upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/st/stv0991/stv0991.c

115 lines
2.1 KiB

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2014, STMicroelectronics - All Rights Reserved
* Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics.
*/
#include <common.h>
#include <dm.h>
#include <miiphy.h>
#include <asm/arch/stv0991_periph.h>
#include <asm/arch/stv0991_defs.h>
#include <asm/arch/hardware.h>
#include <asm/arch/gpio.h>
#include <netdev.h>
#include <asm/io.h>
#include <dm/platform_data/serial_pl01x.h>
DECLARE_GLOBAL_DATA_PTR;
struct gpio_regs *const gpioa_regs =
(struct gpio_regs *) GPIOA_BASE_ADDR;
#ifndef CONFIG_OF_CONTROL
static const struct pl01x_serial_platdata serial_platdata = {
.base = 0x80406000,
.type = TYPE_PL011,
.clock = 2700 * 1000,
};
U_BOOT_DEVICE(stv09911_serials) = {
.name = "serial_pl01x",
.platdata = &serial_platdata,
};
#endif
#ifdef CONFIG_SHOW_BOOT_PROGRESS
void show_boot_progress(int progress)
{
printf("%i\n", progress);
}
#endif
void enable_eth_phy(void)
{
/* Set GPIOA_06 pad HIGH (Appli board)*/
writel(readl(&gpioa_regs->dir) | 0x40, &gpioa_regs->dir);
writel(readl(&gpioa_regs->data) | 0x40, &gpioa_regs->data);
}
int board_eth_enable(void)
{
stv0991_pinmux_config(ETH_GPIOB_10_31_C_0_4);
clock_setup(ETH_CLOCK_CFG);
enable_eth_phy();
return 0;
}
int board_qspi_enable(void)
{
stv0991_pinmux_config(QSPI_CS_CLK_PAD);
clock_setup(QSPI_CLOCK_CFG);
return 0;
}
/*
* Miscellaneous platform dependent initialisations
*/
int board_init(void)
{
board_eth_enable();
board_qspi_enable();
return 0;
}
int board_uart_init(void)
{
stv0991_pinmux_config(UART_GPIOC_30_31);
clock_setup(UART_CLOCK_CFG);
return 0;
}
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
board_uart_init();
return 0;
}
#endif
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_1_SIZE;
return 0;
}
int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
return 0;
}
#ifdef CONFIG_CMD_NET
int board_eth_init(bd_t *bis)
{
int ret = 0;
#if defined(CONFIG_ETH_DESIGNWARE)
u32 interface = PHY_INTERFACE_MODE_MII;
if (designware_initialize(GMAC_BASE_ADDR, interface) >= 0)
ret++;
#endif
return ret;
}
#endif