Update the ci_udc driver to support bulk transfer
and also added capability of having multiple dtds
if requested data is more than 16K.
These changes are tested for both the DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
There's no need to store an array of QTD pointers in the controller.
Since the calculation is so simple, just have ci_get_qtd() perform it
at run-time, rather than pre-calculating everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
handle_setup() currently assumes that the response to a Setup transaction
will be an OUT transaction, and any subsequent packet (if any) will be an
IN transaction. This appears to be valid in many cases; both USB
enumeration and Mass Storage work OK with this restriction. However, DFU
uses ep0 to transfer data in both directions. This renders the assumption
invalid; when sending data from device to host, the Data Stage is an IN
transaction, and the Status Stage is an OUT transaction. Enhance
handle_setup() to deduce the correct direction for the USB transactions
based on Setup transaction data.
ep0's request object only needs to be automatically re-queued when the
Data Stage completes, in order to implement the Status Stage. Once the
Status Stage transaction is complete, there is no need to re-queue the
USB request, so don't do that.
Don't sent USB request completion callbacks for Status Stage transactions.
These were queued by ci_udc itself, and only serve to confuse the USB
function code. For example, f_dfu attempts to interpret the 0-length data
buffers for Status Stage transactions as DFU packets. These buffers
contain stale data from the previous transaction. This causes f_dfu to
complain about a sequence number mismatch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Allocate ep0's USB request object when the UDC driver is probed. This
solves a couple of issues in the current code:
a) A request object always exists for ep0. Prior to this patch, if setup
transactions arrived in an unexpected order, handle_setup() would need
to reply to a setup transaction before any ep0 usb_req was created.
This issue was introduced in commit 2813006fec "usb: ci_udc: allow
multiple buffer allocs per ep."
b) handle_ep_complete no longer /has/ to queue the ep0 request again
after every single request completion. This is currently required, since
handle_setup() assumes it can find some request object in ep0's request
queue. This patch doesn't actually stop handle_ep_complete() from always
requeueing the request, but the next patch will.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Modify ci_ep_alloc_request() to return a dynamically allocated request
object, rather than a singleton that's part of the endpoint. This
requires moving various state from the endpoint structure to the request
structure, since we need one copy per request.
The "fast bounce buffer" b_fast is removed by this change rather than
moved to the request object. Instead, we enhance the bounce buffer logic
in ci_bounce()/ci_debounce() to keep the bounce buffer around between
request submissions. This avoids the need to allocate an arbitrarily-
sized bounce buffer up-front, yet avoids incurring the allocation
overhead each time a request is submitted.
A future enhancement would be to actually submit multiple requests to HW
at once. The Linux driver shows that this is possible. That might improve
throughput (depending on the USB protocol in use), since USB could be
performing a transfer to one HW buffer in parallel with whatever SW
actions U-Boot performs on another buffer. However, I have not made this
change as part of this patch, in order to keep SW changes related to
buffer management separate from any change in the way the HW is
programmed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra's USB controller appears to be a variant of the ChipIdea
controller; perhaps derived from it, or simply a different version of
the IP core to what U-Boot supports today.
In this variant, at least the following difference are present:
- Some registers are moved about.
- Setup transaction completion is reported in a separate 'epsetupstat'
register, rather than in 'epstat' (which still exists, perhaps for
other transaction types).
- USB connection speed is reported in a separate 'hostpc1_devlc'
register, rather than 'portsc'.
- The registers used by ci_udc.c begin at offset 0x130 from the USB
register base, rather than offset 0x140. However, this is handled
by the associated EHCI controller driver, since the register address
is stored in controller.ctrl->hcor.
Introduce define CONFIG_CI_UDC_HAS_HOSTPC to indicate which variant of
the controller should be supported. The "HAS_HOSTPC" part of this name
mirrors the similar "has_hostpc" field used by the Linux EHCI controller
core to represent the presence/absence of the hostpc1_devlc register.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Move defines only needed by mv_udc.c to a file
in the same directory.
This allows usbtty to compile for mv_udc,
but it still doesn't link.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.
Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Do a coding-style cleanup of this file and throw away useless
defined values. These values were likely a result of a copy-paste
job.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Siva Durga Prasad Paladugu
Stephen Warren
Marek Vasut
Troy Kisky
Wolfgang Denk
Lucas Stach
Lei Wen