upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
271 lines
9.0 KiB
271 lines
9.0 KiB
/*
|
|
* (C) Copyright 2011 HALE electronic <helmut.raiger@hale.at>
|
|
* (C) Copyright 2008 Magnus Lilja <lilja.magnus@gmail.com>
|
|
*
|
|
* Configuration settings for the HALE TT-01 board.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#include <asm/arch/imx-regs.h>
|
|
|
|
/* High Level Configuration Options */
|
|
#define CONFIG_MX31
|
|
|
|
#define CONFIG_DISPLAY_CPUINFO
|
|
#define CONFIG_DISPLAY_BOARDINFO
|
|
|
|
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
|
|
#define CONFIG_SETUP_MEMORY_TAGS
|
|
#define CONFIG_INITRD_TAG
|
|
|
|
#define CONFIG_MACH_TYPE 3726 /* not yet in mach-types.h */
|
|
#define CONFIG_SYS_TEXT_BASE 0xA0000000
|
|
|
|
|
|
/*
|
|
* Physical Memory Map:
|
|
* CS settings are defined by i.MX31:
|
|
* - CSD0 and CDS1 are 256MB each, starting at 0x80000000 and 0x9000000
|
|
* - CS0 and CS1 are 128MB each, at A0000000 and A8000000
|
|
* - CS2 to CS5 are 32MB each, at B0.., B2.., B4.., B6..
|
|
*
|
|
* HALE set-up of the bluetechnix board for now is:
|
|
* - 128MB DDR (2x64MB, 2x16bit), connected to 32bit DDR ram interface
|
|
* - NOR-Flash (Spansion 32MB MCP, Flash+16MB PSRAM), 16bit interface at CS0
|
|
* - S71WS256ND0BFWYM (and CS1 for 64MB S71WS512ND0 without PSRAM)
|
|
* the flash chip is a mirrorbit S29WS256N !
|
|
* - the PSRAM is hooked to CS5 (0xB6000000)
|
|
* - Intel Strata Flash PF48F2000P0ZB00, 16bit interface at (CS0 or) CS1
|
|
* - 64Mbit = 8MByte (will go away in the production set-up)
|
|
* - NAND-Flash NAND01GR3B2BZA6 at NAND-FC:
|
|
* 1Gbit=128MB, 2048+64 bytes/page, 64pages x 1024 blocks
|
|
* - Ethernet controller SMC9118 at CS4 via FPGA, 16bit interface
|
|
*
|
|
* u-boot will support the 32MB nor flash and the 128MB NAND flash, the PSRAM
|
|
* is not used right now. We should be able to reduce the SOM to NAND flash
|
|
* only and boot from there.
|
|
*/
|
|
#define CONFIG_NR_DRAM_BANKS 1
|
|
#define PHYS_SDRAM_1 CSD0_BASE
|
|
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F
|
|
#define CONFIG_BOARD_LATE_INIT
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
|
|
|
|
/* default load address, 1MB up the road */
|
|
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1+0x100000)
|
|
|
|
/* Size of malloc() pool, make sure possible frame buffer fits */
|
|
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 10*1024*1024)
|
|
|
|
/* memtest works on all but the last 1MB (u-boot) and malloc area */
|
|
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
|
|
#define CONFIG_SYS_MEMTEST_END \
|
|
(PHYS_SDRAM_1+(PHYS_SDRAM_1_SIZE-CONFIG_SYS_MALLOC_LEN-0x100000))
|
|
|
|
/* CFI FLASH driver setup */
|
|
#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
|
|
#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
|
|
#define CONFIG_FLASH_SPANSION_S29WS_N
|
|
/*
|
|
* TODO: Bluetechnix (the supplier of the SOM) did define these values
|
|
* in their original version of u-boot (1.2 or so). This should be
|
|
* reviewed.
|
|
*
|
|
* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
|
|
* #define CONFIG_SYS_FLASH_PROTECTION
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE CS0_BASE
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT (254+8) /* max number of sectors per chip */
|
|
|
|
/*
|
|
* FLASH and environment organization, only the Spansion chip is supported:
|
|
* - it has 254 * 128kB + 8 * 32kB blocks
|
|
* - this setup uses 4*32k+3*128k as monitor space = 0xA000 0000 to 0xA00F FFFF
|
|
* and 2 sectors with 128k as environment =
|
|
* A010 0000 to 0xA011 FFFF and 0xA012 0000 to 0xA013 FFFF
|
|
* - this could be less, but this is only for developer versions of the board
|
|
* and no-one is going to use the NOR flash anyway.
|
|
*
|
|
* Monitor is at the beginning of the NOR-Flash, 1MB reserved. Again this is
|
|
* way to large, but it avoids ENV overwrite (when updating u-boot) in case
|
|
* size breaks the next boundary (as it has with 128k).
