upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
413 lines
11 KiB
413 lines
11 KiB
/*
|
|
* (C) Copyright 2009
|
|
* Marvell Semiconductor <www.marvell.com>
|
|
* Prafulla Wadaskar <prafulla@marvell.com>
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
|
|
* MA 02110-1301 USA
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <netdev.h>
|
|
#include "mv88e61xx.h"
|
|
|
|
#ifdef CONFIG_MV88E61XX_MULTICHIP_ADRMODE
|
|
/* Chip Address mode
|
|
* The Switch support two modes of operation
|
|
* 1. single chip mode and
|
|
* 2. Multi-chip mode
|
|
* Refer section 9.2 &9.3 in chip datasheet-02 for more details
|
|
*
|
|
* By default single chip mode is configured
|
|
* multichip mode operation can be configured in board header
|
|
*/
|
|
static int mv88e61xx_busychk_multic(u32 devaddr)
|
|
{
|
|
u32 reg = 0;
|
|
u32 timeout = MV88E61XX_PHY_TIMEOUT;
|
|
|
|
/* Poll till SMIBusy bit is clear */
|
|
do {
|
|
miiphy_read(name, devaddr, 0x0, ®);
|
|
if (timeout-- == 0) {
|
|
printf("SMI busy timeout\n");
|
|
return -1;
|
|
}
|
|
} while (reg & (1 << 15));
|
|
return 0;
|
|
}
|
|
|
|
static void mv88e61xx_wr_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 data)
|
|
{
|
|
u16 reg;
|
|
u32 mii_dev_addr;
|
|
|
|
/* command to read PHY dev address */
|
|
if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
|
|
printf("Error..could not read PHY dev address\n");
|
|
return;
|
|
}
|
|
mv88e61xx_busychk_multic(mii_dev_addr);
|
|
/* Write data to Switch indirect data register */
|
|
miiphy_write(name, mii_dev_addr, 0x1, data);
|
|
/* Write command to Switch indirect command register (write) */
|
|
miiphy_write(name, mii_dev_addr, 0x0,
|
|
reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
|
|
15));
|
|
}
|
|
|
|
static void mv88e61xx_rd_phy(char *name, u32 phy_adr, u32 reg_ofs, u16 * data)
|
|
{
|
|
u16 reg;
|
|
u32 mii_dev_addr;
|
|
|
|
/* command to read PHY dev address */
|
|
if (!miiphy_read(name, 0xEE, 0xEE, &mii_dev_addr)) {
|
|
printf("Error..could not read PHY dev address\n");
|
|
return;
|
|
}
|
|
mv88e61xx_busychk_multic(mii_dev_addr);
|
|
/* Write command to Switch indirect command register (read) */
|
|
miiphy_write(name, mii_dev_addr, 0x0,
|
|
reg_ofs | (phy_adr << 5) | (1 << 10) | (1 << 12) | (1 <<
|
|
15));
|
|
mv88e61xx_busychk_multic(mii_dev_addr);
|
|
/* Read data from Switch indirect data register */
|
|
miiphy_read(name, mii_dev_addr, 0x1, (u16 *) & data);
|
|
}
|
|
#endif /* CONFIG_MV88E61XX_MULTICHIP_ADRMODE */
|
|
|
|
static void mv88e61xx_port_vlan_config(struct mv88e61xx_config *swconfig,
|
|
u32 max_prtnum, u32 ports_ofs)
|
|
{
|
|
u32 prt;
|
|
u16 reg;
|
|
char *name = swconfig->name;
|
|
u32 cpu_port = swconfig->cpuport;
|
|
u32 port_mask = swconfig->ports_enabled;
|
|
enum mv88e61xx_cfg_vlan vlancfg = swconfig->vlancfg;
|
|
|
|
/* be sure all ports are disabled */
|
|
for (prt = 0; prt < max_prtnum; prt++) {
|
|
RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, ®);
|
|
reg &= ~0x3;
|
|
WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_CTRL_REG, reg);
|
|
|
|
if (!(cpu_port & (1 << prt)))
|
|
continue;
|
|
/* Set CPU port VID to 0x1 */
|
|
RD_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, ®);
|
|
reg &= ~0xfff;
|
|
reg |= 0x1;
|
|
WR_PHY(name, (ports_ofs + prt), MV88E61XX_PRT_VID_REG, reg);
|
|
}
|
|
|
|
/* Setting Port default priority for all ports to zero */
|
|
for (prt = 0; prt < max_prtnum; prt++) {
|
|
RD_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, ®);
|
|
reg &= ~0xc000;
|
|
WR_PHY(name, ports_ofs + prt, MV88E61XX_PRT_VID_REG, reg);
|
|
}
|
|
/* Setting VID and VID map for all ports except CPU port */
|
|
for (prt = 0; prt < max_prtnum; prt++) {
|
|
/* only for enabled ports */
|
|
if ((1 << prt) & port_mask) {
|
|
/* skip CPU port */
|
|
if ((1 << prt) & cpu_port) {
|
|
/*
|
|
* Set Vlan map table for cpu_port to see
|
|
* all ports
|
|
*/
|
|
RD_PHY(name, (ports_ofs + prt),
|
|
MV88E61XX_PRT_VMAP_REG, ®);
|
|
reg &= ~((1 << max_prtnum) - 1);
|
|
reg |= port_mask & ~(1 << prt);
|
|
WR_PHY(name, (ports_ofs + prt),
|
|
MV88E61XX_PRT_VMAP_REG, reg);
|
|
} else {
|
|
|
|
/*
|
|
* set Ports VLAN Mapping.
