Beaglebone Board can be connected to expansion boards to add devices to them.
These expansion boards are called 'capes'. This patch adds support for
following versions of Beaglebone(AM335x) NAND capes
(a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64
(b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224
Further information and datasheets can be found at [1] and [2]
* How to boot from NAND using Memory Expander + NAND Cape ? *
- Important: As BOOTSEL values are sampled only at POR, so after changing any
setting on SW2 (DIP switch), disconnect and reconnect all board power supply
(including mini-USB console port) to POR the beaglebone.
- Selection of ECC scheme
for NAND cape(a), ROM code expects BCH8_HW ecc-scheme
for NAND cape(b), ROM code expects BCH16_HW ecc-scheme
- Selction of boot modes can be controlled via DIP switch(SW2) present on
Memory Expander cape.
SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB
SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2)
So to flash NAND, first boot via MMC or other sources and then switch to
SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
- For NAND boot following switch settings need to be followed
SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected )
SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- )
SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- )
SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- )
SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- )
SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device )
SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM )
SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device )
SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- )
[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion
[2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module
*IMPORTANT NOTE*
As Beaglebone board shares the same config as AM335x EVM, so following
changes are required in addition to this patch for Beaglebone NAND cape.
(1) Enable NAND in am335x_beaglebone board profile
(2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because:
- AM335x EVM has NAND device with datawidth=8, whereas
- Beaglebone NAND cape has NAND device with data-width=16
Emails to the board maintainer
"Rishi Bhattacharya <rishi@ti.com>"
have been bouncing.
Tom suggested to remove this board.
Remove also omap1510_udc.c because this is the last board
to enable it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
It's convenient to hold configurations for DDR3 PHY and EMIF in
separate common place. This patch moves K2HK DDR3 PHY and EMIF
configuration data with different rates and memory size to a common
ddr3_cfg.c file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This patch moves K2HK board directory to a common Keystone II board
directory. The Board related common functions are moved to a common
keystone board file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With latest v3.13 kernel, unitrd dt fixup is not needed. However for
older kernel versions such as v3.8/v3.10, it is needed. So to work
with both, add a u-boot env variable that can be set to do dt fixup
for older kernels.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Use KS2_ prefix in all definitions, for that replace K2HK_ prefix and
add KS2_ prefix where it's needed. It requires to change names also
in places where they're used. Align lines and remove redundant
definitions in kardware-k2hk.h at the same time.
Using common KS2_ prefix helps resolve redundant redefinitions and
adds opportunity to use KS2_ definition across a project not thinking about
what SoC should be used. It's more convenient and we don't need to worry
about the SoC type in common files, hardware.h will think about that.
The hardware.h decides definitions of what SoC to use.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The SoC related common functions in board.c should be placed to
a common keystone.c arch file.
Acked-by: Murali Karicheri <m-maricheri2@ti.com>
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
It's convinient to hold ddr3 function definitions in separate file
such as ddr3.h. So move this from hardware.h to ddr3.h.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers. Upon further inspection these
had been touching reserved fields (and having no impact). These came in
from historical bring-up code and can be discarded. Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.
Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
Add script to automate NAND flash process. As for now the board has
two burn scripts - burn to boot from SPI NOR flash and burn to boot
from AEMIF NAND flash, rename burn_uboot script to burn_uboot_spi.
Also update README to contain NAND burn U-boot process description.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Boot failures have been discovered due to a combination of routing issues and
non optimal ddr3 timings in the EMIF
* Since ddr3 timings are different after significant board layout changes
different timings are required for alpha, beta and production boards.
Signed-off-by: Franklin S. Cooper Jr <fcooper@ti.com>
J6 EVM can be built with UART3 as console, but currently
there's nothing muxing UART3 correctly. Likely this only
works because, based on commit log, author was only testing
with UART3 boot and - I assume - ROM code leave UART3 correctly
muxed in that case.
If we want to boot from MMC and still use UART3 as console,
then we need to mux those signals correctly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM437x Starter Kit has a qspi flash and gbit ethernet
support. By muxing those signals, we can use those
interfaces from u-boot.
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when porting u-boot to a new am43xx board, it
helps to know the name of the current unsupported
board so we don't have to hunt for design documents
to figure out what's written in the EEPROM.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
This should include the hash so that image_binary_size is really at the
end of the image, and not some 300 bytes earlier.
Signed-off-by: Simon Glass <sjg@chromium.org>
This family is supported by the TPS65218 PMIC. Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).
Signed-off-by: Tom Rini <trini@ti.com>
The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices. As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.
Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
We use the same variable as a3m071 in the environment to determine if we
should boot into Linux or U-Boot. This is useful on boards like
Beaglebone Black or AM335x GP EVM where we have persistent storage for
the environment.
Signed-off-by: Tom Rini <trini@ti.com>
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Signed-off-by: Nishanth Menon <nm@ti.com>
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Signed-off-by: Nishanth Menon <nm@ti.com>
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
If we build this function in cases where we would be discarding it
anyhow we still end up with maybe unused warnings. Rather than litter
the function with __maybe_unused, just spell out when to build it.
Signed-off-by: Tom Rini <trini@ti.com>
Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD
registers.
In EMIF_PHY_CTRL:
Updating [4:0]READ_LATENCY to 8, because at higher frequencies like
400MHz the read latency expected will be CL+3 as per tests from HW
folks.
Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug
purpose. With out this resume is not working(Still waiting for PHY team
to come back for better explanation).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also correct the bit masking of mac id read from the efuse.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
NAND boot mode on AM335x EVM has been verified, and steps
to use it has been documented and update in this README
Signed-off-by: Pekon Gupta <pekon@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Tom Rini <trini@ti.com>
pekon gupta
Masahiro Yamada
Hao Zhang
Murali Karicheri
Khoronzhuk, Ivan
Tom Rini
Mugunthan V N
Lokesh Vutla
Cooper Jr., Franklin
Felipe Balbi
Simon Glass
Sourav Poddar
Albert ARIBAUD
Vitaly Andrianov
Nishanth Menon
Wolfgang Denk
Andreas Färber