upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
234 lines
7.3 KiB
234 lines
7.3 KiB
/* U-Boot for BlackVME. (C) Wojtek Skulski 2010.
|
|
* The board includes ADSP-BF561 rev. 0.5,
|
|
* 32-bit SDRAM (2 * MT48LC16M16A2TG or MT48LC32M16A2TG),
|
|
* Gigabit Ether AX88180 (ASIX) + 88E1111 rev. B2 (Marvell),
|
|
* SPI boot flash on PF2 (M25P64 8MB, or M25P128 16 MB),
|
|
* FPGA boot flash on PF3 (M25P64 8MB, or M25P128 16 MB),
|
|
* Spartan6-LX150 (memory-mapped; both PPIs also connected).
|
|
* See http://www.skutek.com
|
|
*/
|
|
|
|
#ifndef __CONFIG_BLACKVME_H__
|
|
#define __CONFIG_BLACKVME_H__
|
|
|
|
#include <asm/config-pre.h>
|
|
|
|
/* Debugging: Set these options if you're having problems
|
|
* #define CONFIG_DEBUG_EARLY_SERIAL
|
|
* #define DEBUG
|
|
* #define CONFIG_DEBUG_DUMP
|
|
* #define CONFIG_DEBUG_DUMP_SYMS
|
|
* CONFIG_PANIC_HANG means that the board will not auto-reboot
|
|
*/
|
|
#define CONFIG_PANIC_HANG 0
|
|
|
|
/* CPU Options */
|
|
#define CONFIG_BFIN_CPU bf561-0.5
|
|
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
|
|
|
|
/*
|
|
* CLOCK SETTINGS CAVEAT
|
|
* You CANNOT just change the clock settings, esp. the SCLK.
|
|
* The SDRAM timing, SPI baud, and the serial UART baud
|
|
* use SCLK frequency to set their own frequencies. Therefore,
|
|
* if you change the SCLK_DIV, you may also have to adjust
|
|
* SDRAM refresh and other timings.
|
|
* --------------------------------------------------------------
|
|
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
|
|
* 25 * 8 / 1 = 200 MHz
|
|
* 25 * 16 / 1 = 400 MHz
|
|
* 25 * 24 / 1 = 600 MHz
|
|
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
|
|
* 25 * 8 / 2 = 100 MHz
|
|
* 25 * 24 / 6 = 100 MHz
|
|
* 25 * 24 / 5 = 120 MHz
|
|
* 25 * 16 / 3 = 133 MHz
|
|
* 25 MHz because the oscillator also feeds the ether chip.
|
|
* CONFIG_CLKIN_HZ is 25 MHz written in Hz
|
|
* CLKIN_HALF controls the DF bit in PLL_CTL
|
|
* 0 = CLKIN 1 = CLKIN / 2
|
|
* PLL_BYPASS controls the BYPASS bit in PLL_CTL
|
|
* 0 = do not bypass 1 = bypass PLL
|
|
* VCO_MULT = MSEL (multiplier) in PLL_CTL
|
|
* Values can range from 0-63 (where 0 means 64)
|
|
* CCLK_DIV = core clock divider (1, 2, 4, or 8 ONLY)
|
|
* SCLK_DIV = system clock divider, 1 to 15
|
|
*/
|
|
#define CONFIG_CLKIN_HZ 25000000
|
|
#define CONFIG_CLKIN_HALF 0
|
|
#define CONFIG_PLL_BYPASS 0
|
|
#define CONFIG_VCO_MULT 8
|
|
#define CONFIG_CCLK_DIV 1
|
|
#define CONFIG_SCLK_DIV 2
|
|
|
|
/*
|
|
* Ether chip in async memory space AMS3, same as BF561-EZ-KIT.
|
|
* Used in 32-bit mode. 16-bit mode not supported.
