The AM572x-IDK board (Industrial Dev Kit) is a board based on TI's AM5728x
SOC which has a dual core 1.5GHz A15 processor. This board is a development
platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5728
NOTE: DT support is still pending upstream kernel acceptance but we
should be able to get the base system support with this patch.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.
"omap_hwmod: dcan1: _wait_target_disable failed"
This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.
The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.
DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[trini: s/PULLUP/PULL_UP/ based on DRA7xx EVM version of this patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
UART3 RX and TX pins are now moved to support uart download capability
on the platform. Old pins are now GPIOs routed to expansion ports.
All original boards should either have been returned for modifications
or already modified for the required change and maintaining
compatibility for older boards are no longer needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Steve Kipisz
Cooper Jr., Franklin
Roger Quadros
Lokesh Vutla
Felipe Balbi