The local functions in the mxs i2c driver are not marked static, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This algorithm computes the values of TIMING{0,1,2} registers for the
MX28 I2C block. This algorithm was derived by using a scope, but the
result seems correct.
The resulting values programmed into the registers do not correlate
with the contents in datasheet. When using the values from the datasheet,
the I2C clock were completely wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
The I2C block reset configures the I2C bus speed to strange value.
Read the I2C speed from the block before reseting the block and
restore it afterwards, so the I2C operates correctly. This issue
can be replicated by doing unsuccessful I2C transfer, after such
transfer finishes, the I2C block clock speed is misconfigured.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
According to FSL, the value in the TIMING2 register shall be 0x00300030
instead of what's written in the datasheet. This new value correlates
with older STMP36xx datasheet. Issues were detected in Linux when this
register was misconfigured, so write this correct value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver
to avoid duplication of code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch implements the setup and retrieval functions for the I2C
bus speed on the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch pulls out the I2C speed setup from the i2c_init() call
and implements the bus configuration lookup table with register
values that needs to be programmed into the I2C IP to run at
particular speed.
This patch is a first step towards implementing run-time I2C bus
speed configuration for the MXS I2C IP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Large EEPROMs, e.g. 24lc32, need 2 byte to address the internal memory.
These devices require that the high byte of the internal address has to be
written first.
The mxs_i2c driver currently writes the address' low byte first.
The following patch fixes the byte order of the internal address that should
be written to the I2C device.
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
CC: Marek Vasut <marex@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Wolfgang Denk
Marek Vasut
Otavio Salvador
Torsten Fleischer
Marek Vasut