upstream u-boot with additional patches for our devices/boards: https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ; Gbit ethernet patch for some LIME2 revisions ; with SPI flash support
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 
 
u-boot/CHANGELOG

13132 lines
426 KiB

commit ff285ca07eda1ea4a8909848cc1cc604ec8fec9c
Author: Vlad Lungu <vlad@comsys.ro>
Date: Thu Oct 4 20:47:10 2007 +0300
Fix NE2000 driver:
Fixed typo in ne2000.h, thinko re n2k_inb() usage, don't try
to do anything in eth_stop() if eth_init() was not called.
Simplified RX path in order to avoid timeouts on really really
fast NE2000 cards (read: qemu with internal tftp), NetLoop() is
clever enough to cope with 1 packet per eth_rx().
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
commit 5441f61a3d8b7034f19fc1361183e936198e6dbb
Author: Detlev Zundel <dzu@denx.de>
Date: Fri Oct 19 16:47:26 2007 +0200
Fix two typos.
Signed-off-by: Detlev Zundel <dzu@denx.de>
commit 281df457c1aa50d2752165d0c5c3282d4027b974
Author: Tony Li <tony.li@freescale.com>
Date: Thu Oct 18 17:47:19 2007 +0800
mpc83xx: Add configure entry for MPC83xx ATM support
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit d2646554f529a9577515eceb0ec5eceee18244ba
Author: Tony Li <tony.li@freescale.com>
Date: Thu Oct 18 17:44:38 2007 +0800
mpc83xx: pq-mds-pib.c typo error
Correct to val8 from val.
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 3e11ae80fec1ee12194940955431186abf6009c2
Author: Stefan Roese <sr@denx.de>
Date: Wed Oct 17 15:40:19 2007 +0200
ppc4xx: Add 667/133 (CPU/PLB) frequency setup to Sequoia bootstrap command
Signed-off-by: Stefan Roese <sr@denx.de>
commit 7ee6ba1a056e4061ab4cfde30127e332e7957afd
Author: runet@innovsys.com <runet@innovsys.com>
Date: Tue Oct 16 14:50:40 2007 -0500
Make MPC8266ADS board compile again.
Signed-off-by: Runet Torgersen <runet@innovsys.com>
commit 2491167c245d8ebe6f2dbd8c4287aaa0d14fe93a
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Aug 27 12:41:03 2007 -0500
86xx: Allow for fewer DDR slots per memory controller.
As a direct correlation exists between DDR DIMM slots
and SPD EEPROM addresses used to configure them, use
the individually defined SPD_EEPROM_ADDRESS* values to
determine if a DDR DIMM slot should have its SPD
configuration read or not.
Effectively, this now allows for 1 or 2 DIMM slots
per memory controller.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4d4a945e189a2f384c66432316da2788a0ac1607
Author: Rodolfo Giometti <giometti@enneenne.com>
Date: Mon Oct 15 11:59:17 2007 +0200
PXA USB OHCI: "usb stop" implementation.
Some USB keys need to be switched off before loading the kernel
otherwise they can remain in an undefined status which prevents them
to be correctly recognized by the kernel.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
commit e2e93442e558cf1500e92861f99713b2f045ea22
Author: Stefan Roese <sr@denx.de>
Date: Mon Oct 15 11:39:00 2007 +0200
ppc4xx: Fix bug in I2C bootstrap values for Sequoia/Rainier
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.
This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.
Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:
AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz
33MHz async PCI frequency:
PLB = 133:
=> 32 <= 44.3 <= 65 (div = 3)
PLB = 166:
=> 32 <= 55.3 <= 65 (div = 3)
66MHz async PCI frequency:
PLB = 133:
=> 65 <= 66.5 <= 132 (div = 2)
PLB = 166:
=> 65 <= 83 <= 132 (div = 2)
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5a5958b7de70ae99f0e7cbd5c97ec1346e051587
Author: Stefan Roese <sr@denx.de>
Date: Mon Oct 15 11:29:33 2007 +0200
ppc4xx: Fix incorrect 33/66MHz PCI clock log-message on Sequoia & Yosemite
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
commit da3aad55cbde80ab6e301aafa82a2c411aa53eff
Author: Martin Krause <martin.krause@tqs.de>
Date: Wed Sep 26 17:55:56 2007 +0200
TQM860M: adjust for doubled flash sector size.
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit 9d29250e2e62f4bf20c7a20b4173d84c48f11f5d
Author: Jens Gehrlein <jens.gehrlein@tqs.de>
Date: Wed Sep 26 17:55:54 2007 +0200
TQM8xx: Fix CAN timing.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit d43e489baf02afae49077791fb22332d240d8656
Author: Martin Krause <martin.krause@tqs.de>
Date: Thu Sep 27 14:54:36 2007 +0200
TQM866M: fix SDRAM refresh
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 97. This result
in a refresh rate of 4 * 7.8 us at the default clock
50 MHz. At 133 MHz the value will be then 4 * 2.9 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit 9ef57bbee1c67cc01da2026c242c4692db32be36
Author: Martin Krause <martin.krause@tqs.de>
Date: Wed Sep 26 17:55:55 2007 +0200
TQM866M: adjust for doubled flash sector size.
Adjust flash map to support the new S29GLxxN (N-Type) Flashes with
doubled sector size.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit f8bf90461d9bad2e6fed31fcebaf235f60dd6763
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Oct 14 16:12:29 2007 +0200
[FIX] XUPV2P change command handling
and remove code violation
commit 636400198228d96983c06657b17f760f5989958e
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Oct 14 00:13:19 2007 +0200
Prepare for 1.3.0-rc3 release
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 68f14f77ca5fe5f9cc025c8cae101671f628309f
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Sat Sep 29 13:41:37 2007 +0200
Fix warning differ in signedness in cpu/pxa/mmc.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
commit fc19e36f741e8bc727c0a330170b3b5db90399ef
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Oct 13 23:51:14 2007 +0200
Fix warning differ in signedness in board/mpl/vcma9/vcma9.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit de74b9eeacccaf0a42e5ecc9ae79a88f7a311296
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Oct 13 21:15:39 2007 +0200
Coding Style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit e1893815b0999410d7a327589611c7b38e95299e
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Oct 12 15:49:39 2007 +0200
GP3 SSA: enable RTC
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 8002012041f1ff9f997a5727abe5015f70cd2e46
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Tue Oct 9 13:58:24 2007 +0200
[ads5121] EEPROM support added.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 7b624ad254b97e5a25dca2304a398b64aeedaffe
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sat Oct 6 18:55:35 2007 +0200
AVR32: Initialize bi_flash* in board_init_r
The ATSTK1000-specific flash driver intializes bi_flashstart,
bi_flashsize and bi_flashoffset, but other flash drivers, like the CFI
driver, don't.
Initialize these in board_init_r instead so that things will still be
set up correctly when we switch to the CFI driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 2b2a587d6d3076387d22ac740f44044bf46e2cb8
Author: Marian Balakowicz <m8@semihalf.com>
Date: Fri Oct 5 10:40:54 2007 +0200
tqm5200: Fix CONFIG_CMD_PCI typo in board config file.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
commit 92869195ef8210758d2176230c0a36897afd50ed
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Fri Oct 5 09:46:06 2007 +0200
CM5200: Fix missing null-termination in hostname manipulation code
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit 9add9884b1fddc34ca186e00a2f868ccd5d02d87
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Tue Oct 2 19:09:01 2007 +0200
Fix memtest breakage
CFG_MEMTEST_START uses weird magic involving gd, which fails to
compile. Use hardcoded values instead (we actually know how much RAM
we have on board.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 738815c0cc44aa329097f868dc1efc49ede9c5ba
Author: Stefan Roese <sr@denx.de>
Date: Tue Oct 2 11:44:46 2007 +0200
ppc4xx: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 87c1833a39e944db66385286fd5e28f9b3fcdd50
Author: Stefan Roese <sr@denx.de>
Date: Tue Oct 2 11:44:19 2007 +0200
ppc4xx: lwmon5: Remove watchdog for now, since not fully tested yet
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2db64784061bfc34f4ba70ef1d2fbe7133b55670
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Mon Oct 1 09:51:50 2007 +0200
Program EPLD to force full duplex mode for PHY.
EPLD forces modes of PHY operation. By default full duplex is turned off.
This fix turns it on.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 785c13477b77dcd2e6c5128fffcdb4e1943f4818
Author: Timo Ketola <timo.ketola@exertus.fi>
Date: Mon Sep 24 14:50:32 2007 +0300
Bugfix: Use only one PTD for one endpoint
Original isp116x-hcd code prepared multiple PTDs for longer than 16
byte transfers for one endpoint. That is unnecessary because the
ISP116x is able to split long data from one PTD into multiple
transactions based on the buffer size of the endpoint. It also caused
serious problems if the endpoint NAKed some of the transactions. In
that case ISP116x wouldn't notice that the other PTDs were for the same
endpoint and would try the other PTDs possibly out of order. That would
break the whole transfer.
This patch makes isp116x_submit_job to use one PTD for one transfer.
Signed-off-by: Timo Ketola <timo.ketola@exertus.fi>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
commit 86ec86c04326c3913178a7679aa910de071da75d
Author: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Date: Thu Sep 27 23:27:47 2007 +0200
Fix missing DECLARE_GLOBAL_DATA_PTR on CONFIG_LPC2292 in serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
commit 3e954beb614b5b190d7f4f4c3b641437a0132e35
Author: Stefan Roese <sr@denx.de>
Date: Tue Sep 11 14:12:55 2007 +0200
ppc4xx: lwmon5: Change GPIO 58 to default to low (watchdog test)
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0d38effc6e359e6b1b0c78d66e8bc1a4dc15a2ae
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Sep 25 15:48:05 2007 -0600
Fpga: fix incorrect test of CFG_FPGA_XILINX macro
CFG_FPGA_XILINX is a bit value used to test against the value in
CONFIG_FPGA. Testing for a value will always return TRUE. I don't
think that is the intention in this code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 853643d8cf2ca80cb2e25c53ad5dc580abafe166
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:41:30 2007 +0200
[FIX] change command handling and removing code violation
commit f240356507038e5ce55e8a24cb2607e9eae6d10c
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:36:06 2007 +0200
[FIX] change sets of commands
because changing of command handling brings
compilation problems
commit cb1bc63b75a232571eb69aa2c8aa919321655845
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:30:42 2007 +0200
[FIX] Email reparation & Copyright
Both codes are written by myself without any
support from CTU
commit 0731cbae6c2feab93b244d83fd6a43f5cc9bf852
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:25:11 2007 +0200
[PATCH] Change macro name for UartLite
because PowerPC 405 can use UartLite as console
commit 1c1100d2fcf46b9d11dcf78d6e5aea75e2e8b716
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:21:19 2007 +0200
[PATCH] Add support for design without interrupt controller
Polling timer
commit 0731933ec8ec45d02ba89b52df673d526873cdde
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:19:48 2007 +0200
[FIX] resolve problem with cpu without barrel shifter
commit db14d77995ce515b728b178b63f82babe60e3d56
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:18:46 2007 +0200
[FIX] repair email address
commit 481d4328618804add1f818a6c96296121cd0528e
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:17:42 2007 +0200
[FIX] repair MFSL commands
commit b90c045f035c3cc9b5d2edaed6048dfb74e40763
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Sep 24 00:08:37 2007 +0200
synchronizition with mainline
commit 66dcad3a9a53e0766d90e0084123bd8529522fb0
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Sep 20 00:04:14 2007 +0200
v1.3.0-rc2
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 135e19bc2773ebca487e9a8371f67e1ba202313a
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Sep 18 21:36:35 2007 +0200
Avoid compiler warning.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 8a783a65851bc7421ab69f442261215e21b8891a
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Sep 18 12:24:57 2007 -0600
Bugfix: remove embedded null (\0) from CFG_BOOTFILE macro in TQM8540_config
/bin/bash and /bin/dash (which /bin/sh is linked to on ubuntu) handle embedded
nulls in a string differently. For example, the following statement:
echo "this is a string\0" > afile
Will produce the following with /bin/bash:
"this is a string\0"
But with /bin/dash, will produce:
"this is a string
Bug fixed by moving the embedded null out of the makefile and into the
config header. Also renamed the macro to avoid usage colision with the same
macro used by other board ports.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f8d3ca7b6fa322ac57e8e831f07dbeea039a9f35
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Sep 18 17:40:27 2007 +0200
MCC200: fix build warning
The MCC200 board config file includes version.h for some customer-
specific setting, which causes warnings with "make depend"; build
version.h before depend.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit bd86220f58b99d6896198c385fda132f0c980915
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 18 13:07:54 2007 +0100
Move coloured led API to status_led.h
Improve indentation in drivers/at45.c
commit e80e585b00fbbab7ad1bf71619741f2c5b029ab7
Author: Eirik Aanonsen <eaa@wprmedical.com>
Date: Tue Sep 18 08:47:20 2007 +0200
Update atstk1002 bootargs.
Updates to atstk1002 U-Boot header file:
- Changed bootargs:
* Set the bootargs for at1002 to point to the SD-card partition instead
* ... of the boot flash.
* Removing the rootfstype since that argument are not needed.
Signed-off-by: Eirik Aanonsen <eaa@wprmedical.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit a4f3aab6dfbed6c29367c688bfb8a47eef62c225
Author: Eirik Aanonsen <eaa@wprmedical.com>
Date: Wed Sep 12 13:32:37 2007 +0200
Add some comments to clocks in atstk1002.h
This patch applies some clarifying comments to how the different
clocks are setup according to atstk1002.h Some of the previous
comments where stating wrongful information.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 97213f32416ead885deafea86774e912ffd60ad0
Author: David Saada <David.Saada@ecitele.com>
Date: Mon Sep 17 17:04:47 2007 +0200
Description: Add NEC's PCI OHCI module ID to the USB OHCI driver
Signed-off-by: David Saada <david.saada@ecitele.com>
commit 30363e98fa470fbecea5e8bc0f1443352754f303
Author: Stefan Roese <sr@denx.de>
Date: Mon Sep 17 08:20:47 2007 +0200
Small whitespace cleanup of OneNAND patch
Signed-off-by: Stefan Roese <sr@denx.de>
commit d7e8ce101a4a45ed6ed45739fc2de5f87b13f7f1
Author: Kyungmin Park <kmpark@infradead.org>
Date: Mon Sep 10 17:15:14 2007 +0900
OneNAND support (take #2)
[PATCH 3/3] OneNAND support (take #2)
OneNAND support at U-Boot
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
commit 17aa2800457df0c06b41516f46f126712c196219
Author: Kyungmin Park <kmpark@infradead.org>
Date: Mon Sep 10 17:14:34 2007 +0900
OneNAND support (take #2)
[PATCH 2/3] OneNAND support (take #2)
OneNAND support at U-Boot
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
commit 916527f4809a7bcd811f1f1daf34af184e31dd8c
Author: Kyungmin Park <kmpark@infradead.org>
Date: Mon Sep 10 17:13:49 2007 +0900
OneNAND support (take #2)
[PATCH 1/3] OneNAND support (take #2)
OneNAND support at U-Boot
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
commit b49c90df6e7cfcfb8b862b8bbf8448dff5eed9a5
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Sep 16 20:51:57 2007 +0200
[FIX] remove files form repository
commit 67c31036acaaaa992fc346cc89db0909a7e733c4
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Sep 16 17:10:04 2007 +0200
TQM8xx[LM]: Fix broken environment alignment.
