Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This change lays the groundwork for the BOOTFLAG_* flags being removed.
This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
included the mpc8308_p1m board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC83xx SERDES control is different from the other FSL PPC chips.
For now lets split it out so we can standardize on interfaces for
determining of a device on SERDES is configured.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Update 83xx architecture's CONFIG_ECC_INIT_VIA_DDRC references to
CONFIG_ECC_INIT_VIA_DDRCONTROLLER, which other Freescale architectures
use
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837xE specs says that SerDes1 has:
— Two lanes running x1 SGMII at 1.25 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
And for SerDes2:
— Two lanes running x1 PCI Express at 2.5 Gbps;
— One lane running x2 PCI Express at 2.5 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
The spec also explicitly states that PEX options are not valid for
the SD1.
Nevertheless MPC8378 RDB and MDS boards configure the SD1 for PEX,
which is wrong to do.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
in the spirit of commit 1ced121600,
85xx's "Update SVR numbers to expand support", simplify SPRIDR processing
and processor ID display. Add REVID_{MAJ,MIN}OR macros to make
REVID dependent code simpler. Also added PARTID_NO_E and IS_E_PROCESSOR
convenience macros.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk
Peter Tyser
Kumar Gala
Kim Phillips
Anton Vorontsov
Jean-Christophe PLAGNIOL-VILLARD
Becky Bruce
Timur Tabi
Jon Loeliger