nand_info is used all over the file so abstract it with
get_nand_dev_by_index() which will help for DM conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
If the value of either "nand options" or "bbt options" has a zero in
the most significant nibble, the '0x' prefix will be isolated from the
value like shown below:
|Device 0: nand0, sector size 128 KiB
| Page size 2048 b
| OOB size 64 b
| Erase size 131072 b
| subpagesize 2048 b
| options 0x40000200
| bbt options 0x 60000
Change the format string to produce leading zeroes filling the gap.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Looks like we have few more places where we're testing for
nand_info[i]->name. We can now use just test for nand_info[i]
instead.
This fixes a data abort on devices with no NAND when doing
nand info.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If we do nand device 0 command in u-boot on a device that has NAND support
enabled but no NAND chip, we can get data abort at least on omaps.
Fix the issue by replacing the check with nand_info[dev] as
suggested by Scott Wood. The check for name existed before because before
the array-to-pointer conversion there was no way to directly test
nand_info[dev] for emptiness.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modern NANDs do not guarantee that data written in raw mode will not
contain bitflips just after writing them. This is fine since the number
of bitflips should be rather low and thus fixable by the ECC engine,
but since we are reading data in raw mode to verify if they match the
input data we cannot prevent failures if some bits are flipped.
The option of using standard mode to verify the data is not acceptable
either, since one of the usage of raw mode is to allow flashing images
that do not respect the standard NAND page layout or the default ECC
config (this is the case on Allwinner platforms, where the ROM code
tests several hardcoded configs, which are not necessarily matching the
NAND characteristics).
Add an extension to the nand write.raw command allowing one to disable
the verification step.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
nand torture currently works on exactly one nand block which is specified
by giving the byteoffset to the beginning of the block.
Extend this by allowing for a second parameter specifying the byte size
to be tested.
e.g.
==> nand torture 1000000
NAND torture: device 0 offset 0x1000000 size 0x20000 (block size 0x20000)
Passed: 1, failed: 0
==> nand torture 1000000 40000
NAND torture: device 0 offset 0x1000000 size 0x40000 (block size 0x20000)
Passed: 2, failed: 0
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
[scottwood: fix usage to show size as optional, and add misssing braces]
Signed-off-by: Scott Wood <oss@buserror.net>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Now that they are in their own directory, we can remove this prefix.
This makes it easier to find a file since the prefix does not get in the
way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
There are a lot of unrelated files in common, including all of the commands.
Moving them into their own directory makes them easier to find and is more
logical.
Some commands include non-command code, such as cmd_scsi.c. This should be
sorted out at some point so that the function can be enabled with or without
the associated command.
Unfortunately, with m68k I get this error:
m68k: + M5329AFEE
+arch/m68k/cpu/mcf532x/start.o: In function `_start':
+arch/m68k/cpu/mcf532x/start.S:159:(.text+0x452): relocation truncated to fit: R_68K_PC16 against symbol `board_init_f' defined in .text.board_init_f section in common/built-in.o
I hope someone can shed some light on what this means. I hope it isn't
depending on the position of code in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years. If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling. This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.
U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Previously NAND writes were only verified when CONFIG_MTD_NAND_VERIFY_WRITE
was defined. On boards without this define writes could fail silently.
Boards with CONFIG_MTD_NAND_VERIFY_WRITE could prematurely report
failures which ECC could correct.
Add a verification step after all "nand write[.x]" commands to ensure the
writes were successful. The verification uses ECC for for "normal"
writes, but does not for raw and yaffs writes. Some test cases which
inject fake bad bits on a 2K page flash are below.