|
|
* port prt <--> cpu_port VLAN #prt+1.
|
|
*/
|
|
RD_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_VID_REG, ®);
|
|
reg &= ~0x0fff;
|
|
reg |= (prt + 1);
|
|
WR_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_VID_REG, reg);
|
|
|
|
RD_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_VMAP_REG, ®);
|
|
if (vlancfg == MV88E61XX_VLANCFG_DEFAULT) {
|
|
/*
|
|
* all any port can send frames to all other ports
|
|
* ref: sec 3.2.1.1 of datasheet
|
|
*/
|
|
reg |= 0x03f;
|
|
reg &= ~(1 << prt);
|
|
} else if (vlancfg == MV88E61XX_VLANCFG_ROUTER) {
|
|
/*
|
|
* all other ports can send frames to CPU port only
|
|
* ref: sec 3.2.1.2 of datasheet
|
|
*/
|
|
reg &= ~((1 << max_prtnum) - 1);
|
|
reg |= cpu_port;
|
|
}
|
|
WR_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_VMAP_REG, reg);
|
|
}
|
|
}
|
|
}
|
|
|
|
/*
|
|
* enable only appropriate ports to forwarding mode
|
|
* and disable the others
|
|
*/
|
|
for (prt = 0; prt < max_prtnum; prt++) {
|
|
if ((1 << prt) & port_mask) {
|
|
RD_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_CTRL_REG, ®);
|
|
reg |= 0x3;
|
|
WR_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_CTRL_REG, reg);
|
|
} else {
|
|
/* Disable port */
|
|
RD_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_CTRL_REG, ®);
|
|
reg &= ~0x3;
|
|
WR_PHY(name, ports_ofs + prt,
|
|
MV88E61XX_PRT_CTRL_REG, reg);
|
|
}
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Make sure SMIBusy bit cleared before another
|
|
* SMI operation can take place
|
|
*/
|
|
static int mv88e61xx_busychk(char *name)
|
|
{
|
|
u32 reg = 0;
|
|
u32 timeout = MV88E61XX_PHY_TIMEOUT;
|
|
do {
|
|
RD_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (u16 *) & reg);
|
|
if (timeout-- == 0) {
|
|
printf("SMI busy timeout\n");
|
|
return -1;
|
|
}
|
|
} while (reg & 1 << 28); /* busy mask */
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Power up the specified port and reset PHY
|
|
*/
|
|
static int mv88361xx_powerup(struct mv88e61xx_config *swconfig, u32 prt)
|
|
{
|
|
char *name = swconfig->name;
|
|
|
|
/* Write Copper Specific control reg1 (0x14) for-
|
|
* Enable Phy power up
|
|
* Energy Detect on (sense&Xmit NLP Periodically
|
|
* reset other settings default
|
|
*/
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x3360);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (0x9410 | (prt << 5)));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
/* Write PHY ctrl reg (0x0) to apply
|
|
* Phy reset (set bit 15 low)
|
|
* reset other default values
|
|
*/
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, 0x1140);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (0x9400 | (prt << 5)));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Default Setup for LED[0]_Control (ref: Table 46 Datasheet-3)
|
|
* is set to "On-1000Mb/s Link, Off Else"
|
|
* This function sets it to "On-Link, Blink-Activity, Off-NoLink"
|
|
*
|
|
* This is optional settings may be needed on some boards
|
|
* to setup PHY LEDs default configuration to detect 10/100/1000Mb/s
|
|
* Link status
|
|
*/
|
|
static int mv88361xx_led_init(struct mv88e61xx_config *swconfig, u32 prt)
|
|
{
|
|
char *name = swconfig->name;
|
|
u16 reg;
|
|
|
|
if (swconfig->led_init != MV88E61XX_LED_INIT_EN)
|
|
return 0;
|
|
|
|
/* set page address to 3 */
|
|
reg = 3;
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
|
|
1 << MV88E61XX_MODE_OFST |
|
|
1 << MV88E61XX_OP_OFST |
|
|
prt << MV88E61XX_ADDR_OFST | 22));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
