upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/include/configs/bubinga.h

306 lines
12 KiB

/*
* (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
/*
* Include common defines/options for all AMCC eval boards
*/
#define CONFIG_HOSTNAME bubinga
#include "amcc-common.h"
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_NO_SERIAL_EEPROM
/*#undef CONFIG_NO_SERIAL_EEPROM*/
/*----------------------------------------------------------------------------*/
#ifdef CONFIG_NO_SERIAL_EEPROM
/*
!-------------------------------------------------------------------------------
! Defines for entry options.
! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that
! are plugged in the board will be utilized as non-ECC DIMMs.
!-------------------------------------------------------------------------------
*/
#define AUTO_MEMORY_CONFIG
#define DIMM_READ_ADDR 0xAB
#define DIMM_WRITE_ADDR 0xAA
/*
!-------------------------------------------------------------------------------
! PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
! assuming a 33MHz input clock to the 405EP from the C9531.
!-------------------------------------------------------------------------------
*/
#define PLLMR0_DEFAULT PLLMR0_266_133_66
#define PLLMR1_DEFAULT PLLMR1_266_133_66
#endif
/*----------------------------------------------------------------------------*/
/*
* Define here the location of the environment variables (FLASH or NVRAM).
* Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
* supported for backward compatibility.
*/
#if 1
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
/*
* Default environment variables
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_AMCC_DEF_ENV \
CONFIG_AMCC_DEF_ENV_PPC \
CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff90000\0" \
""
#define CONFIG_PHY_ADDR 1 /* PHY address */
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */
/*
* Commands additional to the ones defined in amcc-common.h
*/
#define CONFIG_CMD_DATE
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
* The Linux BASE_BAUD define should match this configuration.
* baseBaud = cpuClock/(uartDivisor*16)
* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
* set Linux BASE_BAUD to 403200.
*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CONFIG_SYS_BASE_BAUD 691200
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* avoid i2c probe hangup (?) */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#if defined(CONFIG_CMD_EEPROM)
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C boot EEPROM (24C02W) */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
#endif
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
#define CONFIG_SYS_PCI_CLASSCODE 0x0600 /* PCI Class Code: bridge/host */
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* External peripheral base address
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
*/
#define CONFIG_SYS_SRAM_BASE 0xFFF00000
#define CONFIG_SYS_SRAM_SIZE (256 << 10)
#define CONFIG_SYS_FLASH_BASE 0xFFF80000
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_ADDR0 0x5555
#define CONFIG_SYS_FLASH_ADDR1 0x2aaa
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif /* CONFIG_ENV_IS_IN_FLASH */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
#ifdef CONFIG_ENV_IS_IN_NVRAM
#define CONFIG_ENV_SIZE 0x0ff8 /* Size of Environment vars */
#define CONFIG_ENV_ADDR \
(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
#endif
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash/SRAM) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x04006000
#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 1 (NVRAM/RTC) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x04041000
#define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 2 (not used) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x00000000
#define CONFIG_SYS_EBC_PB2CR 0x00000000
/* Memory Bank 2 (not used) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x00000000
#define CONFIG_SYS_EBC_PB3CR 0x00000000
/* Memory Bank 4 (FPGA regs) initialization */
#define CONFIG_SYS_EBC_PB4AP 0x01815000
#define CONFIG_SYS_EBC_PB4CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
/*-----------------------------------------------------------------------
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
*/
#define SPD_EEPROM_ADDRESS 0x55
/*-----------------------------------------------------------------------
* Definitions for GPIO setup (PPC405EP specific)
*
* GPIO0[0] - External Bus Controller BLAST output
* GPIO0[1-9] - Instruction trace outputs
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
* GPIO0[24-27] - UART0 control signal inputs/outputs
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
#define CONFIG_SYS_GPIO0_OSRL 0x55555555
#define CONFIG_SYS_GPIO0_OSRH 0x40000110
#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
#define CONFIG_SYS_GPIO0_TSRL 0x00000000
#define CONFIG_SYS_GPIO0_TSRH 0x00000000
#define CONFIG_SYS_GPIO0_TCR 0xFFFF8014
/*-----------------------------------------------------------------------
* Some BUBINGA stuff...
*/
#define NVRAM_BASE 0xF0000000
#define FPGA_REG0 0xF0300000 /* FPGA Reg 0 */
#define FPGA_REG1 0xF0300001 /* FPGA Reg 1 */
#define NVRVFY1 0x4f532d4f /* used to determine if state data in */
#define NVRVFY2 0x50454e00 /* NVRAM initialized (ascii for OS-OPEN)*/
#define FPGA_REG0_F_RANGE 0x80 /* SDRAM PLL freq range */
#define FPGA_REG0_EXT_INT_DIS 0x20 /* External interface disable */
#define FPGA_REG0_LED_MASK 0x07 /* Board LEDs DS9, DS10, and DS11 */
#define FPGA_REG0_LED0 0x04 /* Turn on LED0 */
#define FPGA_REG0_LED1 0x02 /* Turn on LED1 */
#define FPGA_REG0_LED2 0x01 /* Turn on LED2 */
#define FPGA_REG1_SSPEC_DIS 0x80 /* C9531 Spread Spectrum disabled */
#define FPGA_REG1_OFFBD_PCICLK 0x40 /* Onboard PCI clock selected */
#define FPGA_REG1_CLOCK_MASK 0x30 /* Mask for C9531 output freq select */
#define FPGA_REG1_CLOCK_BIT_SHIFT 4
#define FPGA_REG1_PCI_INT_ARB 0x08 /* PCI Internal arbiter selected */
#define FPGA_REG1_PCI_FREQ 0x04 /* PCI Frequency select */
#define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */
#define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */
#endif /* __CONFIG_H */