upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
426 lines
14 KiB
426 lines
14 KiB
/*
|
|
* A collection of structures, addresses, and values associated with
|
|
* the Motorola 860T FADS board. Copied from the MBX stuff.
|
|
* Magnus Damm added defines for 8xxrom and extended bd_info.
|
|
* Helmut Buchsbaum added bitvalues for BCSRx
|
|
*
|
|
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
|
|
*/
|
|
|
|
/*
|
|
* 1999-nov-26: The FADS is using the following physical memorymap:
|
|
*
|
|
* ff020000 -> ff02ffff : pcmcia
|
|
* ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom
|
|
* ff000000 -> ff00ffff : IMAP internal in the cpu
|
|
* fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom
|
|
* 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom
|
|
*/
|
|
|
|
/* ------------------------------------------------------------------------- */
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
#define CONFIG_MPC850 1
|
|
#define CONFIG_MPC850SAR 1
|
|
#define CONFIG_FADS 1
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#undef CONFIG_8xx_CONS_SMC2
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
#define CONFIG_BAUDRATE 9600
|
|
|
|
#if 0
|
|
#define MPC8XX_FACT 10 /* Multiply by 10 */
|
|
#define MPC8XX_XIN 50000000 /* 50 MHz in */
|
|
#else
|
|
#define MPC8XX_FACT 12 /* Multiply by 12 */
|
|
#define MPC8XX_XIN 4000000 /* 4 MHz in */
|
|
#endif
|
|
#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
|
|
|
|
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
|
|
|
|
#if 1
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */
|
|
#define CONFIG_BOOTARGS " "
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#undef CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_PROMPT ":>" /* Monitor Command Prompt */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CFG_MEMTEST_START 0x00004000 /* memtest works on */
|
|
#define CFG_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */
|
|
|
|
#define CFG_LOAD_ADDR 0x00100000 /* default load address */
|
|
|
|
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
|
|
|
|
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CFG_IMMR 0xFF000000
|
|
#define CFG_IMMR_SIZE ((uint)(64 * 1024))
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CFG_INIT_RAM_ADDR CFG_IMMR
|
|
#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
|
|
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CFG_SDRAM_BASE _must_ start at 0
|
|
* Also NOTE that it doesn't mean SDRAM - it means MEMORY.
|
|
*/
|
|
#define CFG_SDRAM_BASE 0x00000000
|
|
#define CFG_SDRAM_SIZE (4<<20) /* standard FADS has 4M */
|
|
#define CFG_FLASH_BASE 0x02800000
|
|
#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
|
|
#if 0
|
|
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */
|
|
#else
|
|
#define CFG_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
|
|
#endif
|
|
#define CFG_MONITOR_BASE CFG_FLASH_BASE
|
|
#define CFG_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
|
|
|
|
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */
|
|
#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
|
|
#define CFG_USE_PPCENV /* Environment embedded in sect .ppcenv */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer *
|
|
* interrupt status bit - leave PLL multiplication factor unchanged !
|
|
*/
|
|
#define CFG_PLPRCR (((MPC8XX_FACT-1) << 20) | \
|
|
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#define CFG_SCCR (SCCR_TBS | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CFG_DER 0
|
|
|
|
/* Because of the way the 860 starts up and assigns CS0 the
|
|
* entire address space, we have to set the memory controller
|
|
* differently. Normally, you write the option register
|
|
* first, and then enable the chip select by writing the
|
|
* base register. For CS0, you must write the base register
|
|
* first, followed by the option register.
