/* * Copyright 2015 Timesys Corporation * Copyright 2015 General Electric Company * Copyright 2012 Freescale Semiconductor, Inc. * * SPDX-License-Identifier: GPL-2.0+ */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "../common/ge_common.h" #include "../common/vpd_reader.h" #include "../../../drivers/net/e1000.h" DECLARE_GLOBAL_DATA_PTR; #ifndef CONFIG_SYS_I2C_EEPROM_ADDR # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #endif #ifndef CONFIG_SYS_I2C_EEPROM_BUS #define CONFIG_SYS_I2C_EEPROM_BUS 4 #endif #define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_HYS) #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) #define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ PAD_CTL_ODE | PAD_CTL_SRE_FAST) #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL) int dram_init(void) { gd->ram_size = imx_ddr_size(); return 0; } static iomux_v3_cfg_t const uart3_pads[] = { MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; static iomux_v3_cfg_t const uart4_pads[] = { MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; static iomux_v3_cfg_t const enet_pads[] = { MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), /* AR8033 PHY Reset */ MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), }; static void setup_iomux_enet(void) { imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); /* Reset AR8033 PHY */ gpio_direction_output(IMX_GPIO_NR(1, 28), 0); mdelay(10); gpio_set_value(IMX_GPIO_NR(1, 28), 1); mdelay(1); } static iomux_v3_cfg_t const usdhc2_pads[] = { MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), }; static iomux_v3_cfg_t const usdhc3_pads[] = { MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; static iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), }; static iomux_v3_cfg_t const ecspi1_pads[] = { MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), }; static struct i2c_pads_info i2c_pad_info1 = { .scl = { .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD, .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD, .gp = IMX_GPIO_NR(5, 27) }, .sda = { .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD, .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD, .gp = IMX_GPIO_NR(5, 26) } }; static struct i2c_pads_info i2c_pad_info2 = { .scl = { .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD, .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD, .gp = IMX_GPIO_NR(4, 12) }, .sda = { .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD, .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD, .gp = IMX_GPIO_NR(4, 13) } }; static struct i2c_pads_info i2c_pad_info3 = { .scl = { .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD, .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD, .gp = IMX_GPIO_NR(1, 3) }, .sda = { .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD, .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD, .gp = IMX_GPIO_NR(1, 6) } }; #ifdef CONFIG_MXC_SPI int board_spi_cs_gpio(unsigned bus, unsigned cs) { return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1; } static void setup_spi(void) { imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); } #endif static iomux_v3_cfg_t const pcie_pads[] = { MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), }; static void setup_pcie(void) { imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); } static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads)); imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); } #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg usdhc_cfg[3] = { {USDHC2_BASE_ADDR}, {USDHC3_BASE_ADDR}, {USDHC4_BASE_ADDR}, }; #define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) #define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11) int board_mmc_getcd(struct mmc *mmc) { struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; int ret = 0; switch (cfg->esdhc_base) { case USDHC2_BASE_ADDR: ret = !gpio_get_value(USDHC2_CD_GPIO); break; case USDHC3_BASE_ADDR: ret = 1; /* eMMC is always present */ break; case USDHC4_BASE_ADDR: ret = !gpio_get_value(USDHC4_CD_GPIO); break; } return ret; } int board_mmc_init(bd_t *bis) { int ret; int i; for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { