upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
283 lines
7.4 KiB
283 lines
7.4 KiB
/*
|
|
* Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/errno.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/imx-common/iomux-v3.h>
|
|
#include <mmc.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <usb.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
|
|
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
|
|
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
|
|
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
|
|
|
|
int dram_init(void)
|
|
{
|
|
#if defined(CONFIG_MX6DL) && !defined(CONFIG_MX6DL_LPDDR2) && \
|
|
defined(CONFIG_DDR_32BIT)
|
|
gd->ram_size = ((phys_size_t)CONFIG_DDR_MB * 1024 * 1024) / 2;
|
|
#else
|
|
gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
iomux_v3_cfg_t const uart4_pads[] = {
|
|
MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
iomux_v3_cfg_t const usdhc3_pads[] = {
|
|
MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
|
|
};
|
|
|
|
iomux_v3_cfg_t const usdhc4_pads[] = {
|
|
MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
};
|
|
|
|
iomux_v3_cfg_t const enet_pads[] = {
|
|
MX6_PAD_KEY_COL1__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_KEY_COL2__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
};
|
|
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
|
|
}
|
|
|
|
static void setup_iomux_enet(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
|
|
}
|
|
|
|
#ifdef CONFIG_FSL_ESDHC
|
|
struct fsl_esdhc_cfg usdhc_cfg[2] = {
|
|
{USDHC3_BASE_ADDR},
|
|
{USDHC4_BASE_ADDR},
|
|
};
|
|
|
|
int board_mmc_getcd(struct mmc *mmc)
|
|
{
|
|
struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
|
|
int ret;
|
|
|
|
if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
|
|
gpio_direction_input(IMX_GPIO_NR(6, 11));
|
|
ret = !gpio_get_value(IMX_GPIO_NR(6, 11));
|
|
} else /* Don't have the CD GPIO pin on board */
|
|
ret = 1;
|
|
|
|
return ret;
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
int ret;
|
|
u32 index = 0;
|
|
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
|
|
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
|
|
|
|
for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
|
|
switch (index) {
|
|
case 0:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
|
|
break;
|
|
case 1:
|
|
imx_iomux_v3_setup_multiple_pads(
|
|
usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
|
|
break;
|
|
default:
|
|
printf("Warning: you configured more USDHC controllers"
|
|
"(%d) then supported by the board (%d)\n",
|
|
index + 1, CONFIG_SYS_FSL_USDHC_NUM);
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#define MII_MMD_ACCESS_CTRL_REG 0xd
|
|
#define MII_MMD_ACCESS_ADDR_DATA_REG 0xe
|
|
#define MII_DBG_PORT_REG 0x1d
|
|
#define MII_DBG_PORT2_REG 0x1e
|
|
|
|
int fecmxc_mii_postcall(int phy)
|
|
{
|
|
unsigned short val;
|
|
|
|
/*
|
|
* Due to the i.MX6Q Armadillo2 board HW design,there is
|
|
* no 125Mhz clock input from SOC. In order to use RGMII,
|
|
* We need enable AR8031 ouput a 125MHz clk from CLK_25M
|
|
*/
|
|
miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x7);
|
|
miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, 0x8016);
|
|
miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x4007);
|
|
miiphy_read("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, &val);
|
|
val &= 0xffe3;
|
|
val |= 0x18;
|
|
miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, val);
|
|
|
|
/* For the RGMII phy, we need enable tx clock delay */
|
|
miiphy_write("FEC", phy, MII_DBG_PORT_REG, 0x5);
|
|
miiphy_read("FEC", phy, MII_DBG_PORT2_REG, &val);
|
|
val |= 0x0100;
|
|
miiphy_write("FEC", phy, MII_DBG_PORT2_REG, val);
|
|
|
|
miiphy_write("FEC", phy, MII_BMCR, 0xa100);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct eth_device *dev;
|
|
int ret = cpu_eth_init(bis);
|
|
|
|
if (ret)
|
|
return ret;
|
|
|
|
dev = eth_get_dev_by_name("FEC");
|
|
if (!dev) {
|
|
printf("FEC MXC: Unable to get FEC device entry\n");
|
|
return -EINVAL;
|
|
}
|
|
|
|
ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
|
|
if (ret) {
|
|
printf("FEC MXC: Unable to register FEC mii postcall\n");
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
#define USB_OTHERREGS_OFFSET 0x800
|
|
#define UCTRL_PWR_POL (1 << 9)
|
|
|
|
static iomux_v3_cfg_t const usb_otg_pads[] = {
|
|
MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_usb(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
|
|
ARRAY_SIZE(usb_otg_pads));
|
|
|
|
/*
|
|
* set daisy chain for otg_pin_id on 6q.
|
|
* for 6dl, this bit is reserved
|
|
*/
|
|
imx_iomux_set_gpr_register(1, 13, 1, 1);
|
|
}
|
|
|
|
int board_ehci_hcd_init(int port)
|
|
{
|
|
u32 *usbnc_usb_ctrl;
|
|
|
|
if (port > 0)
|
|
return -EINVAL;
|
|
|
|
usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
|
|
port * 4);
|
|
|
|
setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
setup_iomux_enet();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#ifdef CONFIG_USB_EHCI_MX6
|
|
setup_usb();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
#ifdef CONFIG_MX6DL
|
|
puts("Board: MX6DL-Armadillo2\n");
|
|
#else
|
|
puts("Board: MX6Q-Armadillo2\n");
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|