COMMON
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_SYS_CACHELINE_SIZE	64
+#define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
+
+/* Timer information */
+#define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
+#define CONFIG_SYS_TIMERBASE		0x48040000	/* Use Timer2 */
+
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_POWER_TPS65217
+
+#define CONFIG_SYS_NO_FLASH		/* have no NOR-flash */
+
+#include <asm/arch/omap.h>
+
+/* NS16550 Configuration */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		48000000
+#define CONFIG_SYS_NS16550_COM1		0x44e09000	/* UART0 */
+#define CONFIG_BAUDRATE			115200
+
+/* Network defines */
+#define CONFIG_CMD_NET			/* 'bootp' and 'tftp' */
+#define CONFIG_CMD_DHCP
+#define CONFIG_BOOTP_DNS		/* Configurable parts of CMD_DHCP */
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT		4
+#define CONFIG_CMD_PING
+#define CONFIG_DRIVER_TI_CPSW		/* Driver for IP block */
+#define CONFIG_MII			/* Required in net/eth.c */
+#define CONFIG_SPL_ETH_SUPPORT
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			1
+#define CONFIG_PHY_NATSEMI
+#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT		/* used for a fetching MAC-Address */
+#define CONFIG_SPL_NET_VCI_STRING	"AM335x U-Boot SPL"
+
+/*
+ * SPL related defines.  The Public RAM memory map the ROM defines the
+ * area between 0x402F0400 and 0x4030B800 as a download area and
+ * 0x4030B800 to 0x4030CE00 as a public stack area.  The ROM also
+ * supports X-MODEM loading via UART, and we leverage this and then use
+ * Y-MODEM to load u-boot.img, when booted over UART.
+ */
+#define CONFIG_SPL_TEXT_BASE		0x402F0400
+#define CONFIG_SPL_MAX_SIZE		(0x4030B800 - CONFIG_SPL_TEXT_BASE)
+
+/*
+ * Since SPL did pll and ddr initialization for us,
+ * we don't need to do it twice.
+ */
+#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT)
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif /* !CONFIG_SPL_BUILD, ... */
+/*
+ * Our DDR memory always starts at 0x80000000 and U-Boot shall have
+ * relocated itself to higher in memory by the time this value is used.
+ */
+#define CONFIG_SYS_LOAD_ADDR		0x80000000
+/*
+ * ----------------------------------------------------------------------------
+ * DDR information.  We say (for simplicity) that we have 1 bank,
+ * always, even when we have more.  We always start at 0x80000000,
+ * and we place the initial stack pointer in our SRAM.
+ */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+#define CONFIG_SYS_INIT_SP_ADDR		(NON_SECURE_SRAM_END - \
+					GENERATED_GBL_DATA_SIZE)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP24XX
+
+/* GPIO */
+#define CONFIG_OMAP_GPIO
+#define CONFIG_CMD_GPIO
+/*
+ * ----------------------------------------------------------------------------
+ * The following are general good-enough settings for U-Boot.  We set a
+ * large malloc pool as we generally have a lot of DDR, and we opt for
+ * function over binary size in the main portion of U-Boot as this is
+ * generally easily constrained later if needed.  We enable the config
+ * options that give us information in the environment about what board
+ * we are on so we do not need to rely on the command prompt.  We set a
+ * console baudrate of 115200 and use the default baud rate table.
+ */
+#define CONFIG_SYS_MALLOC_LEN		(1024 << 10)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT		"U-Boot (BuR V2.0)# "
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_ENV_OVERWRITE		/* Overwrite ethaddr / serial# */
+
+/* As stated above, the following choices are optional. */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+
+/* We set the max number of command args high to avoid HUSH bugs. */
+#define CONFIG_SYS_MAXARGS		64
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE		512
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE +\
+					sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/*
+ * For commands to use, we take the default list and add a few other
+ * useful commands.  Note that we must have set CONFIG_SYS_NO_FLASH
+ * prior to this include, in order to skip a few commands.  When we do
+ * have flash, if we expect these commands they must be enabled in that
+ * config.  If desired, a specific list of desired commands can be used
+ * instead.
+ */
+#include <config_cmd_default.h>
+/* undefine commands, which we do not need */
+#undef CONFIG_CMD_EDITENV
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IMI
+#undef CONFIG_CMD_ITEST
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_NFS
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_XIMG
+#undef CONFIG_CMD_CRC32
+/* define command we need always */
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_SOURCE
+
+/*
+ * Our platforms make use of SPL to initalize the hardware (primarily
+ * memory) enough for full U-Boot to be loaded.  We also support Falcon
+ * Mode so that the Linux kernel can be booted directly from SPL
+ * instead, if desired.  We make use of the general SPL framework found
+ * under common/spl/.  Given our generally common memory map, we set a
+ * number of related defaults and sizes here.
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+/*
+ * Place the image at the start of the ROM defined image space.
+ * We limit our size to the ROM-defined downloaded image area, and use the
+ * rest of the space for stack.  We load U-Boot itself into memory at
+ * 0x80800000 for legacy reasons (to not conflict with older SPLs).  We
+ * have our BSS be placed 1MiB after this, to allow for the default
+ * Linux kernel address of 0x80008000 to work, in the Falcon Mode case.
+ * We have the SPL malloc pool at the end of the BSS area.
+ *
+ * ----------------------------------------------------------------------------
+ */
+#define CONFIG_SPL_STACK		CONFIG_SYS_INIT_SP_ADDR
+#undef  CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0x80800000
+#define CONFIG_SPL_BSS_START_ADDR	0x80A00000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
+#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SPL_BSS_START_ADDR + \
+					CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE	CONFIG_SYS_MALLOC_LEN
+
+/* General parts of the framework, required. */
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_YMODEM_SUPPORT
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#endif	/* ! __BUR_AM335X_COMMON_H__ */
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@ -45,13 +45,6 @@
 #define CONFIG_MISC_INIT_R