Test cases with CONFIG_MTD_NAND_VERIFY_WRITE defined:
Example of an ECC write which previously failed when
CONFIG_MTD_NAND_VERIFY_WRITE was defined, but now succeeds because ECC
is used during verification:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0x01 1
nand write 0x1000000 0x800 0x1800
Test cases without CONFIG_MTD_NAND_VERIFY_WRITE defined:
Example of an ECC write which previously silently failed:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0x00 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0xff 1
nand write 0x1000000 0x800 0x1800
Example of a raw write which previously failed silently due to stuck
data bit, but now errors out:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10020 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000020 0x01 1
nand write.raw 0x1000000 0x800 3
Example of a raw write which previously failed silently due to stuck OOB
bit, but now errors out:
nand erase 0 0x10000
dhcp /somefile
mw.b 0x10000 0xff 0x2000
mw.b 0x10810 0xfe 1
nand write.raw 0x10000 0x800 1
mw.b 0x1000810 0x01 1
nand write.raw 0x1000000 0x800 3
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
The arg_off() and arg_off_size() update the 'current NAND
device' variable (dev). This is then used when assigning the
(nand_info_t*)nand value. Place the assignment after the
arg_off(_size) calls to prevent using incorrect (nand_info_t*)
nand value.
Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
make the use of legacy image format configurable through
the config define CONFIG_IMAGE_FORMAT_LEGACY.
When relying on signed FIT images with required signature check
the legacy image format should be disabled. Therefore introduce
this new define and enable legacy image format if CONFIG_FIT_SIGNATURE
is not set. If CONFIG_FIT_SIGNATURE is set disable per default
the legacy image format.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lars Steubesand <lars.steubesand@philips.com>
Cc: Mike Pearce <mike@kaew.be>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
User's confirmation is asked in different commands. This commit adds a
function for such confirmation.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
When executing nand scrub, the user gets the prompt:
Really scrub this NAND flash? <y/N>
We do not want the annoying usage displayed when saying N here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If a non-zero value is given to only_oob argument,
printing the main area is skipped.
With a little modification, we can skip the whole
while loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
adjust_size_for_badblocks reduces the operation size to account
for the block skipping done by the read/write functions when an
interval (partition name or whole chip) is specified rather than a data
amount.
Erase does not do block skipping, except for erase.spread which takes
a data amount rather than an interval (and thus already does not call
adjust_size_for_badblocks). Calling adjust_size_for_badblocks when
block skipping is not done means that if bad blocks are present,
the "nand erase.part" and "nand erase.chip" commands will fail to erase
blocks at the end of the interval.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Harvey Chapman <hchapman@3gfp.com>
Acked-by: Heiko Schocher <hs@denx.de>
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Adjust the sizes calculated for whole partition/chip operations by
removing the size of bad blocks so we don't try to erase/read/write
past a partition/chip boundary.
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
"nand read.part addr off size" would be treated as "nand read.raw addr off 1"
It now fails as intended stating "Unknown nand command suffix '.part'"
Signed-off-by: Harvey Chapman <hchapman@3gfp.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
cmd_boot.c:40:5: warning: symbol 'do_go' was not declared. Should it be static?
cmd_bootm.c:164:6: warning: symbol '__arch_preboot_os' was not declared. Should it be static?
cmd_bootm.c:477:5: warning: symbol 'do_bootm_subcommand' was not declared. Should it be static?
cmd_bootm.c:1022:1: error: directive in argument list
cmd_bootm.c:1028:1: error: directive in argument list
cmd_bootm.c:1029:1: error: directive in argument list
cmd_bootm.c:1036:1: error: directive in argument list
cmd_bootm.c:1042:1: error: directive in argument list
cmd_bootm.c:1044:1: error: directive in argument list
cmd_bootm.c:1045:1: error: directive in argument list
cmd_bootm.c:1047:1: error: directive in argument list
cmd_bootm.c:1089:5: warning: symbol 'do_iminfo' was not declared. Should it be static?
cmd_bootm.c:1176:5: warning: symbol 'do_imls' was not declared. Should it be static?
