This symbol is not used anywhere, so remove it. For spear600, remove
it from the board file, since the symbol is not defined for spear600
either.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Booting SPEAr600 eval board doesn't work with current mainline U-Boot. With
this patch the low-vector bit is left to '0'. Resulting in the common
relocation of the vectors to 0 (SDRAM) to work correctly.
Tested on the SPEAr600 EVB.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
We are going to switch over to Kbuild in upcoming commits.
Each makefile must have non-empty obj- or obj-y
to generate built-in.o on Kbuild.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds support for the X600 SPEAr600 based board. Its also
the first SPEAr600 board that uses the newly introduced SPEAr600
SPL support. Xloader is not necessary any more. By using the new
"u-boot.spr" make target, one image will generated containing both,
U-Boot SPL (with mkimage header as needed by the SPEAr BootROM, and
the main U-Boot with mkimage header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Enable data cache with 1:1 mapping of DDR to enable fast file
transfer over tty which was doing lot of copy.
This feature is enabled only for flashing operation i.e. when
CONFIG_SPEAR_USBTTY is enabled.
This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation
boards.
Following figures show an estimate on the performance improvements. The
test setup was a Linux host (not Windows) and involved measurement of
only binary transfer time, through kermit. The flash erase and flash
copy time would be unaffected by these patches.
Another thing is this that the timings remained more or less same across
ARM9 and Cortex based devices, hence reporting only one of the cases.
Before Enhancements
===================
$ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m41.228s
user 0m0.002s
sys 0m0.064s
After Enhancements
==================
$ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img
Downloading file: 100.00% completed(2014080/2014080 bytes)
real 0m5.441s
user 0m0.001s
sys 0m0.001s
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
flash reading is required earlier than flash_init is called since the env_init
is called before flash_init. This makes the smi_init necessary before env_init
being called.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds options for all the below mentioned configurations and
subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h,
spear6xx_evb.h etc to depict evaluation board configuration.
SPEAr3xx and SPEAr6xx boards can be compiled in following configurations
1. Environment placed in NAND
2. Console on usb device
3. Console on usb device with environment placed in NAND
4. SPEAr310 and SPEAr320 support environment variables in parallel
NOR flash.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
ethaddr can be optionally read from i2c memory. So, chip_config command supports
reading/writing hw mac id into i2c memory. Placing this code within
CONFIG_CMD_NET as this would only be needed when network interface is configured
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
While the u-boot code is running from the flash, it is essential that no access
is made to the bss segment. This is due to the fact that .rel.dyn and .bss areas
overlap and former contains information used in relocation. In SPEAr, this was
not taken into consideration. As a result, while the relocation wasn't complete,
dram_init populated an uninitialized global variable resulting in corruption of
.rel.dyn area, which resulted in u-boot crash.
This commit fixes this problem by removing code that accesses bss segment
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Supporting new machine ids for SoCs spear310 and spear320
include/asm-arm/mach-types.h has to be updated before applying
this patch for build to work
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
SPEAr320 SoC support contains basic spear320 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 and SPEAr320 SoCs contain an EMI controller to interface
Paraller NOR flashes. This patch adds the support for this IP
The standard CFI driver is used to interface with NOR flashes
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
This patch adds the support to read and write mac id from i2c
memory.
For reading:
if (env contains ethaddr)
pick env ethaddr
else
pick ethaddr from i2c memory
For writing:
chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
in i2c memory
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr320 SoC support contains basic spear320 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 and SPEAr320 SoCs contain an EMI controller to interface
Paraller NOR flashes. This patch adds the support for this IP
The standard CFI driver is used to interface with NOR flashes
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
This patch adds the support to read and write mac id from i2c
memory.
For reading:
if (env contains ethaddr)
pick env ethaddr
else
pick ethaddr from i2c memory
For writing:
chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
in i2c memory
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>