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MONITOR_LEN (1024 * 1024)
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH
|
|
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
|
|
#define CONFIG_ENV_SIZE (128 * 1024)
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
|
|
|
|
/* Hardware drivers */
|
|
|
|
/*
|
|
* on TT-01 UART1 pins are used by Audio, so we use UART2
|
|
* TT-01 implements a hardware that turns off components depending on
|
|
* the power level. In PL=1 the RS232 transceiver is usually off,
|
|
* make sure that the transceiver is enabled during PL=1 for testing!
|
|
*/
|
|
#define CONFIG_MXC_UART
|
|
#define CONFIG_MXC_UART_BASE UART2_BASE
|
|
|
|
#define CONFIG_MXC_SPI
|
|
#define CONFIG_MXC_GPIO
|
|
|
|
/* MC13783 connected to CSPI3 and SS0 */
|
|
#define CONFIG_POWER
|
|
#define CONFIG_POWER_SPI
|
|
#define CONFIG_POWER_FSL
|
|
|
|
#define CONFIG_FSL_PMIC_BUS 2
|
|
#define CONFIG_FSL_PMIC_CS 0
|
|
#define CONFIG_FSL_PMIC_CLK 1000000
|
|
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
|
|
#define CONFIG_FSL_PMIC_BITLEN 32
|
|
|
|
#define CONFIG_RTC_MC13XXX
|
|
|
|
/* allow to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
/* console is UART2 on TT-01 */
|
|
#define CONFIG_CONS_INDEX 1
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/* ethernet setup for the onboard smc9118 */
|
|
#define CONFIG_MII
|
|
#define CONFIG_SMC911X
|
|
/* 16 bit, onboard ethernet, decoded via MACH-MX0 FPGA at 0x84200000 */
|
|
#define CONFIG_SMC911X_BASE (CS4_BASE+0x200000)
|
|
#define CONFIG_SMC911X_16_BIT
|
|
|
|
/* mmc driver */
|
|
#define CONFIG_MMC
|
|
#define CONFIG_GENERIC_MMC
|
|
#define CONFIG_MXC_MMC
|
|
#define CONFIG_MXC_MCI_REGS_BASE SDHC1_BASE_ADDR
|
|
|
|
/* video support */
|
|
#define CONFIG_VIDEO
|
|
#define CONFIG_VIDEO_MX3
|
|
#define CONFIG_CFB_CONSOLE
|
|
#define CONFIG_VIDEO_LOGO
|
|
/* splash image won't work with NAND boot, use preboot script */
|
|
#define CONFIG_VIDEO_SW_CURSOR
|
|
#define CONFIG_CONSOLE_EXTRA_INFO /* display additional board info */
|
|
#define CONFIG_VGA_AS_SINGLE_DEVICE /* display is an output only device */
|
|
|
|
/* allow stdin, stdout and stderr variables to redirect output */
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
#define CONFIG_SILENT_CONSOLE /* UARTs used externally (release) */
|
|
#define CONFIG_SYS_DEVICE_NULLDEV /* allow console to be turned off */
|
|
#define CONFIG_PREBOOT
|
|
|
|
/* allow decompressing max. 4MB */
|
|
#define CONFIG_VIDEO_BMP_GZIP
|
|
/* this is not only used by cfb_console.c for the logo, but also in cmd_bmp.c */
|
|
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4*1024*1024)
|
|
|
|
/*
|
|
* Command definition
|
|
*/
|
|
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_SAVEENV
|
|
#define CONFIG_CMD_NAND
|
|
/*
|
|
* #define CONFIG_CMD_NAND_LOCK_UNLOCK the NAND01... chip does not support
|
|
* the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports
|
|
* a software locking scheme.
|
|
*/
|
|
#define CONFIG_CMD_BMP
|
|
|
|
#define CONFIG_BOOTDELAY 3
|
|
|
|
/*
|
|
* currently a default setting for booting via script is implemented
|
|
* set user to login name and serverip to tftp host, define your
|
|
* boot behaviour in bootscript.loginname
|
|
*
|
|
* TT-01 board specific TFT setup (used by drivers/video/mx3fb.c)
|
|
*
|
|
* This set-up is for the L5F30947T04 by Epson, which is
|
|
* 800x480, 33MHz pixel clock, 60Hz vsync, 31.6kHz hsync
|
|
* sync must be set to: DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"videomode=epson\0" \
|
|
"epson=video=ctfb:x:800,y:480,depth:16,mode:0,pclk:30076," \
|
|
"le:215,ri:1,up:32,lo:13,hs:7,vs:10,sync:100663296,vmode:0\0" \
|
|
"bootcmd=dhcp bootscript.${user}; source\0"
|
|
|
|
#define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */
|
|
#define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */
|
|
|
|
/* Miscellaneous configurable options */
|
|
#define CONFIG_SYS_HUSH_PARSER
|
|
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#define CONFIG_SYS_PROMPT "TT01> "
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
|
|
sizeof(CONFIG_SYS_PROMPT)+16)
|
|
/* max number of command args */
|
|
#define CONFIG_SYS_MAXARGS 16
|
|
/* Boot Argument Buffer Size */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
|
|
#define CONFIG_CMDLINE_EDITING
|
|
|
|
/* MMC boot support */
|
|
#define CONFIG_CMD_MMC
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_EFI_PARTITION
|
|
#define CONFIG_CMD_EXT2
|
|
#define CONFIG_CMD_FAT
|
|
|
|
#define CONFIG_NAND_MXC
|
|
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
|
|
/*
|
|
* actually this is nothing someone wants to configure!
|
|
* CONFIG_SYS_NAND_BASE despite being passed to board_nand_init()
|
|
* is not used by the driver.
|
|
*/
|
|
#define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR
|
|
#define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR
|
|
#define CONFIG_MXC_NAND_HWECC
|
|
|
|
/* the current u-boot driver does not use the nand flash setup! */
|
|
#define CONFIG_SYS_NAND_LARGEPAGE
|
|
/*
|
|
* it's not 16 bit:
|
|
* #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
|
|
* the current u-boot mxc_nand.c tries to auto-detect, but this only
|
|
* reads the boot settings during reset (which might be wrong)
|
|
*/
|
|
|
|
#endif /* __CONFIG_H */
|
|
|