These are library functions used by ARC700 architecture.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
These are header files used by ARC700 architecture.
Also note that "arch-arc700/hardware.h" is only required for compilation of
"designware_i2c" driver which refers to "asm/arch/hardware.h".
It would be good to fix mentioned driver sometime soon but it will cause
changes in ARM board configs that use "designware_i2c".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
This patch modifies envs to enable dual kernel boot
- with separated DTB if the DTB file is loaded successfully;
- with DTB apppended to uImage if DTB file is not found;
This is neccesssary for backward compatibilty.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch sets envs that describe board information.
The following envs are set: soc_id, soc_rev, board_rev.
Based on this information, if CONFIG_OF_LIBFDT is enabled,
the 'fdtfile' env is set as:
fdtfile=${soc_family}${soc_id}-${board}.dtb
The generated envs are intenionally not saved to persistent storage.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds s5p_cpu_rev.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to read cpu revision on Exynos CPU.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When ARCH_DMA_MINALIGN is greater than header size of the bit file, and buf is
not aligned, new_buf address became greater then buf_start address and the
load_word loop corrupts bit file data.
A work around is to decrease new_buf of ARCH_DMA_MINALIGN, it might corrupt data
before buf but permits to load correctly.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch fix the u-boot shell problem on TRATS2 board.
- If hold the key while booting is in progress,
white spaces are written in u-boot shell.
Set Automatically clears after resetting Rx FIFO.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Because of the list of peripherals is not sequential,
such a routine does not check for valid correctly.
Error check will be done when call the exynos_pinmux_config function.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
describe a set of default features that distros can rely on being available.
having this common definition means that distros can easily support systems
implementing them.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
People who write (or scripts that auto-generate) extlinux.conf don't
want to know about HW-specific information such as FDT filenames. Create
a new extlinux.conf tag "fdtdir" that specifies only the directory where
FDT files are located, and defer all knowledge of the filename to U-Boot.
The algorithm implemented is:
==========
if $fdt_addr_r is set:
if "fdt" tag was specified in extlinux.conf:
load the FDT from the filename in the tag
else if "fdtdir" tag was specified in extlinux.conf:
if "fdtfile" is set in the environment:
load the FDT from filename in "$fdtfile"
else:
load the FDT from some automatically generated filename
if no FDT file was loaded, and $fdtaddr is set:
# This indicates an FDT packaged with firmware
use the FDT at $fdtaddr
==========
A small part of an example /boot/extlinux.conf might be:
==========
LABEL primary
LINUX zImage
FDTDIR ./
LABEL failsafe
LINUX bkp/zImage
FDTDIR bkp/
==========
... with /boot/tegra20-seaboard.dtb or /boot/bkp/tegra20-seaboard.dtb
being loaded by the sysboot/pxe code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The specification for extlinux.conf[1] states that "fdt" is an alias for
"devicetree". To date, U-Boot only implements "fdt". Rectify that.
[1] http://freedesktop.org/wiki/Specifications/BootLoaderSpec/
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Command provides just dump subcommand for showing clock
frequencies in a soc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fix the timeout issue after running "bootp" command in U-Boot console.
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Alexey Brodkin
Aaron Wu
Sonic Zhang
Bob Liu
Piotr Wilczek
Tom Rini
Michal Simek
Novasys Ingenierie
Marek Vasut
Lukasz Majewski
Inha Song
Minkyu Kang
Dennis Gilmore
Stephen Warren
Jim Lin