During booting, IFC is mapped to low region. After booting up, IFC is
remapped to high region for larger space. The environmental variables are
also stored at high region. In order to read the variables during booting,
a virtual mapping is required.
Cache was enabled for entire IFC space before. Actually the first two
entries are big enough (4MB) to cover the boot code and environmental
variables. Remove extra entries. Move OCRAM entry out of ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
This is required for TLB invalidation broadcasts to work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for reset_cpu() by asserting RESET_REQ_B.
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
Platform clock is half of platform PLL. There is an additional divisor
in place. Clean up code copied from powerpc.
Signed-off-by: York Sun <yorksun@freescale.com>
ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.
Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.
Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.
Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.
Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Generic Timer may contain an erroneous value. The workaround is to
read it twice until getting the same value.
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Switch to CONFIG_ARCH_INTEGRATOR defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Select integrator boards by the combination of platform select (AP/CP)
and core module select (CM720T, CM920T, ...).
This allows us to remove CONFIG_SYS_EXTRA_OPTIONS and make Kconfig
much cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
arch/arm/cpu/arm720t/start.S includes <asm/arch/hardware.h>,
but the hardware.h headers of ARM720T boards are all empty.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
For some files I neglected to add a license. Rectify this:
arch/arm/dts/exynos4210-pinctrl-uboot.dtsi
arch/arm/dts/exynos4x12-pinctrl-uboot.dtsi
arch/arm/dts/exynos5250-pinctrl-uboot.dtsi
arch/arm/dts/exynos54xx-pinctrl-uboot.dtsi
arch/arm/dts/s5pc100-pinctrl.dtsi
arch/arm/dts/s5pc110-pinctrl.dtsi
This file came from Linux and has no license information there, so add a
comment to that effect:
arch/sandbox/include/asm/bitops.h
This file also came from Linux - presumably someone from TI could add the
license:
include/dt-bindings/pinctrl/omap.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.
The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.
The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch
Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.
This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds description for NOR flash layout (firmware images)
in the README file for LS2085A platforms.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since the SoCFPGA SDRAM support is not yet applied to u-boot, we still
need to be able to compile the codebase. Introduce stub functions which
temporarily supplement the missing SDRAM setup functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Remap SDRAM to 0x0, and clear OCRAM's ECC in board_init_f().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the
SoCFPGA lowlevel_init.S file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the calls in the spl_board_init to enable SDRAM, timer, and UART.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
These functions will be needed for use by the SPL for enabling the
console and sdram initialization.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
U-Boot does not have system calls (the services it exposes to
standalone commands use a different mechanism), so the syscall handler
is dead code. It's also broken code, as it assumes it is located at
0xc00 -- while even before the patch to stop relocating exception
vectors to 0, U-Boot had the syscall at 0x900.
The critical and machine check return paths are never called -- the
regular exception return path is used instead, which works because
xSRR0/1 have already been saved and can be restored via the regular
SRR0/1 (we don't care too much in U-Boot about taking a critical/mcheck
inside another exception prolog/epilog).
Also remove a few other small unused functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Booke does not require exception vectors to be located at address zero.
U-Boot was doing so anyway, simply because that's how it had been done
on other PPC. The downside of this is that once the OS is loaded to
address zero, the exception vectors have been overwritten -- which
makes it difficult to diagnose a crash that happens after that point.
The IVOR setup and trap entry code is simplified somewhat as a result.
Also, there is no longer a need to align individual exceptions on 0x100
byte boundaries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add dummy bootz_setup implementation allowing the u-boot sandbox to
run bootz. This recognizes both ARM and x86 zImages to validate a
valid zImage was loaded.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Follow the convention of other architectures and move the platform
specific linux bootm code into sandbox/lib/bootm.c.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
York Sun
Scott Wood
pankaj chauhan
Prabhakar Kushwaha
Simon Glass
Masahiro Yamada
rev13@wp.pl
Fabio Estevam
Tim Harvey
Jörg Krause
Bhupesh Sharma
Zhao Qiang
Minghuan Lian
gaurav rana
Alison Wang
Marek Vasut
Dinh Nguyen
Shengzhou Liu
Heiko Schocher
Sjoerd Simons
Joe Hershberger