The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).
Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Replace hardcoded value with defined constant SECTOR_BYTES.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.
Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB
After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
The OMAPL138-LCD board uses a NAND chip with a 16 bits bus. Add
support into the davinci driver for 16 bit bus NAND chips.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the description of the Toshiba TC58NVG2S0H SLC nand to the nand_ids
table so we can use the NAND ECC infos and the ONFI timings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Clear ecc ON bit while sending read command as all types
of read command(like reading spare) doesnt need ECC to be
enabled. It has been anyway taken care in other places
whereever required using arasan_nand_enable_ecc().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the command buffer gets allocated with a size of 32 bytes.
This causes warning messages on systems with cache lines bigger than
32 bytes:
CACHE: Misaligned operation at range [9df17a00, 9df17a20]
Define command buffer to be at least 32 bytes, but more if cache
line is bigger.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data") the assignment of mtd->priv was removed
but was not replaced. This adds the required nand_set_controller_data()
call.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add a full-id entry for the H27QCG8T2E5R‐BCF NAND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
To support UBI in SPL we need a simple NAND read function. Add one to
nand_spl_simple and keep it as simple as it goes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This empty line should not be there. Remove it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND chips are supposed to expose their capabilities through advanced
mechanisms like READID, ONFI or JEDEC parameter tables. While those
methods are appropriate for the bootloader itself, it's way to
complicated and takes too much space to fit in the SPL.
Replace those mechanisms by a dumb 'trial and error' mechanism.
With this new approach we can get rid of the fixed config list that was
used in the sunxi NAND SPL driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Split the 'load page' and 'read page' logic in 2 different functions so
we can later load the page and test different ECC configs without the
penalty of reloading the same page in the NAND cache.
We also move common setup to a dedicated function (nand_apply_config()) to
avoid rewriting the same values in NFC registers each time we read a page.
These new functions are passed a pointer to an nfc_config struct to limit
the number of parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
check_value_xxx() helpers are using a 1ms delay between each test, which
can be quite long for some operations (like a page read on an SLC NAND).
Since we don't have anything to do but to poll this register, reduce the
delay between each test to 1us.
While we're at it, rename the max_number_of_retries parameters and the
MAX_RETRIES macro into timeout_us and DEFAULT_TIMEOUT_US to reflect that
we're actually waiting a given amount of time and not only a number of
retries.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Use CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND value instead of trying to guess
where the redundant u-boot image is based on simple (and most of the time
erroneous) heuristics.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
# Conflicts:
# drivers/mtd/nand/sunxi_nand_spl.c
On modern NAND it's more than recommended to have a backup copy of the
u-boot binary to recover from corruption: bitflips are quite common on
MLC NANDs, and the read-disturbance will corrupt your u-boot partitition
more quickly than what you would see on an SLC NAND.
Add an extra Kconfig option to specify the offset of the redundant u-boot
image.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[scottwood: added ifdef to fix build break]
Signed-off-by: Scott Wood <oss@buserror.net>
The SYS_NAND_U_BOOT_OFFS is quite generic, but the Kconfig entry is forced
to explicitly depend on platforms that are not already defining it in their
include/configs/<board>.h header.
Add the SYS_NAND_U_BOOT_LOCATIONS option, make the SYS_NAND_U_BOOT_OFFS
depends on it, remove the dependency on NAND_SUNXI and make it dependent
on SPL selection.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The sunxi SPL NAND controller driver supports use 'BootROM'-like configs,
that is, configs where the ECC bytes and real data are interleaved in the
page instead of putting ECC bytes in the OOB area.
Doing that has several drawbacks:
- since you're interleaving data and ECC bytes you can't use the whole page
otherwise you might override the bad block marker with non-FF bytes.
- to solve the bad block marker problem, the ROM code supports partially
using the page, but this introduces a huge penalty both in term of read
speed and NAND memory usage. While this is fine for rather small
binaries(like the SPL one which is at maximum 24KB large), it becomes
non-negligible for the bootloader image (several hundred of KB).
- auto-detection of the page size is not reliable (this is in my opinion
the biggest problem). If you get the page size wrong, you'll end up
reading data at a different offset than what was specified by the caller
and the reading may succeed (if valid data were written at this address).
For all those reasons I think it's wiser to completely remove support for
'syndrome' configs. If we ever need to support it again, then I'd recommend
specifying all the config parameters through Kconfig options.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This needs to be set to avoid a fatal error when ECC is used.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This uses the wrote base register value. Fix it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updates the NAND code to match Linux v4.6. The previous sync was from
Linux v4.1 in commit d3963721d9.
Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
This change is part of the Linux 4.6 sync. It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Commit ad4f54ea86 ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Scott Wood <oss@buserror.net>
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Andrey Yurovsky
Ladislav Michl
Jagan Teki
Fabien Parent
Boris Brezillon
Siva Durga Prasad Paladugu
Jagan Teki
Masahiro Yamada
Stefan Agner
Scott Wood
Chris Packham
Hector Palacios
Brian Norris
Thomas Gleixner
Sumit Garg
Robert P. J. Day
Andre Renaud
Max Krummenacher
Heiko Schocher
Marek Vasut
Lokesh Vutla
Peng Fan
Vagrant Cascadian
Purna Chandra Mandal
Graham Moore