switch (i) { case 0: imx_iomux_v3_setup_multiple_pads( usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); gpio_direction_input(USDHC2_CD_GPIO); usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); break; case 1: imx_iomux_v3_setup_multiple_pads( usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); break; case 2: imx_iomux_v3_setup_multiple_pads( usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); gpio_direction_input(USDHC4_CD_GPIO); usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); break; default: printf("Warning: you configured more USDHC controllers\n" "(%d) then supported by the board (%d)\n", i + 1, CONFIG_SYS_FSL_USDHC_NUM); return -EINVAL; } ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); if (ret) return ret; } return 0; } #endif static int mx6_rgmii_rework(struct phy_device *phydev) { /* Configure AR8033 to ouput a 125MHz clk from CLK_25M */ /* set device address 0x7 */ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); /* offset 0x8016: CLK_25M Clock Select */ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); /* enable register write, no post increment, address 0x7 */ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); /* set to 125 MHz from local PLL source */ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18); /* rgmii tx clock delay enable */ /* set debug port address: SerDes Test and System Mode Control */ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); /* enable rgmii tx clock delay */ /* set the reserved bits to avoid board specific voltage peak issue*/ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47); return 0; } int board_phy_config(struct phy_device *phydev) { mx6_rgmii_rework(phydev); if (phydev->drv->config) phydev->drv->config(phydev); return 0; } #if defined(CONFIG_VIDEO_IPUV3) static iomux_v3_cfg_t const backlight_pads[] = { /* Power for LVDS Display */ MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), #define LVDS_POWER_GP IMX_GPIO_NR(3, 22) /* Backlight enable for LVDS display */ MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), #define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0) /* backlight PWM brightness control */ MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), }; static void do_enable_hdmi(struct display_info_t const *dev) { imx_enable_hdmi_phy(); } int board_cfb_skip(void) { gpio_direction_output(LVDS_POWER_GP, 1); return 0; } static int detect_baseboard(struct display_info_t const *dev) { if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) || IS_ENABLED(CONFIG_TARGET_GE_B650V3)) return 1; return 0; } struct display_info_t const displays[] = {{ .bus = -1, .addr = -1, .pixfmt = IPU_PIX_FMT_RGB24, .detect = detect_baseboard, .enable = NULL, .mode = { .name = "G121X1-L03", .refresh = 60, .xres = 1024, .yres = 768, .pixclock = 15385, .left_margin = 20, .right_margin = 300, .upper_margin = 30, .lower_margin = 8, .hsync_len = 1, .vsync_len = 1, .sync = FB_SYNC_EXT, .vmode = FB_VMODE_NONINTERLACED } }, { .bus = -1, .addr = 3, .pixfmt = IPU_PIX_FMT_RGB24, .detect = detect_hdmi, .enable = do_enable_hdmi, .mode = { .name = "HDMI", .refresh = 60, .xres = 1024, .yres = 768, .pixclock = 15385, .left_margin = 220, .right_margin = 40, .upper_margin = 21, .lower_margin = 7, .hsync_len = 60, .vsync_len = 10, .sync = FB_SYNC_EXT, .vmode = FB_VMODE_NONINTERLACED } } }; size_t display_count = ARRAY_SIZE(displays); static void enable_videopll(void) { struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; s32 timeout = 100000; setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); /* set video pll to 910MHz (24MHz * (37+11/12)) * video pll post div to 910/4 = 227.5MHz */ clrsetbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_DIV_SELECT | BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT, BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) | BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0)); writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num); writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom); clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN); while (timeout--) if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK) break; if (timeout < 0) printf("Warning: video pll lock timeout!