|
|
*/
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
/* the other CS:s are determined by looking at parameters in BCSRx */
|
|
|
|
|
|
#define BCSR_ADDR ((uint) 0x02100000)
|
|
#define BCSR_SIZE ((uint)(64 * 1024))
|
|
|
|
#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
|
|
|
|
#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
|
|
#define CFG_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */
|
|
|
|
/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
|
|
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
|
|
|
|
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
|
|
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
|
|
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
|
|
|
|
/* BCSRx - Board Control and Status Registers */
|
|
#define CFG_OR1_REMAP CFG_OR0_REMAP
|
|
#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
|
|
#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
|
|
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*/
|
|
|
|
/* periodic timer for refresh */
|
|
#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
|
|
|
|
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
|
|
#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
|
|
#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
|
|
|
|
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
|
|
#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
|
|
#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 8 column SDRAM */
|
|
#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
/* 9 column SDRAM */
|
|
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
#define CFG_MAMR 0x13a01114
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
|
|
/* values according to the manual */
|
|
|
|
|
|
#define PCMCIA_MEM_ADDR ((uint)0xff020000)
|
|
#define PCMCIA_MEM_SIZE ((uint)(64 * 1024))
|
|
|
|
#define BCSR0 ((uint) (BCSR_ADDR + 00))
|
|
#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
|
|
#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
|
|
#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
|
|
#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
|
|
|
|
/* FADS bitvalues by Helmut Buchsbaum
|
|
* see MPC8xxADS User's Manual for a proper description
|
|
* of the following structures
|
|
*/
|
|
|
|
#define BCSR0_ERB ((uint)0x80000000)
|
|
#define BCSR0_IP ((uint)0x40000000)
|
|
#define BCSR0_BDIS ((uint)0x10000000)
|
|
#define BCSR0_BPS_MASK ((uint)0x0C000000)
|
|
#define BCSR0_ISB_MASK ((uint)0x01800000)
|
|
#define BCSR0_DBGC_MASK ((uint)0x00600000)
|
|
#define BCSR0_DBPC_MASK ((uint)0x00180000)
|
|
#define BCSR0_EBDF_MASK ((uint)0x00060000)
|
|
|
|
#define BCSR1_FLASH_EN ((uint)0x80000000)
|
|
#define BCSR1_DRAM_EN ((uint)0x40000000)
|
|
#define BCSR1_ETHEN ((uint)0x20000000)
|
|
#define BCSR1_IRDEN ((uint)0x10000000)
|
|
#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
|
|
#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
|
|
#define BCSR1_BCSR_EN ((uint)0x02000000)
|
|
#define BCSR1_RS232EN_1 ((uint)0x01000000)
|
|
#define BCSR1_PCCEN ((uint)0x00800000)
|
|
#define BCSR1_PCCVCC0 ((uint)0x00400000)
|
|
#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
|
|
#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
|
|
#define BCSR1_RS232EN_2 ((uint)0x00040000)
|
|
#define BCSR1_SDRAM_EN ((uint)0x00020000)
|
|
#define BCSR1_PCCVCC1 ((uint)0x00010000)
|
|
|
|
#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
|
|
#define BCSR2_FLASH_PD_SHIFT 28
|
|
#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
|
|
#define BCSR2_DRAM_PD_SHIFT 23
|
|
#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
|
|
#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
|
|
|
|
#define BCSR3_DBID_MASK ((ushort)0x3800)
|
|
#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
|
|
#define BCSR3_BREVNR0 ((ushort)0x0080)
|
|
#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
|
|
#define BCSR3_BREVN1 ((ushort)0x0008)
|
|
#define BCSR3_BREVN2_MASK ((ushort)0x0003)
|
|
|
|
#define BCSR4_ETHLOOP ((uint)0x80000000)
|
|
#define BCSR4_TFPLDL ((uint)0x40000000)
|
|
#define BCSR4_TPSQEL ((uint)0x20000000)
|
|
#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_USB_EN ((uint)0x08000000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC860SAR
|
|
#define BCSR4_UTOPIA_EN ((uint)0x08000000)
|
|
#endif /* CONFIG_MPC860SAR */
|
|
#ifdef CONFIG_MPC860T
|
|
#define BCSR4_FETH_EN ((uint)0x08000000)
|
|
#endif /* CONFIG_MPC860T */
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_USB_SPEED ((uint)0x04000000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC860T
|
|
#define BCSR4_FETHCFG0 ((uint)0x04000000)
|
|
#endif /* CONFIG_MPC860T */
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_VCCO ((uint)0x02000000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC860T
|
|
#define BCSR4_FETHFDE ((uint)0x02000000)
|
|
#endif /* CONFIG_MPC860T */
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_VIDEO_ON ((uint)0x00800000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC860T
|
|
#define BCSR4_FETHCFG1 ((uint)0x00400000)
|
|
#endif /* CONFIG_MPC860T */
|
|
#ifdef CONFIG_MPC823
|
|
#define BCSR4_VIDEO_RST ((uint)0x00200000)
|
|
#endif /* CONFIG_MPC823 */
|
|
#ifdef CONFIG_MPC860T
|
|
#define BCSR4_FETHRST ((uint)0x00200000)
|
|
#endif /* CONFIG_MPC860T */
|
|
#define BCSR4_MODEM_EN ((uint)0x00100000)
|
|
#define BCSR4_DATA_VOICE ((uint)0x00080000)
|
|
|
|
#define CONFIG_DRAM_50MHZ 1
|
|
#define CONFIG_SDRAM_50MHZ
|
|
|
|
/* We don't use the 8259.
|
|
*/
|
|
#define NR_8259_INTS 0
|
|
|
|
#define CONFIG_DISK_SPINUP_TIME 1000000
|
|
|
|
|
|
/* PCMCIA configuration */
|
|
|
|
#define PCMCIA_MAX_SLOTS 2
|
|
|
|
#ifdef CONFIG_MPC860
|
|
#define PCMCIA_SLOT_A 1
|
|
#endif
|
|
|
|
#define CFG_DAUGHTERBOARD
|
|
|
|
#endif /* __CONFIG_H */
|
|
|