upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
701 lines
25 KiB
701 lines
25 KiB
/*
|
|
* (C) Copyright 2000-2010
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* Pantelis Antoniou, Intracom S.A., panto@intracom.gr
|
|
* U-Boot port on NetTA4 board
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#if !defined(CONFIG_NETPHONE_VERSION) || CONFIG_NETPHONE_VERSION > 2
|
|
#error Unsupported CONFIG_NETPHONE version
|
|
#endif
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC870 1 /* This is a MPC885 CPU */
|
|
#define CONFIG_NETPHONE 1 /* ...on a NetPhone board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0x40000000
|
|
|
|
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
|
|
#undef CONFIG_8xx_CONS_SMC2
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
|
|
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
|
|
|
|
/* #define CONFIG_XIN 10000000 */
|
|
#define CONFIG_XIN 50000000
|
|
/* #define MPC8XX_HZ 120000000 */
|
|
#define MPC8XX_HZ 66666666
|
|
|
|
#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
|
|
|
|
#if 0
|
|
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
|
|
#else
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
|
|
#endif
|
|
|
|
#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */
|
|
|
|
#define CONFIG_PREBOOT "echo;"
|
|
|
|
#undef CONFIG_BOOTARGS
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"tftpboot; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
|
|
"bootm"
|
|
|
|
#define CONFIG_SOURCE
|
|
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
|
|
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
|
|
|
|
#define CONFIG_STATUS_LED 1 /* Status LED enabled */
|
|
#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
#define CONFIG_BOOTP_NISDOMAIN
|
|
|
|
#undef CONFIG_MAC_PARTITION
|
|
#undef CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
|
|
|
|
#define FEC_ENET 1 /* eth.c needs it that way... */
|
|
#undef CONFIG_SYS_DISCOVER_PHY
|
|
#define CONFIG_MII 1
|
|
#define CONFIG_MII_INIT 1
|
|
#define CONFIG_RMII 1 /* use RMII interface */
|
|
|
|
#define CONFIG_ETHER_ON_FEC1 1
|
|
#define CONFIG_FEC1_PHY 8 /* phy address of FEC */
|
|
#define CONFIG_FEC1_PHY_NORXERR 1
|
|
|
|
#define CONFIG_ETHER_ON_FEC2 1
|
|
#define CONFIG_FEC2_PHY 4
|
|
#define CONFIG_FEC2_PHY_NORXERR 1
|
|
|
|
#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#include <config_cmd_default.h>
|
|
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_PING
|
|
#define CONFIG_CMD_MII
|
|
#define CONFIG_CMD_CDP
|
|
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F 1
|
|
#define CONFIG_MISC_INIT_R
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
|
|
#define CONFIG_SYS_HUSH_PARSER 1
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xFF000000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0x40000000
|
|
#if defined(DEBUG)
|
|
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
#else
|
|
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
|
|
#endif
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
#if CONFIG_NETPHONE_VERSION == 2
|
|
#define CONFIG_SYS_FLASH_BASE4 0x40080000
|
|
#endif
|
|
|
|
#define CONFIG_SYS_RESET_ADDRESS 0x80000000
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#if CONFIG_NETPHONE_VERSION == 1
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#elif CONFIG_NETPHONE_VERSION == 2
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
|
|
#endif
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
|
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
|
|
#define CONFIG_ENV_SIZE 0x4000
|
|
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000)
|
|
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#ifndef CONFIG_CAN_DRIVER
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
|
|
#else /* we must activate GPL5 in the SIUMCR for CAN */
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
|
|
#endif /* CONFIG_CAN_DRIVER */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit
|
|
*
|
|
*/
|
|
|
|
#if CONFIG_XIN == 10000000
|
|
|
|
#if MPC8XX_HZ == 120000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 100000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 50000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 25000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 40000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 75000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#else
|
|
#error unsupported CPU freq for XIN = 10MHz
|
|
#endif
|
|
|
|
#elif CONFIG_XIN == 50000000
|
|
|
|
#if MPC8XX_HZ == 120000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 100000000
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#elif MPC8XX_HZ == 66666666
|
|
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
|
|
(1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
|
|
PLPRCR_TEXPS)
|
|
#else
|
|
#error unsupported CPU freq for XIN = 50MHz
|
|
#endif
|
|
|
|
#else
|
|
|
|
#error unsupported XIN freq
|
|
#endif
|
|
|
|
|
|
/*
|
|
*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*
|
|
* Note: When TBS == 0 the timebase is independent of current cpu clock.