 #define CONFIG_OF_LIBFDT		1
-/*
- * The early kernel mapping on ARM currently only maps from the base of DRAM
- * to the end of the kernel image.  The kernel is loaded at DRAM base + 0x8000.
- * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000,
- * so that leaves DRAM base to DRAM base + 0x4000 available.
- */
-#define CONFIG_SYS_BOOTMAPSZ	        0x4000

 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@ -34,8 +34,19 @@

 #define CONFIG_SYS_OMAP_ABE_SYSCK

+/* Define the default GPT table for eMMC */
+#define PARTS_DEFAULT \
+	"uuid_disk=${uuid_gpt_disk};" \
+	"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
+
 #include <configs/ti_omap5_common.h>

+/* Enhance our eMMC support / experience. */
+#define CONFIG_CMD_GPT
+#define CONFIG_EFI_PARTITION
+#define CONFIG_PARTITION_UUIDS
+#define CONFIG_CMD_PART
+
 /* CPSW Ethernet */
 #define CONFIG_CMD_NET			/* 'bootp' and 'tftp' */
 #define CONFIG_CMD_DHCP
--- a/include/configs/kwb.h
+++ b/include/configs/kwb.h
@ -0,0 +1,128 @@
+/*
+ * kwb.h
+ *
+ * specific parts for B&R KWB Motherboard
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:        GPL-2.0+
+ */
+
+#ifndef __CONFIG_KWB_H__
+#define __CONFIG_KWB_H__
+
+#include <configs/bur_am335x_common.h>
+/* ------------------------------------------------------------------------- */
+/* Clock Defines */
+#define V_OSCK				26000000  /* Clock output from T2 */
+#define V_SCLK				(V_OSCK)
+
+#define CONFIG_POWER_TPS65217
+
+#define CONFIG_MACH_TYPE		3589
+/* I2C IP block */
+#define CONFIG_SYS_OMAP24_I2C_SPEED_PSOC	20000
+
+/* GPIO */
+#define CONFIG_SPL_GPIO_SUPPORT
+
+/* MMC/SD IP block */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_CMD_MMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+/* RAW SD card / eMMC locations. */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /*addr. 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS		0x200 /* 256 KB */
+#define CONFIG_SPL_MMC_SUPPORT
+
+#undef CONFIG_SPL_OS_BOOT
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_SYS_SPL_ARGS_ADDR		0x80F80000
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0x900	/* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0x80	/* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0x80	/* 64KiB */
+
+#endif /* CONFIG_SPL_OS_BOOT */
+
+/* Always 128 KiB env size */
+#define CONFIG_ENV_SIZE			(128 << 10)
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"autoload=0\0" \
+	"loadaddr=0x80100000\0" \
+	"bootfile=arimg\0" \
+	"usbboot=echo Booting from USB-Stick ...; " \
+		"usb start; " \
+		"fatload usb 0 ${loadaddr} ${bootfile}; " \
+		"usb stop; " \
+		"go ${loadaddr};\0" \
+	"netboot=echo Booting from network ...; " \
+		"setenv autoload 0; " \
+		"dhcp; " \
+		"tftp ${loadaddr} arimg; " \
+		"go ${loadaddr}\0" \
+	"usbupdate=echo Updating UBOOT from USB-Stick ...; " \
+		"usb start; " \
+		"fatload usb 0 0x80000000 updateubootusb.img; " \
+		"source;\0" \
+	"netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
+		"setenv autoload 0; " \
+		"dhcp;" \
+		"tftp 0x80000000 updateUBOOT.img;" \
+		"source;\0"
+#endif /* !CONFIG_SPL_BUILD*/
+
+#define CONFIG_BOOTCOMMAND \
+	"run usbupdate;"
+#define CONFIG_BOOTDELAY		1 /* TODO: für release auf 0 setzen */
+
+/* undefine command which we not need here */
+#undef	CONFIG_BOOTM_LINUX
+#undef	CONFIG_BOOTM_NETBSD
+#undef	CONFIG_BOOTM_PLAN9
+#undef	CONFIG_BOOTM_RTEMS
+#undef	CONFIG_GZIP
+#undef	CONFIG_ZLIB
+#undef CONFIG_CMD_CRC32
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+/* attention! not only for gadget, enables also highspeed in hostmode */
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE	MUSB_HOST
+
+#ifdef CONFIG_MUSB_HOST
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif /* CONFIG_MUSB_HOST */
+
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		1
+#define CONFIG_SYS_MMC_ENV_PART		2
+#define CONFIG_ENV_OFFSET		0x40000	/* TODO: Adresse definieren */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+/*
+ * Common filesystems support.  When we have removable storage we
+ * enabled a number of useful commands and support.
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_CMD_FS_GENERIC
+#endif /* CONFIG_MMC, ... */
+
+#endif	/* ! __CONFIG_TSERIES_H__ */
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@ -98,6 +98,7 @@

 /* EHCI */
 #define CONFIG_USB_STORAGE
+#define CONFIG_OMAP3_GPIO_2
 #define CONFIG_OMAP3_GPIO_5
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_OMAP
@ -263,10 +264,9 @@
 			"${mtdparts} "					\
 			"vram=6M omapfb.vram=1:2M,2:2M,3:2M "		\
 			"omapdss.def_disp=lcd;"				\
-		"bootm 0x82000000 0x84000000\0"
-
-#define CONFIG_BOOTCOMMAND \
-	"run nandboot"
+		"bootm 0x82000000 0x84000000\0"				\
+	"bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;"	\
+		"then source 82000000;else run nandboot;fi\0"

 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
@ -395,6 +395,7 @@
 #define CONFIG_SYS_NAND_ECCSIZE		256
 #define CONFIG_SYS_NAND_ECCBYTES	3
 #define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_SW
+#define CONFIG_SPL_NAND_SOFTECC