\n"); clrsetbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_BYPASS, BM_ANADIG_PLL_VIDEO_ENABLE); } static void setup_display_b850v3(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; enable_videopll(); /* IPU1 D0 clock is 227.5 / 3.5 = 65MHz */ clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); imx_setup_hdmi(); /* Set LDB_DI0 as clock source for IPU_DI0 */ clrsetbits_le32(&mxc_ccm->chsccdr, MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, (CHSCCDR_CLK_SEL_LDB_DI0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); /* Turn on IPU LDB DI0 clocks */ setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); enable_ipu_clock(); writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | IOMUXC_GPR2_SPLIT_MODE_EN_MASK | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0, &iomux->gpr[2]); clrbits_le32(&iomux->gpr[3], IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | IOMUXC_GPR3_HDMI_MUX_CTL_MASK); } static void setup_display_bx50v3(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; /* When a reset/reboot is performed the display power needs to be turned * off for atleast 500ms. The boot time is ~300ms, we need to wait for * an additional 200ms here. Unfortunately we use external PMIC for * doing the reset, so can not differentiate between POR vs soft reset */ mdelay(200); /* IPU1 DI0 clock is 480/7 = 68.5 MHz */ setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); /* Set LDB_DI0 as clock source for IPU_DI0 */ clrsetbits_le32(&mxc_ccm->chsccdr, MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, (CHSCCDR_CLK_SEL_LDB_DI0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); /* Turn on IPU LDB DI0 clocks */ setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); enable_ipu_clock(); writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0, &iomux->gpr[2]); clrsetbits_le32(&iomux->gpr[3], IOMUXC_GPR3_LVDS0_MUX_CTL_MASK, (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)); /* backlights off until needed */ imx_iomux_v3_setup_multiple_pads(backlight_pads, ARRAY_SIZE(backlight_pads)); gpio_direction_input(LVDS_POWER_GP); gpio_direction_input(LVDS_BACKLIGHT_GP); } #endif /* CONFIG_VIDEO_IPUV3 */ /* * Do not overwrite the console * Use always serial for U-Boot console */ int overwrite_console(void) { return 1; } #define VPD_TYPE_INVALID 0x00 #define VPD_BLOCK_NETWORK 0x20 #define VPD_BLOCK_HWID 0x44 #define VPD_PRODUCT_B850 1 #define VPD_PRODUCT_B650 2 #define VPD_PRODUCT_B450 3 #define VPD_HAS_MAC1 0x1 #define VPD_HAS_MAC2 0x2 #define VPD_MAC_ADDRESS_LENGTH 6 struct vpd_cache { u8 product_id; u8 has; unsigned char mac1[VPD_MAC_ADDRESS_LENGTH]; unsigned char mac2[VPD_MAC_ADDRESS_LENGTH]; }; /* * Extracts MAC and product information from the VPD. */ static int vpd_callback(void *userdata, u8 id, u8 version, u8 type, size_t size, u8 const *data) { struct vpd_cache *vpd = (struct vpd_cache *)userdata; if (id == VPD_BLOCK_HWID && version == 1 && type != VPD_TYPE_INVALID && size >= 1) { vpd->product_id = data[0]; } else if (id == VPD_BLOCK_NETWORK && version == 1 && type != VPD_TYPE_INVALID) { if (size >= 6) { vpd->has |= VPD_HAS_MAC1; memcpy(vpd->mac1, data, VPD_MAC_ADDRESS_LENGTH); } if (size >= 12) { vpd->has |= VPD_HAS_MAC2; memcpy(vpd->mac2, data + 6, VPD_MAC_ADDRESS_LENGTH); } } return 0; } static void process_vpd(struct vpd_cache *vpd) { int fec_index = -1; int i210_index = -1; switch (vpd->product_id) { case VPD_PRODUCT_B450: env_set("confidx", "1"); break; case VPD_PRODUCT_B650: env_set("confidx", "2"); break; case VPD_PRODUCT_B850: env_set("confidx", "3"); break; } switch (vpd->product_id) { case VPD_PRODUCT_B450: /* fall thru */ case VPD_PRODUCT_B650: i210_index = 0; fec_index = 1; break; case VPD_PRODUCT_B850: i210_index = 1; fec_index = 2; break; } if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1)) eth_env_set_enetaddr_by_index("eth", fec_index, vpd->mac1); if (i210_index >= 0 && (vpd->has & VPD_HAS_MAC2)) eth_env_set_enetaddr_by_index("eth", i210_index, vpd->mac2); } static int read_vpd(uint eeprom_bus) { struct vpd_cache