mars and riot boards use UART2 as console, so CONFIG_CONSOLE_DEV should point
to 'ttymxc1' instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
Commit e9fd66defd (ARM: mx6: define CONFIG_ARM_ERRATA_742230) enables
errata 742230 for imx6, because it helps remove one reboot issue.
However, this errata does not really apply on imx6, because Cortex-A9
on imx6 is r2p10 while the errata only applies to revisions r1p0..r2p2.
At a later time, commit f71cbfe3ca (ARM: Add workaround for Cortex-A9
errata 794072) adds support of errata 794072, which applies to all
Cortex-A9 revisions. As the workaround for both errata are exactly
same, it makes a lot more sense to select 794072 instead of 742230 for
imx6. Since we already enable 794072 for imx6, it's time to drop
errata 742230 to avoid confusion.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Switch to an SPL image. The SPL for Ventana does the following:
- setup i2c and read the factory programmed EEPROM to obtain DRAM config
and model for board-specific calibration data
- configure DRAM per CPU/size/layout/devices/calibration
- load u-boot.img from NAND and jump to it
This allows for a single SPL+u-boot.img to replace the previous multiple boa
configurations.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a common header which can hopefully be shared amon imx6 SPL users
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for booting from an MMC card.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i)
processors. Enable for the Cubietruck.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move addresses for kernel, ramdisk and fdt blob to own variables. Add dtb
blob loading to all existing boot scripts, dtb filenames were taken from
vanilla kernel. Introduce new boot script bootcmd_legacy, which only loads
a kernel and a ramdisk. Make this the default boot script. This should also
restore the behaviour of the original bootloader.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>
cm-t54 Eth MAC address is stored in onboard EEPROM.
Add EEPROM support and setup stored Eth MAC address.
If EEPROM does not contain a valid MAC, then generate it from the
processor ID code (reference code is taken from OMAP5 uEvm board file).
Modify Device Tree blob MAC address field with retrieved data.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Tested-by: Samuel Egli <samuel.egli@siemens.com>
This adds the Gumstix DuoVero machine [1]. This is a OMAP4430-based
computer-on-module (COM aka SOM) that can be mounted on various
expansion boards with different peripherals.
[1] https://store.gumstix.com/index.php/category/43/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Rename gpmc_enable_gpmc_cs_config to gpmc_enable_gpmc_net_config]
Signed-off-by: Tom Rini <trini@ti.com>
Clean-up the board configuration file for the Gumstix Overo board by
including common omap3 definitions from ti_omap3_common.h as suggested
here [1].
[1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/185960
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Conflicts:
include/configs/omap3_overo.h
Update the board configuration for Gumstix Overo. In particular,
add support for zImage and DTB files on boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Overo. Since some gpio inputs are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
The linux kernel is at nand0,3 using the current layout, but is best
accessed through the partition label "linux". Since CONFIG_CMD_MTDPARTS is
defined the CONFIG_JFFS2 settings are unreferenced; use "setenv partition
rootfs" to set the default mtd partition for jffs2.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
Linux kernel at version 3.5 is about 3.5 MiB; test kernels for 3.10 exceed 4
MiB. Prepare for future upgrades by increasing the NAND partition now.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
The NAND linux partition format default was changed from jffs2 to ubi in
254973e6df but the corresponding commands were
not enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
Adapted from d70f5480 described below.
commit d70f54808d
Author: Javier Martinez Canillas <javier@dowhile0.org>
Date: Mon Jan 7 03:51:20 2013 +0000
omap4: allow the use of a plain text env file instead boot scripts
For production systems it is better to use script images since
they are protected by checksums and carry valuable information like
name and timestamp. Also, you can't validate the content passed to
env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP4 supported boards (Panda and TI SDP4430) are used
primarily for development, this patch allows U-Boot to load env var
from a text file in case that an boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
User's confirmation is asked in different commands. This commit adds a
function for such confirmation.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Since B&R boards uses only MMC-Controller #1, it only
wastes time if we initialize #0 first to see that there is nothing.
Cc: <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Added support to load partial bitstreams.
The partial bitstreams can be loaded using the below commands
Commands:
fpga loadp <dev> <addr> <size>
fpga loadbp <dev> <addr> <size>
The full bit streams can be loaded using the
old commands(fpga load and fpga loadb).
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fabio Estevam
Shawn Guo
Marek Vasut
Tim Harvey
Ian Campbell
Rob Herring
Michael Walle
Dmitry Lifshitz
Heiko Schocher
Ash Charles
Peter A. Bigot
Stephen Warren
Pierre Aubert
Andrew Gabbasov
Hannes Petermaier
Nobuhiro Iwamatsu
Siva Durga Prasad Paladugu
Michal Simek