This adds PIC32 UART controller support based on driver model.
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In PIC32 GPIO controller is part of PIC32 pin controller.
PIC32 has ten independently programmable ports and each with multiple pins.
Each of these pins can be configured and used as GPIO, provided they
are not in use for other peripherals.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In PIC32 pin-controller is a combined gpio-controller, pin-mux and
pin-config module. Remappable peripherals are assigned pins through
per-pin based muxing logic. And pin configuration are performed on
specific port registers which are shared along with gpio controller.
Note, non-remappable peripherals have default pins assigned thus
require no muxing.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIC32 clock module consists of multiple oscillators, PLLs, mutiplexers
and dividers capable of supplying clock to various controllers
on or off-chip.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rather than passing the I/O port base address to the Super I/O code,
switch it to using outb such that it makes use of the I/O port base
address automatically.
Drop the extern keyword to satisfy checkpatch whilst here.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Set the I/O port base earlier, from board_early_init_f, in preparation
for it being used by the serial driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The existing mips_io_port_base variable isn't suitable for use early
during boot since it will be stored in the .data section which may not
be writable pre-relocation. Fix this by moving the I/O port base address
into struct arch_global_data. In order to avoid adding this field for
all targets, make this dependant upon a new Kconfig entry
CONFIG_DYNAMIC_IO_PORT_BASE. Malta is the only board which sets a
non-zero I/O port base, so select this option only for Malta.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
CONF_SLOWDOWN_IO is never set for any target, so remove the dead code in
the SLOW_DOWN_IO macro. This is done in preparation for changes to
mips_io_port_base which can be avoided in this path by removing it
entirely.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch makes sure that the flush/invalidate_dcache_range() functions
can handle corner-case calls like this -- invalidate_dcache_range(0, 0, 0);
This call is valid and is happily produced by USB EHCI code for example.
The expected behavior of the cache function(s) in this case is that they
will do no operation, since the size is zero.
The current implementation though has a problem where such invocation will
result in a hard CPU hang. This is because under such conditions, where the
start_addr = 0 and stop = 0, the addr = 0 and aend = 0xffffffe0 . The loop
will then try to iterate over the entire address space, which in itself is
wrong. But iterating over the entire address space might also hit some odd
address which will cause bus hang. The later happens on the Atheros MIPS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Fix 32 vs 64 bit load/store instructions. Access CP0_WATCHHI as
32 Bit register. Use 64 Bit register access for clearing gd_data
and copying U-Boot.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Argument boot_flags of board_init_f() should be set to 0 as
$a0 may be utilized in lowlevel_init() or mips_cache_reset()
or previous stage boot-loader.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Fix the lost dts info when merging patches.
Fix DSPI node for 'commit e0579a5852 ("armv8/ls1043aqds: add DSPI
support")' and QSPI node for 'commit 166ef1e90c ("armv8/ls1043aqds:
add QSPI support in SD boot")'.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update printf with dpbp_exit to match with previous function call.
Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All fields of struct dprc_cfg are not being configured while creating
child container. "Not" configured fields are assumed to be 0.
So memset dprc_cfg before configuring the fields.
Signed-off-by: Itai Katz <itai.katz@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Increase the kernel size supported for LS1021A platform. Define
CONFIG_SYS_BOOTM_LEN to 64M.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
kernel_size env variable is defined as 0x28000000, it is beyond NOR
flash range. Update kernel_size with 40MB kernel size.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On Novena, the DRAM SPD is connected to i2c1 while the Utility EEPROM
is connected to i2c3. Now that the EEPROM handling in U-Boot is fixed,
also fix this bit on Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Stefano Babic <sbabic@denx.de>
Android's tool chain enable the -mandroid at default.
This option will enable the -fpic, which cause uboot compilation
failure:
"
LD u-boot
u-boot contains unexpected relocations: R_ARM_ABS32
R_ARM_RELATIVE
"
In my testcase, arm-linux-androideabi-gcc-4.9 internally
enables '-fpic', so when compiling code, there will be
relocation entries using type R_ARM_GOT_BREL and .got
section. When linking all the built-in.o using ld, there
will be R_ARM_ABS32 relocation entry and .got section
in the final u-boot elf image. This can not be handled
by u-boot, since u-boot only expects R_ARM_RELATIVE
relocation entry.
arm-poky-linux-gnueabi-gcc-4.9 default does not enable '-fpic',
so there is not .got section and R_ARM_GOT_BREL in built-in.o.
And in the final u-boot elf image, all relocation entries are
R_ARM_RELATIVE.
we can pass '-fno-pic' to xxx-gcc to disable pic. whether
the toolchain internally enables or disables pic, '-fno-pic'
can work well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
"DISCARD" will remove ._secure.text relocate, but PSCI framework
has already used some absolute address those need to relocate.
Use readelf -t -r u-boot show us:
.__secure_start addr: 601408e4
.__secure_end addr: 60141460
60141140 00000017 R_ARM_RELATIVE
46 _secure_monitor:
47 #ifdef CONFIG_ARMV7_PSCI
48 ldr r5, =_psci_vectors
60141194 00000017 R_ARM_RELATIVE
6014119c 00000017 R_ARM_RELATIVE
601411a4 00000017 R_ARM_RELATIVE
601411ac 00000017 R_ARM_RELATIVE
64 _psci_table:
66 .word psci_cpu_suspend
...
72 .word psci_migrate
60141344 00000017 R_ARM_RELATIVE
6014145c 00000017 R_ARM_RELATIVE
202 ldr r5, =psci_text_end
Solutions:
1. Change absolute address to RelAdr.
Based on LDR (immediate, ARM), we only have 4K offset to jump.
