I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
Put the version (and magic) after the HRCW. This puts it in a fixed
location in flash, not at the start of flash but as close as we can get.
Signed-off-by: Jerry Van Baren <vanbaren@cideas.com>
For better format and style, I streamlined the 83xx head files,
including immap_83xx.h and mpc83xx.h. In the old head files, 1)
duplicated macro definition appear in the both files; 2) the structure
of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The
macro definition put inside the each structure. So, I cleaned up the
structure of QE immr from immap_83xx.h, deleted the duplicated stuff and
moved the macro definition to mpc83xx.h, Just like MPC8260.
CHANGELOG
*streamline the 83xx immr head file
Signed-off-by: Dave Liu <daveliu@freescale.com>
The patch prevents the GCC tool chain from striping useful code for
optimization. It will make UEC ethernet driver workable, Otherwise the
UEC will fail in tx when you are using gcc4.x. but the driver can work
when using gcc3.4.3.
CHANGELOG
*Prevent the GCC from striping code for optimization, Otherwise the UEC
will tx failed when you are using gcc4.x.
Signed-off-by: Dave Liu <daveliu@freescale.com>
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
- fix logic error in image type handling
- make sure file system images (cramfs etc.) get stored in flash
with image header stripped so they can be mounted through MTD
Since the relocation fix is not included yet and we're not sure how
it will be added, this patch removes code that required relocation
to be fixed for now.
Signed-off-by: Stefan Roese <sr@denx.de>
As suggested by Grant Likely this patch enables the Xilinx SystemACE
driver to select 8 or 16bit mode upon startup.
Signed-off-by: Stefan Roese <sr@denx.de>
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
This patch enables the "new" get_dev() function for block devices
introduced by Grant Likely to be used on systems that still suffer
from the relocation problems (manual relocation neede because of
problems with linker script).
Hopefully we can resolve this relocation issue soon for all platform
so we don't need this additional code anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch switches to the desired I2C bus when the date/dtt
commands are called. This can be configured using the
CFG_RTC_BUS_NUM and/or CFG_DTT_BUS_NUM defines.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Signed-off-by: Stefan Roese <sr@denx.de>
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch is in preparation of additional changes to the sysace driver.
May as well take this opportunity to fixup the inconsistent whitespace since
this file is about to undergo major changes anyway.
There are zero functional changes in this patch. It only cleans up the
the whitespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Printing a buffer is a darn useful thing. Move the buffer print code
into print_buffer() in lib_generic/
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Change the xilinx device drivers and board code to include config.h
instead of xparameters.h directly. config.h always includes the
correct xparameters file. This change reduces the posibility of
including the wrong file when adding a new xilinx board port
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each of the filesystem drivers duplicate the get_dev routine. This change
merges them into a single function in part.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update / extend Software Update Mechanism for MCC200 board:
- Add support for rootfs image added. The environment variables
"rootfs_st" and "rootfs_nd" can be used to override the default
values of the image start and end.
- Remove excessive key check code.
- Code cleanup.
Some boards that can have more than 768MBytes of SDRAM need to
set "initrd_high", so that the initrd can be accessed by the
Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
Previously the strapping DCR/SDR was read to determine if the internal PCI
arbiter is enabled or not. This strapping bit can be overridden, so now
the current status is read from the correct DCR/SDR register.
Signed-off-by: Stefan Roese <sr@denx.de>
Paul Gortmaker
Sam Song
Jerry Van Baren
Dave Liu
Stefan Roese
Wolfgang Denk
Sergei Poselenov
Haiying Wang
Grant Likely
Gary Jennejohn
Bartlomiej Sieka