 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE

--- a/include/configs/pengwyn.h
+++ b/include/configs/pengwyn.h
@ -0,0 +1,208 @@
+/*
+ * pengwyn.h
+ *
+ * Copyright (C) 2013 Lothar Felten <lothar.felten@gmail.com>
+ *
+ * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_PENGWYN_H
+#define __CONFIG_PENGWYN_H
+
+#define CONFIG_NAND
+#define CONFIG_SERIAL1
+#define CONFIG_CONS_INDEX		1
+
+#include <configs/ti_am335x_common.h>
+
+/* Clock Defines */
+#define V_OSCK				24000000
+#define V_SCLK				V_OSCK
+
+/* set env size */
+#define CONFIG_ENV_SIZE			0x4000
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"loadaddr=0x80200000\0" \
+	"fdtaddr=0x80F80000\0" \
+	"bootpart=0:2\0" \
+	"bootdir=/boot\0" \
+	"bootfile=zImage\0" \
+	"fdtfile=am335x-pengwyn.dtb\0" \
+	"console=ttyO0,115200n8\0" \
+	"optargs=\0" \
+	"mmcdev=0\0" \
+	"mmcroot=/dev/mmcblk0p2 ro\0" \
+	"mmcrootfstype=ext4 rootwait\0" \
+	"rootpath=/export/rootfs\0" \
+	"nfsopts=nolock\0" \
+	"static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
+		"::off\0" \
+	"mmcargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${mmcroot} " \
+		"rootfstype=${mmcrootfstype}\0" \
+	"netargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=/dev/nfs " \
+		"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+		"ip=dhcp\0" \
+	"bootenv=uEnv.txt\0" \
+	"loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
+	"importbootenv=echo Importing environment from mmc ...; " \
+		"env import -t $loadaddr $filesize\0" \
+	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+	"mmcloados=run mmcargs; " \
+		"bootz ${loadaddr} - ${fdtaddr};\0" \
+	"mmcboot=mmc dev ${mmcdev}; " \
+		"if mmc rescan; then " \
+			"echo SD/MMC found on device ${mmcdev};" \
+			"if run loadbootenv; then " \
+				"echo Loaded environment from ${bootenv};" \
+				"run importbootenv;" \
+			"fi;" \
+			"if test -n $uenvcmd; then " \
+				"echo Running uenvcmd ...;" \
+				"run uenvcmd;" \
+			"fi;" \
+			"if run loadimage; then " \
+				"run loadfdt;" \
+				"run mmcloados;" \
+			"fi;" \
+		"fi;\0" \
+	"netboot=echo Booting from network ...; " \
+		"setenv autoload no; " \
+		"dhcp; " \
+		"tftp ${loadaddr} ${bootfile}; " \
+		"tftp ${fdtaddr} ${fdtfile}; " \
+		"run netargs; " \
+		"bootz ${loadaddr} - ${fdtaddr}\0" \
+	"mtdids=" MTDIDS_DEFAULT "\0" \
+	"mtdparts=" MTDPARTS_DEFAULT "\0" \
+	"nandargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${nandroot} " \
+		"rootfstype=${nandrootfstype}\0" \
+	"nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \
+	"nandrootfstype=ubifs rootwait=1\0" \
+	"nandboot=echo Booting from nand ...; " \
+		"run nandargs; " \
+		"nand read ${fdtaddr} u-boot-spl-os; " \
+		"nand read ${loadaddr} kernel; " \
+		"bootz ${loadaddr} - ${fdtaddr}\0"
+#endif
+
