Turn on generic board for the integrators, as per the request in
the startup message. Everything just works, tested on the
Integrator/AP and Integrator/CP.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
With CONFIG_SYS_GENERIC_BOARD the board hangs after issuing a 'save' command.
Remove CONFIG_SYS_GENERIC_BOARD until this issue can be fixed properly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since snow has a different memory configuration than peach, split the
configuration between the 5250 and 5420. Exynos 5420 supports runtime
memory configuration detection, and can make the determination between 4
and 7 banks at runtime.
Include the bank size with the number of banks for context to make the
number of banks meaningful.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Right now USB booting is enabled for Exynos5250 only. Moving all the
configs for USB boot mode from exynos5250-dt.h to exynos5-dt.h in order
to enableUSB booting for all Exynos5 SoCs.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Max footprint for SPL in both Exynos 5250 and 5420 is limited to 14 KB.
For Exynos5250 we need to keep it 14 KB because BL1 supports only fixed
size SPL downloading. But in case of Exynos5420 we need not restrict it
to 14 KB. And also, the SPL size for Exynos5420 is expected to increase
with the upcoming patches and the patches under review right now.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently environment resides at the location where BL2 ends.
This may hold good in case there is an empty space at this
position. But what if this place already has a binary or is
expected to have one. To avoid such scenarios it is better
to save environment at the end of the flash.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit
line of devices, there could be other boards using the same chip, so a
common configuration file is being added (exynos5420.h) as well
as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi).
The peach board as declared in boards.cfg is a copy of smdk5420
declaration. The configuration files are similar, but define different
default device trees, console serial ports and prompts.
The device tree files for smdk5420 and peach-pit inherit from the same
common file.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The u-boot Overo board actually supports both Overo (OMAP35xx)
and Overo Storm (AM/DM37xx) COMs with a range of different expansion
boards. This provides a mechanism to select the an appropriate device
tree file based on the processor version and, if available, the
expansion board ID written on the expansion board EEPROM. To match the
3.15+ kernels, fdtfile names have this format:
"omap3-overo[-storm]-<expansion board name>.dtb"
By default, we use "omap3-overo-storm-tobi.dtb".
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Conflicts:
include/configs/omap3_overo.h
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
During bootm/z, U-Boot relocates the DTB and initrd to high memory so
they are out of the way of the kernel. On ARM at least, some parts of
high memory are "highmem" and can't be accessed at early boot. To solve
this, we need to restrict this relocation process to use lower parts of
RAM that area accessible.
For the DTB, an earlier patch of mine set CONFIG_SYS_BOOTMAPSZ. However,
since some platforms have different restrictions on DTB and initrd
location, that config option doesn't affect the initrd. We need to set
the initrd_high environment variable to control the initrd relocation.
Since we have carefully chosen the load addresses for the DTB and
initrd (see comments in include/configs/tegraNNN-common.h re: values in
MEM_LAYOUT_ENV_SETTINGS), we don't actually need any DTB or initrd
relocation at all. Skipping relocation removes some redundant work.
Hence, set both fdt_high and initrd_high to ffffffff which completely
disables relocation.
If the user does something unusual, such as using custom locations for
the DTB/initrd load address or wanting to use DTB/initrd relocation for
some reason, they can simply set these variables to custom values to
override these environment defaults.
With this change, cmd_sysboot works correctly for a filesystem created
by the Fedora installer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
extlinux.conf is stored in /boot/extlinux/extlinux.conf rather than
/boot/extlinux.conf. Adjust Tegra's default boot scripts to use the
correct location. This change aligns Tegra's boot scripts with rpi_b.h
and also the location that the Fedora installer actually puts the file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We don't make use of the device tree otherwise yet (and will need to
think how to not break the current multi-board support) and this causes
further breakage with additional changes.
Signed-off-by: Tom Rini <trini@ti.com>
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Revert changes in iocon.h config file caused by
these two commits:
"configs: iocom: Fix typo on CMD_FPGA command"
(sha1: d0db28f940)
and
"fpga: Guard the LOADMK functionality with CMD_FPGA_LOADMK"
(sha1: 64e809afea)
CONFIG_CMD_FPGAD is own command.
Reported-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to run 'usb start' as preboot command so that ethernet comes up
during u-boot prompt.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Up till now goni's configuration has been stored at OneNAND. Since u-boot
itself is now stored at eMMC it is more handy to store envs there as well.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When building a target with CONFIG_ENV_IS_IN_SPI_FLASH the following
warning is seen:
include/configs/mx28evk.h:73:0: warning: "CONFIG_ENV_SIZE" redefined [enabled by default]
Protect the definition of CONFIG_ENV_SIZE to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The name of the dtb file used in the kernel is 'imx6dl-riotboard.dtb', so fix
it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
mars and riot boards use UART2 as console, so CONFIG_CONSOLE_DEV should point
to 'ttymxc1' instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
Commit e9fd66defd (ARM: mx6: define CONFIG_ARM_ERRATA_742230) enables
errata 742230 for imx6, because it helps remove one reboot issue.
However, this errata does not really apply on imx6, because Cortex-A9
on imx6 is r2p10 while the errata only applies to revisions r1p0..r2p2.
At a later time, commit f71cbfe3ca (ARM: Add workaround for Cortex-A9
errata 794072) adds support of errata 794072, which applies to all
Cortex-A9 revisions. As the workaround for both errata are exactly
same, it makes a lot more sense to select 794072 instead of 742230 for
imx6. Since we already enable 794072 for imx6, it's time to drop
errata 742230 to avoid confusion.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD for the Ethernut 5 board.
Signed-off-by: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The current size of 1MB is not enough use to use DFU. Increase it for
ARMv7 boards, all of which should have 32MB or more SDRAM.
With this change it is possible to do 'dfu mmc 0' on a Beaglebone Black.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
This family is supported by the TPS65218 PMIC. Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).
Signed-off-by: Tom Rini <trini@ti.com>
in almost all cases we need the i2c commands within the u-boot shell.
So we enable them within the common section.
Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
commit a0a37183bd "ARM: omap: merge GPMC initialization code for
all platform" needs CONFIG_NOR, CONFIG_NAND or CONFIG_CMD_ONENAND
to be set to access flash. Add CONFIG_NAND for tam3517 derived
boards to prevent the following error: "nand: error: Unable to
find NAND settings in GPMC Configuration - quitting"
cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Linus Walleij
Stephen Warren
Christian Riesch
Łukasz Dałek
Chin Liang See
Sergey Kostanbaev
York Sun
Darwin Rambo
Fabio Estevam
Heiko Schocher
Michael Pratt
Akshay Saraswat
Simon Glass
Ash Charles
Felipe Balbi
Khoronzhuk, Ivan
Stephen Warren
Jeroen Hofstee
Tom Rini
Michal Simek
Tushar Behera
Łukasz Majewski
Shawn Guo
Marek Vasut
Tim Schendekehl
Steve Rae
Chao Fu
Hannes Petermaier
Lokesh Vutla
WingMan Kwok