This fixes a bug that tmp environment memory not being released.
Signed-off-by: Derek Ou <dou@siconix.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Modified mii_init to support boards with PHYs that are not set to
autonegotiate, but still want to use u-boot's mii commands to probe
the smi bus. Such PHYs will not set the Autonegotiate-done bit.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Applied the patch for baudrate divider value truncation for
serial_init to serial_setbrg as well.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Cleanup for M5271EVB:
Added clarification on the use of CONFIG_SYS_CLOCK.
Modified to use u-boot's HUSH parser.
Cleanup on environment settings.
Removed compiler warning by defining CONFIG_SYS_CS0_*
Dependencies:
Added the use of CONFIG_SYS_MCF_SYNCR for clock multiplier.
This depends on a patch to include/asm-m68k/m5271.h
that defines the multiplier and divider ratios.
Removed the definition of CONFIG_SYS_FECI2C.
This depends on a patch that removes the use of it in
cpu/mcf52x2/cpu_init.c
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
M5271 dynamic clock multiplier. It is currently fixed at 100MHz.
Allow the board header file to set their own multiplier and divider.
Added the #define for the multiplier and divider to the cpu header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Discontinue the use of CONFIG_SYS_FECI2C (only used by M5271EVB).
Use read-modify-write to activate the FEC pins without disabling I2C.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
CONFIG_M68K bdinfo cleanup:
Fixed compiler warning about baudrate printing.
format '%d' expects type 'int', but argument 2 has type 'long unsigned int'.
Added printing of "cpufreq"
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Added the CONFIG_M5271 to the list of Coldfire V2 processor. This
was causing the bus clock (not CPU clock) to be declared twice as
fast as it actually is. This causes UARTS to operate at half the
specified baudrate.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
On some platforms PCIE support is not required, but would be included
because the cpu supports it. To reduce fooprint it is now configurable
via CONFIG_PCI_DISABLE_PCIE.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the fdt UART clock fixup code to
only touch CPU internal UARTs on 4xx systems.
Only these UARTs are definitely clocked by gd->uart_clk.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the default SPI CS that we boot from into common code so that it can
be used in other SPI drivers and environment settings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Previously, booting over the UART required the baud rate to be known ahead
of time. Using a bit of tricky simple math, we can calculate the new board
rate based on the old divisors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Newer Blackfin boot roms support using the fast SPI read command rather than
just the slow one. If the functionality is available, then use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some bits of the DDR MMRs should not be set. If they do, bad things may
happen (like random failures or hardware destruction).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin's have an on-chip rom with a syscontrol() function that needs
to be used to properly program the memory and voltage settings as it will
include (possibly critical) factory tested bias values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):
./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Stefan Roese <sr@denx.de>
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.
Signed-off-by: Stefan Roese <sr@denx.de>
include/flash.h was commented to say that the address in
flash_info->start was a physical address. However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address. So I corrected the
comment to indicate that this was a virtual address.
The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver. However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places. I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls. The code is now consistent.
The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Original patch from Ralph Kondziella
plus clean up by Wolfgang Denk
plus changes by John Rigby
use ips clock not lpc
port forward to current u-boot release
Signed-off-by: Ralph Kondziella <rk@argos-messtechnik.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: John Rigby <jrigby@freescale.com>
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Add support for using a bmp other than
FSL_Logo_BMP for the DIU splash screen.
Can now set the env var "diu_bmp_addr" to
the address of a BMP in flash to use instead
of the default FSL_Logo_BMP.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Somehow I missed the real driver part in my last patch version. This patch
now adds the driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This is a port of the Linux Blackfin on-chip SDH driver to U-Boot.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Knowing the booting source of the part is useful, especially when the part
can switch dynamically between sources.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Set the default CONFIG_ENV_SPI_CS value to match the SPI CS that is used by
the Blackfin on-chip bootrom to boot out of SPI flash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is a port of the Linux Blackfin on-chip ATAPI driver to U-Boot.
Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the -mno-fdpic flag so that any Blackfin toolchain can be used to build
up u-boot, including ones that output FDPIC ELF by default.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than using 8bit transfers for everything, use 8/16/32 bit transfers
as usable with the source/destination addresses and the count size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The performance difference from doing an 8 bit DMA memcpy vs an optimized
core memcpy can be pretty big when you add in the overhead of setting up the
MDMA registers, cache flushes, etc... So only use dma_memcpy() when we
actually require it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We have to make sure the DMA channel is actually disabled in hardware before
attempting to reprogram it. Otherwise the new settings are ignored and we
end up with random hangs/failures.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Take the cache flush functions from the kernel as they use hardware loops in
order to get optimal performance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For systems with CONFIG_NET_MULTI disabled, bi_enetaddr does not get setup
based on $ethaddr, so set it up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Calculating the clocks requires a bit of calls to gcc math functions, so
cache the values after the first run since they'll most likely never
change once U-Boot is up and running.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start building all Blackfin boards with -ffunction-sections/-fdata-sections
and linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
derek@siconix.com
Richard Retanubun
Dirk Eibach
Matthias Fuchs
Mike Frysinger
Stefan Roese
Becky Bruce
Wolfgang Denk
Ralph Kondziella
Martha Marx
John Rigby
Remy Bohmer
Cliff Cai
Sonic Zhang