upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
501 lines
17 KiB
501 lines
17 KiB
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x80F00000
|
|
|
|
/*****************************************************************************
|
|
*
|
|
* These settings must match the way _your_ board is set up
|
|
*
|
|
*****************************************************************************/
|
|
/* for the AY-Revision which does not use the HRCW */
|
|
#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
|
|
|
|
/* What is the oscillator's (UX2) frequency in Hz? */
|
|
#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
|
|
|
|
/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
|
|
* only the 3 least significant bits are important.
|
|
*/
|
|
#define CONFIG_SYS_SBC_S2 0x04
|
|
|
|
/* What should MODCK_H be? It is dependent on the oscillator
|
|
* frequency, MODCK[1-3], and desired CPM and core frequencies.
|
|
* Some example values (all frequencies are in MHz):
|
|
*
|
|
* MODCK_H MODCK[1-3] Osc CPM Core
|
|
* 0x2 0x2 33 133 133
|
|
* 0x2 0x4 33 133 200
|
|
* 0x5 0x5 66 133 133
|
|
* 0x5 0x7 66 133 200
|
|
*/
|
|
#define CONFIG_SYS_SBC_MODCK_H 0x06
|
|
|
|
#define CONFIG_SYS_SBC_BOOT_LOW 1 /* only for HRCW */
|
|
#undef CONFIG_SYS_SBC_BOOT_LOW
|
|
|
|
/* What should the base address of the main FLASH be and how big is
|
|
* it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE.
|
|
* The main FLASH is whichever is connected to *CS0. U-Boot expects
|
|
* this to be the SIMM.
|
|
*/
|
|
#define CONFIG_SYS_FLASH0_BASE 0x80000000
|
|
#define CONFIG_SYS_FLASH0_SIZE 16
|
|
|
|
/* What should the base address of the secondary FLASH be and how big
|
|
* is it (in Mbytes)? The secondary FLASH is whichever is connected
|
|
* to *CS6. U-Boot expects this to be the on board FLASH. If you don't
|
|
* want it enabled, don't define these constants.
|
|
*/
|
|
#define CONFIG_SYS_FLASH1_BASE 0
|
|
#define CONFIG_SYS_FLASH1_SIZE 0
|
|
#undef CONFIG_SYS_FLASH1_BASE
|
|
#undef CONFIG_SYS_FLASH1_SIZE
|
|
|
|
/* What should be the base address of SDRAM DIMM and how big is
|
|
* it (in Mbytes)?
|
|
*/
|
|
#define CONFIG_SYS_SDRAM0_BASE 0x00000000
|
|
#define CONFIG_SYS_SDRAM0_SIZE 64
|
|
|
|
/* What should be the base address of SDRAM DIMM and how big is
|
|
* it (in Mbytes)?
|
|
*/
|
|
#define CONFIG_SYS_SDRAM1_BASE 0x04000000
|
|
#define CONFIG_SYS_SDRAM1_SIZE 32
|
|
|
|
/* What should be the base address of the LEDs and switch S0?
|
|
* If you don't want them enabled, don't define this.
|
|
*/
|
|
#define CONFIG_SYS_LED_BASE 0x00000000
|
|
|
|
/*
|
|
* select serial console configuration
|
|
*
|
|
* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
|
|
* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
|
|
* for SCC).
|
|
*
|
|
* if CONFIG_CONS_NONE is defined, then the serial console routines must
|
|
* defined elsewhere.