/* set LED Func Ctrl reg */
|
|
reg = 1; /* LED[0] On-Link, Blink-Activity, Off-NoLink */
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
|
|
1 << MV88E61XX_MODE_OFST |
|
|
1 << MV88E61XX_OP_OFST |
|
|
prt << MV88E61XX_ADDR_OFST | 16));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
/* set page address to 0 */
|
|
reg = 0;
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
|
|
1 << MV88E61XX_MODE_OFST |
|
|
1 << MV88E61XX_OP_OFST |
|
|
prt << MV88E61XX_ADDR_OFST | 22));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Reverse Transmit polarity for Media Dependent Interface
|
|
* Pins (MDIP) bits in Copper Specific Control Register 3
|
|
* (Page 0, Reg 20 for each phy (except cpu port)
|
|
* Reference: Section 1.1 Switch datasheet-3
|
|
*
|
|
* This is optional settings may be needed on some boards
|
|
* for PHY<->magnetics h/w tuning
|
|
*/
|
|
static int mv88361xx_reverse_mdipn(struct mv88e61xx_config *swconfig, u32 prt)
|
|
{
|
|
char *name = swconfig->name;
|
|
u16 reg;
|
|
|
|
if (swconfig->mdip != MV88E61XX_MDIP_REVERSE)
|
|
return 0;
|
|
|
|
reg = 0x0f; /*Reverse MDIP/N[3:0] bits */
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR, MV88E61XX_PHY_DATA, reg);
|
|
WR_PHY(name, MV88E61XX_GLB2REG_DEVADR,
|
|
MV88E61XX_PHY_CMD, (1 << MV88E61XX_BUSY_OFST |
|
|
1 << MV88E61XX_MODE_OFST |
|
|
1 << MV88E61XX_OP_OFST |
|
|
prt << MV88E61XX_ADDR_OFST | 20));
|
|
|
|
if (mv88e61xx_busychk(name))
|
|
return -1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Marvell 88E61XX Switch initialization
|
|
*/
|
|
int mv88e61xx_switch_initialize(struct mv88e61xx_config *swconfig)
|
|
{
|
|
u32 prt;
|
|
u16 reg;
|
|
char *idstr;
|
|
char *name = swconfig->name;
|
|
|
|
if (miiphy_set_current_dev(name)) {
|
|
printf("%s failed\n", __FUNCTION__);
|
|
return -1;
|
|
}
|
|
|
|
if (!(swconfig->cpuport & ((1 << 4) | (1 << 5)))) {
|
|
swconfig->cpuport = (1 << 5);
|
|
printf("Invalid cpu port config, using default port5\n");
|
|
}
|
|
|
|
RD_PHY(name, MV88E61XX_PRT_OFST, PHY_PHYIDR2, ®);
|
|
reg &= 0xfff0;
|
|
if (reg == 0x1610)
|
|
idstr = "88E6161";
|
|
if (reg == 0x1650)
|
|
idstr = "88E6165";
|
|
if (reg == 0x1210) {
|
|
idstr = "88E6123";
|
|
/* ports 2,3,4 not available */
|
|
swconfig->ports_enabled &= 0x023;
|
|
}
|
|
|
|
/* Port based VLANs configuration */
|
|
if ((swconfig->vlancfg == MV88E61XX_VLANCFG_DEFAULT)
|
|
|| (swconfig->vlancfg == MV88E61XX_VLANCFG_ROUTER))
|
|
mv88e61xx_port_vlan_config(swconfig, MV88E61XX_MAX_PORTS_NUM,
|
|
MV88E61XX_PRT_OFST);
|
|
else {
|
|
printf("Unsupported mode %s failed\n", __FUNCTION__);
|
|
return -1;
|
|
}
|
|
|
|
if (swconfig->rgmii_delay == MV88E61XX_RGMII_DELAY_EN) {
|
|
/*
|
|
* Enable RGMII delay on Tx and Rx for CPU port
|
|
* Ref: sec 9.5 of chip datasheet-02
|
|
*/
|
|
WR_PHY(name, MV88E61XX_PRT_OFST + 5,
|
|
MV88E61XX_RGMII_TIMECTRL_REG, 0x18);
|
|
WR_PHY(name, MV88E61XX_PRT_OFST + 4,
|
|
MV88E61XX_RGMII_TIMECTRL_REG, 0xc1e7);
|
|
}
|
|
|
|
for (prt = 0; prt < MV88E61XX_MAX_PORTS_NUM; prt++) {
|
|
if (!((1 << prt) & swconfig->cpuport)) {
|
|
|
|
if (mv88361xx_led_init(swconfig, prt))
|
|
return -1;
|
|
if (mv88361xx_reverse_mdipn(swconfig, prt))
|
|
return -1;
|
|
if (mv88361xx_powerup(swconfig, prt))
|
|
return -1;
|
|
}
|
|
|
|
/*Program port state */
|
|
RD_PHY(name, MV88E61XX_PRT_OFST + prt,
|
|
MV88E61XX_PRT_CTRL_REG, ®);
|
|
WR_PHY(name, MV88E61XX_PRT_OFST + prt,
|
|
MV88E61XX_PRT_CTRL_REG,
|
|
reg | (swconfig->portstate & 0x03));
|
|
}
|
|
|
|
printf("%s Initialized on %s\n", idstr, name);
|
|
return 0;
|
|
}
|
|
|