Enable USB on all Amlogic Meson GXL based board.
Enable Regulator support on all boards.
Enable ADC support on the LibreTech-CC board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SARADC driver was merged after the following commit :
commit d35812368a ("regmap: change regmap_init_mem() to take ofnode instead udevice")
Thus breaking build, this patch fixes the regmap_init_mem accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
BOOT2 partition is empty and free for using to store the environment.
Use that instead of the default user partition.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The ARM64 has 2 MiB alignment requirement for the kernel. When using
fitImage, this requirement may by violated, the kernel will thus be
executed from unaligned address and fail to boot. Do what booti does
and run booti_setup() for kernel_noload images on arm64 to obtain a
suitable aligned address to which the image shall be relocated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Add option to the booti_setup() which indicates to it that the caller
requires the image to be relocated to the beginning of the RAM and
that the information whether the image can be located anywhere in RAM
at 2 MiB aligned boundary or not is to be ignored. This is useful ie.
in case the Image is wrapped in another envelope, ie. fitImage and not
relocating it but moving it would corrupt the envelope.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-By: Bin Chen <bin.chen@linaro.org>
At present the code overruns the bar[] array. Fix this.
At the same time, drop the leading / from the "/spl" path so that we can
run U-Boot SPL with:
spl/u-boot-spl
rather than requiring:
/path/to/spl/u-boot-spl
Reported-by: Coverity (CID: 131199)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
The current code might succeed on the first allocation and fail on the
second. Separate the checks to avoid this problem.
Of course, free() will never fail and the chances that (when allocating
two small areas) one will succeed and one will fail are just as remote.
But this keeps coverity happy.
Reported-by: Coverity (CID: 131226)
Signed-off-by: Simon Glass <sjg@chromium.org>
This loop never actually exits, but the way the code is written this is
not obvious. Add an explicit error check.
Reported-by: Coverity (CID: 131280)
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add explicit init of region to NULL per LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The latest ATF puts the U-Boot at 0x50000000, just like on all the other
boards. Adjust the text base to reflect that change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The sh_pfc_{read,write}() must operate on the register address directly
rather than on an offset, fix this to prevent illegal access.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both putc() and puts() can be called before global_data is set up. Some of
the code paths don't handle this correctly. Add an explicit test before
any member is accessed.
Reported-by: Coverity (CID: 169030)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There are multiple GPIO banks with up to 32 pins / bank. When
using 'gpio status -a' to read the pins, this patch displays
both GPIO<bank>_<index> similar to how the device trees
display in addition to displaying gpio_#
Signed-off-by: Adam Ford <aford173@gmail.com>
When CMD_GPIO is enabled the command 'gpio status -a' can cause
a hang or reboot if GPIO banks are not enabled, because it scans
all banks. This patch enables all GPIO banks so 'gpio status -a'
can fully execute.
Signed-off-by: Adam Ford <aford173@gmail.com>
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d0 ("block: Have BLOCK_CACHE default to y in some cases")
Signed-off-by: Adam Ford <aford173@gmail.com>
When an exception or interrupt occurs the link register (LR) may
contain the source of the exception, although we do not print the
value it may still be extracted with a debugger. When in SPL we
loop on getting and exception, but use a linking branch, which
over-writes the LR value, use a regular branch instruction here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This is the case when reading freshly created filesystem.
The error message is like the following:
btrfs_read_superblock: No valid root_backup found!
Since the data from super_roots/root_backups is not actually used -
decided to rework btrfs_newest_root_backup() into
btrfs_check_super_roots() that will only check if super_roots
array is valid and correctly handle empty scenario.
As a result:
* btrfs_read_superblock() now only checks if super_roots array is valid;
the case when it is empty is considered OK.
* removed root_backup pointer from btrfs_info,
which would be NULL in case of empty super_roots.
* btrfs_read_superblock() verifies number of devices from the superblock
itself, not newest root_backup.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow Linux commit 1377dd3e2987 (".gitignore: sort normal pattern
rules alphabetically").
This would allow us to easily catch duplicated patterns if any.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Replace Mateusz as Maintainer for ARM Snapdragon arch.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Acked-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add dump trace command which dump all trace
buffer content in a much more readable fashion
than md.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The header definitions are needed for reading
record information in cmd/iotrace.c
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Run AVB 2.0 full verification chain, avb verify
2. Check if 'avb get_uuid' works, compare results with
'part list mmc 1' output
3. Test `avb read` commands, which reads N bytes from a partition
identified by a name
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Add vbmeta partition info to android partition layout for TI
platforms.
2. Add support of AVB 2.0 (including avb subset of commands) for am57xx HS
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
[trini: Move to include/environment/ti/boot.h, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
1. Add initial support of boot states mode (red, green, yellow)
2. Add functions for enforcing dm-verity configurations
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
avb init - initialize avb2 subsystem
avb read_rb - read rollback index
avb write_rb - write rollback index
avb is_unlocked - check device lock state
avb get_uuid - read and print uuid of a partition
avb read_part - read data from partition
avb read_part_hex - read data from partition and output to stdout
avb write_part - write data to partition
avb verify - run full verification chain
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tom Rini
Neil Armstrong
Beniamino Galvani
Ramon Fried
Michal Simek
Marek Vasut
Simon Glass
Marek Vasut
Adam Ford
Andrew F. Davis
Alex Kiernan
Yevgeny Popovych
Masahiro Yamada
Chris Packham
Igor Opaniuk