With recent toolchains, the environment sectors were no longer aligned to
sector boundaries. The reason was a combination of two bugs:
1) common/environment.c assumed that CONFIG_TQM8xxL would be defined
for all TQM8xxL and TQM8xxM boards. But "include/common.h", where
this gets defined, is not included here (and cannot be included
without causing lots of problems).
Added a new #define CFG_USE_PPCENV for all boards which really
want to put the environment is a ".ppcenv" section.
2) The linker scripts just include environment.o, silently assuming
that the objects in that file are really in the order in which
they are coded in the C file, i. e. "environment" first, then
"redundand_environment", and "env_size" last. However, current
toolchains (GCC-4.x) reorder the objects, causing the environment
data not to start on a flash sector boundary:
Instead of: we got:
40008000 T environment 40008000 T env_size
4000c000 T redundand_environment 40008004 T redundand_environment
40010000 T env_size 4000c004 T environment
Note: this patch fixes just the first part, and cures the alignment
problem by making sure that "env_size" gets placed correctly. However,
we still have a potential issue because primary and redundant
environment sectors are actually swapped, i. e. we have now:
40008000 T redundand_environment
4000c000 T environment
40010000 T env_size
This shall be fixed in the next version.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit eb6da8050797c204c9d010548424186c7ce32fc1
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Sep 16 02:39:35 2007 +0200
TQM8xx/FPS8xx: adjust flash partitions for 2.6 ARCH=powerpc kernels
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit cd2d1602c54cc6957bdef3872272a4b264893960
Author: urwithsughosh@gmail.com <urwithsughosh@gmail.com>
Date: Mon Sep 10 14:54:56 2007 -0400
Typo fix in tsec.c
Fixup for the break statement in wrong place.
[Patch by urwithsughosh@gmail.com]
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5bd7fe9aeb76906371f40b8fd07613f10922e3e7
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Tue Sep 11 17:04:00 2007 +0200
Fix do_div() usage in nand process output
Fix usage of do_div() in nand erase|read|write process output.
The last patch to nand_util.c introduced do_div() instead of libgcc's
implementation. But do_div() returns the quotient in its first
macro parameter and not as result.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit c750d2e6692a000a82f29de7bf24e3dc21239161
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Wed Sep 12 12:36:53 2007 +0200
NAND: Add CFG_NAND_QUIET option
This config option sets the default for the progress information
output behavior that can also be configured through the 'quiet'
environment variable.
The legacy NAND code does not print the current progress info
on the console. So this option is for backward compatibility for
units that are in the field and where setting the quiet variable
is not an option. With CFG_NAND_QUIET set to '1' the console
progress info is turned off. This can still be overwritten
through the environment variable.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit dcb88630290d2bcd803386dd4c2be73142994c4f
Author: Liew Tsi Chung-r5aahp <Tsi-chung.Liew@freescale.com>
Date: Thu Sep 13 16:06:05 2007 -0700
ColdFire: fix build error becasue of bad type of mii_init()
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 314d5b6ce52a4ed19dd295d1364e246c5e605017
Author: Liew Tsi Chung-r5aahp <Tsi-chung.Liew@freescale.com>
Date: Thu Sep 13 16:04:05 2007 -0700
ColdFire: Fix build error caused by pixis.c
Moved the #include <asm/cache.h> inside the #ifdef CONFIG_FSL_PIXIS.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit e21659e30660a1377c42af135a6114efe39801d9
Author: Sam Sparks <SSparks@twacs.com>
Date: Fri Sep 14 11:14:42 2007 -0600
Update MPC8349ITX*_config to place config.tmp in right place.
MPC834ITX*_config does not store config.tmp at the correct locatation,
causing MPC8349ITXGP to have the wrong TEXT_BASE.
Signed-off-by: Sam Sparks <SSparks@twacs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 1218abf1b5817a39a82399b4b928b00750575bda
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Sep 15 20:48:41 2007 +0200
Fix cases where DECLARE_GLOBAL_DATA_PTR was not declared as global
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 66b3f24d665be678a9dbb125b1e84185400f63b5
Author: Dirk Behme <dirk.behme@googlemail.com>
Date: Sat Sep 15 11:55:42 2007 +0200
Make DECLARE_GLOBAL_DATA_PTR global for DaVinci
As discussed in [1], DECLARE_GLOBAL_DATA_PTR has to be global and not
function local.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/31805
commit 991b089d1ce5ad945725e3657a8f106dfa02a38e
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Sep 15 00:03:35 2007 +0200
Synchronize with U-BOOT mainline
commit d7fee32b7e61fe11c64e371cde79faa4768e8350
Author: Sam Sparks <SSparks@twacs.com>
Date: Fri Sep 14 11:14:42 2007 -0600
Update MPC8349ITX*_config to place config.tmp in right place.
MPC834ITX*_config does not store config.tmp at the correct locatation,
causing MPC8349ITXGP to have the wrong TEXT_BASE.
Signed-off-by: Sam Sparks <SSparks@twacs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 6e7b7b6ea1b6d04dbe96242eb6a0c1c664c98e8c
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Thu Sep 13 18:21:48 2007 +0200
cm5200: Fix a typo introduced by afaac86fe2948ac84cd9a12bbed883b3c683e7d9
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
commit e1f601b572db5de9aa81a0b77c68a86994fe24c4
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Thu Sep 13 16:33:59 2007 +0200
tqm5200: Restore customary env. variable boot commands for powerpc kernels
- update default definitions of kernel_addr and fdt_addr env. variables
- make arch/powerpc booting the default scenario
- update MTD partition layout to match the above
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit f34024d4a328e6edd906456da98d2c537155c4f7
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Sep 12 00:48:57 2007 +0200
Fix memory corruption problem on STX GP3 SSA Board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit d94c79e47011af5e8dd10ed6163c09b4cfc743cc
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 11 15:35:01 2007 +0100
Final tidy
commit 38ad82da0c1180ecdeb212a8f4245e945bcc546e
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Tue Sep 11 15:42:11 2007 +0200
[GP3SSA] Add define CONFIG_MPC85XX_PCI2 in config file to allow u-boot to
scan on second pci bus.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 6c2f4f388e8181655ea8b69343ea00b68aa6e8d0
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Tue Sep 11 12:57:52 2007 +0200
[ppc4xx] Individual handling of sdram.c for bamboo_nand build
Bamboo has a file sdram.c which needs special treatment when building in
separate directory. It has to be linked to build directory otherwise it is
not seen.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit d45963854eff39d575124d859419bb4953ce2c87
Author: Michal Simek <monstr@monstr.eu>
Date: Tue Sep 11 00:37:04 2007 +0200
[FIX] Microblaze ML401 - repare FLASH handling
commit 38c1ef728d19950414a8ab1ccfc53767848fa346
Author: Sean MCGOOGAN <sean.mcgoogan@st.com>
Date: Mon Sep 10 16:55:59 2007 +0100
Allocate CPU Architecture Code for STMicroelectronics' ST200.
Signed-off-by: Sean McGoogan <Sean.McGoogan@st.com>
---------------------------------------------------
commit 754bac48156f8958d8f6a53a51eda88ab5758929
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Sep 10 20:42:31 2007 +0200
Update version to match current state.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 7a888d6b3c32a126dbb504ef146bb4c26574ca7b
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Mon Sep 10 17:39:08 2007 +0200
[MPC512x] Streamline frame handling in the FEC driver
- convert frame size settings to be derived from a single base
- set frame size to the recommended default value
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit e251e00d0db4b36d1d2b7e38fec43a7296b529a2
Author: Kyungmin Park <kmpark@infradead.org>
Date: Mon Sep 10 11:34:00 2007 +0900
Remove compiler warning: target CPU does not support interworking
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
commit 1d9e31e04911a6bb7cc66dd91132c699101c32e2
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Sep 9 21:21:33 2007 +0200
Fix compile error in spc1920 config.
Signed-off-by: Markus Klotzb<EFBFBD>cher <mk@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit a7d7eca791a37f452c9da10fef4b31dd7aa9a622
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Fri Sep 7 09:25:07 2007 -0600
Bugfix: make bootm+libfdt compile on boards with no flash
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 6efc1fc0b63e55f94c5bc61d8dd23c918e3bc778
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Fri Sep 7 18:35:37 2007 +0200
[PPC440SPe] PCIe environment settings for Katmai and Yucca
- 'pciconfighost' is set by default in order to be able to scan bridges
behind the primary host/PCIe
- 'pciscandelay' env variable is recognized to allow for user-controlled
delay before the PCIe bus enumeration; some peripheral devices require a
significant delay before they can be scanned (e.g. LSI8408E); without the
delay they are not detected
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 7f1913938984ef6c6a46cb53e003719196d9c5de
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Fri Sep 7 18:20:23 2007 +0200
[PPC440SPe] Improve PCIe configuration space access
- correct configuration space mapping
- correct bus numbering
- better access to config space
Prior to this patch, the 440SPe host/PCIe bridge was able to configure only the
first device on the first bus. We now allow to configure up to 16 buses;
also, scanning for devices behind the PCIe-PCIe bridge is supported, so
peripheral devices farther in hierarchy can be identified.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 15ee4734e4e08003d73d9ead3ca80e2a0672e427
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Fri Sep 7 17:46:18 2007 +0200
[PPC440SPe] Convert machine check exceptions handling
Convert using fixup mechanism to suppressing MCK for the duration of config
read/write transaction: while fixups work fine with the case of a precise
exception, we identified a major drawback with this approach when there's
an imprecise case. In this scenario there is the following race condition:
the fixup is (by design) set to catch the instruction following the one
actually causing the exception; if an interrupt (e.g. decrementer) happens
between those two instructions, the ISR code is executed before the fixup
handler the machine check is no longer protected by the fixup handler as it
appears as within the ISR code. In consequence the fixup approach is being
phased out and replaced with explicit suppressing of MCK during a PCIe
config read/write cycle.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit ff7640c9ead8806b5d827f2b29f9cb2632add729
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Sep 7 17:43:36 2007 +0200
Fix typo in MAKEALL script.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 08e2e5fcd2e06670b62e1680a3934c0e55c72810
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Fri Sep 7 17:09:21 2007 +0200
[MPC512x] Proper handling of larger frames in the FEC driver
When frame larger than local RX buffer is received, it is split and handled
by two buffer descriptors. Prior to this patch the FEC driver discarded
contents of a buffer descriptor without the 'LAST' bit set, so the first
part of the frame was lost in case of larger frames. This fix allows to
safely combine the two pieces into the whole frame.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
commit 8d17979d0359492a822a0a409d26e3a3549b4cd4
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Fri Sep 7 17:05:36 2007 +0200
[MPC512x] Correct fixup relocation
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
commit a89cbbd27a60e6740772000fd0688ffba1c2576a
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Sep 7 01:21:25 2007 +0200
Update CHANGELOG, minor coding style cleanup.
commit 5e5803e119de3bebd76fc9a57baac0b5aeccc8a3
Author: stefano babic <sbabic@denx.de>
Date: Thu Aug 30 23:01:49 2007 +0200
PXA270: Added support for TrizepsIV board.
This patch add support for the Trizeps IV module (520Mhz).
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit 80172c6181c912fbb34ea3ba0c22b232b419b47f
Author: stefano babic <sbabic@denx.de>
Date: Thu Aug 30 22:57:04 2007 +0200
PXA270: Add support for multiple serial ports.
This patch adds support for multiple serial ports to the PXA target.
FFUART, BTUART and STUART are supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit 28bb3f72c687ac6b2eb076b01dd21a5fd657d45e
Author: stefano babic <sbabic@denx.de>
Date: Thu Aug 30 22:48:47 2007 +0200
PXA270: fix compile issue (invalid lvalue)
Code is broken for PXA270 due to "invalid lvalue in assignment".
This patch fix it in pxa-regs.h
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit 1d2ca446e1a731df420206d04fe278c27ea6b8e8
Author: Jason Jin <Jason.jin@freescale.com>
Date: Thu Aug 30 18:19:05 2007 +0800
Add BUILD_DIR support for bios emulator.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit b4d8a55145442f136982634862341a3e02002bda
Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Date: Fri Aug 31 14:41:51 2007 +0900
[MIPS] Remove inline asm string functions
Stop using inline string functions on MIPS as other ARCHs do so,
since the optimized inline asm versions are not small.
This change is triggered by a following MIPS build error:
common/libcommon.a(exports.o)(.text+0xdc): In function `jumptable_init':
common/exports.c:32: undefined reference to `strcmp'
make: *** [u-boot] Error 1
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
commit 8ea2c4e54833deaebc24c3ca6b7f21353c25b0f5
Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Date: Fri Aug 31 14:41:45 2007 +0900
[MIPS] Update asm string header
This patches contains several bugfixes and cleanups in the latest upstream:
- Don't include linux/config.h
- Remove buggy inline version of memscan.
- Merge with Linux 2.6.11-rc3.
- Fix undefined reference to strcpy in binfmt_misc caused by gcc 3.4.
- Goodbye mips64. 31704 lines of code bite the dust.
- Replace extern inline with static inline.
- Fix return value of strncpy.
- Remove a bunch more "$1" clobbers.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
commit 5b729fb3bd98f49855d6bfc657c3fbae95f2adc2
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue Sep 4 17:31:22 2007 +0200
Fix do_bootm_linux() so that multi-file images with FDT blob boot.
Fix incorrect blob address calculation in do_bootm_linux() that prevents
booting the kernel from a multi-file image (kernel + initrd + blob).
Also, make minor updates to the U-Boot's output and to the coding style.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit 041a2554ad619e80dce520c1a33210affcb6a3f2
Author: Gary Jennejohn <gary.jennejohn@freenet.de>
Date: Fri Aug 31 14:29:04 2007 +0200
Add support for Sil680 IDE controller.
o add drivers/sil680.c to support the Sil680 IDE-controller.
o drivers/Makefile: add sil680.o.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
commit e79021223bc339df655e360645a52c457a74b067
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Thu Sep 6 09:47:40 2007 -0600
bootm/fdt: Only process the fdt if an fdt address was provided
Boards with CONFIG_OF_LIBFDT enabled are not able to boot old-style
kernels using the board info structure (instead of passing a device tree)
This change allows the old style booting to be used if the fdt argument
was not passed to 'bootm'.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
commit cf2817a84c2e9bea2c5dfc084bce2f2d2563ac43
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Thu Sep 6 09:46:23 2007 -0600
Migrate 5xxx boards from CONFIG_OF_FLAT_TREE to CONFIG_OF_LIBFDT
Affects boards: icecube (lite5200), jupiter, motionpro, tqm5200
Tested on: lite5200b
Note: the fixup functions have not been moved to a common place. This
patch is targeted for immediate merging as in solves a build issue, but
the final name/location of the fixups is still subject to debate. I
propose to merge this now, and move the fixups in the next merge window
to be usable by all targets.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 41bb76e941929f54a73206fb132f7a4c275543a3
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Thu Sep 6 09:46:17 2007 -0600
libfdt: add convenience function fdt_find_and_setprop()
Given the path to a node, fdt_find_and_setprop() allows a property value
to be set directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 80767a6cead9990d9e77e62be947843c2c72f469
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed Sep 5 16:04:41 2007 +0100
Changed API name to coloured_led.h
Removed code using deprecated ifdef CONFIG_BOOTBINFUNC
Tidied other cpu/arm920t/start.S code
commit 56a9270521baaa00e12639a978302a67f61ef060
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Thu Aug 30 16:18:18 2007 -0500
Fix ULI RTC support on MPC8544 DS
The RTC on the M1575 ULI chipset requires a dummy read before
we are able to talk to the RTC. We accomplish this by adding a
second memory region to the PHB the ULI is on and read from it.