|
|
* http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
|
|
*/
|
|
/*
|
|
* Network settings using a dedicated 2nd ether card in PC
|
|
* Windows will automatically acquire IP of that card
|
|
* Then use the dedicated card IP + 1 for the board
|
|
* http://docs.blackfin.uclinux.org/doku.php?id=setting_up_the_network
|
|
*/
|
|
#define CONFIG_DRIVER_AX88180 1
|
|
#define AX88180_BASE 0x2c000000
|
|
#define CONFIG_CMD_MII /* enable probing PHY */
|
|
|
|
#define CONFIG_HOSTNAME blackvme /* Bfin board */
|
|
#define CONFIG_IPADDR 169.254.144.145 /* Bfin board */
|
|
#define CONFIG_GATEWAYIP 169.254.144.144 /* dedic card */
|
|
#define CONFIG_SERVERIP 169.254.144.144 /* tftp server */
|
|
#define CONFIG_NETMASK 255.255.255.0
|
|
#define CONFIG_ROOTPATH "/export/uClinux-dist/romfs" /*NFS*/
|
|
#define CFG_AUTOLOAD "no"
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_PING
|
|
|
|
/*
|
|
* SDRAM settings & memory map
|
|
*/
|
|
|
|
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
|
|
#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
|
|
/*
|
|
* SDRAM reference page
|
|
* http://docs.blackfin.uclinux.org/doku.php?id=bfin:sdram
|
|
* NOTE: BlackVME populates only SDRAM bank 0
|
|
*/
|
|
/* CONFIG_EBIU_SDBCTL_VAL bank ctrl may be needed in future */
|
|
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d /* global control */
|
|
#define CONFIG_EBIU_SDRRC_VAL 0x306 /* refresh rate */
|
|
|
|
/* Async memory global settings. (ASRAM, not SDRAM)
|
|
* HRM page 16-10. Global ASRAM control = 0x3F. Six lower bits = 1
|
|
* CLKOUT enabled, all async banks enabled, core has priority
|
|
* bank 0&1 16 bit (FPGA)
|
|
* bank 2&3 32 bit (ether and USB chips)
|
|
*/
|
|
#define CONFIG_EBIU_AMGCTL_VAL 0x3F /* ASRAM setup */
|
|
|
|
/* Async mem timing: BF561 HRM page 16-12 and 16-15.
|
|
* Default values 0xFFC2 FFC2 are the slowest supported.
|
|
* Example settings of CONFIG_EBIU_AMBCTL1_VAL
|
|
* 1. EZ-KIT settings: 0xFFC2 7BB0
|
|
* 2. Bank 3 good timing for AX88180 @ 125MHz = 0x8850 xxxx
|
|
* See the following page:
|
|
* http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:ax88180
|
|
* 3. Bank 3 timing for AX88180 @ SCLK = 100 MHz:
|
|
* AX88180 WEN = 5 clocks REN 6 clocks @ SCLK = 100 MHz
|
|
* One extra clock needed because AX88180 is asynchronous to CPU.
|
|
*/
|
|
/* bank 1 0 */
|
|
#define CONFIG_EBIU_AMBCTL0_VAL 0xFFC2FFC2
|
|
/* bank 3 2 */
|
|
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC2FFC2
|
|
|
|
/* memory layout */
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
|
|
#define CONFIG_SYS_MALLOC_LEN (384 << 10)
|
|
|
|
/*
|
|
* Serial SPI Flash
|
|
* For the M25P64 SCK should be kept < 15 MHz
|
|
*/
|
|
#define CONFIG_BFIN_SPI
|
|
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
|
#define CONFIG_ENV_OFFSET 0x40000
|
|
#define CONFIG_ENV_SIZE 0x2000
|
|
#define CONFIG_ENV_SECT_SIZE 0x40000
|
|
|
|
#define CONFIG_ENV_SPI_MAX_HZ 15000000
|
|
#define CONFIG_SF_DEFAULT_SPEED 15000000
|
|
|
|
/*
|
|
* Interactive command settings
|
|
*/
|
|
|
|
#define CONFIG_SYS_LONGHELP 1
|
|
#define CONFIG_CMDLINE_EDITING 1
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
|
|
#define CONFIG_CMD_BOOTLDR
|
|
#define CONFIG_CMD_CACHE
|
|
#define CONFIG_CMD_CPLBINFO
|
|
#define CONFIG_CMD_SF
|
|
|
|
/*
|
|
* Default: boot from SPI flash.