cmd_bootm.c:1654:1: error: directive in argument list
cmd_bootm.c:1660:1: error: directive in argument list
cmd_console.c:32:5: warning: symbol 'do_coninfo' was not declared. Should it be s
cmd_date.c:46:5: warning: symbol 'do_date' was not declared. Should it be static?
cmd_echo.c:27:5: warning: symbol 'do_echo' was not declared. Should it be static?
cmd_exit.c:27:5: warning: symbol 'do_exit' was not declared. Should it be static?
cmd_fat.c:97:5: warning: symbol 'do_fat_ls' was not declared. Should it be static?
cmd_fat.c:136:5: warning: symbol 'do_fat_fsinfo' was not declared. Should it be s
cmd_fdt.c:66:5: warning: symbol 'do_fdt' was not declared. Should it be static?
cmd_fdt.c:542:43: warning: incorrect type in assignment (different base types)
cmd_fdt.c:542:43: expected unsigned int [unsigned] [usertype] <noident>
cmd_fdt.c:542:43: got restricted __be32 [usertype] <noident>
cmd_fdt.c:679:42: warning: cast to restricted __be32
cmd_fdt.c:820:1: error: directive in argument list
cmd_fdt.c:822:1: error: directive in argument list
cmd_flash.c:292:5: warning: symbol 'do_flinfo' was not declared. Should it be static?
cmd_flash.c:324:5: warning: symbol 'do_flerase' was not declared. Should it be static?
cmd_flash.c:457:5: warning: symbol 'do_protect' was not declared. Should it be st
cmd_help.c:27:5: warning: symbol 'do_help' was not declared. Should it be static?
cmd_i2c.c:136:6: warning: symbol '__def_i2c_init_board' was not declared. Should it be static?
cmd_i2c.c:144:14: warning: symbol '__def_i2c_get_bus_speed' was not declared. Should it be static?
cmd_i2c.c:151:5: warning: symbol '__def_i2c_set_bus_speed' was not declared. Should it be static?
cmd_i2c.c:1322:1: error: directive in argument list
cmd_i2c.c:1324:1: error: directive in argument list
cmd_i2c.c:1326:1: error: directive in argument list
cmd_i2c.c:1328:1: error: directive in argument list
cmd_i2c.c:1337:1: error: directive in argument list
cmd_i2c.c:1339:1: error: directive in argument list
cmd_irq.c:27:5: warning: symbol 'do_interrupts' was not declared. Should it be static?
cmd_itest.c:133:5: warning: symbol 'binary_test' was not declared. Should it be static?
cmd_itest.c:158:5: warning: symbol 'do_itest' was not declared. Should it be stat
cmd_load.c:54:5: warning: symbol 'do_load_serial' was not declared. Should it be static?
cmd_load.c:431:6: warning: symbol 'his_eol' was not declared. Should it be static?
cmd_load.c:432:6: warning: symbol 'his_pad_count' was not declared. Should it be static?
cmd_load.c:433:6: warning: symbol 'his_pad_char' was not declared. Should it be static?
cmd_load.c:434:6: warning: symbol 'his_quote' was not declared. Should it be static?
cmd_load.c:436:5: warning: symbol 'do_load_serial_bin' was not declared. Should it be static?
cmd_load.c:549:6: warning: symbol 'send_pad' was not declared. Should it be static?
cmd_load.c:558:6: warning: symbol 'ktrans' was not declared. Should it be static?
cmd_load.c:568:5: warning: symbol 'chk1' was not declared. Should it be static?
cmd_load.c:578:6: warning: symbol 's1_sendpacket' was not declared. Should it be static?
cmd_load.c:587:6: warning: symbol 'send_ack' was not declared. Should it be static?
cmd_load.c:600:6: warning: symbol 'send_nack' was not declared. Should it be static?
cmd_load.c:614:6: warning: symbol 'os_data_init' was not declared. Should it be static?
cmd_load.c:615:6: warning: symbol 'os_data_char' was not declared. Should it be static?