The second region is added to maintain compatiabilty with Linux's
view of the PCI memory map.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit f75e89e9b5714db2b0e80074071dfbdd6f59488a
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Thu Aug 30 01:58:48 2007 -0500
ft_board_setup update 85xx/86xx of pci/pcie bus-range property.
pcie is now differentiated from pci. Add 8641 bus-range updates.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 9f5c3d3720e777a572dcdc8af2008b44c7243885
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 4 16:18:38 2007 +0100
Add coloured led interface for ARM boards.
Use it in cpu/arm920t/start.S to indicate U-Boot code has been entered.
commit 7462fe0d5a9d40cde083fb1a3cd73911996b5ecb
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 4 14:49:28 2007 +0100
Move include/led.h to board/at91rm9200dk
commit 6e4bf9b24e57c15abc6542e685d06380bc64af27
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 4 14:25:51 2007 +0100
Ran Lindent on drivers/at45.c
commit 557ab89d294f08dd532f21d19861b40093200a33
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Sep 4 14:23:50 2007 +0100
Rename CONFIG_CMD_MUX to CONFIG_CMD_AT91_SPIMUX
commit 81b73dec16fd1227369a191e725e10044a9d56b8
Author: Gary Jennejohn <garyj@denx.de>
Date: Fri Aug 31 15:21:46 2007 +0200
ppc4xx: (Re-)Enable CONFIG_PCI_PNP on AMCC 440EPx Sequoia
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.
Here the details of this patch:
o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
board-specific settings. As an example the sequoia board requires 0.
Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
CFG_PCI_CACHE_LINE_SIZE to 0.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 60174746c668b309378a91488dded898e9553eae
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Aug 31 10:01:51 2007 +0200
Fix TFTP OACK code for short packets.
The old code had a loop limit overflow bug which caused a semi-
infinite loop for small packets, because in "i<len-8", "i" was signed,
but "len" was unsigned, and "len-8" became a huge number for small
values of "len".
This is a workaround which replaces broken commit 8f1bc284.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 696dd1307cd8e73a10e9bb3c51731bfd6f837bee
Author: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Date: Thu Aug 30 15:03:05 2007 +0200
Reduce BOOTDELAY variable to 1 second by default for STK1002
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit c88b6e1cbf9a8ae2a34fb602f78a1bf4e6692b6a
Author: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Date: Thu Aug 30 15:03:04 2007 +0200
Remove double quotation marks around MAC address for STK1002
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit ff13ac8c7bbebb238e339592de765c546dba1073
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 30 14:42:15 2007 +0200
Backout commit 8f1bc284 as it causes TFTP to fail.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 1900fbf255acba8b94fb442a16408ea85a1d46a6
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Thu Aug 30 02:26:17 2007 -0500
Revert "Fix MPC8544DS PCIe3 scsi."
This reverts commit 9468e680.
Commit 16e23c3f5da removing allocation of PCSRBAR is sufficient.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 8f1bc28408ded213418d9bc0780c7d8fb8a03774
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Wed Aug 29 18:26:24 2007 -0600
tftp: don't implicity trust the format of recevied packets
The TFTP OACK code trusts that the incoming packet is formated as
ASCII text and can be processed by string functions. It also has a
loop limit overflow bug where if the packet length is less than 8, it
ends up looping over *all* of memory to find the 'blksize' string.
This patch solves the problem by forcing the packet to be null
terminated and using strstr() to search for the sub string.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 04625764cc93ce8a61625ac19d7fe2a2ceee8143
Author: Stefan Roese <sr@denx.de>
Date: Wed Aug 29 16:31:18 2007 +0200
ppc4xx: Change lwmon5 default environment to support Linux RTC
The Linux PCF8563 RTC driver doesn't do autoprobing, so we need
to supply the RTC I2C address as bootline parameter. This patch
adds support for this rtc probing parameter to the bootargs:
"rtc-pcf8563.probe=0,0x51"
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2602a5c40ae37ab965a4e240854fdaffb51328a4
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 29 09:06:05 2007 -0500
sbc8641: remove unused OF_FLAT_TREE_MAX_SIZE
this had slipped through the cracks, since the sbc board was added
after I wrote the original patch to remove all these symbols, and
before it was merged.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit c5bded3c88e48ae648a75d357dc81a8255fa81f1
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Aug 29 14:05:30 2007 +0200
Add mii_init() prototype
to get rid of a *lot* of compiler warnings.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 2d1f23aa1e74e4a8f8ffa67f246eb98c522dfd7f
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Aug 29 13:35:03 2007 +0200
Disable network support on cmi_mpc5xx board
..because it caused compiler errors and there seems to be no
board maintainer to take care of this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 9468e6804b7e25b0f6f52e53f47bce3175400a16
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Mon Aug 20 09:44:00 2007 -0500
Fix MPC8544DS PCIe3 scsi.
<ed.swarthout@freescale.com>
The problem is pciauto_setup_device() getting called from fsl_pci_init.c
is allocating memory space it doesn't need.
Signed-off-by: Ed Swarthout <ed.swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 4bf4abb8a4e9955556b120a1aafa30c03e74032a
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Tue Aug 21 09:38:59 2007 -0500
8548cds fixes
Restore CONFIG_EXTRA_ENV_SETTINGS definition which contains the
correct consoledev needed for linux boot.
Standardize on fdt{file,addr} var to hold dtb file name.
Set PCI inbound memory region from CFG_MEMORY_{BUS,PHYS}.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 7a1ac419fa0d2d23ddd08bd61d16896a9f33c933
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Thu Aug 23 15:20:54 2007 -0400
Enable L2 cache for MPC8568MDS board
The L2 cache size is 512KB for 8568, print out the correct informaiton.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit 94c47fdaf14cb29fa3fb4d4da2efdd96c803b46b
Author: Jason Jin <Jason.jin@freescale.com>
Date: Wed Aug 22 17:54:49 2007 +0800
Remove the bios emulator binary files from MAI board
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 7608d75f9c87c9eb5b3a43219d0506d3e979a13f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Aug 21 17:00:17 2007 -0500
support board vendor-common makefiles
if a board/$(VENDOR)/common/Makefile exists, build it.
also add the first such case, board/freescale/common/Makefile, to
handle building board-shared EEPROM, PIXIS, and MDS-PIB code, as
dictated by board configuration.
thusly get rid of alternate build dir errors such as:
FATAL: can't create /work/wd/tmp/u-boot-ppc/board/freescale/mpc8360emds/../common/pq-mds-pib.o: No such file or directory
by putting the common/ mkdir command in its proper place (the common
Makefile). Common bits from existing individual board Makefiles have
been removed.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit ef8f20752712dc1cdbd86f47e3bd6e35f81c83fd
Author: stefano babic <sbabic@denx.de>
Date: Tue Aug 21 15:52:33 2007 +0200
Fix: TFTP is not working on little endian systems
TFTP does not work anymore after multicast tftp
patch was applied on little endian systems.
This patch fix it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit 5f470948570526e9186f053a3003da7719604e90
Author: stefano babic <sbabic@denx.de>
Date: Tue Aug 21 15:50:33 2007 +0200
Fix MAC address setting in DM9000 driver.
The logic to check if there is a correct MAC address in the DM9000
EEPROM, added in the last patch, is wrong. Now the MAC address is
always taken from the environment, even if a suitable MAC is present
in the EEPROM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit 4a8527ef086ec7c89f40674ef024ae6f988a614a
Author: Martin Krause <martin.krause@tqs.de>
Date: Tue Aug 21 12:40:34 2007 +0200
MPC5xxx: fix some compiler warnings in USB code
Fix the following warnings:
- usb.c:xx: warning: function declaration isn't a prototype
- usb_ohci.c:xxx: warning: passing argument 1 of '__fswab32' makes integer
from pointer wihtout a cast
Signed-off-by: Martin Krause <martin.krase@tqs.de>
commit 16e23c3f5dab6937f5109365416808c7f15c122b
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Mon Aug 20 23:55:33 2007 -0500
fsl_pci_init - Remove self PCSRBAR allocation
CPU physical address space was being wasted by allocating a
PCSRBAR PCI inbound region to it's memory space.
As a rule, PCSRBAR should be left alone since it does not affect
transactions from self and other masters may have changed it.
Signed-off-by: Ed Swarthout <ed.swarthout@freescale.com>
commit 0e700ce03a23bb1921149bc77008ace7103d5289
Author: Martin Krause <martin.krause@tqs.de>
Date: Mon Aug 20 13:56:47 2007 +0200
Fix compiler warning in include/s3c2410.h
This patch fixes the "type qualifiers ignored on fuction return tpye"
warning for include/s3c2410.h
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit 9bb8b209ed2058a5756ecbeb544c067e44a42aea
Author: Dirk Behme <dirk.behme@googlemail.com>
Date: Mon Aug 20 07:09:05 2007 +0200
Fix compilation error for omap2420h4_config.
omap2420h4 switched to cfi, so remove old (already disabled) flash.c
and flash_probe() calls in env_flash.c.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
commit 3bb342fc85d79dbb6b8c2039e7cdcddc82b8d90f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Fri Aug 10 14:34:14 2007 -0500
fdt: remove unused OF_FLAT_TREE_MAX_SIZE references
and make some minor corrections to the FDT part of the README.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 6af2eeb1e99c2dcc584d4c5ab7fcae30a325f4de
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Aug 29 01:32:05 2007 +0200
Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit a861558c65f65f1cf1302f3a35e9db7686b9e1a3
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Tue Aug 28 17:40:33 2007 +0200
[UC101] Fix: if no CF in the board, U-Boot resets sometimes.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit f98984cb194bb34dbe1db9429d3b51133af30d07
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Tue Aug 28 17:39:14 2007 +0200
IDE: - make ide_inb () and ide_outb () "weak", so boards can
define there own I/O functions.
(Needed for the pcs440ep board).
- The default I/O Functions are again 8 Bit accesses.
- Added CONFIG_CMD_IDE for the pcs440ep Board.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 2c05fd125744981e5f2828d24e66ccc20a77d25d
Author: Semih Hazar <semih.hazar@indefia.com>
Date: Mon Aug 20 19:00:01 2007 +0300
AVR32: Change prototype of memset
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 9c02defc29b57945b600714cf61ddfd02b02fb14
Author: Yuri Tikhonov <yur@emcraft.com>
Date: Sat Aug 25 05:07:16 2007 +0200
POST: limit memory test area to not touch global data anymore
As experienced on lwmon5, on some boards the POST memory test can
corrupt the global data buffer (bd). This patch fixes this issue
by checking and limiting this area.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 75e1a84d483e36be10e206e539b028c4889e1158
Author: Stefan Roese <sr@denx.de>
Date: Fri Aug 24 15:41:42 2007 +0200
ppc4xx: Add RTC POST test to lwmon5 board configuration
Since this RTC POST test is taking quite a while to complete
it's only initiated upon special keypress same as the complete
memory POST.
Signed-off-by: Stefan Roese <sr@denx.de>
commit d7bfa620037a6d2210159387571bdf93aa32c162
Author: Stefan Roese <sr@denx.de>
Date: Fri Aug 24 15:19:10 2007 +0200
ppc4xx: Change GPIO signal for watchdog triggering on lwmon5
Signed-off-by: Stefan Roese <sr@denx.de>
commit c25dd8fc25e9ca3695db996a257d9ba4dab414db
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 23 11:02:37 2007 +0200
ppc4xx: Add support for 2nd I2C EEPROM on lwmon5 board
This patch adds support for the 2nd EEPROM (AT24C128) on the lwmon5
board. Now the "eeprom" command can be used to read/write from/to this
device. Additionally a new command was added "eepromwp" to en-/disable
the write-protect of this 2nd EEPROM.
The 1st EEPROM is not affected by this write-protect command.
Signed-off-by: Stefan Roese <sr@denx.de>
commit c64fb30e4c5976007d56fc1789c7a0666082b536
Author: Stefan Roese <sr@denx.de>
Date: Wed Aug 22 08:56:09 2007 +0200
ppc4xx: Remove unused option CFG_INIT_RAM_OCM
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3ad63878737a5a2b1e60825bf0a7d601d7a695e7
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 21 16:27:57 2007 +0200
ppc4xx: Add matrix kbd support to lwmon5 board (440EPx based)
This patch adds support for the matrix keyboard on the lwmon5 board.
Since the implementation in the dsPCI is kind of compatible with the
"old" lwmon board, most of the code is copied from the lwmon
board directory.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3e66c078003607a7d1d214c15a5f262bc1b4032f
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 19 10:27:34 2007 +0200
Fix some build errors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 05675735ef77dc23b5e0eb782bad1ff477b55e86
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Aug 18 22:00:38 2007 +0200
Update CHANGELOG.
commit 79f240f7ecc0506b43ac50d1ea405ff6540d4d57
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Aug 16 22:52:39 2007 -0500
lib_ppc: make board_add_ram_info weak
platforms wishing to display RAM diagnostics in addition to size,
can do so, on one line, in their own board_add_ram_info()
implementation.
this consequently eliminates CONFIG_ADD_RAM_INFO.
Thanks to Stefan for the hint.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 815b5bd5b18569917c3e04b9757511e6ed23b9f6
Author: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Date: Fri Aug 17 12:43:44 2007 +0900
PCI_READ_VIA_DWORD_OP: Fix *val uninitialized bug
This patch has been sent on:
- 6 Jun 2007
Many users of PCI config read routines tend to ignore the function
ret value, and are only concerned about the contents of *val. Based
on this, pci_hose_read_config_{byte,word}_via_dword should initialize
the *val on dword read error.
Without this fix, for example, we'll go on scanning bus with vendor or
header_type uninitialized. This brings many unnecessary config trials.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
commit 26667b7fa05a8bf2fc65fb9f3230b02b1a10c367
Author: Stefan Roese <sr@denx.de>
Date: Sat Aug 18 14:37:52 2007 +0200
ColdFire: Fix some remaining problems with CFG_CMD_
Signed-off-by: Stefan Roese <sr@denx.de>
commit 8280f6a1c43247616b68224675188e5ccd124650
Author: Stefan Roese <sr@denx.de>
Date: Sat Aug 18 14:33:02 2007 +0200
Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4a442d3186b31893b4f77c6e82f63c4517a5224b
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Aug 16 19:23:50 2007 -0500
ColdFire: Add M5235EVB Platform for MCF523x
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 4cc1cd5941827a04cf5c51a07fcc42e8945894aa
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Fri Aug 17 09:30:00 2007 -0500
mpc83xx: fix typo in DDR2 programming
introduced in the implement board_add_ram_info patch as I was cleaning out the
magic numbers. sorry.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit e58fe95784d2514fc9c21028dc59f2b319a35d80
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Aug 16 22:53:09 2007 -0500
mpc83xx: move freescale boards to boards/freescale
includes build fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 5aa4ad8d8e7e9468219990c7875d5fdc9e962f47
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Aug 16 22:52:59 2007 -0500
mpc83xx: suppress unused variable 'val8' warning
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit bbea46f76f767b919070b4829bf34c86bd223248
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Aug 16 22:52:48 2007 -0500
mpc83xx: implement board_add_ram_info
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 14778585d1389d86d5846efec29e5fce892680ce
Author: Tony Li <tony.li@freescale.com>
Date: Fri Aug 17 10:35:59 2007 +0800
mpc83xx: Split PIB init code from pci.c and add Qoc3 ATM card support
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c
And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board.
