Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common gpio code provides a function for handling the spi boot
workaround logic, so switch over to that rather than bang on the
gpio MMRs directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While the initdram() function makes sense on some arches, it doesn't for
Blackfin systems as it's always implemented the same way.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Import the is_valid_ether_addr() function from the Linux kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The DEBUG code in initdram() is quite old and was never really useful, so
just drop it altogether. Common Blackfin debug code does a better job.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added board_eth_init() function to bf537-stamp board.
Removed initialization for the Blackin EMAC driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory. phys_size_t is defined as an unsigned long on almost
all current platforms.
This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram). It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.
Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Stop tying things to the processor that should be tied to other defines and
change BFIN_CPU to CONFIG_BFIN_CPU so that it can be used in the build
system to select the -mcpu option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This moves the Blackfin-common bootldr command out of the BF537-STAMP
specific board directory and into the common directory so that all Blackfin
boards may utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Andreas Schallenberg
Mike Frysinger
Jean-Christophe PLAGNIOL-VILLARD
Ben Warren
Becky Bruce
Wolfgang Denk
Jon Loeliger
Jon Loeliger
Aubrey Li