|
|
*/
|
|
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#if MPC8XX_HZ > 66666666
|
|
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00 | SCCR_EBDF01)
|
|
#else
|
|
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
/*#define CONFIG_SYS_DER 0x2002000F*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
|
|
|
|
/* used to re-map FLASH both when starting from SRAM or FLASH:
|
|
* restrict access enough to keep SRAM working (if any)
|
|
* but not too much to meddle with FLASH accesses
|
|
*/
|
|
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
|
|
|
|
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
|
|
|
|
#if CONFIG_NETPHONE_VERSION == 2
|
|
|
|
#define FLASH_BASE4_PRELIM 0x40080000 /* FLASH bank #1 */
|
|
|
|
#define CONFIG_SYS_OR4_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_OR4_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_BR4_PRELIM ((FLASH_BASE4_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
|
|
|
|
#endif
|
|
|
|
/*
|
|
* BR3 and OR3 (SDRAM)
|
|
*
|
|
*/
|
|
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */
|
|
#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */
|
|
|
|
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS)
|
|
|
|
#define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
|
|
#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*/
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*
|
|
* The Divider for PTA (refresh timer) configuration is based on an
|
|
* example SDRAM configuration (64 MBit, one bank). The adjustment to
|
|
* the number of chip selects (NCS) and the actually needed refresh
|
|
* rate is done by setting MPTPR.
|
|
*
|
|
* PTA is calculated from
|
|
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
|
|
*
|
|
* gclk CPU clock (not bus clock!)
|
|
* Trefresh Refresh cycle * 4 (four word bursts used)
|
|
*
|
|
* 4096 Rows from SDRAM example configuration
|
|
* 1000 factor s -> ms
|
|
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
|
|
* 4 Number of refresh cycles per period
|
|
* 64 Refresh cycle in ms per number of rows
|
|
* --------------------------------------------
|
|
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
|
|
*
|
|
* 50 MHz => 50.000.000 / Divider = 98
|
|
* 66 Mhz => 66.000.000 / Divider = 129
|
|
* 80 Mhz => 80.000.000 / Divider = 156
|
|
*/
|
|
|
|
#define CONFIG_SYS_MAMR_PTA 234
|
|
|
|
/*
|
|
* For 16 MBit, refresh rates could be 31.3 us
|
|
* (= 64 ms / 2K = 125 / quad bursts).
|
|
* For a simpler initialization, 15.6 us is used instead.
|
|
*
|
|
* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
|
|
* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
|
|
*/
|
|
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
|
|
|
|
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
|
|
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 8 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
/* 9 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */
|
|
|
|
/****************************************************************/
|
|
|
|
#define DSP_SIZE 0x00010000 /* 64K */
|
|
#define NAND_SIZE 0x00010000 /* 64K */
|
|
|
|
#define DSP_BASE 0xF1000000
|
|
#define NAND_BASE 0xF1010000
|
|
|
|
/*****************************************************************************/
|
|
|
|
#define CONFIG_SYS_DIRECT_FLASH_TFTP
|
|
|
|
/*****************************************************************************/
|
|
|
|
#if CONFIG_NETPHONE_VERSION == 1
|
|
#define STATUS_LED_BIT 0x00000008 /* bit 28 */
|
|
#elif CONFIG_NETPHONE_VERSION == 2
|
|
#define STATUS_LED_BIT 0x00000080 /* bit 24 */
|
|
#endif
|
|
|
|
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
|
|
#define STATUS_LED_STATE STATUS_LED_BLINKING
|
|
|
|
#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
|
|
#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/* LEDs */
|
|
|
|
/* led_id_t is unsigned int mask */
|
|
typedef unsigned int led_id_t;
|
|
|
|
#define __led_toggle(_msk) \
|
|
do { \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat ^= (_msk); \
|
|
} while(0)
|
|
|
|
#define __led_set(_msk, _st) \
|
|
do { \
|
|
if ((_st)) \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat |= (_msk); \
|
|
else \
|
|
((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pedat &= ~(_msk); \
|
|
} while(0)
|
|
|
|
#define __led_init(msk, st) __led_set(msk, st)
|
|
|
|
#endif
|
|
|
|
/***********************************************************************************************************