Signed-off-by Tony Li <tony.li@freescale.com>
commit 8ae158cd87a4a25722b27835261b6ff0fa2aa6a7
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Aug 16 15:05:11 2007 -0500
ColdFire: Add M54455EVB for MCF5445x
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit a1436a842654a8d3927d082a8ae9ee0a10da62d7
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Aug 16 13:20:50 2007 -0500
ColdFire: Add M5253EVBE platform for MCF52x2
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit a605aacd8324094199402816cc6d9124aba57b8d
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Aug 16 05:04:31 2007 -0500
ColdFire: Add M5249EVB platform for MCF52x2
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit f28e1bd9daa6de5eb33ae4822bda6b008ccb4e9e
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 20:32:06 2007 -0500
ColdFire: Update Freescale MCF52x2 platforms
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 870470dbf6f4bb9864e0d97aeedbc17c167c6d1c
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:55:10 2007 -0500
ColdFire: Update EB+MCF-EV123 platform
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit aa93d859d9b1fcd8eea52d51b06e86c38f72111b
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:46:38 2007 -0500
ColdFire: update TASREG platform for MCF52x2
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit a9505510bf56a9b5558248dd8b73ec9d9a1556a2
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:45:51 2007 -0500
ColdFire: update r5200 platform for MCF52x2
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 6cfd3c7bc813fb317ab7c0781f0d1874b1c0877c
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:43:20 2007 -0500
ColdFire: idmr platform MCF52x2 update
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 6706424d0bb851fb52af00cd1c3301e91ee7f2b0
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:41:06 2007 -0500
ColdFire: cobra5272 platform for MCF52x2 update
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 56115665b4a64c10c01440c57749b265e0908fa4
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:38:15 2007 -0500
ColdFire: MCF52x2 Header files update
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 83ec20bc4380eebddfde45da6e3a69a92d4db21d
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 19:21:21 2007 -0500
ColdFire: MCF52x2 update
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit f52e78304dcc0ac459c0ea1fa5be275c7d1642cf
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 18:46:11 2007 -0500
ColdFire: MCF5329 update cache
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 7171977fb8fd77cfb6676953fa9a05789c450513
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 15:40:20 2007 -0500
ColdFire: MCF5329 header file clean up
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit ab77bc547ba561c25ea34457ed17aa0b2f7c2723
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Wed Aug 15 15:39:17 2007 -0500
ColdFire: MCF5329 Update and cleanup
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 10327dc5541f947c0cf7e31fef86c4706169607a
Author: Andy Fleming <afleming@freescale.com>
Date: Thu Aug 16 16:35:02 2007 -0500
Add CONFIG_HAS_ETH0 to all boards with TSEC
The 85xx code now relies on CONFIG_HAS_ETH0 to determine whether
to update TSEC1's device-tree node, so we need to add it
to all the boards with TSECs. Do this for 83xx and 86xx, too,
since they will eventually do something similar.
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit d64ee908a1b525e5bb2b4cbeb5c449ad6a469666
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Thu Aug 16 15:05:04 2007 -0500
Update MPC8544 DS PCI memory map
The PCIe bus that the ULI M1575 is connected to has no possible way of
needing more than the fixed amount of IO & Memory space needed by the ULI.
So make it use far less IO & memory space and have it use the shared LAW. This
free's up a LAW for PCIe1 IO space. Also reduce the amount of IO space needed
by each bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit ea5877e31ed63ade948fd1293895ec23fe01472e
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Thu Aug 16 11:01:21 2007 -0500
Fix up some fdt issues on 8544DS
It looks like we had a merge issue that duplicated a bit of code
in ft_board_setup. Also, we need to set CONFIG_HAS_ETH0 to get
the MAC address properly set in the device tree on boot for TSEC1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 07bc20560cb9d3d186cca268c05c82762e8c55ad
Author: Niklaus Giger <niklaus.giger@netstal.com>
Date: Thu Aug 16 15:16:03 2007 +0200
PPC4xx:HCU4/5 cleanup
Minor cleanups to confirm to the u-boot coding style.
Some german expressions -> english.
HCU5 enforces a unique IP adress for a given slot in the rack.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 1e6b07c64967c1eb2cd84faa4c32bf2a769bc8eb
Author: Niklaus Giger <niklaus.giger@netstal.com>
Date: Thu Aug 16 15:16:02 2007 +0200
PPC4xx:HCU4/5 cleanup ecc/sdram init
Make ecc initialisation robust, as DDR2-ECC errors may be generated
while zeroing the RAM.
Return 16 bytes (a cacheline) less than the available memory, as the
board and/or PPC440EPx might have problems accessing the last bytes.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit d35b508a55508535b6e8445b718585d27df733d3
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:29:56 2007 -0500
fdt: suppress unused variable 'bd' warning
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 82bd9ee77490588d4da785d75829ca63d0176baf
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 20:06:50 2007 -0500
Fix warnings from of_data copy fix
Forgot to cast of_flat_tree to ulong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 7613afda77d5eec0f47d303025b0c661b70e4c73
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 20:03:44 2007 -0500
Don't wait for disconnected TSECs
The TSEC driver's PHY code waits a long time for autonegotiation to
complete, even if the link is down. The PHY knows the link is
down or up before autonegotiation completes, so we can short-circuit
the process if the link is down.
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit b96c83d4ae475a70ef2635cd0e748174c44c8601
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 20:03:34 2007 -0500
Fix numerous bugs in the 8568 UEC support
Actually, fixed a large bug in the UEC for *all* platforms.
How did this ever work?
uec_init() did not follow the spec for eth_init(), and returned
0 on success. Switch it to return the link like tsec_init()
(and 0 on error)
The immap for the 8568 was defined based on MPC8568, rather than
CONFIG_MPC8568
CONFIG_QE was off
CONFIG_ETHPRIME was set to "Freescale GETH". Now is "FSL UEC0"
Fixed a comment about the ranges for CONFIG_ETHPRIME if TSEC_ENET is
enabled
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 3a79013e2adda53332dfd0b511066a805e929a9d
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 20:03:25 2007 -0500
Define tsec flag values in config files
The tsec_info structure and array has a "flags" field for each
ethernet controller. This field is the only reason there are
settings. Switch to defining TSECn_FLAGS for each controller
in the config header, and we can greatly simplify the array, and
also simplify the addition of future boards.
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit ec7238229507e7f47533a611ea8c53319d234cf3
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 20:03:13 2007 -0500
Add support for building all boards with a TSEC
Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards.
Now we can do a MAKEALL test on all of them!
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 10aaf716cb0dc6614df54ef78bed5144afd23ef8
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Aug 15 17:30:56 2007 -0500
Fix of_data copying for CONFIG_OF_FLAT_TREE-using boards
The fix, "Fix where the #ifdef CFG_BOOTMAPSZ is placed"
neglected to *also* put the code inside the similar #ifdef
for CONFIG_OF_FLAT_TREE.
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 78f9fef7f406078c8bf7191e665a73f795157746
Author: Scott Wood <scottwood@freescale.com>
Date: Wed Aug 15 15:46:46 2007 -0500
mpc885ads: Don't define CONFIG_BZIP2.
bzip2 requires a significant chunk of malloc space, and there isn't
enough room on mpc885ads (with only 8MB RAM) for both bzip2's malloc area
and a downloaded image at 0x400000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 002275a3ed8b114885f6702d6d544d0780dfe689
Author: Michal Simek <Monstr@seznam.cz>
Date: Thu Aug 16 08:54:10 2007 +0200
Bios emulator - fix microblaze toolchain problem
microblaze CPU have problem with bios_emulator code.
Microblaze toolchain doesn't support PRAGMA PACK.
Signed-off-by: Michal Simek <monstr@monstr.eu>
commit a5a38f4fd7e5366d706ff6a985f9b6715ddbc98b
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 16 11:51:04 2007 +0200
Minor Coding Style fix; Update CHANGELOG file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 8fb6e80c06849e3013ac5c9350d8ed9e52967991
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 16 11:21:49 2007 +0200
ppc4xx: Remove #warning in esd auto_update.c
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2d78074d2e806edc380c1464eb9e5df335ece65e
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 22 17:32:28 2007 +0200
ppc7xx: Update CPCI750 board
This small CPCI750 update extends the board specific command
"show_config" to display the Marvell strapping registers and
extends the PCI IDE controller.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 78cff50edba6b1508eb15c2f53ce966ac891eb9e
Author: Michal Simek <monstr@monstr.eu>
Date: Thu Aug 16 10:46:28 2007 +0200
[FIX] Changes for bios_emulator code for others architecture
commit 6e0e2253f039344f8ebd2787285fdba90e6714e8
Author: Michal Simek <monstr@monstr.eu>
Date: Thu Aug 16 10:45:09 2007 +0200
[FIX] Remove unused include file
commit 9de469bd960cc1870bb40d6672ed42726b8b50d7
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 16 10:18:33 2007 +0200
ppc4xx: Only enable POST FPU test on Sequoia and not Rainier
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6da0c5bd4a53e40eb4f7eb72a4c051ecabad783c
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 16 09:54:51 2007 +0200
Add missing rainier (PPC440GRx) target to MAKEALL and MAINTAINERs files
Signed-off-by: Stefan Roese <sr@denx.de>
commit 02ba7022f62bb75908296c58c63866e1d294b69a
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 16 09:52:29 2007 +0200
ppc4xx: Update Sequoia/Rainier bootstrap command
As suggested by David Mitchell, here an update for the Sequoia/Rainier
bootstrap command.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 35cc4e4823668e8745854899cfaedd4489beb0ef
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:39 2007 -0500
mpc83xx: enable libfdt by default on freescale boards
this enables libfdt code by default for the
freescale mpc8313erdb, mpc832xemds, mpc8349emds,
mpc8349itx and gp boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 3fde9e8b22cfbd7af489214758f9839a206576cb
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:33 2007 -0500
mpc83xx: migrate remaining freescale boards to libfdt
this adds libfdt support code for the freescale
mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx,
and gp boards.
Boards remain compatible with OF_FLAT_TREE.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 6a16e0dfcc4119b46adb1dce2d6c8fb3c5d108e1
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:26 2007 -0500
mpc83xx: move common /memory node update mechanism to cpu.c
also adds common prototypes to include/common.h.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 8f9e0e9f339aee4ce31a338d5f27356eb5457f85
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:19 2007 -0500
mpc83xx: remaining 8360 libfdt fixes
PCI clocks and QE frequencies weren't being updated, and the core clock
was being updated incorrectly. This patch also adds a /memory node if
it doesn't already exist prior to update.
plus some cosmetic trimming to single line comments.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit f4b2ac5ed9aaff9920d487bff8a59696c083a524
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:12 2007 -0500
mpc83xx: fix UEC2->1 typo in libfdt setup code
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 19fa1c35368484d4ed10ddce8a7793c21862e3a3
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Aug 15 22:30:05 2007 -0500
mpc83xx: add MAINTAINER and MAKEALL entries for the mpc8323erdb
and reorder the existing 83xx maintainers alpha.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 5b4de9309d7a03aa1db2e5391ab696363391f460
Author: Michal Simek <monstr@monstr.eu>
Date: Wed Aug 15 21:15:05 2007 +0200
[FIX] Resolve problem with warnings
microblaze toolchain don't support PRAGMA PACK.
commit d1ed28cf36ab6b1d4c479809de7252bf53d2f2d4
Author: Michal Simek <monstr@monstr.eu>
Date: Wed Aug 15 21:05:07 2007 +0200
[FIX] Correction command setting for Microblaze boards
commit 7aa63d8cd30ab20ac2fd1ab86e60471de8b1f1e5
Author: Michal Simek <monstr@monstr.eu>
Date: Wed Aug 15 21:03:41 2007 +0200
[FIX] Correction command definition
commit 30b52df9e906bf0e465916c2c6bb5192b438e0b8
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Aug 15 11:55:35 2007 -0500
86xx: Fix lingering CFG_CMD_* references in sbc8641d.h
Remove a leftover in net/tftp.c while we're at it.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4ce917742b1e48faa9bf9a9757545e56fb4cfe44
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Aug 15 12:20:40 2007 -0500
Move the MPC8641HPCN board under board/freescale.
Minor path corrections needed to ensure buildability.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 8662577fe36fdb6a44b55b998d9daac6392a736a
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Aug 15 11:46:22 2007 -0500
86xx: Fix lingering CFG_CMD_* references in sbc8641d.h
Remove a leftover in net/tftp.c while we're at it.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 210f463c71917b7a4495c2103c228b9c179ae64d
Author: Jerry Van Baren <gvb.uboot@gmail.com>
Date: Wed Aug 15 11:13:15 2007 -0400
Fix where the #ifdef CFG_BOOTMAPSZ is placed.
Commit 073e1b509980cefe6f53c2d7fbbcd135df1e3924 "Fix initrd/dtb
interaction" put the new code outside of the #if defined(CONFIG_OF_LIBFDT)
when it should have gone inside of the conditional. As a result, it
broke non-LIBFDT board builds.
Also added a missing "not." to the comment.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 0e19209767194a97cec6d93dba9e64d1da8d548e
Author: Niklaus Giger <niklaus.giger@netstal.com>
Date: Wed Aug 15 12:14:23 2007 +0200
PPC4xx:HCU4/5-Board fix compile warning
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 594e79838ce5078a90d0c27abb2b2d61d5f8e8a7
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Tue Aug 14 14:06:45 2007 -0500
Fix malloc size error in ahci_init_one.
Typically this causes scsi init to corrupt the
devlist and break the coninfo command.
Fix a compiler size warning.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit b361acd64fd2525c081b9b288b0804efe209c0e9
Author: ksi@koi8.net <ksi@koi8.net>
Date: Tue Aug 14 10:02:16 2007 -0700
TI DaVinci - fix unsupported %hhx format
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
commit f01dbb5424a81453c81190dd30e945891466f621
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Aug 14 18:42:36 2007 +0200
Coding style cleanup. Update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 073e1b509980cefe6f53c2d7fbbcd135df1e3924
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 10:32:59 2007 -0500
Fix initrd/dtb interaction
The original code would wrongly relocate the blob to be right before
the initrd if it existed. The blob *must* be within CFG_BOOTMAPSZ,
if it is defined. So we make two changes:
1) flag the blob for relocation whenever its address is above BOOTMAPSZ
2) If the blob is being relocated, relocate it before kbd, not initrd
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit e54b970173769307a116bd34028b6d0c2eea2a4e
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 15:40:00 2007 +0100
Supply spi interface in at45.c
commit 4ce846ec59f36b85d6644a769690ad3feb667575
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 14 15:12:01 2007 +0200
POST: Fix merge problem
Signed-off-by: Stefan Roese <sr@denx.de>
commit 429d9571f60631ae8a2fe12b11be4c75b0c2b37c
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 14 15:03:17 2007 +0200
Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 779e975117a75e91fcebe226a63104dbfb924ab1
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 14 14:44:41 2007 +0200
ppc4xx: Add initial Zeus (PPC405EP) board support
Signed-off-by: Stefan Roese <sr@denx.de>
commit c5a172a5fd636c12467429e3f7910e53773979c6
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 14 14:41:55 2007 +0200
POST: Add option for external ethernet loopback test
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST
is not done using an internal loopback connection, but by assuming
that an external loopback connector is plugged into the board.
