DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.
Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.
Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Disable the warm reset and enable the cold reset for a more reliable
restart ('reset'). This is taken from the Linux kernel, see imx_src_init()
in arch/arm/mach-imx/src.c.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.
Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
mxc_get_clock's return type is unsigned int. 'return -1' is same with
'return 0xffffffff', so 0 should be used as the return value when
unsupported mxc_clock type is passed to mxc_get_clock.
Also include an err message when unsupported mxc_clock type is passed
to mxc_get_clock.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Add imx6 thermal device to mx6 soc file. Read the cpu temperature
using this device to access onchip thermal sensor.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Add api to check and enable pll3 as required
for thermal sensor driver.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.
SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.
The result is that the selected boot device is not used across all
the boot stages.
Update spl_boot_device() to look at gpr9 when necessary.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Include <asm/bootm.h> to see the prototype for get_board_rev()
and prevent warning "Should it be static?" with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Checking the pre_periph_clk_sel and pre_periph2_clk of CCM CBCMR
register, if the PLL2 PFD0 or PLL2 PFD2 is used for the clock source,
do not reset this PFD to avoid system hang. Customers may set this
in DDR script or use BT_FREQ to select low freq boot.
Signed-off-by: Ye.Li <B37916@freescale.com>
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Commit 224beb833e add clock
enabling function for FEC, but the masks are not available
for SX processor and the mx6sxsabresd cannot be built clean.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
The Latency parameters of PL310 Tag RAM latency control register and
Data RAM Latency control register are set in L2 cache enable. And
setting these registers must have PL310 NOT enabled.
But when using Plugin mode boot, the PL310 is enabled by bootrom.
The patch disables the PL310 before applying this setting.
Signed-off-by: Ye.Li <Ye.Li@freescale.com>
Current way of calculation CS0_END field for MMDCx_MDASP register
is problematic because in most cases the user is forced to define
cs_density in an unnatural way: as value - 2, instead of value.
This breaks the abstraction provided by struct mx6_ddr_sysinfo
because the user is forced to be aware of the way the calculation
is performed.
Refactor the calculation.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
According to MX6 TRM, both MMDC and DRAM should be configured to
the same powerdown precharge. Currently, mx6_dram_cfg()
configures MMDC for fast pd (MDPDC[7] = 0), and the DRAM for
'slow exit (DLL off)' (MR0[12] = 0).
Configure MMDC for slow pd.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Bit 16 in mapsr register is in a reserved field. Don't write to it.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The COL field value cannot be easily calculated from the desired
column number. Instead, there are special cases for that, see the
datasheet, MMDCx_MDCTL field description, field COL . Cater for
those special cases.
Signed-off-by: Marek Vasut <marex@denx.de>
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6solox is the newest member of the mx6 family.
Some of the new features on this variants are:
- Cortex M4 microcontroller (besides the CortexA9)
- Dual Gigabit Ethernet
Add the initial support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces
set_ldo_voltage() function that can be used to set the voltages
of any of the three LDO regulators controlled by the PMU_REG_CORE register.
Prior to this commit there was a single set_vddsoc() which only configured the
VDDSOC regulator.
Update the comments to align with the new set_ldo_voltage() implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do
the shift after the multiply to avoid rounding errors
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
According to:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0
ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b
newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:
i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison
With this change the secure boot status is correctly displayed
Signed-off-by: Stefano Babic <sbabic@denx.de>
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
imx_get_fecclk() returns enet_ref instead of ipg.
Since the clock is used to calculate the prescaler
for the MDIO interface wrong values can be calculated.
Tested on a custom MX6S board with 100MBit interface
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.
Report it as MX6D instead:
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2),
it will cause warm reset fail, need to clear this MMDC_CHx_MASK field
to make sure all the i.MX6 series SOCs reset function work. Otherwise,
uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.
Signed-off-by: Anson Huang <b20788@freescale.com>
For low freq boot mode(ARM boot up with 396MHz), ROM
will not set AHB clock to 132MHz, and the reset value of
AHB divider is incorrect which will lead to wrong AHB
rate, need to correct it. To enable low freq boot mode,
need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL
SabreSD board and i.MX6SL EVK board.
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Split the SATA clock enabling function and add PCI express clock
enabling function. The SATA clock enabling function starts up the
100MHz SATA reference PLL in ENET_PLL register, but the code can
be re-used to enable the 125MHz PCIe reference in ENET_PLL, so pull
this code into separate function. Moreover, add the PCIe clock
enabling code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Commit 022298278 (mx6: soc: Disable VDDPU regulator) is causing kernel hang
for people using FSL kernel 3.0.35 and 3.10, so revert it for now.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Reported-by: Pierre Aubert <p.aubert@staubli.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tim Harvey
Boris BREZILLON
Dirk Behme
Peng Fan
Ye.Li
Stefan Roese
Nikita Kiryanov
Nitin Garg
Jeroen Hofstee
Eric Nelson
Masahiro Yamada
Stefano Babic
Fabio Estevam
Nikolay Dimitrov
Ye.Li
Marek Vasut
Gabriel Huau
Heiko Schocher
Andre Renaud
Markus Niebel
Anson Huang