+#define CONFIG_BOOTCOMMAND \
+	"run mmcboot;" \
+	"run nandboot;"
+
+/* NS16550 Configuration: primary UART via FDTI */
+#define CONFIG_SYS_NS16550_COM1		0x44e09000
+#define CONFIG_BAUDRATE			115200
+
+/* I2C Configuration */
+#define	CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_CMD_EEPROM
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+
+/* SPL */
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_YMODEM_SUPPORT
+
+/* General network SPL */
+#define CONFIG_SPL_NET_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_NET_VCI_STRING	"AM335x U-Boot SPL"
+
+/* NAND support */
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
+					 CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS		{ 2, 3, 4, 5, 6, 7, 8, 9, \
+					 10, 11, 12, 13, 14, 15, 16, 17, \
+					 18, 19, 20, 21, 22, 23, 24, 25, \
+					 26, 27, 28, 29, 30, 31, 32, 33, \
+					 34, 35, 36, 37, 38, 39, 40, 41, \
+					 42, 43, 44, 45, 46, 47, 48, 49, \
+					 50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	14
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+#define GPMC_NAND_ECC_LP_x8_LAYOUT	1
+#define MTDIDS_DEFAULT			"nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT		"mtdparts=omap2-nand.0:128k(SPL)," \
+					"128k(SPL.backup1)," \
+					"128k(SPL.backup2)," \
+					"128k(SPL.backup3),1792k(u-boot)," \
+					"128k(u-boot-spl-os)," \
+					"128k(u-boot-env),5m(kernel),-(rootfs)"
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0x260000 /* environment starts here */
+#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
+
+/*
+ * USB configuration.  We enable MUSB support, both for host and for
+ * gadget.  We set USB0 as peripheral and USB1 as host, based on the
+ * board schematic and physical port wired to each.  Then for host we
+ * add mass storage support.
+ */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_GADGET
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW	2
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE	MUSB_PERIPHERAL
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#if defined(CONFIG_MUSB_HOST)
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif
+
+#if defined(CONFIG_SPL_BUILD)
+/* disable host part of MUSB in SPL */
+#undef CONFIG_MUSB_HOST
+/* Disable CPSW SPL support so we fit within the 101KiB limit. */
+#undef CONFIG_SPL_ETH_SUPPORT
+#endif
+
+/* Network */
+#define CONFIG_CMD_MII
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR		1
+#define CONFIG_PHY_RESET	1
+#define CONFIG_PHY_NATSEMI
+
+/* CPSW support */
+#define CONFIG_SPL_ETH_SUPPORT
+
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#endif	/* ! __CONFIG_PENGWYN_H */
--- a/include/configs/tao3530.h
+++ b/include/configs/tao3530.h
@ -83,6 +83,13 @@
 #define CONFIG_OMAP_HSMMC
 #define CONFIG_DOS_PARTITION

