The R40 has the CPUCFG block at the same address as the A20.
Fix it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can do DRAM initialization for the R40, we can enable
SPL support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO on the R40 SoC is mostly compatible with the A20.
Only a few pin functions for mmc2 were added to the PC
pingroup, to support 8 bit eMMCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO is generally compatible with the A20, except that it routes the
full 8 bits and eMMC reset pins for mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_MACPWR to Kconfig and update all the sunxi defconfigs
that used it in SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_SATAPWR into kconfig.
Thanks to that, many SYS_EXTRA_OPTIONS can be removed from some
defconfigs.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB_EHCI configuration is already set in this defconfig
using kconfig's config. This configuration in SYS_EXTRA_OPTIONS
must be removed and so the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This configuration is not necessary in a defconfig file so
it is removed from the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the AXP209_POWER option from SYS_EXTRA_OPTIONS.
As this configuration already exists on Kconfig, we just need
to remove it from defconfig.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
'A || (!A && B)' is equivalent to 'A || B'.
Let's reduce the complexity of the statement in start_jr0().
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After allocating sata->cmd_hdr_tbl_offset we have to check
this variable and not variable sata.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
(pdimm[0].data_width >= 32) || (pdimm[0].data_width <= 40)
is always true.
We should use && here.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The number of arguments for printf does not match the
format string.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If current_urb is NULL it should not be dereferenced.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If !parent, the changed line is not reached.
So there is no need to check the value again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If realloc fails we should release the old buffer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Each call of va_start must be matched by a call of va_end.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Linaro provides a number of pre-built GCC toolchains for both 32 and
64bit ARM. Switch to their 2017.02 release of gcc-6.3.1 for both.
Cc: Koen Kooi <koen.kooi@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Many toolchains for ARM use the 'gnueabihf' suffix rather than just
'gnueabi', so allow these to be used, but with a lower priority than
'gnueabi' ones.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These drivers have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
These commands have no user since commit ea3310e8aa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Handle symlinks to files in the current directory. Other cases could be
handled with additional code, but this is a start.
Add explicit errors for absolute paths and links found in the middle of
a path (directories). Other cases like '..' or '.' will result with the
file not being found as when those path components are explicitly
provided.
Add a helper to decompress a null-terminated link name which is shared
with cramfs_list_inode.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Using a variably-sized type is incorrect here since we're reading a
fixed file format. Fixes cramfs on 64-bit platforms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
As with most other commands, this needs to factor in the sysmem offset
in the sandbox or it will try to dereference the simulated physical
address directly.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Enable this command so we can get an approximate performance measurement.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present on a cold reboot we must reset the CPU to get it to full speed.
With 64-bit U-Boot this happens in SPL. At present we print the banner
before doing this, the end result being that we print the banner twice.
Print the banner a little later (after the CPU is ready) to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The Intel CPU name can have leading spaces. Remove them since they are not
useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A size_t variable can never be negative.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Chen-Yu Tsai
Mylène Josserand
Tom Rini
Simon Glass
xypron.glpk@gmx.de
Masahiro Yamada
Tyler Hall
Jelle van der Waa