Now PSCI code size is close to 4K size that is LDR limit jump size,
so even if the LDR is based on the current instruction address,
there is also have a risk for RelAdr. If we use two jump steps I
think we can fix this issue, but looks too hack, so give up this way.
2. Enable "DISCARD" only for CONFIG_ARMV7_SECURE_BASE has defined.
If CONFIG_ARMV7_SECURE_BASE is defined in platform, all of secure
will in the BASE address that is absolute.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add code to aid tracking down cache alignment issues.
In case DEBUG is defined in the cache.c, this code will
check alignment of each attempt to flush/invalidate data
cache and print a warning if the alignment is incorrect.
If DEBUG is not defined, this code is optimized out.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Some armv7 targets are missing a cache line size declaration.
In preparation for "arm: cache: Implement cache range check for v7"
patch, add these declarations with the appropriate value for
the target's SoC or CPU.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Restore the old behavior of the MMU section entries configuration,
which is without the S-bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Simon Glass <sjg@chromium.org>
The arch/arm/lib/cache-cp15.c checks for CONFIG_ARMV7 and if this macro is
set, it configures TTBR0 register. This register must be configured for the
cache on ARMv7 to operate correctly.
The problem is that noone actually sets the CONFIG_ARMV7 macro and thus the
TTBR0 is not configured at all. On SoCFPGA, this produces all sorts of minor
issues which are hard to replicate, for example certain USB sticks are not
detected or QSPI NOR sometimes fails to write pages completely.
The solution is to replace CONFIG_ARMV7 test with CONFIG_CPU_V7 one. This is
correct because the code which added the test(s) for CONFIG_ARMV7 was added
shortly after CONFIG_ARMV7 was replaced by CONFIG_CPU_V7 and this code was
not adjusted correctly to reflect that change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Simon Glass <sjg@chromium.org>
Enable this feature so that truetype fonts can be used on the sandbox
console. Update the tests to select the normal/rotated console when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
For testing it is useful to be able to select the font size and the console
driver for sandbox. Add this information to platform data and copy it to
the video device when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way for the video console driver to be selected. This is
controlled by the video driver's private data. This can be set up when the
driver is probed so that it is ready for the video_post_probe() method.
The font size is provided as well. The console driver may or may not support
this depending on its capability.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This is used by two of the font files. Add this license to permit tracking
of this. The copyright text cannot be added to the .ttf files, so put it
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This font is a little more ornate than normal. Example uses are on security
screens where a feeling of formality is required.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be used when a a friendly 'hand-writing' font is needed. It helps
to make the device feel familiar.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be used when a mono-space font is needed, but the console font
is too small (such as with high-DPI displays).
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing 8x16 font is adequate for most purposes. It is small and fast.
However for boot screens where information must be presented to the user,
the console font is not ideal. Common requirements are larger and
better-looking fonts.
This console driver can use TrueType fonts built into U-Boot, and render
them at any size. This can be used in scripts to place text as needed on
the display.
This driver is not really designed to operate with the command line. Much
of U-Boot expects a fixed-width font. But to keep things working correctly,
rudimentary support for the console is provided. The main missing feature is
support for command-line editing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
With proportional fonts the vidconsole uclass cannot itself erase the
previous character. Provide an optional method so that the driver can
handle this operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we start a new line (due to the user pressing return), signal this to
the driver so that it can flush its buffer of character positions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow the left margin to be set so that text does not have to be right up
against the left side. On some panels this makes it hard to read.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be sent when to many characters are entered. Make sure it is
ignored and does not cause a character to be displayed.
Signed-off-by: Simon Glass <sjg@chromium.org>
With anti-aliased fonts we need a more fine-grained horizontal position
than a single pixel. Characters can be positioned to start part-way through
a pixel, with anti-aliasing (greyscale edges) taking care of the visual
effect.
To cope with this, use fractional units (1/256 pixel) for horizontal
positions in the text console.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add rules to allow TrueType files to be compiled into U-Boot for use on
the video console.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a header file which provides a fairly light-weight TrueType
rendering implementation. It is pulled from http://nothings.org/. The code
style does not comply with U-Boot but I think it is best to leave alone to
permit the source to be synced later if needed.
The only change is to fix a reference to fabs() which should route through
a macro to allow U-Boot to provide its own version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow the env__dfu_configs boardenv data to specify the set of DFU
transfer sizes to test. Manually specifying test sizes is useful if you
wish to test multiple DFU configurations (e.g. SD card ext4 filesystem, SD
card whole raw partition, RAM, etc.), but don't want to test every
single transfer size on each, to avoid bloating the overall time taken by
testing. If the boardenv doesn't specify a set of sizes, the built-in list
is used as a default, preserving backwards-compatibility.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some unit tests expect the cwd of the sandbox process to be the root
of the source tree. Ensure that requirement is met.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is required for at least "ut dm" to operate correctly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tests can complete in passed, skipped, xpass, xfailed, or failed, states.
Currently the U-Boot log generation code doesn't handle the xfailed or
xpass states since they aren't used. Add support for the remaining states.
Without this, tests that xfail end up being reported as skipped.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Purna Chandra Mandal
Paul Thacker
Paul Burton
Marek Vasut
Daniel Schwierzeck
Qianyu Gong
Prabhakar Kushwaha
Alison Wang
Peng Fan
Wang Dongsheng
Albert ARIBAUD
Simon Glass
Tom Rini
Stephen Warren