+/* GPIO banks */
+#define CONFIG_OMAP3_GPIO_2		/* GPIO32 ..63  is in GPIO bank 2 */
+#define CONFIG_OMAP3_GPIO_3		/* GPIO64 ..95  is in GPIO bank 3 */
+#define CONFIG_OMAP3_GPIO_4		/* GPIO96 ..127 is in GPIO bank 4 */
+#define CONFIG_OMAP3_GPIO_5		/* GPIO128..159 is in GPIO bank 5 */
+#define CONFIG_OMAP3_GPIO_6		/* GPIO160..191 is in GPIO bank 6 */
+
 /* commands to include */
 #include <config_cmd_default.h>

--- a/include/configs/ti_am335x_common.h
+++ b/include/configs/ti_am335x_common.h
@ -13,7 +13,6 @@
 #define __CONFIG_TI_AM335X_COMMON_H__

 #define CONFIG_AM33XX
-#define CONFIG_BOARD_LATE_INIT
 #define CONFIG_ARCH_CPU_INIT
 #define CONFIG_SYS_CACHELINE_SIZE       64
 #define CONFIG_MAX_RAM_BANK_SIZE	(1024 << 20)	/* 1GB */
--- a/include/configs/ti_omap4_common.h
+++ b/include/configs/ti_omap4_common.h
@ -163,4 +163,10 @@
 #define CONFIG_SPL_NAND_AM33XX_BCH	/* ELM support */
 #endif