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
(V1) version 1 of the board
|
|
(V2) version 2 of the board
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Pin definitions:
|
|
|
|
+------+----------------+--------+------------------------------------------------------------
|
|
| # | Name | Type | Comment
|
|
+------+----------------+--------+------------------------------------------------------------
|
|
| PA3 | SPIEN_MAX | Output | MAX serial to uart chip select
|
|
| PA7 | DSP_INT | Output | DSP interrupt
|
|
| PA10 | DSP_RESET | Output | DSP reset
|
|
| PA14 | USBOE | Output | USB (1)
|
|
| PA15 | USBRXD | Output | USB (1)
|
|
| PB19 | BT_RTS | Output | Bluetooth (0)
|
|
| PB23 | BT_CTS | Output | Bluetooth (0)
|
|
| PB26 | SPIEN_SEP | Output | Serial EEPROM chip select
|
|
| PB27 | SPICS_DISP | Output | Display chip select
|
|
| PB28 | SPI_RXD_3V | Input | SPI Data Rx
|
|
| PB29 | SPI_TXD | Output | SPI Data Tx
|
|
| PB30 | SPI_CLK | Output | SPI Clock
|
|
| PC10 | DISPA0 | Output | Display A0
|
|
| PC11 | BACKLIGHT | Output | Display backlit
|
|
| PC12 | SPI2RXD | Input | (V1) 2nd SPI RXD
|
|
| | IO_RESET | Output | (V2) General I/O reset
|
|
| PC13 | SPI2TXD | Output | (V1) 2nd SPI TXD (V1)
|
|
| | HOOK | Input | (V2) Hook input interrupt
|
|
| PC15 | SPI2CLK | Output | (V1) 2nd SPI CLK
|
|
| | F_RY_BY | Input | (V2) NAND F_RY_BY
|
|
| PE17 | F_ALE | Output | NAND F_ALE
|
|
| PE18 | F_CLE | Output | NAND F_CLE
|
|
| PE20 | F_CE | Output | NAND F_CE
|
|
| PE24 | SPICS_SCOUT | Output | (V1) Codec chip select
|
|
| | LED | Output | (V2) LED
|
|
| PE27 | SPICS_ER | Output | External serial register CS
|
|
| PE28 | LEDIO1 | Output | (V1) LED
|
|
| | BKBR1 | Input | (V2) Keyboard input scan
|
|
| PE29 | LEDIO2 | Output | (V1) LED hook for A (TA2)
|
|
| | BKBR2 | Input | (V2) Keyboard input scan
|
|
| PE30 | LEDIO3 | Output | (V1) LED hook for A (TA2)
|
|
| | BKBR3 | Input | (V2) Keyboard input scan
|
|
| PE31 | F_RY_BY | Input | (V1) NAND F_RY_BY
|
|
| | BKBR4 | Input | (V2) Keyboard input scan
|
|
+------+----------------+--------+---------------------------------------------------
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Serial register input:
|
|
|
|
+------+----------------+------------------------------------------------------------
|
|
| # | Name | Comment
|
|
+------+----------------+------------------------------------------------------------
|
|
| 0 | BKBR1 | (V1) Keyboard input scan
|
|
| 1 | BKBR3 | (V1) Keyboard input scan
|
|
| 2 | BKBR4 | (V1) Keyboard input scan
|
|
| 3 | BKBR2 | (V1) Keyboard input scan
|
|
| 4 | HOOK | (V1) Hook switch
|
|
| 5 | BT_LINK | (V1) Bluetooth link status
|
|
| 6 | HOST_WAKE | (V1) Bluetooth host wake up
|
|
| 7 | OK_ETH | (V1) Cisco inline power OK status
|
|
+------+----------------+------------------------------------------------------------
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Serial register output:
|
|
|
|
+------+----------------+------------------------------------------------------------
|
|
| # | Name | Comment
|
|
+------+----------------+------------------------------------------------------------
|
|
| 0 | KEY1 | Keyboard output scan
|
|
| 1 | KEY2 | Keyboard output scan
|
|
| 2 | KEY3 | Keyboard output scan
|
|
| 3 | KEY4 | Keyboard output scan
|
|
| 4 | KEY5 | Keyboard output scan
|
|
| 5 | KEY6 | Keyboard output scan
|
|
| 6 | KEY7 | Keyboard output scan
|
|
| 7 | BT_WAKE | Bluetooth wake up
|
|
+------+----------------+------------------------------------------------------------
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Chip selects:
|
|
|
|
+------+----------------+------------------------------------------------------------
|
|
| # | Name | Comment
|
|
+------+----------------+------------------------------------------------------------
|
|
| CS0 | CS0 | Boot flash
|
|
| CS1 | CS_FLASH | NAND flash
|
|
| CS2 | CS_DSP | DSP
|
|
| CS3 | DCS_DRAM | DRAM
|
|
| CS4 | CS_FLASH2 | (V2) 2nd flash
|
|
+------+----------------+------------------------------------------------------------
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Interrupts:
|
|
|
|
+------+----------------+------------------------------------------------------------
|
|
| # | Name | Comment
|
|
+------+----------------+------------------------------------------------------------
|
|
| IRQ1 | IRQ_DSP | DSP interrupt
|
|
| IRQ3 | S_INTER | DUSLIC ???