cmd_load.c:657:6: warning: symbol 'k_data_init' was not declared. Should it be static?
cmd_load.c:663:6: warning: symbol 'k_data_save' was not declared. Should it be static?
cmd_load.c:669:6: warning: symbol 'k_data_restore' was not declared. Should it be static?
cmd_load.c:675:6: warning: symbol 'k_data_char' was not declared. Should it be static?
cmd_load.c:693:6: warning: symbol 'send_parms' was not declared. Should it be static?
cmd_load.c:694:6: warning: symbol 'send_ptr' was not declared. Should it be static?
cmd_load.c:698:6: warning: symbol 'handle_send_packet' was not declared. Should i
cmd_mdio.c:60:5: warning: symbol 'mdio_write_ranges' was not declared. Should it be static?
cmd_mdio.c:82:5: warning: symbol 'mdio_read_ranges' was not declared. Should it be static?
cmd_mdio.c:115:5: warning: symbol 'extract_reg_range' was not declared. Should it be static?
cmd_mdio.c:144:5: warning: symbol 'extract_phy_range' was not declared. Should it
cmd_mem.c:54:5: warning: symbol 'do_mem_md' was not declared. Should it be static?
cmd_mem.c:150:5: warning: symbol 'do_mem_mm' was not declared. Should it be static?
cmd_mem.c:154:5: warning: symbol 'do_mem_nm' was not declared. Should it be static?
cmd_mem.c:159:5: warning: symbol 'do_mem_mw' was not declared. Should it be static?
cmd_mem.c:256:5: warning: symbol 'do_mem_cmp' was not declared. Should it be static?
cmd_mem.c:326:5: warning: symbol 'do_mem_cp' was not declared. Should it be static?
cmd_mem.c:436:5: warning: symbol 'do_mem_base' was not declared. Should it be static?
cmd_mem.c:449:5: warning: symbol 'do_mem_loop' was not declared. Should it be static?
cmd_mem.c:595:5: warning: symbol 'do_mem_mtest' was not declared. Should it be static?
cmd_mem.c:618:26: warning: Using plain integer as NULL pointer
cmd_mem.c:1057:5: warning: symbol 'do_mem_crc' was not declared. Should it be static?
cmd_misc.c:30:5: warning: symbol 'do_sleep' was not declared. Should it be static
cmd_mmc.c:118:5: warning: symbol 'do_mmcinfo' was not declared. Should it be static?
cmd_mmc.c:272:32: warning: Using plain integer as NULL pointer
cmd_mmc.c:150:5: warning: symbol 'do_mmcops' was not declared. Should it be stati
cmd_mp.c:27:1: warning: symbol 'cpu_cmd' was not declared. Should it be static?
cmd_mp.c:85:1: error: directive in argument list
cmd_mp.c:88:1: error: directive in argument list
cmd_mtdparts.c:150:18: warning: symbol 'mtdids' was not declared. Should it be static?
cmd_mtdparts.c:153:18: warning: symbol 'devices' was not declared. Should it be static?
cmd_mtdparts.c:713:5: warning: symbol 'mtd_device_validate' was not declared. Should it be static?
cmd_mtdparts.c:1887:5: warning: symbol 'do_chpart' was not declared. Should it be static?
cmd_mtdparts.c:1925:5: warning: symbol 'do_mtdparts' was not declared. Should it be static?
cmd_mtdparts.c:2060:1: error: directive in argument list
cmd_mtdparts.c:2063:1: error: directive in argument list
cmd_mtdparts.c:2066:1: error: directive in argument list
cmd_mtdparts.c:2071:1: error: directive in argument list
cmd_mtdparts.c:2073:1: error: directive in argument list
cmd_nand.c:377:18: error: bad constant expression
cmd_nand.c:431:5: warning: symbol 'do_nand' was not declared. Should it be static?