+#ifdef CONFIG_SPL_BUILD
+/* No need for i2c in SPL mode as we will use SRI2C for PMIC access on OMAP4 */
+#undef CONFIG_SYS_I2C
+#undef CONFIG_SYS_I2C_OMAP24XX
+#endif
+
 #endif /* __CONFIG_TI_OMAP4_COMMON_H */
--- a/include/configs/tseries.h
+++ b/include/configs/tseries.h
@ -0,0 +1,265 @@
+/*
+ * tseries.h
+ *
+ * specific parts for B&R T-Series Motherboard
+ *
+ * Copyright (C) 2013 Hannes Petermaier <oe5hpm@oevsv.at> -
+ * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
+ *
+ * SPDX-License-Identifier:        GPL-2.0+
+ */
+
+#ifndef __CONFIG_TSERIES_H__
+#define __CONFIG_TSERIES_H__
+
+#include <configs/bur_am335x_common.h>
+/* ------------------------------------------------------------------------- */
+/* Clock Defines */
+#define V_OSCK				26000000  /* Clock output from T2 */
+#define V_SCLK				(V_OSCK)
+
+#define CONFIG_POWER_TPS65217
+
+/* Support both device trees and ATAGs. */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMD_BOOTZ
+/*#define CONFIG_MACH_TYPE		3589*/
+#define CONFIG_MACH_TYPE		0xFFFFFFFF /* TODO: check with kernel*/
+
+/* MMC/SD IP block */
+#if defined(CONFIG_EMMC_BOOT)
+ #define CONFIG_MMC
+ #define CONFIG_GENERIC_MMC
+ #define CONFIG_OMAP_HSMMC
+ #define CONFIG_CMD_MMC
+ #define CONFIG_SUPPORT_EMMC_BOOT
+/* RAW SD card / eMMC locations. */
+ #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /*addr. 0x60000 */
+ #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS		0x200 /* 256 KB */
+ #define CONFIG_SPL_MMC_SUPPORT
+#endif /* CONFIG_EMMC_BOOT */
+
+/*
+ * When we have SPI or NAND flash we expect to be making use of mtdparts,
+ * both for ease of use in U-Boot and for passing information on to
+ * the Linux kernel.
+ */
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND)
+#define CONFIG_MTD_DEVICE		/* Required for mtdparts */
+#define CONFIG_CMD_MTDPARTS
+#endif /* CONFIG_SPI_BOOT, ... */
+
+#undef CONFIG_SPL_OS_BOOT
+#ifdef CONFIG_SPL_OS_BOOT
+#define CONFIG_SYS_SPL_ARGS_ADDR		0x80F80000
+
+/* RAW SD card / eMMC */
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR	0x900	/* address 0x120000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR	0x80	/* address 0x10000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS	0x80	/* 64KiB */
+
+/* NAND */
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_SPL_NAND_OFS			0x080000 /* end of u-boot */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS		0x140000
+#define CONFIG_CMD_SPL_WRITE_SIZE		0x2000
+#endif /* CONFIG_NAND */
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_AM33XX_BCH	/* OMAP4 and later ELM support */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+#endif /* CONFIG_NAND */
+
+/* Always 128 KiB env size */
+#define CONFIG_ENV_SIZE			(128 << 10)
+
+#ifdef CONFIG_NAND
+#define NANDARGS \
+	"mtdids=" MTDIDS_DEFAULT "\0" \
+	"mtdparts=" MTDPARTS_DEFAULT "\0" \
+	"nandargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=${nandroot} " \
+		"rootfstype=${nandrootfstype}\0" \
+	"nandroot=ubi0:rootfs rw ubi.mtd=8,2048\0" \
+	"nandrootfstype=ubifs rootwait=1\0" \
+	"nandimgsize=0x500000\0" \
+	"nandboot=echo Booting from nand ...; " \
+		"run nandargs; " \
+		"nand read ${loadaddr} kernel ${nandimgsize}; " \
+		"bootz ${loadaddr}\0"
+#else
+#define NANDARGS ""
+#endif /* CONFIG_NAND */
+
+#ifdef CONFIG_MMC
+#define MMCARGS \
+	"silent=1\0"
+#else
+#define MMCARGS ""
+#endif /* CONFIG_MMC */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"autoload=0\0" \
+	"loadaddr=0x80200000\0" \
+	"bootfile=zImage\0" \
+	"console=ttyO0,115200n8\0" \
+	"optargs=\0" \
+	"rootpath=/tftpboot/tseries/rootfs-small\0" \
+	"nfsopts=nolock\0" \
+	"netargs=setenv bootargs console=${console} " \
+		"${optargs} " \
+		"root=/dev/nfs " \
+		"nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+		"ip=dhcp\0" \
