upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
542 lines
16 KiB
542 lines
16 KiB
/*
|
|
* -- Version 1.1 --
|
|
*
|
|
* (C) Copyright 2003-2005
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* (C) Copyright 2004-2005
|
|
* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
|
|
*
|
|
* (C) Copyright 2005
|
|
* Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de.
|
|
*
|
|
* History:
|
|
* 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
|
|
#define CONFIG_MPC5200 1 /* (more precisely a MPC5200 CPU) */
|
|
#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */
|
|
|
|
#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */
|
|
#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */
|
|
#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */
|
|
#define CONFIG_BC3450_USB 1 /* + USB support */
|
|
# define CONFIG_FAT 1 /* + FAT support */
|
|
# define CONFIG_EXT2 1 /* + EXT2 support */
|
|
#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */
|
|
#undef CONFIG_BC3450_CAN /* + CAN transceiver */
|
|
#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */
|
|
#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */
|
|
#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */
|
|
#define CONFIG_BC3450_FP 1 /* + enable FP O/P */
|
|
#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */
|
|
|
|
/*
|
|
* Valid values for CONFIG_SYS_TEXT_BASE are:
|
|
* 0xFC000000 boot low (standard configuration with room for
|
|
* max 64 MByte Flash ROM)
|
|
* 0x00100000 boot from RAM (for testing only)
|
|
*/
|
|
#ifndef CONFIG_SYS_TEXT_BASE
|
|
#define CONFIG_SYS_TEXT_BASE 0xFC000000
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
|
|
|
|
#define CONFIG_HIGH_BATS 1 /* High BATs supported */
|
|
|
|
/*
|
|
* Serial console configuration
|
|
*/
|
|
#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
|
|
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
|
|
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
|
|
|
|
/*
|
|
* AT-PS/2 Multiplexer
|
|
*/
|
|
#ifdef CONFIG_BC3450_PS2
|
|
# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
|
|
# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
|
|
# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */
|
|
# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */
|
|
# define CONFIG_BOARD_EARLY_INIT_R
|
|
#endif /* CONFIG_BC3450_PS2 */
|
|
|
|
/*
|
|
* PCI Mapping:
|
|
* 0x40000000 - 0x4fffffff - PCI Memory
|
|
* 0x50000000 - 0x50ffffff - PCI IO Space
|
|
*/
|
|
# define CONFIG_PCI 1
|
|
# define CONFIG_PCI_PNP 1
|
|
/* #define CONFIG_PCI_SCAN_SHOW 1 */
|
|
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
|
|
|
|
#define CONFIG_PCI_MEM_BUS 0x40000000
|
|
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
|
|
#define CONFIG_PCI_MEM_SIZE 0x10000000
|
|
|
|
#define CONFIG_PCI_IO_BUS 0x50000000
|
|
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
|
|
#define CONFIG_PCI_IO_SIZE 0x01000000
|
|
|
|
/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */
|
|
#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
|
|
#define CONFIG_NS8382X 1
|
|
|
|
/*
|
|
* Video console
|
|
*/
|
|
# define CONFIG_VIDEO
|
|
# define CONFIG_VIDEO_SM501
|
|
# define CONFIG_VIDEO_SM501_32BPP
|
|
# define CONFIG_CFB_CONSOLE
|
|
# define CONFIG_VIDEO_LOGO
|
|
# define CONFIG_VGA_AS_SINGLE_DEVICE
|
|
# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */
|
|
# define CONFIG_VIDEO_SW_CURSOR
|
|
# define CONFIG_SPLASH_SCREEN
|
|
# define CONFIG_SYS_CONSOLE_IS_IN_ENV
|
|
|
|
/*
|
|
* Partitions
|
|
*/
|
|
#define CONFIG_MAC_PARTITION
|
|
#define CONFIG_DOS_PARTITION
|
|
#define CONFIG_ISO_PARTITION
|
|
|
|
/*
|
|
* USB
|
|
*/
|
|
#ifdef CONFIG_BC3450_USB
|
|
# define CONFIG_USB_OHCI
|
|
# define CONFIG_USB_STORAGE
|
|
#endif /* CONFIG_BC3450_USB */
|
|
|
|
/*
|
|
* POST support
|
|
*/
|
|
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
|
|
CONFIG_SYS_POST_CPU | \
|
|
CONFIG_SYS_POST_I2C)
|
|
|
|
#ifdef CONFIG_POST
|
|
/* preserve space for the post_word at end of on-chip SRAM */
