In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree. In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: Tom Rini <trini@ti.com>
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: Tom Rini <trini@ti.com>
The ELM hardware engine wihich is used for ECC error detections is not present
on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to
SoC configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
rdaddr was missing which is a common location for loading ramdisks to.
loadaddr was higher than it needs to be, so use the same value other TI
platforms use.
Signed-off-by: Tom Rini <trini@ti.com>
OMAP5 boards may have both eMMC (on MMC2) and an SD slot (on MMC1). We
Update the default bootcmd to match what happens on AM335x where we try
SD first, and then eMMC. In this case however, the hardware layout used
for powering both of these means that in the kernel eMMC shall be found
first as it is powered by a fixed regulator and SD found second as SD is
powered via the palmas which will result in deferred probing.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <trini@ti.com>
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run. If the file is not defined then warn the user that the
dtb file is not defined.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
The sys_clk on the dra evm board is 20MHZ.
Changing the configuration for the same.
And also moving V_SCLK, V_OSCK defines to
arch/clock.h for OMAP4+ boards.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The boot parameters passed from SPL to UBOOT
must be saved as a part of uboot's gd data
as early as possible, before we will inadvertently
overwrite it. So adding a arch_cpu_init for the required
Socs to save it.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
Add 'optargs' variable to be set to additional kernel arguments, similar
to omap3*/am3* usage.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Now with kernel moving to all device tree, the default
boot command is changed to pass the device tree blob.
Also, adding the findfdt command to get the dt-blob
based on the board.
Thanks to Tom Rini <trini@ti.com> for suggesting this.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
For production systems it is better to use script images since
they are protected by checksums and carry valuable information
like name and timestamp. Also, you can't validate the content
passed to env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP5evm/uevm boards are used primarily for development,
we allow U-Boot to load env var from a text file in case that an
boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Inspired by commit: d70f54808d
(omap4: allow the use of a plain text env file instead boot scripts)
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Sricharan R <r.sricharan@ti.com>
While booting with dt blob, if fdt_high is not set to
0xffffffff, the dt blob gets relocated to a high ram address,
which the kernel is not able to use without HIGHMEM.
So set it to 0xffffffff to avoid the issue.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Adding the build support for dra7xx_evm.
Reusing omap5_evm.h config by moving it to omap5_common.h
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
With v3.9 and later of the Linux Kernel defaulting to multi-platform
images with omap2plus_defconfig, uImage isn't builtable anymore by
default. Add CONFIG_CMD_BOOTZ so that we can still boot something the
kernel spits out.
Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Fix usage of 'mmc rescan' by many configs. Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device. 'mmc rescan' itself does not take any arguments.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
Only omap4/5 currently have a meaningful set of display text and overo
had been adding a function to display nothing. Change how this works to
be opt-in and only turned on for omap4/5 now.
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.
IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Make the lowlevel_init function that these platforms have which just
sets up the stack and calls a C function available to all armv7
platforms. As part of this we change some of the macros that are used
to be more clear. Previously (except for am335x evm) we had been
setting CONFIG_SYS_INIT_SP_ADDR to a series of new defines that are
equivalent to simply referencing NON_SECURE_SRAM_END. On am335x evm we
should have been doing this initially and do now.
Cc: Sricharan R <r.sricharan@ti.com>
Tested-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Currently on OMAP4/5 platforms, many kernel drivers are dependent
upon the bootloaders for mux, dpll and clock configurations.
This should not be the case and bootloaders should set only the
minimum required for the uboot functionality and kernel boot.
Note that this is going to break the kernel drivers. But this
is the only way to get things fixed in the kernel.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Change the CONFIG_SYS_TEXT_BASE and the addresses of SDRAM
buffers used by SPL(heap and BSS) keeping in mind the
following requirements:
1. Make sure that SPL's heap and BSS doesn't come in the way
of Linux kernel, which is typically loaded at 0x80008000. This
will be important when SPL directly loads kernel.
2. Align the CONFIG_SYS_TEXT_BASE between TI internal
U-Boot and mainline U-Boot. This avoids a lot of confusion
and allows for the inter-operability of x-loader, SPL,
internal U-Boot, mainline U-Boot etc. The internal U-Boot's
address can not be changed to that of mainline U-Boot
as internal U-Boot doesn't have relocation and 0x80100000
used by mainline U-Boot will clash with kernel
3. Assume only a minimum amount of memory that may be available
on any practical OMAP4/5 board in future too. We are assuming
a minimum of 128 MB of memory
Signed-off-by: Aneesh V <aneesh@ti.com>
This patch adds the build support for the
omap5_evm board.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
FAT library now uses malloc() and free(). But SPL doesn't
have heap until now. Setup a heap in SDRAM to fix this issue.
However this increases SPL footprint beyond the available SRAM
budget. So, compile out some fancy features in the SDARM init
bring back footprint under control
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
All ddr configurations(geometry/timings) are done automatically
by detecting the device connected at run time. Though this
is a useful feature, making this as a default setting increases
the code size by about 2K bytes. This is quite big, especially
in the case of SPL which runs from a smaller SRAM. So do not
use this feature as the default setting, instead use the
precalculated tables.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Lokesh Vutla
Tom Rini
Enric Balletbò i Serra
Wolfgang Denk
Dan Murphy
Balaji T K
Sricharan R
Nishanth Menon
Andrew Bradford
Rob Herring
Marek Vasut
Thomas Weber
Aneesh V