+	"netboot=echo Booting from network ...; " \
+		"setenv autoload no; " \
+		"dhcp; " \
+		"tftp ${loadaddr} ${bootfile}; " \
+		"run netargs; " \
+		"bootm ${loadaddr}\0" \
+	"usbupdate=echo Updating UBOOT from USB-Stick ...; " \
+		"usb start; " \
+		"fatload usb 0 0x80000000 updateubootusb.img; " \
+		"source;\0" \
+	"netupdate=echo Updating UBOOT from Network (TFTP) ...; " \
+		"setenv autoload 0; " \
+		"dhcp;" \
+		"tftp 0x80000000 updateUBOOT.img;" \
+		"source;\0" \
+	NANDARGS \
+	MMCARGS
+#endif /* !CONFIG_SPL_BUILD*/
+
+#define CONFIG_BOOTCOMMAND \
+	"run mmcboot1;"
+#define CONFIG_BOOTDELAY		1 /* TODO: für release auf 0 setzen */
+
+#ifdef CONFIG_NAND
+/*
+ * GPMC  block.  We support 1 device and the physical address to
+ * access CS0 at is 0x8000000.
+ */
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		0x8000000
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_CMD_NAND
+/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */
+#define CONFIG_NAND_OMAP_ELM
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
+#define GPMC_NAND_ECC_LP_x16_LAYOUT	1
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
+					CONFIG_SYS_NAND_PAGE_SIZE)
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9, \
+					10, 11, 12, 13, 14, 15, 16, 17, \
+					18, 19, 20, 21, 22, 23, 24, 25, \
+					26, 27, 28, 29, 30, 31, 32, 33, \
+					34, 35, 36, 37, 38, 39, 40, 41, \
+					42, 43, 44, 45, 46, 47, 48, 49, \
+					50, 51, 52, 53, 54, 55, 56, 57, }
+
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	14
+
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+#define MTDIDS_DEFAULT			"nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT		"mtdparts=omap2-nand.0:" \
+					"128k(SPL)," \
+					"128k(SPL.backup1)," \
+					"128k(SPL.backup2)," \
+					"128k(SPL.backup3)," \
+					"512k(u-boot)," \
+					"128k(u-boot-spl-os)," \
+					"128k(u-boot-env)," \
+					"5m(kernel),"\
+					"-(rootfs)"
+#endif /* CONFIG_NAND */
+
+/* USB configuration */
+#define CONFIG_USB_MUSB_DSPS
+#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_MUSB_PIO_ONLY
+#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT
+/* attention! not only for gadget, enables also highspeed in hostmode */
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_MUSB_HOST
+#define CONFIG_AM335X_USB0
+#define CONFIG_AM335X_USB0_MODE	MUSB_HOST
+#define CONFIG_AM335X_USB1
+#define CONFIG_AM335X_USB1_MODE MUSB_HOST
+
+#ifdef CONFIG_MUSB_HOST
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#endif /* CONFIG_MUSB_HOST */
+
+#if defined(CONFIG_SPI_BOOT)
+/* McSPI IP block */
+#define CONFIG_SPI
+#define CONFIG_OMAP3_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SF_DEFAULT_SPEED		24000000
+
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS		0
+#define CONFIG_SPL_SPI_CS		0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
+#define CONFIG_ENV_SECT_SIZE		(4 << 10) /* 4 KB sectors */
+#define CONFIG_ENV_OFFSET		(768 << 10) /* 768 KiB in */
+#define CONFIG_ENV_OFFSET_REDUND	(896 << 10) /* 896 KiB in */
+
+#elif defined(CONFIG_EMMC_BOOT)
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		1
+#define CONFIG_SYS_MMC_ENV_PART		2
+#define CONFIG_ENV_OFFSET		0x40000	/* TODO: Adresse definieren */
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#elif defined(CONFIG_NAND)
+#undef CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		0x120000 /* TODO: Adresse definieren */
+#define CONFIG_SYS_ENV_SECT_SIZE	CONFIG_ENV_SIZE
+#else
+#error "no storage for Environment defined!"
+#endif
+/*
+ * Common filesystems support.  When we have removable storage we
+ * enabled a number of useful commands and support.
+ */
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_CMD_FS_GENERIC
+#endif /* CONFIG_MMC, ... */
+
+#endif	/* ! __CONFIG_TSERIES_H__ */