cmd_nand.c:796:1: error: directive in argument list
cmd_nand.c:801:1: error: directive in argument list
cmd_nand.c:802:1: error: directive in argument list
cmd_nand.c:806:1: error: directive in argument list
cmd_nand.c:819:1: error: directive in argument list
cmd_nand.c:824:1: error: directive in argument list
cmd_nand.c:825:1: error: directive in argument list
cmd_nand.c:831:1: error: directive in argument list
cmd_nand.c:918:5: warning: symbol 'do_nandboot' was not declared. Should it be static?
cmd_net.c:33:5: warning: symbol 'do_bootp' was not declared. Should it be static?
cmd_net.c:107:5: warning: symbol 'do_dhcp' was not declared. Should it be static?
cmd_net.c:120:5: warning: symbol 'do_nfs' was not declared. Should it be static?
cmd_nvedit.c:138:5: warning: symbol 'do_env_print' was not declared. Should it be static?
cmd_nvedit.c:323:5: warning: symbol '_do_env_set' was not declared. Should it be static?
cmd_nvedit.c:435:5: warning: symbol 'do_env_set' was not declared. Should it be static?
cmd_nvedit.c:514:5: warning: symbol 'do_env_edit' was not declared. Should it be static?
cmd_nvedit.c:620:5: warning: symbol 'do_env_save' was not declared. Should it be static?
cmd_nvedit.c:1016:1: error: directive in argument list
cmd_nvedit.c:1018:1: error: directive in argument list
cmd_nvedit.c:1021:1: error: directive in argument list
cmd_nvedit.c:1023:1: error: directive in argument list
cmd_nvedit.c:1024:1: error: directive in argument list
cmd_nvedit.c:1026:1: error: directive in argument list
cmd_nvedit.c:1027:1: error: directive in argument list
cmd_nvedit.c:1029:1: error: directive in argument list
cmd_nvedit.c:1030:1: error: directive in argument list
cmd_nvedit.c:1032:1: error: directive in argument list
cmd_nvedit.c:1034:1: error: directive in argument list
cmd_nvedit.c:1036:1: error: directive in argument list
cmd_nvedit.c:1037:1: error: directive in argument list
cmd_nvedit.c:1039:1: error: directive in argument list
cmd_pci.c:38:17: warning: symbol 'ShortPCIListing' was not declared. Should it be static?
cmd_pci.c:38:22: warning: 'ShortPCIListing' defined but not used [-Wunused-variable]
cmd_pci.c:411:5: warning: symbol 'do_pci' was not declared. Should it be static?
cmd_pci.c:494:1: error: directive in argument list
cmd_pci.c:497:1: error: directive in argument list
cmd_reginfo.c:40:5: warning: symbol 'do_reginfo' was not declared. Should it be static?
cmd_sata.c:31:5: warning: symbol 'sata_curr_device' was not declared. Should it be static?
note -> ata_piix.c doesn't seem to use 'sata_curr_device'; deleted.
cmd_sata.c:32:18: warning: symbol 'sata_dev_desc' was not declared. Should it be static?
cmd_sata.c:70:5: warning: symbol 'do_sata' was not declared. Should it be static?
cmd_setexpr.c:53:5: warning: symbol 'do_setexpr' was not declared. Should it be static?
cmd_source.c:186:1: error: directive in argument list
cmd_source.c:190:1: error: directive in argument list
cmd_test.c:27:5: warning: symbol 'do_test' was not declared. Should it be static?
cmd_test.c:153:5: warning: symbol 'do_false' was not declared. Should it be static?
cmd_test.c:164:5: warning: symbol 'do_true' was not declared. Should it be static
cmd_usb.c:43:6: warning: symbol 'usb_get_class_desc' was not declared. Should it be static?
cmd_usb.c:69:6: warning: symbol 'usb_display_class_sub' was not declared. Should it be static?