Signed-off-by: Stefan Roese <sr@denx.de>
commit eb2b4010ae426245172988804ee8d9193fb41038
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 14 14:39:44 2007 +0200
POST: Add ppc405 support to cache and UART POST
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0c42f36f15074bd9808a7dbd7ef611fad9bf537c
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:46:32 2007 +0100
Replace lost end of at45.c.
commit 65d7ada64557e76094b4fd3bad30a0f18f5fb2b2
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:30:06 2007 +0100
Update Makefiles for merged and split at45.c.
commit 3454cece2db57cb9eb7087995f7e73066a163f71
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:21:06 2007 +0100
Delete the merged files.
commit dcbfd2e5649f97aa04fbbc6ea2b008aa4486e225
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:14:05 2007 +0100
Add the files.
commit d4fc6012fd0a5c211b825691f44b06f8032c0551
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Aug 14 10:10:52 2007 +0100
Add MACH_TYPE records for several AT91 boards.
Merge to two at45.c files into a common file, split to at45.c and spi.c
Fix spelling error in DM9161 PHY Support.
Initialize at91rm9200 board (and set LED).
Add PIO control for at91rm9200dk LEDs and Mux.
Change dataflash partition boundaries to be compatible with Linux 2.6.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
commit 4ef35e53c693556c54b0c22d6f873de87bade253
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Aug 14 09:54:46 2007 +0200
Coding style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 85eb5caf6b906f7ec5b54814e8c7c74f55986bb7
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Aug 14 09:47:27 2007 +0200
Coding style cleanup; rebuild CHANGELOG
commit 7f3f2bd2dc08e0b05e185662ca2e2d283757104a
Author: Randy Vinson <rvinson@linuxbox.(none)>
Date: Tue Feb 27 19:42:22 2007 -0700
85xxCDS: Add make targets for legacy systems.
The PCI ID select values on the Arcadia main board differ depending
on the version of the hardware. The standard configuration supports
Rev 3.1. The legacy target supports Rev 2.x.
Signed-off-by Randy Vinson <rvinson@mvista.com>
commit e41094c7e38177c755fbd9b182018069614f080d
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 01:50:09 2007 -0500
85xxCDS: Enable the VIA PCI-to-ISA bridge.
Author: Randy Vinson <rvinson@linuxbox.(none)>
Enable the PCI-to-ISA bridge in the VIA Southbridge located on the
Arcadia main board.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: York Sun <yorksun@freescale.com>
commit da9d4610d76e52c4d20a8f3d8433439a7fcf5b71
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 00:14:25 2007 -0500
Add support for UEC to 8568
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit c59e4091ffe0148398b9e9ff14a019ea038b7432
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Tue Jun 19 14:18:34 2007 -0400
Add PCI support for MPC8568MDS board
This patch is against u-boot-mpc85xx.git of www.denx.com
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
commit d111d6382c99fdea08c2312eeeae8786945e189a
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Tue Jun 19 14:18:32 2007 -0400
Empirically set cpo and clk_adjust for mpc85xx DDR2 support
This patch is against u-boot-mpc85xx.git of www.denx.com
Setting cpo to 0x9 for frequencies higher than 333MHz is verified on
both MPC8548CDS board and MPC8568MDS board, especially for supporting
533MHz DDR2.
Setting clk_adjust to 0x6(3/4 late cycle) for MPC8568MDS board is for
DDR2 on all current board versions especially ver 1.92 or later to bring
up.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit 3db0bef59eab1155801618cef5c481e97553b597
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue Aug 7 18:07:27 2007 -0500
Use an absolute address when jumping out of 4k boot page
On e500 when we leave the 4k boot page we should use an absolute address since
we don't know where the board code may want us to be really running at.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 39980c610c9a4c381907c9e1d1b9c0e1c0dca57a
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Aug 13 14:49:59 2007 -0500
MPC85xx BA bits not set for 3-bit bank address DIMM
The current implementation does not set the number of bank address bits
(BA) in the processor. The default assumes 2 logical bank bits. This
works fine for a DIMM that uses devices with 4 internal banks (SPD
byte17 = 0x4) but needs to be set appropriately for a DIMM that uses
devices with 8 internal banks (SPD byte17 = 0x8).
Signed-off-by: Greg Davis <DavisG@embeddedplanet.com>
commit 6c543597bb4b1ecf5d8589f7abb0f39929fb7fd1
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Aug 13 14:38:06 2007 -0500
Fix minor 85xx warnings
Some patches had inserted warnings into the build:
* mpc8560ads declared data without using it
* cpu_init declared ecm and immap without using it in all CONFIGs
* MPC8548CDS.h had its default filenames changed so that they contained
"\m" in the paths. Made the defaults not Windows-specific (or
anything-specific)
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit f2cff6b104f82b993bef6086ce0c97159bbe1add
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:52 2007 -0500
8548cds PCIE support.
Make the early L1 cache stack region guarded to prevent speculative
fetches outside the locked range.
Use _PHYS defines, not _MEM for cpu-side PCI memory mapped regions.
init.S whitespace cleanup.
Allow TEXT_BASE value to be specified on command line. This allows it
to be set to 0xfffc0000 which cuts the uboot binary in half.
Clear and enable lbc and ecm errors.
Update last_busno in device-tree for pci and pcie.
Remove load of obsolete cpu/mpc85xx/pci.0
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 837f1ba05cfb248aba5ab8e1fb1bfeefa07d5962
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:51 2007 -0500
8544ds PCIE support
PCI1 LAW mapping should use CFG_PCI1_MEM_PHY and not _BASE address.
Enable LBC and ECM errors and clear error registers.
Add tftpflash env var to get uboot from tftp server and flash it.
Add pci/pcie convenience env vars to display register space:
"run pcie3regs" to see all pcie3 ccsr registers
"run pcie3cfg" to see all cfg registers
Whitespace cleanup and MPC8544DS.h
Enable CONFIG_INTERRUPTS.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 61a21e980a7b9188424d04f1c265fdc5c21c7e85
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 01:34:21 2007 -0500
85xx start.S cleanup and exception support
From: Ed Swarthout <Ed.Swarthout@freescale.com>
Support external interrupts from platform to eliminate system hangs.
Define CONFIG_INTERRUPTS board configure option to enable.
Enable ecm, ddr, lbc, and pci/pcie error interrupts in PIC.
Remove extra cpu initialization redundant with hardware initialization.
Whitespace cleanup.
Define and use _START_OFFSET consistent with other processors using
ppc_asm.tmpl
Move additional code from .text to boot page to make room for
exception vectors at start of image.
Handle Machine Check, External and Critical exceptions.
Fix e500 machine check error determination in traps.c
TEXT_BASE can now be 0xfffc_0000 - which cuts binary image in half.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 7bd30fc4a6475b41d6679ae3aafc9fa505260c47
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Aug 14 01:33:18 2007 -0500
Add MPC8544DS README
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 40c7f9b0de4e300370adfc704128fa0f79a143b6
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:48 2007 -0500
85xx allow debugger to configure ddr.
Only check for mpc8548 rev 1 when compiled for 8548.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 29372ff38c5baab7d0e3a8c14fe11fa194a38704
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:47 2007 -0500
mpc85xx L2 cache reporting and SRAM relocation option.
Allow debugger to override flash cs0/cs1 settings to enable alternate
boot regions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 41f0f8fb1ab92f0cba7d329de90070f822f8299f
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:46 2007 -0500
e500 needs ppc_asm.tmp MCK_EXCEPTION
Always define MCK_EXCEPTION macro - so e500 can use it too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 53a5c424bf8655b7b4e2c305a441963259a26a81
Author: David Updegraff <dave@cray.com>
Date: Mon Jun 11 10:41:07 2007 -0500
multicast tftp: RFC2090
Implemented IETF RFC2090, Multicast TFTP. Initial implementation
on Realtek RTL8139 and Freescale TSEC.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit 5d110f0aa69f065ee386ec1840dfee1e8cc46bc1
Author: Wilson Callan <wcallan@savantav.com>
Date: Sat Jul 28 10:56:13 2007 -0400
New CONFIG_BOOTP_SERVERIP option
Added CONFIG_BOOTP_SERVERIP to allow the tftp server to be different
from the bootp server
Signed-off-by: Wilson Callan <wcallan@savantav.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit 50cca8b976ec74069860208c36e64ce8f4d5e4c1
Author: Mike Rapoport <mike@compulab.co.il>
Date: Sun Aug 12 08:48:27 2007 +0300
Add ability to take MAC address from the environment to DM9000 driver
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit be5d72d10d47609326226225181e301fb9a33b58
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Aug 13 21:57:53 2007 +0200
Minor coding style cleanup. Update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit cca34967cbd13ff6bd352be29e3f1cc88ab24c05
Author: Joe Hamman <joe.hamman@embeddedspecialties.com>
Date: Sat Aug 11 06:54:58 2007 -0500
Modify SBC8641D to use new Freescale PCI routines
PCI-Express sockets 1 and 2 verified working with Intel Pro/1000 PT
adapter.
Signed-off-by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signde-off-by: Jon Loeliger <jdl@freescale.com>
commit a08458303e7f9db67f296980036d3292c35cb45c
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Fri Jun 29 18:38:51 2007 +0200
atmel_mci: Fix data timeout value
Calculate the data timeout based on values from the CSD instead of
just using a hardcoded DTOR value. This is a backport of a similar fix
in BSP 2.0, with one additional fix: the DTOCYC value is rounded up
instead of down.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 0ba8eed28b575626b17e0a7882f923b83e0d7584
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Mon Aug 13 17:22:31 2007 +0200
AVR32: Include <div64.h> instead of <asm/div64.h>
include/asm-avr32/div64.h was recently moved to include/div64.h, but
cpu/at32ap/interrupts.c wasn't properly updated (an earlier version of
the patch was merged perhaps?)
This patch updates cpu/at32ap/interrupts.c so that the avr32 port
compiles again.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit f0d1246ed7cb5a88522244c596d7ae7e6f161283
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed Jun 27 13:34:26 2007 +0200
atmel_mci: Use 512 byte blocksize if possible
Instead of always using the largest blocksize the card supports, check
if it can support smaller block sizes and use 512 bytes if possible.
Most cards do support this, and other parts of u-boot seem to have
trouble with block sizes different from 512 bytes.
Also enable underrun/overrun protection.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
commit 273db7e1bdd1937e32f1d4507321bb721ebd3118
Author: Stefan Roese <sr@denx.de>
Date: Mon Aug 13 09:05:33 2007 +0200
ppc4xx: Fix problem in PLL clock calculation
This patch was originall provided by David Mitchell <dmitchell@amcc.com>
and fixes a bug in the PLL clock calculation.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9986bc3e40e899bea372a99a2bca4071bdf2e24b
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 21:34:50 2007 +0200
Update CHANGELOG
commit 77d19a8bf3b0b1e401cb9f23c81e2ef419705c1a
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 21:34:34 2007 +0200
Minor alignment of output, 2nd try.
Also update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 6b309f22a724fad8418e811751a0741b893419cf
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 20:35:49 2007 +0200
Minor alignment of output
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 6f6d7b9c8559e241e8d232621542b8b59699b07b
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 18:28:18 2007 +0200
Cleanup output on ADS5121 board
Signed-off-by: Wolfgang Denk
commit a4d2636f2a859245ed3a401f26189da2dfda4ceb
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 15:11:38 2007 +0200
Adapt board configuration and fix kernel crash on MCC200 board.
The update procedure was modified to turn off the USB subsystem
before exit for MCC200 and TRAB. This is necessary as otherwise the
USB controller continues to write periodically to system memory!
MCC200-specific notes:
- the patch disables the magic key check for MCC200
- the patch contains the configuration changes made
for the new revision of the board.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit e27f3a6efb9db5a533223b05c629ff4ac8d921bf
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 14:47:54 2007 +0200
Adjust default configuration of ADS5121 board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit afaac86fe2948ac84cd9a12bbed883b3c683e7d9
Author: Wolfgang Denk <wd@denx.de>
Date: Sun Aug 12 14:27:39 2007 +0200
Clean up some remaining CFG_CMD_ -> CONFIG_CMD_ issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5fe6be6208dda852c3564e384bd78d75784dea3e
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Tue Aug 7 21:14:22 2007 -0400
Improve error print messages.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 99dffca3b7590a16a00bc475c860b67b2a3f1462
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Jul 17 13:57:04 2007 -0500
fdt: allow for builds that don't want env and bd_t nodes
protect fdt_env and fdt_bd_t invocations, fix codingstyle while in the
area.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 91148bf7aeba142d6f348805db7625db7da64d6f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Jul 17 13:56:53 2007 -0500
fdt: do board setup based on fdt address specified on bootm line
The last fdt patch to bootm did board setup based on the address
specified by a prior fdt address command invocation. The bootm
code, as its call to fdt_chosen does, should use the fdt specified
by the user on the bootm command. Note this restores full
functionality for the 8360's existing default boot environment
values, e.g. 'run nfsboot' (i.e. no having to 'fdt addr $fdtaddr'
before booting a kernel).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit e125a2ffc209dd34794e326c7175658253beadf3
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Tue Jul 10 20:40:39 2007 -0400
Call ft_board_setup() from the bootm command.
In the patch titled "Create new fdt boardsetup command..." I removed the
call to ft_board_setup() from the routine fdt_chosen(), but I forgot
to add a direct call back into cmd_bootm.c
This fixes the oversight by adding the direct call to the bootm command.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit fd61e55dd8cb52ce3ff91b3917af26e24b6b0845
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Mon Jun 25 23:25:28 2007 -0400
Create new fdt boardsetup command, fix bug parsing [] form of set values.
Previously ft_board_setup() was called by fdt_chosen() which was not
really correctly structured. This splits ft_board_setup() out by creating
a new fdt boardsetup command.
Fix a bug when parsing fdt set command values which have the square
bracket form [00 11 22 33] - the length was updated incorrectly in when
parsing that form.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 6f35ded9e85493595e0eb66a82b502a95326d049
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Mon Jun 25 20:55:58 2007 -0400
Tighten up the error messages.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit c45874b05aae897a6c29d1a97d4bb708fca2756c
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Mon Jun 25 19:52:23 2007 -0400
Asthetic improvements: error messages and line lengths.
Tighten up the error messages, split overlength lines.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 35ec398f16e17df600edc1b38c1e9e62c15c9aa1
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Fri May 25 22:08:57 2007 -0400
Fix fdt_chosen() to call ft_board_setup(), clean up long lines.
The fdt_chosen() function was adding/seting some properties ad-hoc
improperly and duplicated (poorly) what was done in ft_board_setup()
Clean up long lines (setting properties, printing errors).
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 06e19a07701c968f15d72c083b5872a1a11c7b01
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Mon May 21 23:27:16 2007 -0400
For fdt_find_node_by_path(), handle the root path properly.
Also removes the special case root path detection in cmd_fdt.c since it
is no longer necessary.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 9675ee7208ab965d13ea8d8262d77ac4160ef549
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Thu May 17 23:54:36 2007 -0400
Add fdt_find_node_by_type() and fdt_find_compatible_node() to LIBFDT
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
commit 1a861169bc3758f9de3aead62b058736c6891246
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Wed Jun 6 22:47:58 2007 -0400
Replace fdt_node_offset() with fdt_find_node_by_path().