|
|
* "sfboot" is a composite command defined in extra settings
|
|
*/
|
|
#define CONFIG_BOOTDELAY 5
|
|
#define CONFIG_BOOTCOMMAND "run sfboot"
|
|
|
|
/*
|
|
* Console settings
|
|
*/
|
|
#define CONFIG_BAUDRATE 57600
|
|
#define CONFIG_LOADS_ECHO 1
|
|
#define CONFIG_UART_CONSOLE 0
|
|
#define CONFIG_BFIN_SERIAL
|
|
|
|
/*
|
|
* U-Boot environment variables. Use "printenv" to examine.
|
|
* http://docs.blackfin.uclinux.org/doku.php?id=bootloaders:u-boot:env
|
|
*/
|
|
#define CONFIG_BOOTARGS \
|
|
"root=/dev/mtdblock0 rw " \
|
|
"clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \
|
|
"earlyprintk=serial,uart0," \
|
|
__stringify(CONFIG_BAUDRATE) " " \
|
|
"console=ttyBF0," __stringify(CONFIG_BAUDRATE) " "
|
|
|
|
/* Convenience env variables & commands.
|
|
* Reserve kernstart = 0x20000 = 128 kB for U-Boot.
|
|
* Reserve kernarea = 0x500000 = 5 MB for kernel (reasonable size).
|
|
* U-Boot image is saved at flash offset=0.
|
|
* Kernel image is saved at flash offset=$kernstart.
|
|
* Instructions. Ksave takes about a minute to complete.
|
|
* 1. Update U-Boot: run uget; run usave
|
|
* 2. Update kernel: run kget; run ksave
|
|
* After updating U-Boot also update the kernel per above instructions
|
|
* to make the saved environment consistent with the flash.
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"kernstart=0x20000\0" \
|
|
"kernarea=0x500000\0" \
|
|
"uget=tftp u-boot.ldr\0" \
|
|
"kget=tftp uImage\0" \
|
|
"usave=sf probe 2; " \
|
|
"sf erase 0 $(kernstart); " \
|
|
"sf write $(fileaddr) 0 $(filesize)\0" \
|
|
"ksave=sf probe 2; " \
|
|
"saveenv; " \
|
|
"echo Now patiently wait for the prompt...; " \
|
|
"sf erase $(kernstart) $(kernarea); " \
|
|
"sf write $(fileaddr) $(kernstart) $(filesize)\0" \
|
|
"sfboot=sf probe 2; " \
|
|
"sf read $(loadaddr) $(kernstart) $(filesize); " \
|
|
"run addip; bootm\0" \
|
|
"addip=setenv bootargs $(bootargs) " \
|
|
"ip=$(ipaddr):$(serverip):$(gatewayip):" \
|
|
"$(netmask):$(hostname):eth0:off\0"
|
|
|
|
/*
|
|
* Soft I2C settings (BF561 does not have hard I2C)
|
|
* PF12,13 on SPI connector 0.
|
|
*/
|
|
#ifdef CONFIG_SYS_I2C_SOFT
|
|
# define CONFIG_CMD_I2C
|
|
# define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF12
|
|
# define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF13
|
|
# define CONFIG_SYS_I2C_SPEED 50000
|
|
# define CONFIG_SYS_I2C_SLAVE 0xFE
|
|
#endif
|
|
|
|
/*
|
|
* No Parallel Flash on this board
|
|
*/
|
|
#define CONFIG_SYS_NO_FLASH
|
|
#undef CONFIG_CMD_JFFS2
|
|
|
|
#endif
|
|
|