cmd_usb.c:151:6: warning: symbol 'usb_display_string' was not declared. Should it be static?
cmd_usb.c:161:6: warning: symbol 'usb_display_desc' was not declared. Should it be static?
cmd_usb.c:195:6: warning: symbol 'usb_display_conf_desc' was not declared. Should it be static?
cmd_usb.c:210:6: warning: symbol 'usb_display_if_desc' was not declared. Should it be static?
cmd_usb.c:227:6: warning: symbol 'usb_display_ep_desc' was not declared. Should it be static?
cmd_usb.c:252:6: warning: symbol 'usb_display_config' was not declared. Should it be static?
cmd_usb.c:283:6: warning: symbol 'usb_show_tree_graph' was not declared. Should it be static?
cmd_usb.c:343:6: warning: symbol 'usb_show_tree' was not declared. Should it be static?
cmd_usb.c:356:5: warning: symbol 'do_usbboot' was not declared. Should it be static?
cmd_usb.c:366:5: warning: symbol 'do_usb' was not declared. Should it be static?
cmd_version.c:31:5: warning: symbol 'do_version' was not declared. Should it be s
cmd_ximg.c:46:1: warning: symbol 'do_imgextract' was not declared. Should it be static?
cmd_ximg.c:272:1: error: directive in argument list
cmd_ximg.c:276:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
In order for cache invalidation and flushing to work properly, the data
and OOB buffers must be aligned to full cache lines.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 418396e212 introduced a
bug that causes nand read and nand write to crash in strcmp
due to a null pointer.
Root cause is that strchr(cmd, '.') returns a null pointer when
the input string does not contain a '.'
The strcmp function does not check for null pointers, resulting
in a crash.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Scott Wood <scott@tyr.buserror.net>
cmd_nand.c: In function 'raw_access':
cmd_nand.c:397:9: warning: variable 'rwsize' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
A use for this is to read, modify, erase, and write an entire block as a
single unit, as a replacement for the biterr command. This way gives
more flexibility in that you can also test multiple bit errors, errors
in the ECC, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
cmd_nand.c: In function ‘arg_off_size’:
cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
With 2a8e0fc nand_do_read_ops changed in behavior slightly (keeping in sync
with the kernel which did this change in b64d39d8) such that the OOB data is
always copied into oobbuf and never appended to datbuf. Within U-Boot only
the nand_dump function (for the dump nand subcommand) was expecting the OOB
data to only be appended to datbuf. So we now change nand_dump to not
malloc extra space, correct the comment about datbuf and OOB data and switch
the pointer to oobbuf before printing.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The "nand info" and "nand device" now set shell/environment variables:
nand_writesize ... nand page size
nand_oobsize ..... nand oob area size
nand_erasesize ... nand erase block size
Also, the "nand info" command now displays this info.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: removed unnecessary memsets]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
These commands should work around various "hardware" ECC and BCH methods.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/]
Signed-off-by: Scott Wood <scottwood@freescale.com>
cmd_nand.c: In function ‘do_nand’:
cmd_nand.c:490:7: warning: variable ‘chip’ set but not used
[-Wunused-but-set-variable]
cmd_nand.c:489:7: warning: variable ‘part’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Rather than having a bunch of random commands handle autostart behavior,
unify the logic in a single place. This also fixes building of these
different commands when bootm is disabled.
Acked-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Grygorii Strashko
Mugunthan V N
Lothar Waßmann
Scott Wood
Tony Lindgren
Boris Brezillon
Max Krummenacher
Simon Glass
Heiko Schocher
Peter Tyser
Rostislav Lisovy
Pierre Aubert
Masahiro Yamada
Scott Wood
Sergey Lapin
Harvey Chapman
Tom Rini
Benoît Thébaudeau
Kim Phillips
Joe Hershberger
Thierry Reding
Steve Sakoman
Anatolij Gustschin
Marek Vasut
Marek Vasut
Mike Frysinger