The DTS file for armada-37xx uses the string "marvell,armada3700-ehci",
but the code searched for "marvell,armada-3700-ehci".
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the reg_set* functions into comphy.h as static inline functions.
Change return type of get_*_string to const char *.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SGMII initialization PIN_PIPE_SEL has to be zero when resetting
the PHY. Since comphy_mux already set the selector register to
correct values, we have to store it's value before setting it to 0
and restore it after SGMII init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The register addresses on lanes 0 and 1 are switched, first comes 1 and
then 0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently comphy_mux supports only trivial order of nodes in pin
selector register, that is lane N on position N*bitcount.
Add support for nontrivial order, with map stored in device tree
property mux-lane-order.
This is needed for Armada 37xx.
As far as I know, there is no driver for Armada 37xx comphy in the
kernel. When such a driver comes, this will need to be rewritten to
support the device tree bindings from the kernel.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is based on commit d9899826 by
zachary <zhangzg@marvell.com>
from u-boot-marvell, see
github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/d9899826
- According to design specification, the transmitter should be set to high
impedence mode during electrical idle. Thus transmitter should detect RX
at high impedence mode also, and delay is needed to accommodate high
impedence off latency. Otherwise the USB3 will have detection issue that
most of the time the USB3 device can not be detected at all, or be
detected as USB2 device sometimes.
Modified registers: RD005C302h (R181h) (0051h) Lane Configuration 1
Bit 6: set to 1 to let Tx detect Rx at HiZ mode
Bit [3:4]: set to 2 to be delayed by 2 clock cycles
Bit 0: set to 1 to set transmitter to high impedance mode during idle.
- USB3 De-emphasize level of -3.5dB is mandatory, but USB3 MAC selects 0x2
(emphasize disabled) in the MAC_PHY_TXDEEMPH [1:0], while it is supposed
to select 0x1(3.5dB emphasize). Thus need to override what comes from
the MAC(by setting register 0x1c2 bit2 to 0x1) and to configure the
overridded values of MAC_PHY_TXDEEMPH [1:0] to 0x1(bit15 of register
0x181 and bit0 of register 0x180).
- According to USB3 application note, need to update below comphy
registers:
Set max speed generation to USB3.0 5Gbps(set RD005C04Ah bit[11:10] to 1)
Set capacitor value to 0xF(set RF005C224 bit[3:0] to 0xF)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
According to specification, CFG_PM_RXDLOZ_WAIT should be set to 0x7
when reference clock is at 25 MHz. The specification (at least the
version I have) does not mentoin the setting for 40 MHz reference
clock, but Marvell's U-Boot sets 0xC in that case.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When USB3 is on comphy lane 2 on the Armada 37xx, the registers
have to be accessed indirectly via SATA indirect access.
This is the case of the Turris Mox board from CZ.NIC.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Create a special function for indirect register setting,
reg_set_indirect, and use it instead of the two calls to reg_set.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In U-Boot it is usually written this way.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The timeout is set to PLL_LOCK_TIMEOUT in every call to
comphy_poll_reg. Remove this parameter from the function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently there is for each register special functional macro, ie:
LANE_CFG1_ADDR(u)
GLOB_CLK_SRC_LO_ADDR(u)
...
where can be either PCIE or USB3.
Change this to one function PHY_ADDR(unit, addr). The code becomes:
phy_addr(PCIE, LANE_CFG1)
phy_addr(PCIE, GLOB_CLK_SRC_LO)
...
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro phy_write16 is not used by the rest of the code,
phy_read16 is not used at all.
We also change the macro SGMIIPHY_ADDR to a static inline function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
All the calls to reg_set and friends have to cast the first argument
to void __iomem *. Lets change the return type of the MVEBU_REG macro
instead.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add PCIE analog parameters initialization values according to
latest ETP.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
No functional change.
The variable name "comphy_index" is misleading, it represents
cp index and not comphy index.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add SFI analog parameters initialization values according to
latest ETP.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
since now the COMPHY can also be ignored, we must know the
state of the COMPHY. we cannot assume anymore that a missing
COMPHY is unconnected.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The comphy configuration is incorrect.
Set the correct values for SGMII.
In addition, remove xaui from the comment as it is not supported.
Signed-off-by: Yoav Gvili <ygvili@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the option to configure a comphy to 5G XFI mode.
In order to configure the comphy to 5G XFI, update
the comphy node in the device-tree:
phy2 {
phy-type = <PHY_TYPE_SFI>;
phy-speed = <PHY_SPEED_5_15625G>;
};
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add SATA analog parameters initialization values according to
latest ETP.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch fixes the following:
1. KR/SFI on lane #4 mux selector is 0x2 and not 0x1
2. Comment typo
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This type tells u-boot to preserve the COMPHY settings as is
it is usefull in situations where the COMPHY was initialized by
earlier firmware.
Note that IGNORE is different from UNCONNECTED since setting
UNCONNECTED type will disconnect the COMPHY in the COMPHY MUX
which is a desired behaviour
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The serdes was always configured in root complex mode.
this patch add new entry in device tree (per serdes)
which indicates whether the serdes is in end point mode.
if so, it skips the root complex configuration.
Signed-off-by: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use local static counter for maintaining the COMPHY chip-ID
upon its initialization.
The dev->seq originally used as the COMPHY chip-ID depends
on the device tree scan order and produces wrong results
that breaks the deficated PHYs init flow, which in turn
breaks the USB support.
Change-Id: I4e3f7ec36590a7f95dc94d9269a3c47fb708c4a9
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the SD/SDIO/MMC DT properties are updated in the Marvell
A3700 and A7/8k DT files, we need to match the checks for compatible
node in the PHY driver as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the support for the Armada 8k, a 2nd COMPHY controller now needs
to get supported from the CP110 slave controller. This patch adds support
for this 2nd contoller in the COMPHY driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Obviously the mask for the rx and tx select field cannot be right,
as it would overlap in one and exceed the 32-bit register in the other
case. From looking at the neighbouring bits it looks like the mask
should be really 4 bits wide instead of 8.
Pointed out by a GCC 6.2 (default) warning.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
The signature for this macro has changed. Bring in the upstream version and
adjust U-Boot's usages to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update to drivers/power/pmic/palmas.c:
Signed-off-by: Keerthy <j-keerthy@ti.com>
Change-Id: I6cc9021339bfe686f9df21d61a1095ca2b3776e8
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Marek Behún
zachary
Tom Rini
Masahiro Yamada
Simon Glass
Igal Liberman
Stefan Roese
Konstantin Porotchkin
Andre Przywara