|
|
*/
|
|
#define CONFIG_CONS_ON_SMC /* define if console on SMC */
|
|
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
|
|
#undef CONFIG_CONS_NONE /* define if console on neither */
|
|
#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
|
|
|
|
/*
|
|
* select ethernet configuration
|
|
*
|
|
* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
|
|
* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
|
|
* for FCC)
|
|
*
|
|
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
|
|
* defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
|
|
*/
|
|
#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
|
|
#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
|
|
#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
|
|
#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
|
|
|
|
#if ( CONFIG_ETHER_INDEX == 3 )
|
|
|
|
/*
|
|
* - Rx-CLK is CLK15
|
|
* - Tx-CLK is CLK16
|
|
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
|
|
* - Enable Half Duplex in FSMR
|
|
*/
|
|
# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
|
|
# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
|
|
# define CONFIG_SYS_CPMFCR_RAMTYPE 0
|
|
/*#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
|
|
# define CONFIG_SYS_FCC_PSMR 0
|
|
|
|
#else /* CONFIG_ETHER_INDEX */
|
|
# error "on RPX Super ethernet must be FCC3"
|
|
#endif /* CONFIG_ETHER_INDEX */
|
|
|
|
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
|
|
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
|
|
#define CONFIG_SYS_I2C_SLAVE 0x7F
|
|
|
|
|
|
/* Define this to reserve an entire FLASH sector (256 KB) for
|
|
* environment variables. Otherwise, the environment will be
|
|
* put in the same sector as U-Boot, and changing variables
|
|
* will erase U-Boot temporarily
|
|
*/
|
|
#define CONFIG_ENV_IN_OWN_SECT
|
|
|
|
/* Define to allow the user to overwrite serial and ethaddr */
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
/* What should the console's baud rate be? */
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
/* Ethernet MAC address */
|
|
#define CONFIG_ETHADDR 08:00:22:50:70:63
|
|
|
|
#define CONFIG_IPADDR 192.168.1.99
|
|
#define CONFIG_SERVERIP 192.168.1.3
|
|
|
|
/* Set to a positive value to delay for running BOOTCOMMAND */
|
|
#define CONFIG_BOOTDELAY -1
|
|
|
|
/* undef this to save memory */
|
|
#define CONFIG_SYS_LONGHELP
|
|
|
|
/* Monitor Command Prompt */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_IMMAP
|
|
#define CONFIG_CMD_ASKENV
|
|
#define CONFIG_CMD_I2C
|
|
#define CONFIG_CMD_REGINFO
|
|
|
|
#undef CONFIG_CMD_KGDB
|
|
|
|
|
|
/* Where do the internal registers live? */
|
|
#define CONFIG_SYS_IMMR 0xF0000000
|
|
|
|
/* Where do the on board registers (CS4) live? */
|
|
#define CONFIG_SYS_REGS_BASE 0xFA000000
|
|
|
|
/*****************************************************************************
|
|
*
|
|
* You should not have to modify any of the following settings
|
|
*
|
|
*****************************************************************************/
|
|
|
|
#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */
|
|
#define CONFIG_CPM2 1 /* Has a CPM2 */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
|
|
#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
|
|
/* Print Buffer Size */
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
|
|
|
|
#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
|
|
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
|
|
|
|
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
|
|
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
|
|
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Hard Reset Configuration Words
|
|
*/
|
|
#if defined(CONFIG_SYS_SBC_BOOT_LOW)
|
|
# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
|
|
#else
|
|
# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
|
|
#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
|
|
|
|
/* get the HRCW ISB field from CONFIG_SYS_IMMR */
|
|
#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
|
|
((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\
|
|
((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
|
|
|
|
#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11 |\
|
|
HRCW_DPPC11 |\
|
|
CONFIG_SYS_SBC_HRCW_IMMR |\
|
|
HRCW_MMR00 |\
|
|
HRCW_LBPC11 |\
|
|
HRCW_APPC10 |\
|
|
HRCW_CS10PC00 |\
|
|
(CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\
|
|
CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
|
|
|
|
/* no slaves */
|
|
#define CONFIG_SYS_HRCW_SLAVE1 0
|
|
#define CONFIG_SYS_HRCW_SLAVE2 0
|
|
#define CONFIG_SYS_HRCW_SLAVE3 0
|
|
#define CONFIG_SYS_HRCW_SLAVE4 0
|
|
#define CONFIG_SYS_HRCW_SLAVE5 0
|
|
#define CONFIG_SYS_HRCW_SLAVE6 0
|
|
#define CONFIG_SYS_HRCW_SLAVE7 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
* Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
|
|
*/
|
|
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH0_BASE + 0x00F00000)
|
|
|
|
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
|
|
# define CONFIG_SYS_RAMBOOT
|
|
#endif
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH and environment organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
|
|
|
|
#ifndef CONFIG_SYS_RAMBOOT
|
|
# define CONFIG_ENV_IS_IN_FLASH 1
|
|
|
|
# ifdef CONFIG_ENV_IN_OWN_SECT
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
|
|
# define CONFIG_ENV_SECT_SIZE 0x40000
|
|
# else
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
|
|
# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
|
|
# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
|
|
# endif /* CONFIG_ENV_IN_OWN_SECT */
|
|
#else
|
|
# define CONFIG_ENV_IS_IN_NVRAM 1
|
|
# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
|
|
# define CONFIG_ENV_SIZE 0x200
|
|
#endif /* CONFIG_SYS_RAMBOOT */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* HIDx - Hardware Implementation-dependent Registers 2-11
|
|
*-----------------------------------------------------------------------
|
|
* HID0 also contains cache control - initially enable both caches and
|
|
* invalidate contents, then the final state leaves only the instruction
|
|
* cache enabled. Note that Power-On and Hard reset invalidate the caches,
|
|
* but Soft reset does not.
