upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
88 lines
2.8 KiB
88 lines
2.8 KiB
/*
|
|
* (C) Copyright 2007
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <asm-offsets.h>
|
|
#include <ppc_asm.tmpl>
|
|
#include <config.h>
|
|
#include <asm/mmu.h>
|
|
|
|
/**************************************************************************
|
|
* TLB TABLE
|
|
*
|
|
* This table is used by the cpu boot code to setup the initial tlb
|
|
* entries. Rather than make broad assumptions in the cpu source tree,
|
|
* this table lets each board set things up however they like.
|
|
*
|
|
* Pointer to the table is returned in r1
|
|
*
|
|
*************************************************************************/
|
|
.section .bootpg,"ax"
|
|
.globl tlbtab
|
|
|
|
tlbtab:
|
|
tlbtab_start
|
|
|
|
/*
|
|
* BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
|
|
* speed up boot process. It is patched after relocation to enable SA_I
|
|
*/
|
|
#ifndef CONFIG_NAND_SPL
|
|
tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 0, AC_RWX | SA_G)
|
|
#else
|
|
tlbentry(CONFIG_SYS_NAND_BOOT_SPL_SRC, SZ_4K, CONFIG_SYS_NAND_BOOT_SPL_SRC, 0, AC_RWX | SA_G)
|
|
tlbentry(CONFIG_SYS_SDRAM_BASE, SZ_256M, CONFIG_SYS_SDRAM_BASE, 0, AC_RWX | SA_IG)
|
|
#endif
|
|
|
|
/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
|
|
tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
|
|
|
|
/* PCI base & peripherals */
|
|
tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, CONFIG_SYS_PCI_BASE, 0, AC_RW | SA_IG)
|
|
|
|
tlbentry(CONFIG_SYS_NVRAM_BASE_ADDR, SZ_256M, CONFIG_SYS_NVRAM_BASE_ADDR, 0, AC_RWX | SA_W|SA_I)
|
|
tlbentry(CONFIG_SYS_NAND_ADDR, SZ_4K, CONFIG_SYS_NAND_ADDR, 0, AC_RWX | SA_W|SA_I)
|
|
|
|
/* PCI */
|
|
tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 0, AC_RW | SA_IG)
|
|
tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 0, AC_RW | SA_IG)
|
|
tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 0, AC_RW | SA_IG)
|
|
tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 0, AC_RW | SA_IG)
|
|
|
|
/* USB 2.0 Device */
|
|
tlbentry(CONFIG_SYS_USB_DEVICE, SZ_1K, CONFIG_SYS_USB_DEVICE, 0, AC_RW | SA_IG)
|
|
|
|
tlbtab_end
|
|
|
|
#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
|
|
/*
|
|
* For NAND booting the first TLB has to be reconfigured to full size
|
|
* and with caching disabled after running from RAM!
|
|
*/
|
|
#define TLB00 TLB0(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M)
|
|
#define TLB01 TLB1(CONFIG_SYS_BOOT_BASE_ADDR, 0)
|
|
#define TLB02 TLB2(AC_RWX | SA_IG)
|
|
|
|
.globl reconfig_tlb0
|
|
reconfig_tlb0:
|
|
sync
|
|
isync
|
|
addi r4,r0,0x0000 /* TLB entry #0 */
|
|
lis r5,TLB00@h
|
|
ori r5,r5,TLB00@l
|
|
tlbwe r5,r4,0x0000 /* Save it out */
|
|
lis r5,TLB01@h
|
|
ori r5,r5,TLB01@l
|
|
tlbwe r5,r4,0x0001 /* Save it out */
|
|
lis r5,TLB02@h
|
|
ori r5,r5,TLB02@l
|
|
tlbwe r5,r4,0x0002 /* Save it out */
|
|
sync
|
|
isync
|
|
blr
|
|
#endif
|
|
|