upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/DU440.h

432 lines
15 KiB

/*
* (C) Copyright 2008
* Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
*
* based on the Sequoia board configuration by
* Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
**********************************************************************
* DU440.h - configuration for esd's DU440 board (Power PC440EPx)
**********************************************************************
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_DU440 1 /* Board is esd DU440 */
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND0_ADDR 0xd0000000 /* NAND Flash */
#define CONFIG_SYS_NAND1_ADDR 0xd0100000 /* NAND Flash */
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
#define CONFIG_SYS_PCI_IOBASE 0xe8000000
#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
/*
* Initial RAM & stack pointer
*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
#define CONFIG_SYS_INIT_RAM_OCM 1 /* OCM as init ram */
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
#define CONFIG_BAUDRATE 115200
#define CONFIG_SERIAL_MULTI 1
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*
* Video Port
*/
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SMI_LYNXEM
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_ISA_IO CONFIG_SYS_PCI_IOBASE
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
/*
* FLASH related
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_OFFSET 0 /* environment starts at */
/* the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
#endif
/*
* DDR SDRAM
*/
#define CONFIG_SYS_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
/* 440EPx errata CHIP 11 */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define CONFIG_DDR_ECC /* Use ECC when available */
#define SPD_EEPROM_ADDRESS {0x50}
#define CONFIG_PROG_SDRAM_TLB
/*
* I2C
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_SYS_SPD_BUS_NUM 0
#define IIC1_MCP3021_ADDR 0x4d
#define IIC1_USB2507_ADDR 0x2c
#ifdef CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
#endif
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
/*
* standard dtt sensor configuration - bottom bit will determine local or
* remote sensor of the TMP401
*/
#define CONFIG_DTT_SENSORS { 0, 1 }
/*
* The PMC440 uses a TI TMP401 temperature sensor. This part
* is basically compatible to the ADM1021 that is supported
* by U-Boot.
*
* - i2c addr 0x4c
* - conversion rate 0x02 = 0.25 conversions/second
* - ALERT ouput disabled
* - local temp sensor enabled, min set to 0 deg, max set to 70 deg
* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
*/
#define CONFIG_DTT_ADM1021
#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
/*
* RTC stuff
*/
#define CONFIG_RTC_DS1338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"ethrotate=no\0" \
"hostname=du440\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_self=run ramargs addip addtty optargs;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \
"bootm\0" \
"rootpath=/tftpboot/du440/target_root_du440\0" \
"img=/tftpboot/du440/uImage\0" \
"kernel_addr=FFC00000\0" \
"ramdisk_addr=FFE00000\0" \
"initrd_high=30000000\0" \
"load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \
"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
"cp.b 100000 FFFA0000 60000\0" \
""
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#ifndef __ASSEMBLY__
int du440_phy_addr(int devnum);
#endif
#define CONFIG_PPC4xx_EMAC
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#undef CONFIG_PHY_GIGE /* no GbE detection */
#define CONFIG_HAS_ETH0
#define CONFIG_SYS_RX_ETH_BUFFER 128
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR du440_phy_addr(1)
/*
* USB
*/
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "du440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_BMP
#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SOURCE
#define CONFIG_CMD_USB
#define CONFIG_SUPPORT_VFAT
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CONFIG_AUTOBOOT_KEYED 1
#define CONFIG_AUTOBOOT_PROMPT \
"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "d"
#define CONFIG_AUTOBOOT_STOP_STR " "
/*
* PCI stuff
*/
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* External Bus Controller (EBC) Setup
*/
#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CPLD_BASE 0xC0000000
#define CONFIG_SYS_CPLD_RANGE 0x00000010
#define CONFIG_SYS_DUMEM_BASE 0xC0100000
#define CONFIG_SYS_DUMEM_RANGE 0x00100000
#define CONFIG_SYS_DUIO_BASE 0xC0200000
#define CONFIG_SYS_DUIO_RANGE 0x00010000
#define CONFIG_SYS_NAND0_CS 2 /* NAND chip connected to CSx */
#define CONFIG_SYS_NAND1_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x04017200
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
#define CONFIG_SYS_EBC_PB1AP 0x018003c0
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000)
/* Memory Bank 2 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x018003c0
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND0_ADDR | 0x1c000)
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x018003c0
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND1_ADDR | 0x1c000)
/* Memory Bank 4 (DUMEM, 1MB) initialization */
#define CONFIG_SYS_EBC_PB4AP 0x018053c0
#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_DUMEM_BASE | 0x18000)
/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */
#define CONFIG_SYS_EBC_PB5AP 0x018053c0
#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_DUIO_BASE | 0x18000)
/*
* NAND FLASH
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 2
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \
CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS}
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_SOURCE 1
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#endif /* __CONFIG_H */