Add smc_write_hwaddr() to set mac address.
Clear dev before use.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch proposes to migrate the davinci_emac driver to using the
eth_device->write_hwaddr function pointer as suggested by Ben Warren.
All the davinci boards had the behaviour, prior to this patch, of
sync'ing the environment variable enetaddr with the MAC address read
from non-volatile storage on boot -- when the two locations disagreed,
the environment variable value took precendence. This patch keeps the
same behaviour but lets eth_initialize take care of it.
This patch refactors davinci_emac setup in the boards so that the MAC
address is read from non-volatile storage into the environment variable
and then the environment variable value is use in eth_intialize. The
only exception is the direct call to davinci_eth_set_mac_addr made by
the da830evm board init which was changed into an assignment of the
enetaddr field.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Emaclite was using old net api that's why
this patch move emaclite to NET_MULTI api.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Most people don't use the 'rarpboot' command, so only enable it when
CONFIG_CMD_RARP is defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some boards need their board-specific PHY quirks to be called
to PHY to work normally. As mpc5xxx_fec driver uses on demand
PHY initialization and can even reinit PHY during normal operation
we can't count on reset_phy() call from arch/<arch>/lib/board.c
(it is most likely called _before_ we init the PHY from the
driver) so we need to add call to reset_phy() directly in the
driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some return values pretended correct pass. This patch changes them according
to README.drivers.net. This patch changes e.g. command 'dhcp' to stop after
errorneous autonegotiation.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch increases timeout for autonegotiation from 1 second to 3 seconds.
Some boards (e.g. at91rm9200ek) did not negotiate within 1 second.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
V3: further refinements:
- use priv member instead of container method
- allow setting of MAC address by write_hwaddr method
- avoid shutting down link between commands
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Instead of always performing an autoneg, check if the PHY
already has a link and if it matches one of the requested
modes. Initially only 100MbFD is optimized this way.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This udelay looks bogus and doesn't help my board.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
uec_init() adds an udelay(100000) even though
the PHY status read went well, don't do that.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.
Tested with ./MAKEALL ARM7 that both boards still compile.
Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The correct definition is in drivers/qe/uec.h so just
remove this one.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds the Numonyx manufacturer code (0x20) to
onenand manufacturers.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
CONFIG_ENV_SIZE does not need block alignment.
Document CONFIG_ENV_RANGE and CONFIG_ENV_OFFSET_OOB.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Consolidate some code in mtd_get_len_incl_bad(), and fix a condition
where a valid partition could be reported as truncated if it has a
good block at the end of the device (unlikely, since the BBT is usually
there).
Fix mid-block declarations in net_part_size().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
This patch adds a new 'mtdparts add' variant: add.spread. This command variant
adds a new partition to the mtdparts variable but also increases the partitions
size by skipping bad blocks and aggregating any additional bad blocks found at
the end of the partition.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
This patch introduces the 'spread' sub-command of the mtdparts command.
This command will modify the existing mtdparts variable by increasing
the size of the partitions such that 1) each partition's net size is at
least as large as the size specified in the mtdparts variable and 2)
each partition starts on a good block.
The new subcommand is implemented by iterating over the mtd device
partitions and collecting a bad blocks count in each -- including any
trailing bad blocks -- and then modifying that partitions's part_info
structure and checking if the modification affects the next partition.
This patch is based on a port of the 'dynnamic partitions' feature by
Harald Welte <laforge@gnumonks.org>; ported from commit
e05835df019027391f58f9d8ce5e1257d6924798 of
git://git.openmoko.org/u-boot.git. Whereas Harald's feature used a
compile-time array to specify partitions, the feature introduced by
this patch uses the mtdparts environment variable.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
This patch adds an additional column to the output of list_partitions. The
additional column will contain the net size and a '(!)' beside it if the net
size is not equal to the partition size.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
CC: Scott Wood <scottwood@freescale.com>
The logic to 'spread' mtd partitions needs to calculate the length in
the mtd device, including bad blocks.
This patch introduces a new function, mtd_get_len_incl_bad that can
return both the length including bad blocks and whether that length
was truncated on the device. This new function will be used by the
mtdparts spread command later in this series. The definition of the
function is #ifdef'd out in configurations that do not use the new
'mtdparts spread' command.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
The get_mtd_device_nm function is called in a couple places and the
string that is passed to it is not really used after the calls.
This patch regroups the calls to this function into a new function,
get_mtd_info.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Stefan Roese <sr@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Get rid of the several "#if 0" sections that were keeping around Linux
code that isn't relevant to U-Boot. Besides cluttering the code, these
sections make tracking upstream changes harder, rather than easier.
It's easy to discard obviously irrelevant diff hunks that patch rejects,
but it's not as easy to notice hunks that apply cleanly to the #if 0
section, but *are* relevant to U-Boot and require modification elsewhere.
Also remove suspend/resume, as this is not applicable to U-Boot. Removal
saves 232 bytes on powerpc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The dump command is made to increment its address on repeat,
as md does. Other commands do not make sense to issue repeatedly,
and can be irritating when it happens accidentally, so don't.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased. This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.
Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.
While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition. To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand. This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.
While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
- If the current device is overridden by a named partition,
- update the caller's pointer/index, rather than copy over the
nand_info struct, and
- be sure to call board_nand_select_device even when the device
is overridden by a named partition.
- Support 64-bit offsets/sizes in a few more places.
- Refactor arg_off_size for added readability and flexibility,
and some added checks such as partition size.
- Remove redundant check for bad subcommands -- if there's no match
it'll print usage when it gets to the end anyway.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
The underlying code in nand_base.c already supports non-page-aligned reads
and writes, but the block-skipping wrapper code did not.
With block skipping, an unaligned start address is not useful since you
really want to be starting at the beginning of a partition -- or at least
that's where you want to start checking for blocks to skip, but we don't
(yet) support that. So we still require the start address to be aligned.
An unaligned length, though, is useful for passing $filesize to the
read/write command, and handling it does not complicate block skipping.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Generalized misuse of ble within relocation and bss
initialization loops caused one iteration too many.
Instead of ble ('branch if lower or equal'), use
blo ('branch if lower').
While we're at it, fix all 'addreee' typos.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Freescale application note AN3638 describes an update to the NXID format,
which stores MAC addresses and related data on an on-board EEPROM. The new
version adds support for up to 23 MAC addresses, instead of just 8. Since
the initial implementation of NXID had a "0" in the 'version' field, this
new version is called "v1".
Boards that are shipped with EEPROMs in the NXID v1 format should define
CONFIG_SYS_I2C_EEPROM_NXID_1 instead of CONFIG_SYS_I2C_EEPROM_NXID.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
pumping line-rate traffic though a p4080 rev.2, which
is configured to encrypt packets prior to forwarding through
an IPsec tunnel, gets this error:
of_platform ffe302000.jq: DECO: desc idx 22: LIODN error. DECO was trying
to share from itself or from another DECO but the two Non-SEQ LIODN
values didn't match or the "shared from" DECO's Descriptor required that
the SEQ LIODNs be the same and they aren't.
Since high traffic rates cause DECOs to begin to start sharing
shared descriptors amongst themselves, and DECOs inherit job queue
LIODNs when accessing shared descriptors, and a recently discovered
rev.2 h/w erratum requires all sharing job queues in a partition
have same liodn assignment, reassign the first job queue's liodn
assignment to the rest.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We configure the controller but dont have virtual address space thus any
devices on the 4th controller are not accessible in u-boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Make the U-Boot update command sequence conditional. Helps prevent
accidental erasing if an upload or previous step fails
* Make it easier to update other FLASH banks
* Enable DDR controller cache line interleaving and bank cs0/cs1 by default
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the code which writes to the on-board EEPROM so that it can detect if
the write failed because the EEPROM is write-protected. Most of the 8xxx-class
Freescale reference boards use an AT24C02 EEPROM to store MAC addresses and
similar information. With this patch, if the EEPROM is protected, the
"mac save" command will display an error message indicating that the write
has not succeeded.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable half drive strength, set RTT to 60Ohm and set write leveling override.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original code maps boot flash as non-cacheable region. When calling
relocate_code in flash to copy u-boot from flash to ddr, every loop copy command
is read from flash. The flash read speed will be the bottleneck, which consuming
long time to do this operation. To resovle this, map the boot flash as
write-through cache via tlb. And set tlb to remap the flash after code
executing in ddr, to confirm flash erase operation properly done.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_ENV_SIZE of MPC8569MDS was wrongly set to CONFIG_ENV_SECT_SIZE which
is 128KB, so it took longer time to do crc32 calculation for ENV than it should
do. It causes the bootup for MPC8569MDS significantly slow. This patch fixs it
to 0x2000(8KB), also fix the comment for CONFIG_ENV_SECT_SIZE to correct size.
Signed-off-by: Kai.Jiang <Kai.Jiang@freescale.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot.bin can be loaded at any 4-byte aligned memory location and directly
'jumped' to using the 'go' command using the load address as the start
address. Doing so performs a 'warm boot' which skips memory initialisation
and other low-level initialisations, relocates U-Boot to upper memory and
starts U-Boot in RAM as per normal 'cold boot'
Provides a small speed increase and prepares for fully relocatable image.
Downside is the TEXT_BASE, bss, load address etc must ALL be aligned on a
a 4-byte boundary which is not such a terrible restriction as everything
is already 4-byte aligned anyway
Stephan Linz
Thomas Chou
Ben Gardiner
Michal Simek
Peter Tyser
Ilya Yanok
Andreas Bießmann
Reinhard Meyer
Joakim Tjernlund
Ben Warren
Reinhard Meyer (-VC)
Enric Balletbo i Serra
Scott Wood
Albert Aribaud
Wolfgang Denk
Timur Tabi
Kim Phillips
Kumar Gala
Emil Medve
Haiying Wang
Graeme Russ