The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
For some reason the CLKDIV field varies between SoC in how it interprets
the bit values.
All 83xx and early (e500v1) PQ3 devices support:
clk/2: CLKDIV = 2
clk/4: CLKDIV = 4
clk/8: CLKDIV = 8
Newer PQ3 (e500v2) and MPC86xx support:
clk/4: CLKDIV = 2
clk/8: CLKDIV = 4
clk/16: CLKDIV = 8
Ensure that the MPC86xx and MPC85xx still get the same behavior and make
the defines reflect their logical view (not the value of the field).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash
via the 'nand' command.
Previously, the XPedite5370's NAND chip selects were properly
configured, but NAND support was not enabled.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Note that recent Linux kernels for the 85xx and 86xx map greater than
16MB of memory on bootup, but we use 16MB to maintain compatibility with
older Linux kernels for now.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly
improve NOR flash write speeds
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Peter Tyser
Kumar Gala
Poonam Aggrwal
Mike Frysinger