|
|
*
|
|
* HID1 has only read-only information - nothing to set.
|
|
*/
|
|
#define CONFIG_SYS_HID0_INIT (/*HID0_ICE |*/\
|
|
/*HID0_DCE |*/\
|
|
HID0_ICFI |\
|
|
HID0_DCI |\
|
|
HID0_IFEM |\
|
|
HID0_ABE)
|
|
|
|
#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\
|
|
HID0_IFEM |\
|
|
HID0_ABE |\
|
|
HID0_EMCP)
|
|
#define CONFIG_SYS_HID2 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RMR - Reset Mode Register
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RMR 0
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* BCR - Bus Configuration 4-25
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_BCR (BCR_EBM |\
|
|
BCR_PLDP |\
|
|
BCR_EAV |\
|
|
BCR_NPQM0)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 4-31
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\
|
|
SIUMCR_APPC10 |\
|
|
SIUMCR_CS10PC01)
|
|
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
|
|
*/
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
|
|
SYPCR_BMT |\
|
|
SYPCR_PBME |\
|
|
SYPCR_LBME |\
|
|
SYPCR_SWRI |\
|
|
SYPCR_SWP)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TMCNTSC - Time Counter Status and Control 4-40
|
|
*-----------------------------------------------------------------------
|
|
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
|
|
* and enable Time Counter
|
|
*/
|
|
#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
|
|
TMCNTSC_ALR |\
|
|
TMCNTSC_TCF |\
|
|
TMCNTSC_TCE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 4-42
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
|
|
* Periodic timer
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS |\
|
|
PISCR_PTF |\
|
|
PISCR_PTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock Control 9-8
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RCCR - RISC Controller Configuration 13-7
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RCCR 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* Bank Bus Machine PortSz Device
|
|
* ---- --- ------- ------ ------
|
|
* 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90)
|
|
* 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
|
|
* 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
|
|
* 3 unused
|
|
* 4 60x GPCM 8 bit Board Regs, LEDs, switches
|
|
* 5 unused
|
|
* 6 unused
|
|
* 7 unused
|
|
* 8 PCMCIA
|
|
* 9 unused
|
|
* 10 unused
|
|
* 11 unused
|
|
*/
|
|
|
|
/* Bank 0 - FLASH
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_DECC_NONE |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_6_CLK |\
|
|
ORxG_EHTR)
|
|
|
|
/* Bank 1 - SDRAM
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_64 |\
|
|
BRx_MS_SDRAM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A8 |\
|
|
ORxS_NUMR_12 |\
|
|
ORxS_IBID)
|
|
|
|
#define CONFIG_SYS_PSDMR 0x014DA412
|
|
#define CONFIG_SYS_PSRT 0x79
|
|
|
|
|
|
/* Bank 2 - SDRAM
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_32 |\
|
|
BRx_MS_SDRAM_L |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
|
|
ORxS_BPD_4 |\
|
|
ORxS_ROWST_PBI0_A9 |\
|
|
ORxS_NUMR_12)
|
|
|
|
#define CONFIG_SYS_LSDMR 0x0169A512
|
|
#define CONFIG_SYS_LSRT 0x79
|
|
|
|
#define CONFIG_SYS_MPTPR (0x0800 & MPTPR_PTP_MSK)
|
|
|
|
/* Bank 4 - On board registers
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
|
|
BRx_PS_8 |\
|
|
BRx_MS_GPCM_P |\
|
|
BRx_V)
|
|
|
|
#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
|
|
ORxG_CSNT |\
|
|
ORxG_ACS_DIV1 |\
|
|
ORxG_SCY_5_CLK |\
|
|
ORxG_TRLX)
|
|
|
|
#endif /* __CONFIG_H */
|
|
|