The new name matches more closely the kernel's name, which is also
a much better description.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
commit addd8ce83078c25f0eca5f23adbdfc64ca50a243
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Wed May 16 22:39:59 2007 -0400
Fix cmd_fdt line lengths, refactor code.
Break lines that were greater than 80 characters in length.
Move the fdt print and property parsing code to separate static functions
to reduce coding clutter in the fdt_cmd handling body.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 25114033ab21788810c48ba4df103b649da1223b
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat May 12 09:47:25 2007 -0400
FDT command improvements.
Fix "fdt set" so that it will create a non-existing property.
Add "fdt mknode" to create nodes.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 38eb508e8e811e2e57628f445de3a24a23c7d804
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat May 12 09:45:46 2007 -0400
Reorganize and fix problems (returns) in the bootm command.
Do *NOT* return after the "point of no return" has been passed.
If something goes wrong, the board must be reset after that point.
Move the "Transferring control to Linux" debug message back to where it
belongs: just before transferring control to linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 89c8757d8f213c47709bdc4efe0695263a6080a6
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Tue May 8 21:27:35 2007 -0400
Fix bugs in the CONFIG_OF_LIBFDT
Stupid coding mistakes (identified by Timur Tabi, thanks).
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 6be07cc1ca458278c85ecdbf1a0536cff4c701ec
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Wed Apr 25 22:47:15 2007 -0400
Improve fdt move length handling.
Make the length parameter optional: if not specified, do the move using
the current size unchanged.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit bb930e76fea6cf89ca2d98e2f7c7a6043d79327d
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Wed Apr 25 22:23:36 2007 -0400
Minor code clean up.
Declare the variable fdt properly as extern.
Call the "set_fn" function pointer the "short way" without the full
dereferencing syntax.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit ba24e2ac3bdb5c489f3c787e7542b6474c4d65c6
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Wed Apr 25 21:24:27 2007 -0400
Improve error messages, more informative.
Print more than the raw libfdt error message strings. This is especially
useful for cluing in the user when the bootm command aborts due to
blob problems.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 8096b3b8f772c1894ddeda9dbceff6a8826473a4
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Fri Apr 20 22:46:53 2007 -0400
libfdt: Conditionally compile based on CONFIG_OF_LIBFDT
This is the way u-boot reduces configured-out code. At Wolfgang
Grandegger and Wolfgang Denk's request, make libfdt conform.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
commit 923efd286411ed052d9e074f59f8986d6081061c
Author: Bruce Adler <bruce.adler@ccpu.com>
Date: Fri Aug 10 14:54:47 2007 -0700
add image size and descriptors for Spartan 3E FPGA chips
Spartan 3E image sizes taken from Table 1-4 in Xilinx UG332 (v1.1)
Signed-off by: Bruce Adler <bruce.adler@ccpu.com>
commit fb56579ffe7ef3275b7036bb7b924e5a0d32bd70
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Fri Aug 10 15:34:48 2007 -0500
make MAKEALL more immune to merge conflicts
..by placing board entries one per line, as suggested by jdl.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 2628114ec564f969f34b5f7105fbd168cb8c9c3f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Fri Aug 10 13:28:25 2007 -0500
README: Remove outdated cpu type, board type, and NAME_config lists
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 49bb59912d21aacb507eb81fd21fb7af650c706c
Author: Dave Liu <r63238@freescale.com>
Date: Fri Aug 10 15:48:59 2007 +0800
mpc83xx: Suppress the warning 'burstlen'
suppress the warning 'burstlen' of spd_sdram.
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit c646bba6465a45c60746d4cc1602cd06c1960f2d
Author: Joe Hamman <joe.hamman@embeddedspecialties.com>
Date: Thu Aug 9 15:11:03 2007 -0500
Add support for SBC8641D. Config files.
Add support for Wind River's SBC8641D reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>
commit 8ac273271d57321f90505c7a51cdb1ef2113b628
Author: Joe Hamman <joe.hamman@embeddedspecialties.com>
Date: Thu Aug 9 15:10:53 2007 -0500
Add support for SBC8641D. Board files.
Add support for Wind River's SBC8641D reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>
commit c2c0ab4aff86622b837a48a0e560351f9afafb95
Author: Stefan Roese <sr@denx.de>
Date: Fri Aug 10 20:34:58 2007 +0200
Conding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit c74b2108e31fe09bd1c5d291c3cf360510d4f13e
Author: Sergey Kubushyn <ksi@koi8.net>
Date: Fri Aug 10 20:26:18 2007 +0200
[ARM] TI DaVinci support, hopefully final
Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA
Changes:
- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
DV_EVM. Can't check if it works on SONATA, don't have a board any more,
but it at least compiles.
Here is an excerpt from session log on SCHMOOGIE...
U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17)
DRAM: 128 MB
NAND: 128 MiB
In: serial
Out: serial
Err: serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>
commit 2e4d94f1e3c2961428967a33b6ff2520568391b3
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:45 2007 -0500
fsl_pci_init cleanup.
Do not enable normal errors created during probe (master abort, perr,
and pcie Invalid Configuration access).
Add CONFIG_PCI_NOSCAN board option to prevent bus scan.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 936b3e69b667c3eb9a61ece4e78647d3fce9fc2a
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Fri Jul 27 01:50:44 2007 -0500
pciauto_setup_device bars_num fix
Passing bars_num=0 to pciauto_setup_device should assign no bars.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit cf0b185e58ca0aec8ae2b2a8804ec0ef58ee21d4
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Aug 6 17:39:44 2007 -0500
8641hpcn: Do correct sized pointer math.
When I rebased Ed's patch and cleaned up a few compilation
problems, I apparently rebased my brain on crack first.
Fix that by doing (char *) sized pointer math as needed.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit cfc7a7f5bb3273c9951173c788001d45118f141f
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Aug 2 14:42:20 2007 -0500
cpu/86xx fixes.
Remove rev 1 fixes.
Always set PICGCR_MODE.
Enable machine check and provide board config option
to set and handle SoC error interrupts.
Include MSSSR0 in error message.
Isolate a RAMBOOT bit of code with #ifdef CFG_RAMBOOT.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 35d22f957a85a22bb3cd1ad084fa5404620d1c42
Author: Stefan Roese <sr@denx.de>
Date: Fri Aug 10 10:42:25 2007 +0200
Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3a6d56c20989fe27360afe743bd2a7ad4d76e48f
Author: Dirk Behme <dirk.behme@googlemail.com>
Date: Thu Aug 2 17:42:08 2007 +0200
Make use of generic 64bit division in nand_util.c
Use generic 64bit division in nand_util.c. This makes nand_util.c
independent of any toolchain 64bit division.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
commit f7c086e94e8ce9aad7268af97f73aa6884686f27
Author: Dirk Behme <dirk.behme@googlemail.com>
Date: Thu Aug 2 17:41:14 2007 +0200
Move 64bit division from avr32 to generic lib
Move the 64bit division from lib_avr32 to lib_generic. With this, all
boards can do_div/__div64_32 if needed, not only avr one. Code is put
to lib_generic, so no larger memory footprint if not used. No code
modifications. Thanks for proposal by Håvard Skinnemoen.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
commit 157cda4d0c3d592ccbb19bbfc07d9251894f0894
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:31:22 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: HCU5 files
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 6e5de26c6e7580faf16e87745cd488b92b492d0c
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:30:33 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: HCU4 files
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit e8397fc78c9394d71de233a4d810fbc9047e4c76
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:38:26 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: common files
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit ac982ea5a4f2f993efcf52dca122f5a59df047d8
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:28:44 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: make related
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 137fdd9f474ecb853efdace5200576308c67f18d
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:28:03 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: HCU5 config
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 714bc55b35b6f6a65cc8740a3842a543e88cdef2
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:27:15 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: HCU4 config
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 1894dd381124bdbfbdae7cf3a6ca52a8eb1f4421
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:25:31 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: READMEs
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 641cca9569ce351ddb287fd3343d8b1dcb591db4
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Fri Jul 27 11:37:40 2007 +0200
Add PPC4xx-HCU4 and HCU5 boards: Infrastructure
This series of patches adds support for 2 boards from Netstal Maschinen.
The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.
The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.
The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.
This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
commit 3e4c90c6233618fc1806e63fde68df5f3d6a0171
Author: Stefan Roese <sr@denx.de>
Date: Fri Aug 10 08:42:55 2007 +0200
ppc4xx: Update lwmon5 POST configuration
Signed-off-by: Stefan Roese <sr@denx.de>
commit 29cb25da56afe18cf5e7072a92a9d98ea8af1fd4
Author: Yuri Tikhonov <yur@emcraft.com>
Date: Fri Aug 10 08:25:22 2007 +0200
POST: Add ppc4xx UART POST support without external uart clock (lwmon5)
The patch adds support for UART POST on ppc44x-based boards with no
external serial clocks installed.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
commit 99c2fdab91bc633e46fb41dbaa629f87ccf6e00f
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Mon Aug 6 18:18:34 2007 -0500
mpc83xx: fix ITX[GP] O=builddir builds
make: *** No rule to make target `/work/wd/tmp/board/mpc8349itx/u-boot.lds', needed by `/work/wd/tmp/u-boot'. Stop.
Both the ITX and ITX-GP fail when you use "make O=<some dir> ..." or
"BUILD_DIR=<some dir> ./MAKEALL ..."
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 47e8bc846759e037b8af0e5f9c9f9cfa7a1050c3
Author: Dave Liu <r63238@freescale.com>
Date: Wed Aug 1 15:00:59 2007 +0800
mpc83xx: Correct the README for DDR ECC
Update the README for DDR ECC, change the name
to README.mpc83xx.ddrecc.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit daab8c67d2defef73dc26ab07f0c3afd1b05d019
Author: Dave Liu <r63238@freescale.com>
Date: Wed Aug 1 15:00:15 2007 +0800
mpc83xx: Consolidate the ECC support of 83xx
Remove the duplicated source code of ecc command on the <board>.c,
for reused, move these code to cpu/mpc83xx directory.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 036575c544cf1b69654d8fb334bda69c6ff3da36
Author: Dave Liu <r63238@freescale.com>
Date: Sat Aug 4 13:37:39 2007 +0800
mpc83xx: Correct the burst length for DDR2 with 32 bits
The burst length should be 4 for DDR2 with 32 bits bus
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit 1c274c4e05b6dc9b24edc8aa618b02f607ee6eed
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Jul 25 19:25:33 2007 -0500
mpc83xx: add support for the MPC8323E RDB
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 343d91009d55fc5b3ff8cc940597af6c6aa1d359
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Jul 25 19:25:28 2007 -0500
mpc83xx: fixup generic pci for libfdt
add libfdt support to the generic 83xx pci code
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit f57ac7a7b37109245b69db80839ebee26179966a
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Jul 25 19:25:22 2007 -0500
mpc83xx: fix 8360 and cpu functions to update fdt being passed
..and not the global fdt. Rename local fdt vars to blob so as not to
be confused with the global var with the same three-letter name.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 8be404459a6b7395415a57bb35e8377e3b2b5acb
Author: Jerry Van Baren <gvb.uboot@gmail.com>
Date: Wed Jul 4 21:34:24 2007 -0400
mpc83xx: Fix errors when CONFIG_OF_LIBFDT is enabled
Several node strings were not correct (trailing slashes and properties
in the strings)
Added setting of the timebase-frequency.
Improved error messages and use debug() instead of printf().
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 26d02c9bbac1751c5e19294f000100b48d43a920
Author: Jerry Van Baren <gvb.uboot@gmail.com>
Date: Wed Jul 4 21:27:30 2007 -0400
mpc83xx: Replace fdt_node_offset() with fdt_find_node_by_path().
The new name matches more closely the kernel's name, which is also
a much better description.
These are the mpc83xx changes made necessary by the function name change.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 9be39a67c9f8fef7107f5df09d673005f04d0963
Author: Dave Liu <daveliu@freescale.com>
Date: Mon Jun 25 10:41:56 2007 +0800
mpc83xx: Add support for the display of reset status
83xx processor family has many reset sources, such as
power on reset, software hard reset, software soft reset,
JTAG, bus monitor, software watchdog, check stop reset,
external hard reset, external software reset.
sometimes, to figure out the fault of system, we need to
know the cause of reset early before the prompt of
u-boot present.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit ff9658d7049bf8c8e8e0a05dbe5e9f7e91aa5a5d
Author: Dave Liu <daveliu@freescale.com>
Date: Mon Jun 25 10:41:04 2007 +0800
mpc83xx: Fix the align bug of SDMA buffer
According to the latest user manual, the SDMA temporary
buffer base address must be 4KB aligned.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 66dc2c2dc51f8b88bb8e231bc80cd92eae1d6476
Author: Dave Liu <daveliu@freescale.com>
Date: Mon Jun 25 13:21:12 2007 +0800
mpc83xx: Revise the MPC8360EMDS readme doc
When the rev2.x silicon mount on the MPC8360EMDS baord,
and if you are using the u-boot version after the commit
3fc0bd159103b536e1c54c6f4457a09b3aba66ca.
to make the ethernet interface usable, we have to setup
the jumpers correctly.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit e739bc95797aac4fefc4c75b55c7c78e59d3ea9c
Author: Timur Tabi <timur@freescale.com>
Date: Tue Jul 3 13:46:32 2007 -0500
FSL I2C driver programs the two I2C busses differently
The i2c_init() function in fsl_i2c.c programs the two I2C busses differently.
The second I2C bus has its slave address programmed incorrectly and is
missing a 5-us delay.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit df33f6b4d6d63693dd9200808b242de1b86cb8e8
Author: Timur Tabi <timur@freescale.com>
Date: Tue Jul 3 13:04:34 2007 -0500
Update SCCR programming in cpu_init_f() to support all 83xx processors
Update the cpu_init_f() function in cpu/mpc83xx/cpu_init.c to program the
bitfields for all 83xx processors. The code to update some bitfields was
compiled only on some processors. Now, the bitfields are programmed as long
as the corresponding CFG_SCCR option is defined in the board header file.
This means that the board header file should not define any CFG_SCCR macros
for bitfields that don't exist on that processor, otherwise the SCCR will be
programmed incorrectly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 9546266999f0b9b51372636614211b88d90f0f25
Author: Martin Krause <martin.krause@tqs.de>
Date: Fri Jun 22 13:04:22 2007 +0200
TQM834x: cleanup configuraton
Remove irritating #undef DEBUG
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 5d497e6bf0f5bf63729b4a47b3fd786d3c77a1bc
Author: david.saada <David.Saada@ecitele.com>
Date: Mon Jun 18 09:09:53 2007 -0700
MPC83xx: Fix makefile to generate config.h file in the build directory
MPC83xx: Fix the Makefile config sections to generate the include/config.h
file in the build directory instead of the source directory.
Signed-off-by: David Saada <david.saada@ecitele.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 1ded0242e437259366792d52b7e9d1e1931d8fa5
Author: Lee Nipper <Lee.Nipper@freescale.com>
Date: Thu Jun 14 20:07:33 2007 -0500
mpc83xx: Add support for 8360 silicon revision 2.1
This change adds 8360 silicon revision 2.1 support to u-boot.
