upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/board/freescale/c29xpcie
Jaiprakash Singh 39b0bbbb23 driver/ifc: Add 64KB page support 10 years ago
..
Kconfig kconfig: remove redundant "string" type in arch and board Kconfigs 10 years ago
MAINTAINERS powerpc/c29xpcie: Add secure boot support 10 years ago
Makefile powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 11 years ago
README powerpc/mpc85xx:Increase binary size for P, B & T series boards. 11 years ago
c29xpcie.c driver/ifc: Add 64KB page support 10 years ago
cpld.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 11 years ago
cpld.h
ddr.c powerpc/c29xpcie: Getting DDR SPD image from 16-bit sub-address EEPROM 11 years ago
law.c boards/c29xpcie: Update TLB and LAW size for IFC NAND, CPLD 11 years ago
spl.c common: Add get_effective_memsize() to memsize.c 11 years ago
spl_minimal.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 11 years ago
tlb.c powerpc/c29xpcie: 8k page size NAND boot support base on TPL/SPL 11 years ago

README

Overview
=========
C29XPCIE board is a series of Freescale PCIe add-in cards to perform
as public key crypto accelerator or secure key management module.
It includes C293PCIE board, C293PCIE board and C291PCIE board.
The Freescale C29x family is a high performance crypto co-processor.
It combines a single e500v2 core with necessary SEC engines.
(maximum core frequency 1000/1200 MHz).

The C29xPCIE board features are as follows:
Memory subsystem:
- 512Mbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
- 64 Mbyte NOR flash single-chip memory
- 4 Gbyte NAND flash memory
- 1 Mbit AT24C1024 I2C EEPROM
- 16 Mbyte SPI memory

Interfaces:
- 10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port
- eTSEC2, RGMII: one 10/100/1000 port
- DUART interface:
- DUART interface: supports two UARTs up to 115200 bps for
console display

Board connectors:
- Mini-ITX power supply connector
- JTAG/COP for debugging

Physical Memory Map on C29xPCIE
===============================
Address Start Address End Memory type
0x0_0000_0000 - 0x0_1fff_ffff 512MB DDR
0xc_0000_0000 - 0xc_8fff_ffff 256MB PCIE memory
0xf_ec00_0000 - 0xf_efff_ffff 64MB NOR flash
0xf_ffb0_0000 - 0xf_ffb7_ffff 512KB SRAM
0xf_ffc0_0000 - 0xf_ffc0_ffff 64KB PCIE IO
0xf_ffdf_0000 - 0xf_ffdf_0fff 4KB CPLD
0xf_ffe0_0000 - 0xf_ffef_ffff 1MB CCSR

Serial Port Configuration on C29xPCIE
=====================================
Configure the serial port of the attached computer with the following values:
-Data rate: 115200 bps
-Number of data bits: 8
-Parity: None
-Number of Stop bits: 1
-Flow Control: Hardware/None

Settings of DIP-switch
======================
SW5[1:4]= 1111 and SW5[6]=0 for boot from 16bit NOR flash
SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash
Note: 1 stands for 'off', 0 stands for 'on'

Build and program u-boot to NOR flash
==================================
1. Build u-boot.bin image example:
export ARCH=powerpc
export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
make C293PCIE

2. Program u-boot.bin into NOR flash
=> tftp $loadaddr $uboot
=> protect off eff40000 +$filesize
=> erase eff40000 +$filesize
=> cp.b $loadaddr eff40000 $filesize

3. Check SW5[1:4]= 1111 and SW5[6]=0, then power on.

Alternate NOR bank
==================
There are four banks in C29XPCIE board, example to change bank booting:
1. Program u-boot.bin into alternate NOR bank
=> tftp $loadaddr $uboot
=> protect off e9f40000 +$filesize
=> erase e9f40000 +$filesize
=> cp.b $loadaddr e9f40000 $filesize

2. Switch to alternate NOR bank
=> cpld_cmd reset altbank [bank]
- [bank] bank value select 1-4
- bank 1 on the flash 0x0000000~0x0ffffff
- bank 2 on the flash 0x1000000~0x1ffffff
- bank 3 on the flash 0x2000000~0x2ffffff
- bank 4 on the flash 0x3000000~0x3ffffff
or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again.

Build and program u-boot to SPI flash
==================================
1. Build u-boot-spi.bin image
make C29xPCIE_SPIFLASH_config; make
Need the boot_format tool to generate u-boot-spi.bin from the u-boot.bin.

2. Program u-boot-spi.bin into SPI flash
=> tftp $loadaddr $uboot-spi
=> sf erase 0 100000
=> sf write $loadaddr 0 $filesize

3. Check SW5[1:4]= 0110 and SW5[6]=0, then power on.