|
|
# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
|
|
#endif /* CONFIG_POST */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_ECHO
|
|
#define CONFIG_CMD_EEPROM
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_JFFS2
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_NFS
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_REGINFO
|
|
#define CONFIG_CMD_SNTP
|
|
#define CONFIG_CMD_BSP
|
|
|
|
#ifdef CONFIG_VIDEO
|
|
#define CONFIG_CMD_BMP
|
|
#endif
|
|
|
|
#ifdef CONFIG_BC3450_IDE
|
|
#define CONFIG_CMD_IDE
|
|
#endif
|
|
|
|
#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB)
|
|
#ifdef CONFIG_FAT
|
|
#define CONFIG_CMD_FAT
|
|
#endif
|
|
|
|
#ifdef CONFIG_EXT2
|
|
#define CONFIG_CMD_EXT2
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef CONFIG_BC3450_USB
|
|
#define CONFIG_CMD_USB
|
|
#endif
|
|
|
|
#ifdef CONFIG_PCI
|
|
#define CONFIG_CMD_PCI
|
|
#endif
|
|
|
|
#ifdef CONFIG_POST
|
|
#define CONFIG_CMD_DIAG
|
|
#endif
|
|
|
|
|
|
#define CONFIG_TIMESTAMP /* display image timestamps */
|
|
|
|
#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */
|
|
# define CONFIG_SYS_LOWBOOT 1
|
|
#endif
|
|
|
|
/*
|
|
* Autobooting
|
|
*/
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
|
|
"echo;"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"ipaddr=192.168.1.10\0" \
|
|
"serverip=192.168.1.3\0" \
|
|
"netmask=255.255.255.0\0" \
|
|
"hostname=bc3450\0" \
|
|
"rootpath=/opt/eldk/ppc_6xx\0" \
|
|
"kernel_addr=fc0a0000\0" \
|
|
"ramdisk_addr=fc1c0000\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$(serverip):$(rootpath)\0" \
|
|
"ideargs=setenv bootargs root=/dev/hda2 ro\0" \
|
|
"addip=setenv bootargs $(bootargs) " \
|
|
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
|
|
":$(hostname):$(netdev):off panic=1\0" \
|
|
"addcons=setenv bootargs $(bootargs) " \
|
|
"console=ttyS0,$(baudrate) console=tty0\0" \
|
|
"flash_self=run ramargs addip addcons;" \
|
|
"bootm $(kernel_addr) $(ramdisk_addr)\0" \
|
|
"flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \
|
|
"net_nfs=tftp 200000 $(bootfile); " \
|
|
"run nfsargs addip addcons; bootm\0" \
|
|
"ide_nfs=run nfsargs addip addcons; " \
|
|
"disk 200000 0:1; bootm\0" \
|
|
"ide_ide=run ideargs addip addcons; " \
|
|
"disk 200000 0:1; bootm\0" \
|
|
"usb_self=run usbload; run ramargs addip addcons; " \
|
|
"bootm 200000 400000\0" \
|
|
"usbload=usb reset; usb scan; usbboot 200000 0:1; " \
|
|
"usbboot 400000 0:2\0" \
|
|
"bootfile=uImage\0" \
|
|
"load=tftp 200000 $(u-boot)\0" \
|
|
"u-boot=u-boot.bin\0" \
|
|
"update=protect off FC000000 FC05FFFF;" \
|
|
"erase FC000000 FC05FFFF;" \
|
|
"cp.b 200000 FC000000 $(filesize);" \
|
|
"protect on FC000000 FC05FFFF\0" \
|
|
""
|
|
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
/*
|
|
* IPB Bus clocking configuration.
|
|
*/
|
|
#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
|
|
|
|
/*
|
|
* PCI Bus clocking configuration
|
|
*
|
|
* Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
|
|
* CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
|
|
* of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
|
|
*/
|
|
#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
|
|
# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
|
|
#endif
|
|
|
|
/*
|
|
* I2C configuration
|
|
*/
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */
|
|
|
|
/*
|
|
* I2C clock frequency
|
|
*
|
|
* Please notice, that the resulting clock frequency could differ from the
|
|
* configured value. This is because the I2C clock is derived from system
|
|
* clock over a frequency divider with only a few divider values. U-boot
|
|
* calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
|
|
* approximation allways lies below the configured value, never above.
|
|
*/
|
|
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
/*
|
|
* EEPROM configuration for I²C EEPROM M24C32
|
|
* M24C64 should work also. For other EEPROMs config should be verified.
|
|
*
|
|
* The TQM5200 module may hold an EEPROM at address 0x50.