Signed-off-by: Lee Nipper <lee.nipper@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit a22806469a8f2b69c829f4fd5361fdebd0cb01b4
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Wed Aug 8 04:14:28 2007 -0500
Treat ppc64 host as ppc
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 0dc4279b08ff82472bec2e2c90858602459febe8
Author: Jason Jin <Jason.jin@freescale.com>
Date: Wed Aug 8 09:01:46 2007 +0800
Minor fix for bios emulator makefile
Add $(obj) to LIB avoiding objects be built in the source dir
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit ce981dc857adfc8036ca2f6d5d5a06c2a8aa77d6
Author: Jason Jin <Jason.jin@freescale.com>
Date: Wed Aug 8 08:33:11 2007 +0800
Add CONFIG_BIOSEMU define to guard all the bios emulator code
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
This patch fix the compile issue on the board that did not enable the bios emulator
commit ed8106433522f2ea8933e9808346860d061d7731
Author: Zach Sadecki <Zach.Sadecki@ripcode.com>
Date: Tue Jul 31 12:27:25 2007 -0500
tsec: fix multiple PHY support
The change entitled "Reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx"
broke multiple PHY support in tsec.c. This fixes it.
Signed-off-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit dcb84b7208ade0bbebbeb56bec9c2c64f8b2eede
Author: Joe Hamman <joe.hamman@embeddedspecialties.com>
Date: Thu Aug 9 09:08:18 2007 -0500
tsec: Allow Ten Bit Interface address to be configurable
Allow the address of the Ten Bit Interface (TBI) to be changed in the
event of a conflict with another device.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
commit 3ba4c2d68f6541db4677b4aea12071f56e6ff6e6
Author: Stefan Roese <sr@denx.de>
Date: Wed Aug 8 09:54:26 2007 +0200
Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit a41de1f0d373e09c782dea558385a06247111ba5
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 05:15:18 2007 -0500
Port enabled for I2C signals and chipselects port configuration.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 1a33ce65a4c51a69190dd8c408f9e1c62a66e94f
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 04:31:18 2007 -0500
Added NAND support
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit eaf9e447beb3e498818ef8ad0b8c1597cd506149
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 04:11:20 2007 -0500
Added I2C support
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 99c03c175d2689093176facf17c58ce2cb320001
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 03:58:52 2007 -0500
Changed CFG_CLK to gd->bus_clk for CFG_TIMER_PRESCALER. Added DECLARE_GLOBAL_DATA_PTR for time.c
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 8d1d66af54d305de29d0bbf4aa8c9e6375f7f731
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 03:55:21 2007 -0500
Added uart_gpio_conf() in serial_init(), seperated uart port configuration from cpu_init() to uart_gpio_conf()
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 6fde84a44b7e575ea80fe0e2d5be3b6f73d1e630
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 03:43:30 2007 -0500
Moved sync() from board file to include/asm-m68k/io.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 9e737d8476e7d6a596d16caaf6a3853a9a1190a2
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 03:30:44 2007 -0500
Declared attributes of void __mii_init(void) as an alias for int mii_init(void)
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 9998bd37ead85e93953559720710d3b0685c81e6
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Sun Aug 5 03:19:10 2007 -0500
Renamed CONFIG_MCFSERIAL to CONFIG_MCFUART
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 7c4c3722a38d40b0cf537ddae72b04f4088b190c
Author: Jason Jin <Jason.jin@freescale.com>
Date: Tue Aug 7 16:17:06 2007 +0800
Add CONFIG_BIOSEMU define to guard all the bios emulator code
This patch fix the compile issue on the board that did not enable the bios emulator
commit bf1060ea4f9eaa7e7d164a70a7d6f28939882053
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Aug 7 16:02:13 2007 +0200
Fix missing brace error in fs/fat/fat.c
[pointed out by Roderik Wildenburg]
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 706714d97a0d08d59eda4de2268c39f504688329
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Aug 6 23:41:53 2007 +0200
[FIX] remove cute code
commit f500d9fdeb576288656dac427052ad2c5ca0ad1a
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Aug 6 23:35:26 2007 +0200
[FIX] Fix romfs code
commit ab4b956d3143f8f8174089053f5dfabbb04762b0
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Aug 6 23:31:49 2007 +0200
[FIX] Coding style cleanup - Wolfgang's suggestions
commit 6c33c78557ca6f8da68c01ce33e278695197d3f4
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Aug 6 23:21:05 2007 +0200
Fixed typo in README (pointed out by Martin Jost).
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 537223afa61f64480df31ce440a9cb386df4a814
Author: Stefan Roese <sr@denx.de>
Date: Mon Aug 6 21:10:17 2007 +0200
ppc4xx: Update AMCC Bamboo README doc/README.bamboo
As suggested by Eugene O'Brien <Eugene.O'Brien@advantechamt.com>,
here an updated Bamboo README.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9c7e4b06214db61bb21f1bcbe57c97519669baae
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Aug 6 02:17:36 2007 +0200
Coding style cleanup. Update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 221838cc7eb178370ff62aa05920a582e12ac322
Author: Jason Jin <Jason.jin@freescale.com>
Date: Tue Jul 10 09:03:22 2007 +0800
Remove the bios emulator from MAI board.
The bios emulator in the MAI board can not pass compile
and have a lot of crap in it. remove it and will have a
clean and small bios emulator in the drivers directory
which can be uesed for every board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 5618332409bb96f4448d1712899369fc80c0b489
Author: Jason Jin <Jason.jin@freescale.com>
Date: Fri Jul 13 12:14:59 2007 +0800
Fix some compile issues for MAI board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 0f460a1ee148b648ee242c3157650287d4296260
Author: Jason Jin <Jason.jin@freescale.com>
Date: Fri Jul 13 12:14:58 2007 +0800
Configurations for ATI video card BIOS emulator
This patch add definition of the BIOS emulator and the ATI framebuffer
driver for MPC8641HPCN board.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit ece92f85053b8df613edcf05b26a416cbc3d629c
Author: Jason Jin <Jason.jin@freescale.com>
Date: Fri Jul 6 08:34:56 2007 +0800
This is a BIOS emulator, porting from SciTech for u-boot, mainly for
ATI video card BIOS. and can be used for x86 code emulation by some
modifications.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 5072188acabde3178fac7f5a597150e6e74fd40c
Author: Jason Jin <Jason.jin@freescale.com>
Date: Fri Jul 6 08:33:33 2007 +0800
This is a framebuffer driver for ATI video card, can work for PCI9200,
X300, X700, X800 ATI video cards.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 5728be389e65fd47f34b33c2596271eb4db751ae
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Aug 6 01:01:49 2007 +0200
Coding style cleanup. Update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 8092fef4c29b395958bb649647da7e3775731517
Author: Martin Krause <Martin.Krause@tqs.de>
Date: Tue Dec 12 14:26:01 2006 +0100
Add functions to list of exported functions
Additionally export the following fuctions (to make trab_config build again):
- simple_strtol()
- strcmp()
Also bump the ABI version to reflect this change
Signed-off-by: Martin Krause <martin.krause@tqs.de>
commit 63cec5814fab5d2b1c86982327433807a5ac0249
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Thu Aug 2 14:09:49 2007 -0500
Make MPC8641's PCI/PCI-E driver a common driver for many FSL parts.
All of the PCI/PCI-Express driver and initialization code that
was in the MPC8641HPCN port has now been moved into the common
drivers/fsl_pci_init.c. In a subsequent patch, this will be
utilized by the 85xx ports as well.
Common PCI-E IMMAP register blocks for FSL 85xx/86xx are added.
Also enable the second PCI-Express controller on 8641
by getting its BATS and CFG_ setup right.
Fixed a u16 vendor compiler warning in AHCI driver too.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a274ca4f6d68830e7c916f897561cff8c4101c38
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Aug 5 22:33:05 2007 +0200
[FIX] Coding style cleanup
commit af8377d4eb3a0ac5a831830d5ce63fbf65fecb7f
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Aug 5 16:13:31 2007 +0200
[FIX] Xilinx Uartlite driver
Because PPC405 can use UARTLITE serial interface and
Microblaze can use Uart16550 serial interface not only Uartlite.
commit 98889edd50aadf862071eb5664747ad0d568a20e
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Aug 5 15:54:53 2007 +0200
[FIX] Change configuration for XUPV2P Microblaze board
commit 537091b4eed9302865d03fef3f7212b4fe5cf28f
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Aug 5 15:53:50 2007 +0200
[PATCH] Added support for Xilinx Emac community driver
commit 86b116b1b1e165ca4840daefed36d2e3b8460173
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Fri Aug 3 12:08:16 2007 +0200
cm1_qp1 -> cm5200: single U-Boot image for modules from the cm5200 family.
Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on
Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit c7e717ebc2b044d7a71062552c9dc0f54ea9b779
Author: Andy Fleming <afleming@freescale.com>
Date: Fri Aug 3 04:05:25 2007 -0500
Add Marvell 1149 PHY support to the TSEC
commit b1b54e352028ed370c3aa95d6fdeb9d64c5d2f86
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 2 21:27:46 2007 +0200
Coding style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 63e22764d2f8653f68888c667eb65b3996b52680
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 2 10:11:18 2007 +0200
Minor cleanup of <board>_nand build rules.
commit 9ca8d79de096c65b9b9c867259b3ff4685f775ef
Author: Stefan Roese <sr@denx.de>
Date: Thu Aug 2 08:33:56 2007 +0200
ppc4xx: Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit c92409812206ac67a7fa7aae298539a9c3804a46
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Tue Jul 31 18:51:48 2007 +0200
[ppc440SPe] Graceful recovery from machine check during PCIe configuration
During config transactions on the PCIe bus an attempt to scan for a
non-existent device can lead to a machine check exception with certain
peripheral devices. In order to avoid crashing in such scenarios the
instrumented versions of the config cycle read routines are introduced, so
the exceptions fixups framework can gracefully recover.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
commit dec99558b9ea75a37940d07f41a3565a50b54ad1
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Tue Jul 31 18:19:54 2007 +0200
[ppc4xx] Separate settings for PCIe bus numbering on 440SPe rev.A
This brings back separate settings for PCIe bus numbers depending on chip
revision, which got eliminated in 2b393b0f0af8402ef43b25c1968bfd29714ddffa
commit. 440SPe rev. A does NOT work properly with the same settings as for
the rev. B (no devices are seen on the bus during enumeration).
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
commit cdd917a43da6fa7fc8f54a3cc9f420ce5ecf3197
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Aug 2 00:48:45 2007 +0200
Fix build errors and warnings / code cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit d2f68006627eda6cb6c7f364bddf621dbfd2fc68
Author: Eugene OBrien <eugene.obrien@advantechamt.com>
Date: Tue Jul 31 10:24:56 2007 +0200
ppc4xx: Update AMCC Bamboo 440EP support
Changed storage type of cfg_simulate_spd_eeprom to const
Changed storage type of gpio_tab to stack storage
(Cannot access global data declarations in .bss until afer code relocation)
Improved SDRAM tests to catch problems where data is not uniquely addressable
(e.g. incorrectly programmed SDRAM row or columns)
Added CONFIG_PROG_SDRAM_TLB to support Bamboo SIMM/DIMM modules
Fixed AM29LV320DT (OpCode Flash) sector map
Signed-off-by: Eugene OBrien <eugene.obrien@advantechamt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit ea9f6bce383cc9fbcdee28b5836109b1a6dba574
Author: Stefan Roese <sr@denx.de>
Date: Tue Jul 31 08:37:01 2007 +0200
ppc4xx: Update 440EPx lwmon5 board support
- Clear ECC status regs after ECC POST test
- Set dcbz for ECC generation with caches enabled as default
- Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 27a528fb41433c4c1e2b5d6bd3fd8d78606fc724
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 30 11:04:57 2007 +0200
ppc4xx: Only print ECC related info when the error bis are set
Signed-off-by: Stefan Roese <sr@denx.de>
commit e36220a4baf1f188ba60f17e9d0f043069b1362a
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Fri Jul 27 16:44:31 2007 +0200
new FPGA image for PLU405 board
new FPGA image for PLU405 board with improved CompactFlash timing
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit 8993e54b6f397973794f3d6f47d3b3c0c98dd4f6
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Fri Jul 27 14:43:59 2007 +0200
[ADS5121] Support for the ADS5121 board
The following MPC5121e subsystems are supported:
- low-level CPU init
- NOR Boot Flash (common CFI driver)
- DDR SDRAM
- FEC
- I2C
- Watchdog
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
commit 1863cfb7b100ba0ee3401799457a01dc058745f8
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Fri Jul 27 14:22:04 2007 +0200
[PPC] Remove unused MSR_USER definition
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
commit d4024bb72dd81695ec099b2199eda0d27c623e62
Author: John Otken <john@softadvances.com>
Date: Thu Jul 26 17:49:11 2007 +0200
ppc4xx: Add support for AMCC 405EP Taihu board
Signed-off-by: John Otken <john@softadvances.com>
commit b66091de6c7390620312c2501db23d8391e7cabb
Author: Anatolij Gustschin <agust@denx.de>
Date: Thu Jul 26 15:08:01 2007 +0200
ppc4xx: lwmon5: Update Lime initialization
Change Lime SDRAM initialization to now support 100MHz and
133MHz (if enabled). Also the framebuffer is initialized to
display a blue rectangle with a white border.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9f24a808f17fc0f37b7fb4805f734741335caecc
Author: Stefan Roese <sr@denx.de>
Date: Tue Jul 24 09:52:52 2007 +0200
ppc4xx: lwmon5: Support for 128 MByte NOR FLASH added
The used Intel NOR FLASH chips have internally two dies, and are now
treated as two seperate chips.
Signed-off-by: Stefan Roese <sr@denx.de>
commit aedf5bde179ecfbd0a96130d18996a96518b785f
Author: Stefan Roese <sr@denx.de>
Date: Tue Jul 24 07:20:09 2007 +0200
ppc4xx: Fix lwmon5 interrupt controller setup (polarity, trigger...)
As suggested by Hakan Eryigit, here an updated setup for the lwmon5
interrupt controller.
Signed-off-by: Stefan Roese <sr@denx.de>
commit a71d96eac8130b53a91f93cd10c70fca0db18d52
Author: Stefan Roese <sr@denx.de>
Date: Fri Jul 20 15:03:44 2007 +0200
ppc4xx: Fix bug with default GPIO output value
As spotted by Matthias Fuchs, the default output values for all GPIO1
outputs were not setup correctly. This patch fixes this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 531e3e8b831f357056448fa573137d5fb37000fd
Author: Pavel Kolesnikov <concord@emcraft.com>
Date: Fri Jul 20 15:03:03 2007 +0200
POST: Add ECC POST for the lwmon5 board
This patch adds ECC Post test for the Lwmon5 board based
on PPC440EPx to U-Boot.
Signed-off-by: Pavel Kolesnikov <concord@emcraft.com>
Acked-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
commit cc3023b9f95d7ac959a764471a65001062aecf41
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Thu Jul 19 17:12:28 2007 +0200
Fix breakage of 8xx boards from recent commit.
This patch fixes the negative consequences for 8xx of the recent
"ppc4xx: Clean up 440 exceptions handling" commit.