|
|
| IRQ4 | F_RY_BY | NAND
|
|
| IRQ7 | IRQ_MAX | MAX 3100 interrupt
|
|
+------+----------------+------------------------------------------------------------
|
|
|
|
----------------------------------------------------------------------------------------------
|
|
|
|
Interrupts on PCMCIA pins:
|
|
|
|
+------+----------------+------------------------------------------------------------
|
|
| # | Name | Comment
|
|
+------+----------------+------------------------------------------------------------
|
|
| IP_A0| PHY1_LINK | Link status changed for #1 Ethernet interface
|
|
| IP_A1| PHY2_LINK | Link status changed for #2 Ethernet interface
|
|
| IP_A2| RMII1_MDINT | PHY interrupt for #1
|
|
| IP_A3| RMII2_MDINT | PHY interrupt for #2
|
|
| IP_A5| HOST_WAKE | (V2) Bluetooth host wake
|
|
| IP_A6| OK_ETH | (V2) Cisco inline power OK
|
|
+------+----------------+------------------------------------------------------------
|
|
|
|
*************************************************************************************************/
|
|
|
|
#define CONFIG_SED156X 1 /* use SED156X */
|
|
#define CONFIG_SED156X_PG12864Q 1 /* type of display used */
|
|
|
|
/* serial interfacing macros */
|
|
|
|
#define SED156X_SPI_RXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
|
|
#define SED156X_SPI_RXD_MASK 0x00000008
|
|
|
|
#define SED156X_SPI_TXD_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
|
|
#define SED156X_SPI_TXD_MASK 0x00000004
|
|
|
|
#define SED156X_SPI_CLK_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
|
|
#define SED156X_SPI_CLK_MASK 0x00000002
|
|
|
|
#define SED156X_CS_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat)
|
|
#define SED156X_CS_MASK 0x00000010
|
|
|
|
#define SED156X_A0_PORT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat)
|
|
#define SED156X_A0_MASK 0x0020
|
|
|
|
/*************************************************************************************************/
|
|
|
|
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
|
|
#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE 1
|
|
#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE 1
|
|
|
|
/*************************************************************************************************/
|
|
|
|
/* use board specific hardware */
|
|
#undef CONFIG_WATCHDOG /* watchdog disabled */
|
|
#define CONFIG_HW_WATCHDOG
|
|
#define CONFIG_SHOW_ACTIVITY
|
|
|
|
/*************************************************************************************************/
|
|
|
|
/* phone console configuration */
|
|
|
|
#define PHONE_CONSOLE_POLL_HZ (CONFIG_SYS_HZ/200) /* poll every 5ms */
|
|
|
|
/*************************************************************************************************/
|
|
|
|
#define CONFIG_CDP_DEVICE_ID 20
|
|
#define CONFIG_CDP_DEVICE_ID_PREFIX "NP" /* netphone */
|
|
#define CONFIG_CDP_PORT_ID "eth%d"
|
|
#define CONFIG_CDP_CAPABILITIES 0x00000010
|
|
#define CONFIG_CDP_VERSION "u-boot" " " U_BOOT_DATE " " U_BOOT_TIME
|
|
#define CONFIG_CDP_PLATFORM "Intracom NetPhone"
|
|
#define CONFIG_CDP_TRIGGER 0x20020001
|
|
#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */
|
|
#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone */
|
|
|
|
/*************************************************************************************************/
|
|
|
|
#define CONFIG_AUTO_COMPLETE 1
|
|
|
|
/*************************************************************************************************/
|
|
|
|
#define CONFIG_CRC32_VERIFY 1
|
|
|
|
/*************************************************************************************************/
|
|
|
|
#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE 1
|
|
|
|
/*************************************************************************************************/
|
|
#endif /* __CONFIG_H */
|
|
|