We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Upon further review when populating README.scrapyard, d2net_v2 is a
variant on net2big_v2 and not just an orphan config. To help in the
future also add this to board/LaCie/net2big_v2/MAINTAINERS which needed
a little consolidation anyhow.
This reverts commit 1363740e79.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The command miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr) always
returns 8 for the PHY address. It is the reset value for the PHY
Address Register. Obviously, this default value could be incorrect.
Moreover, as the PHY address is well known, there is no need to
auto-detect it.
Now, the PHY address must given as a parameter to the PHY initialization
function. Additionally this patch also fixes some aesthetic issues.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
With the new second save argument introduced by the previous patch, all
the calls to the function had to be fixed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch groups together all the common functions for LaCie boards:
Ethernet PHY and MAC address initializations.
Moreover the configurations for LaCie Kirkwood boards are merged into
a single file: include/configs/lacie_kw.h
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch adds support for the LaCie 2Big Network v2 board, based on
the Marvell Kirkwood 6281 SoC.
Additional information is available at:
http://lacie-nas.org/doku.php?id=2big_network_v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Simon Glass
Tom Rini
Stefan Roese
Masahiro Yamada
Wolfgang Denk
Simon Guinot
Anatolij Gustschin
Albert ARIBAUD
Valentin Longchamp