upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/freescale/p1022ds/ddr.c

106 lines
2.7 KiB

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2010 Freescale Semiconductor, Inc.
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
* Timur Tabi <timur@freescale.com>
*/
#include <common.h>
#include <fsl_ddr_sdram.h>
#include <fsl_ddr_dimm_params.h>
struct board_specific_parameters {
u32 n_ranks;
u32 datarate_mhz_high;
u32 clk_adjust; /* Range: 0-8 */
u32 cpo; /* Range: 2-31 */
u32 write_data_delay; /* Range: 0-6 */
u32 force_2t;
};
/*
* This table contains all valid speeds we want to override with board
* specific parameters. datarate_mhz_high values need to be in ascending order
* for each n_ranks group.
*/
static const struct board_specific_parameters dimm0[] = {
/*
* memory controller 0
* num| hi| clk| cpo|wrdata|2T
* ranks| mhz|adjst| | delay|
*/
{1, 549, 5, 31, 3, 0},
{1, 850, 5, 31, 5, 0},
{2, 549, 5, 31, 3, 0},
{2, 850, 5, 31, 5, 0},
{}
};
void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
unsigned int ctrl_num)
{
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
unsigned long ddr_freq;
unsigned int i;
if (ctrl_num) {
printf("Wrong parameter for controller number %d", ctrl_num);
return;
}
if (!pdimm->n_ranks)
return;
/* set odt_rd_cfg and odt_wr_cfg. */
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
popts->cs_local_opts[i].odt_rd_cfg = 0;
popts->cs_local_opts[i].odt_wr_cfg = 1;
}
pbsp = dimm0;
/*
* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
while (pbsp->datarate_mhz_high) {
if (pbsp->n_ranks == pdimm->n_ranks) {
if (ddr_freq <= pbsp->datarate_mhz_high) {
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay =
pbsp->write_data_delay;
popts->twot_en = pbsp->force_2t;
goto found;
}
pbsp_highest = pbsp;
}
pbsp++;
}
if (pbsp_highest) {
printf("Error: board specific timing not found "
"for data rate %lu MT/s!\n"
"Trying to use the highest speed (%u) parameters\n",
ddr_freq, pbsp_highest->datarate_mhz_high);
popts->clk_adjust = pbsp->clk_adjust;
popts->cpo_override = pbsp->cpo;
popts->write_data_delay = pbsp->write_data_delay;
popts->twot_en = pbsp->force_2t;
} else {
panic("DIMM is not supported by this board");
}
found:
popts->half_strength_driver_enable = 1;
/* Per AN4039, enable ZQ calibration. */
popts->zq_en = 1;
/*
* For wake-up on ARP, we need auto self refresh enabled
*/
popts->auto_self_refresh_en = 1;
popts->sr_it = 0xb;
}