|
|
*/
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
|
|
|
|
/*
|
|
* RTC configuration
|
|
*/
|
|
#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231)
|
|
# define CONFIG_RTC_M41T11 1
|
|
# define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
|
#else
|
|
# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */
|
|
# define CONFIG_BOARD_EARLY_INIT_R
|
|
#endif
|
|
|
|
/*
|
|
* Flash configuration
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
|
|
|
|
/* use CFI flash driver if no module variant is spezified */
|
|
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
|
|
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
|
|
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
|
|
#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */
|
|
|
|
#if !defined(CONFIG_SYS_LOWBOOT)
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
|
|
#else /* CONFIG_SYS_LOWBOOT */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000)
|
|
#endif /* CONFIG_SYS_LOWBOOT */
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks
|
|
(= chip selects) */
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
|
|
|
|
/* Dynamic MTD partition support */
|
|
#define CONFIG_CMD_MTDPARTS
|
|
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
|
|
#define CONFIG_FLASH_CFI_MTD
|
|
#define MTDIDS_DEFAULT "nor0=TQM5200-0"
|
|
#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \
|
|
"1408k(kernel)," \
|
|
"2m(initrd)," \
|
|
"4m(small-fs)," \
|
|
"16m(big-fs)," \
|
|
"8m(misc)"
|
|
|
|
/*
|
|
* Environment settings
|
|
*/
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_SIZE 0x10000
|
|
#define CONFIG_ENV_SECT_SIZE 0x20000
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
|
|
/*
|
|
* Memory map
|
|
*/
|
|
#define CONFIG_SYS_MBAR 0xF0000000
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
|
|
|
|
/* Use ON-Chip SRAM until RAM will be available */
|
|
#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
|
|
#ifdef CONFIG_POST
|
|
/* preserve space for the post_word at end of on-chip SRAM */
|
|
# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
|
|
#else
|
|
# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
|
|
#endif /*CONFIG_POST*/
|
|
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
# define CONFIG_SYS_RAMBOOT 1
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*
|
|
* Ethernet configuration
|
|
*
|
|
* Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT
|
|
*/
|
|
#define CONFIG_MPC5xxx_FEC 1
|
|
#define CONFIG_MPC5xxx_FEC_MII100
|
|
#undef CONFIG_MPC5xxx_MII10
|
|
#define CONFIG_PHY_ADDR 0x00
|
|
|
|
/*
|
|
* GPIO configuration on BC3450
|
|
*
|
|
* PSC1: UART1 (Service-UART) [0x xxxxxxx4]
|
|
* PSC2: UART2 [0x xxxxxx4x]
|
|
* or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x]
|
|
* PSC3: USB2 [0x xxxxx1xx]
|
|
* USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx]
|
|
* (this has to match
|
|
* CONFIG_USB_CONFIG which is
|
|
* used by usb_ohci.c to set
|
|
* the USB ports)
|
|
* Eth: 10/100Mbit Ethernet [0x xxx0xxxx]
|
|
* (this is reset to '5'
|
|
* in FEC driver: fec.c)
|
|
* PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx]
|
|
* ATA/CS: ??? [0x x1xxxxxx]
|
|
* FIXME! UM Fig 2-10 suggests [0x x0xxxxxx]
|
|
* CS1: Use Pin gpio_wkup_6 as second
|
|
* SDRAM chip select (mem_cs1)
|
|
* Timer: CAN2 / SPI
|
|
* I2C: CAN1 / I²C2 [0x bxxxxxxx]
|
|
*/
|
|
#ifdef CONFIG_BC3450_AC97
|
|
# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124
|
|
#else /* PSC2=UART2 */
|
|
# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144
|
|
#endif
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max no of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */
|
|
|
|
#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */
|
|
/* more extensive mem test */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*
|
|
* Enable loopw command.
|
|
*/
|
|
#define CONFIG_LOOPW
|
|
|
|
/*
|
|
* Various low-level settings
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
|
|
#define CONFIG_SYS_HID0_FINAL HID0_ICE
|
|
|
|
#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
|
|
#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
|
|
# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */
|
|
#else
|
|
# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */
|
|
#endif
|
|
#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
|
|
|
|
/* automatic configuration of chip selects */
|
|
#ifdef CONFIG_TQM5200
|
|
# define CONFIG_LAST_STAGE_INIT
|
|
#endif /* CONFIG_TQM5200 */
|
|
|
|
/*
|
|
* SRAM - Do not map below 2 GB in address space, because this area is used
|
|
* for SDRAM autosizing.
|
|
*/
|
|
#ifdef CONFIG_TQM5200
|
|
# define CONFIG_SYS_CS2_START 0xE5000000
|
|
# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */
|
|
# define CONFIG_SYS_CS2_CFG 0x0004D930
|
|
#endif /* CONFIG_TQM5200 */
|
|
|
|
/*
|
|
* Grafic controller - Do not map below 2 GB in address space, because this
|
|
* area is used for SDRAM autosizing.
|
|
*/
|
|
#ifdef CONFIG_TQM5200
|
|
# define SM501_FB_BASE 0xE0000000
|
|
# define CONFIG_SYS_CS1_START (SM501_FB_BASE)
|
|
# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */
|
|
# define CONFIG_SYS_CS1_CFG 0x8F48FF70
|
|
# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000
|
|
#endif /* CONFIG_TQM5200 */
|
|
|
|
#define CONFIG_SYS_CS_BURST 0x00000000
|
|
#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */
|
|
/* flash and SM501 */
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0xff000000
|
|
|
|
/*
|
|
* USB stuff
|
|
*/
|
|
#define CONFIG_USB_CLOCK 0x0001BBBB
|
|
#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */
|
|
|
|
/*
|
|
* IDE/ATA stuff Supports IDE harddisk
|
|
*/
|
|
#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
|
|
|
|
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
|
|
#define CONFIG_IDE_RESET /* reset for ide supported */
|
|
#define CONFIG_IDE_PREINIT
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
|
|
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
|
|
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
|
|
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
|
|
|
|
/* Interval between registers */
|
|
#define CONFIG_SYS_ATA_STRIDE 4
|
|
|
|
#endif /* __CONFIG_H */
|
|
|