vpd; int res; int size = 1024; uint8_t *data; unsigned int current_i2c_bus = i2c_get_bus_num(); res = i2c_set_bus_num(eeprom_bus); if (res < 0) return res; data = (uint8_t *)malloc(size); if (!data) return -ENOMEM; res = i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, data, size); if (res == 0) { memset(&vpd, 0, sizeof(vpd)); vpd_reader(size, data, &vpd, vpd_callback); process_vpd(&vpd); } free(data); i2c_set_bus_num(current_i2c_bus); return res; } int board_eth_init(bd_t *bis) { setup_iomux_enet(); setup_pcie(); e1000_initialize(bis); return cpu_eth_init(bis); } static iomux_v3_cfg_t const misc_pads[] = { MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL), MX6_PAD_GPIO_9__WDOG1_B | MUX_PAD_CTRL(NC_PAD_CTRL), }; #define SUS_S3_OUT IMX_GPIO_NR(4, 11) #define WIFI_EN IMX_GPIO_NR(6, 14) int board_early_init_f(void) { imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads)); setup_iomux_uart(); #if defined(CONFIG_VIDEO_IPUV3) if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) /* Set LDB clock to Video PLL */ select_ldb_di_clock_source(MXC_PLL5_CLK); else /* Set LDB clock to USB PLL */ select_ldb_di_clock_source(MXC_PLL3_SW_CLK); #endif return 0; } int board_init(void) { gpio_direction_output(SUS_S3_OUT, 1); gpio_direction_output(WIFI_EN, 1); #if defined(CONFIG_VIDEO_IPUV3) if (IS_ENABLED(CONFIG_TARGET_GE_B850V3)) setup_display_b850v3(); else setup_display_bx50v3(); #endif /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; #ifdef CONFIG_MXC_SPI setup_spi(); #endif setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); return 0; } #ifdef CONFIG_CMD_BMODE static const struct boot_mode board_boot_modes[] = { /* 4 bit bus width */ {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, {NULL, 0}, }; #endif void pmic_init(void) { #define I2C_PMIC 0x2 #define DA9063_I2C_ADDR 0x58 #define DA9063_REG_BCORE2_CFG 0x9D #define DA9063_REG_BCORE1_CFG 0x9E #define DA9063_REG_BPRO_CFG 0x9F #define DA9063_REG_BIO_CFG 0xA0 #define DA9063_REG_BMEM_CFG 0xA1 #define DA9063_REG_BPERI_CFG 0xA2 #define DA9063_BUCK_MODE_MASK 0xC0 #define DA9063_BUCK_MODE_MANUAL 0x00 #define DA9063_BUCK_MODE_SLEEP 0x40 #define DA9063_BUCK_MODE_SYNC 0x80 #define DA9063_BUCK_MODE_AUTO 0xC0 uchar val; i2c_set_bus_num(I2C_PMIC); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE2_CFG, 1, &val, 1); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BCORE1_CFG, 1, &val, 1); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPRO_CFG, 1, &val, 1); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BIO_CFG, 1, &val, 1); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BMEM_CFG, 1, &val, 1); i2c_read(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1); val &= ~DA9063_BUCK_MODE_MASK; val |= DA9063_BUCK_MODE_SYNC; i2c_write(DA9063_I2C_ADDR, DA9063_REG_BPERI_CFG, 1, &val, 1); } int board_late_init(void) { read_vpd(CONFIG_SYS_I2C_EEPROM_BUS); #ifdef CONFIG_CMD_BMODE add_board_boot_modes(board_boot_modes); #endif /* board specific pmic init */ pmic_init(); check_time(); return 0; } /* * Removes the 'eth[0-9]*addr' environment variable with the given index * * @param index [in] the index of the eth_device whose variable is to be removed */ static void remove_ethaddr_env_var(int index) { char env_var_name[9]; sprintf(env_var_name, index == 0 ? "ethaddr" : "eth%daddr", index); env_set(env_var_name, NULL); } int last_stage_init(void) { int i; /* * Remove first three ethaddr which may have been created by * function process_vpd(). */ for (i = 0; i < 3; ++i) remove_ethaddr_env_var(i); return 0; } int checkboard(void) { printf("BOARD: %s\n", CONFIG_BOARD_NAME); return 0; } static int do_backlight_enable(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { #ifdef CONFIG_VIDEO_IPUV3 /* We need at least 200ms between power on and backlight on * as per specifications from CHI MEI */ mdelay(250); /* enable backlight PWM 1 */ pwm_init(0, 0, 0); /* duty cycle 5000000ns, period: 5000000ns */ pwm_config(0, 5000000, 5000000); /* Backlight Power */ gpio_direction_output(LVDS_BACKLIGHT_GP, 1); pwm_enable(0); #endif return 0; } U_BOOT_CMD( bx50_backlight_enable, 1, 1, do_backlight_enable, "enable Bx50 backlight", "" );