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
commit c883f6ea32dce91f07670b3aafecf6c99b1e5341
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 13:11:12 2007 +0200
Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 8848ec858f74ed6dab06fb6d5ddc933e0a1328bf
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 10:02:12 2007 +0200
ppc4xx: Code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2a49fc17d09020e7ebd9536694d99d20e419fcb8
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 10:01:38 2007 +0200
ppc4xx: AMCC Luan uses the new boardspecific DDR2 controller setup
Signed-off-by: Stefan Roese <sr@denx.de>
commit df3f17422aeb03fb81a7ac8c78d2b05d05aa4cf9
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 10:00:43 2007 +0200
ppc4xx: Support for Yucca board with 440SPe Rev A added to 44x_spd_ddr2.c
The new boardspecific DDR2 controller configuration is used for the Yucca
board. Now the Yucca board with 440SPe Rev. A chips is also supported.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6ed14addf97c8cd8f531e9ae7b2d3e222fffd53e
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 09:57:00 2007 +0200
ppc4xx: Add new weak functions to support boardspecific DDR2 configuration
The new "weak" functions ddr_wrdtr() and ddr_clktr() are added to better
support non default, boardspecific DDR(2) controller configuration.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5743a9207a370b90f09b20ebd61167c806b937f3
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 16 08:53:51 2007 +0200
ppc4xx: Add remove_tlb() function to remove a mem area from TLB setup
The new function remove_tlb() can be used to remove the TLB's used to
map a specific memory region. This is especially useful for the DDR(2)
setup routines which configure the SDRAM area temporarily as a cached
area (for speedup on auto-calibration and ECC generation) and later
need this area uncached for normal usage.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0c0a9cda1bde37106520476ed486bd67eb8d30ae
Author: Michal Simek <monstr@monstr.eu>
Date: Mon Jul 16 00:31:07 2007 +0200
[PATCH] Support for Xilinx EmacLite controller
commit 3a6cab844cf74f76639d795e0be8717e02c86af7
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Jul 14 22:51:02 2007 +0200
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5280f352c8da33b1d7fbf448768717d9e16ff9a1
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Jul 14 13:11:28 2007 +0200
[FIX] support for simply measuring time
commit 91bb4ca665d2e0cf7f60c4b5b370990250ec0c43
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Jul 14 12:41:23 2007 +0200
[FS] Added support for ROMFS
commit 011595307731a7a67a7445d107c279d031e8ab97
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Sat Jul 14 01:06:58 2007 +0200
[PCS440EP] - fix compile error, if BUILD_DIR is used
commit 5a2f1098d81ad58b309e5e558d0492643166a799
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Jul 14 00:18:48 2007 +0200
[PATCH] Support time without timer
commit a476ca2ac2217ddd05a2bf0c514075814b10a3c0
Author: Michal Simek <monstr@monstr.eu>
Date: Fri Jul 13 21:43:55 2007 +0200
[PATCH] Remove problem with disabled BARREL SHIFTER
commit 55e26ad62107d2f14f757de3ae0b14b9aa7aed94
Author: Michal Simek <monstr@monstr.eu>
Date: Fri Jul 13 21:41:44 2007 +0200
[FIX] correct help for rspr
commit fad63407154f46246ce80d53a9c669a44362ac67
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Jul 13 09:54:17 2007 +0200
make show_boot_progress () weak.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 907902472391b6ca1876ec300687562ecaf459b1
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Jul 13 08:26:05 2007 +0200
[PCS440EP] - The DIAG LEDs are now blinking, if an error occur
- fix compile error, if BUILD_DIR is used
Signed-off-by: Heiko Schocher <hs@denx.de>
commit a2e1c7098cf9574386b0c96841dfc8ea5cc93578
Author: Stefan Roese <sr@denx.de>
Date: Thu Jul 12 16:32:08 2007 +0200
ppc4xx: Change receive buffer handling in the 4xx emac driver
This change fixes a bug in the receive buffer handling, that
could lead to problems upon high network traffic (broadcasts...).
Signed-off-by: Stefan Roese <sr@denx.de>
commit 239f05ee4dd4cfe0b50f251b533dcebe9e67c360
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Jul 12 01:45:34 2007 +0200
Update CHANGELOG, minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5a56af3b522ba47fb33a3fee84d23bf1e5429654
Author: Andy Fleming <afleming@freescale.com>
Date: Fri Jun 8 16:41:18 2007 -0500
Remove erroneous errata code from Marvel 88E1111S driver
The Marvel 88E1111S driver for the TSEC was copied from the
88E1101 driver, and included a fix for an erratum which does not
exist on that part. Now it is removed
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 982efcf23fd03647e01e2fbe28a7a36239156cc0
Author: Andy Fleming <afleming@freescale.com>
Date: Tue Jun 5 16:38:44 2007 -0500
From: eran liberty <eran.liberty@gmail.com>
adds the reset register to 85xx immap
Signed-off-by: Eran Liberty <eran.liberty@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit d3ec0d943a045bdb99e159e7bbc77430e09f11d7
Author: Andy Fleming <afleming@freescale.com>
Date: Thu May 10 17:50:01 2007 -0500
Polished the 85xx ADS config files
Made the boot commands use device trees by default.
Also moved the ramdisk to 1000000 (I think the previous address
was getting overridden during boot).
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit bfb37b32d1b0b03f18077dba49cc66a6e76fa038
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed May 9 11:03:32 2007 -0500
8544ds: Fix Makefile after moving pixis to board/freescale.
The OBJTREE != SRCTREE build scenario was broken.
This fixes it.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2a3cee43c3b71fa5b8d91db19f05067865290f3e
Author: Andy Fleming <afleming@freescale.com>
Date: Wed May 9 00:54:20 2007 -0500
tsec: Fix PHY code to match first driver
Jarrold Wen noticed that the generic PHY code always matches
under the current implementation. Change it so the first match
wins, and *only* unknown PHYs trigger the generic driver
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit ccc091aac61a38cd998d575d92f7232e256d6312
Author: Andy Fleming <afleming@freescale.com>
Date: Tue May 8 17:27:43 2007 -0500
Add support for CPM device tree configuration to 8560 ADS
* Adds code to modify CPM frequencies
* Cleans up the config file to #define TSEC and (for now) #undef FCC
* Adds the MII command for all 8560 ADS configurations
* Updates config file to provide convenience commands for booting
with a device tree
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 7507d56ccaf7aae1c474342a9a5540165cd7e9d9
Author: Andy Fleming <afleming@freescale.com>
Date: Tue May 8 17:23:02 2007 -0500
Fix Marvell 88e1145 PHY init code
Fix a bug in the Marvell 88e1145 PHY init code in the TSEC driver
where the reset was being done after the errata code instead of
before.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 5dc210dec5bace98a50b6ba905347890091a9bb0
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Jul 11 14:52:16 2007 -0500
Add simple agent/end-point configuration in PCI AutoConfig for PCI_CLASS_PROCESSOR_POWERPC.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit e8b85f3ba4cd8930e0a2fea2100c815d64201765
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Jul 11 14:52:08 2007 -0500
pciauto setup bridge
The P2P bridge bus numbers programmed into the device are relative to
hose->first_busno.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 571f49fa717004ca4268b4e24057efc7bf9f987b
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Jul 11 14:52:01 2007 -0500
Support PCIe extended config registers
FSL PCIe block has extended cfg registers in the 100 and 400 range.
For example, to read the LTSSM register: pci display <busn>.0 404 1
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit ba5feb12581bb2912ce301e4866b71f846e9fc07
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Jul 11 14:51:48 2007 -0500
Minor improvements to drivers/pci_auto.c
- Make pciauto_{pre,post}scan_setup_bridge non-static
- Added physical address display in debug messages.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 40e81addab7bb74d20ddf681ce9babc880a828ee
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Jul 11 14:51:35 2007 -0500
Start pci hose scan from hose->current_busno.
Ensure hose->current_busno is not less than first_busno. This fixes
broken board code which leaves current_busno=0 when first_busno is
greater than 0 for the cases with multiple controllers.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 3865b1fb7843a08ad49a6319a36415752276ff48
Author: Stefan Roese <sr@denx.de>
Date: Wed Jul 11 12:13:53 2007 +0200
Fix some compile problems introduced by the latest CFG_CMD_xxx cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit fa1df308926a6f70e3504c57514ef27ac31fd13a
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Jul 11 20:11:07 2007 +0200
CM1.QP1: Support for the Schindler CM1.QP1 board.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit 96e1d75be8193ca79e4215a368bf9d7f2362450f
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Wed Jul 11 18:39:11 2007 +0200
[PCS440EP] - Show on the DIAG LEDs, if the SHA1 check failed
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is used
Signed-off-by: Heiko Schocher <hs@denx.de>
commit e9514751cfa5cce61ea699fa0d3eb37898a5eeb5
Author: Stefan Roese <sr@denx.de>
Date: Sun Jul 8 13:44:27 2007 +0200
Fix malloc problem introduced with the relocation fixup for the PPC platform
The relocation fixup didn't handle the malloc pointer initialization
correctly. This patch fixes this problem. Tested successfully on 4xx.
The relocation fixup patches for 4xx will follow soon.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0dca874db62718e41253659e60f3a1de7eb418ce
Author: TsiChung <tcliew@Goku.(none)>
Date: Tue Jul 10 15:45:43 2007 -0500
Cache update and added CFG_UNIFY_CACHE
Enabled cache in cpu_init_f() for faster flash to mem allocation. Updated cache handling in start.S. Applied cache invalidate in fec_send() and fec_recv(). Added CFG_UNIFY_CACHE for CF V3 only.
Signed-off-by: TsiChung <tcliew@Goku.(none)>
commit 52b017604a8f4d4a795880ef6e7861d7f2f1b005
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:36:16 2007 -0500
Update header file. Include dtimer_intr_setup(). Changed timer divider to global define.
Include immap.h and timer.h. Moved dtimer interrupt setup to dtimer_intr_setup() from cpu/mcf532x/interrupts.c. Changed (CFG_CLK /1000000) -1 << 8 to CFG_TIMER_PRESCALER
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 5cdc07c7ef8f08ea55d3c47ed9221d91aa6d5fac
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:31:25 2007 -0500
Update header files
Include immap.h and renamed mcfrtc.h to rtc.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 2870e98ac8e5553e9187b12a47e5f46babb53990
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:29:21 2007 -0500
Add mcffec_initialize()
Added mcffec_initialize() in eth_initialize()
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 45a25bfd0c52f8a3fa137216bc94d32f90bedc5d
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:27:40 2007 -0500
Update header file and clean up
Include immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 0cee9c66318602c856a899ae5fa7579ccba6443a
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:23:15 2007 -0500
New uart structure and defines
Seperated from mcfuart.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit a90e79de8d99e9c9d69d60bfff9f24c337165900
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:22:31 2007 -0500
New timer structure and defines
Seperated from mcftimer.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit e04acb2eba4782489417240eff76e20e176aec10
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:21:09 2007 -0500
Rename mcfrtc to rtc
Since it is already in m68k folder, un-necessary to pad mcf. Replaced immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 2bd806fe4fc23958b8f78778199e7a6e3f8f6ad5
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:17:36 2007 -0500
Rename mcfserial.c. Update include header
Renamed mcfserial.c to mcfuart.c. Modified Makefile for mcfuart.o from mcfserial.o. Replace immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit f2208fbc2eb9de3f4285bfaa021c6ebae16c9b0e
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:13:58 2007 -0500
Header file update, clean up and cache handling
Replaced immap_5329.h and m5329.h with immap.h. Included cache_invalid.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 2e3f25ae9082daa9f5d181db45dfbc2e52ce0f97
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:10:40 2007 -0500
Create interrupts.c and modify Makefile
interrupt_init() and dtimer_intr_setup() are placed in interrupts.c. Added interrupts.o to Makefile
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit ddd104f1ed655eda50c06ba636237a83ed943f34
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:06:55 2007 -0500
Enable Icache
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit b9bf3de377b2bae70c983c9b97feae914999e735
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:05:31 2007 -0500
Update header file and some clean up
Replaced immap_5329.h and m5329.h with immap.h. Removed whitespaces.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 84a015b52ec820a5ae173717d78516de731c89c2
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:03:28 2007 -0500
Update header file and enable icache
Replaced immap_5329.h and m5329.h with immap.h. Enabled icache_enable() in cpu_init_r().
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 7a17e759c7a8b58e910daf54df611e94fc8ca074
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 23:01:22 2007 -0500
Update header file and removed interrupt_init()
Replace immap_5329.h and m5329.h with immap.h. Removed interrupt_init() and placed it in interrupts.c
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 3b635492c95bd0d6e08f93f699821cba1f602a64
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:57:46 2007 -0500
Update for flash.o and mii.o
Removed flash.o and added mii.o
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit c5ded275d839e4ff79f41718d50a835d989f57bc
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:56:19 2007 -0500
MII functions calls.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 427c814104560e29bda14955c67703245aaaa5b4
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:54:42 2007 -0500
Removed MII functions and replaced immap_5329.h and m5329.h with immap.h.
The removed MII routines will be placed in mii.c.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 01a793fda09c63df5a496f09dc1c7cb26e6751a2
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:51:05 2007 -0500
Duplicate code
There is a Common Flash Interface Driver existed. To use the CFI driver, define CFG_FLASH_CFI in configuration file.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 2744354a8437b8f78db178e30660215688bff570
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:46:38 2007 -0500
Seperate old structure defines and new structure defines
Removed new uart structure and defines to uart.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 2bd58608dbcff8890ca9a0c59e861ac24f8bb230
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:45:01 2007 -0500
Seperate old structure defines and new structure defines
New timer structure and defines will move to new timer.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 8cd5cd6de4ff92e03978338ed7aeb3ce7b7b9784
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:42:23 2007 -0500
Clean up
Removed whitespace
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 514871f565dd8bd1121e4a3ac1665a790e20b8f2
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:41:24 2007 -0500
Clean up
Replaced whitespace with tabs
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit 48dbfeabc7afffe30609a4489f10c22cb67ef7dd
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:39:07 2007 -0500
Create new header file and move peripherals base address from configs file to new header file.
Create new header file to include immap_5xxx.h and m5xxx.h and to share among drivers without update in driver file each processor is added. Moved peripherals base address and defines from configs file to immap.h.
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit be296e31c4411f96d9cb3d2afc8fcb006867abfa
Author: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Date: Thu Jul 5 22:24:58 2007 -0500
Revert file mode
Changed MAKEALL file mode to executable, removed executable file mode from Makefile
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
commit b3aff0cb9ecf236d7e8c93761dd1dadf6837a582
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 11:19:50 2007 -0500
disk/ doc/ lib_*/ and tools/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ddb5d86f0215bcb6c293510c50eb050e92883b7a
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 11:13:21 2007 -0500
drivers/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f40a7f3e3888b42a43674b099e5470022c8c544c
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 11:07:56 2007 -0500
fs/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 610f2e9c28a9c101e09fa1b78143cf5f00ed1593
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 11:05:02 2007 -0500
net/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 902531788376046da212afd1661cffb62f3daa1c
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 11:02:44 2007 -0500
common/: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d39b57415838c73fb0a37eca84de3c68ba990586
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 10:48:22 2007 -0500
board/[j-z]*: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 77a318545d57aefa844752465b94c7e09a3f26d0
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 10:39:10 2007 -0500
board/[A-Za-i]*: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 068b60a0eb7e73b243ca55399f2a7df76e2c3f3d
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 10:27:39 2007 -0500
cpu/ rtc/ include/: Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 079a136c3588814784561d6e4856970ee82d6e2a
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 10:12:10 2007 -0500
include/configs/[p-z]* + misc: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 7f5c01577400c74cc5bac74f41dd0d3c79df623c
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 09:38:02 2007 -0500
include/configs/[g-o]*: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 80ff4f99b84b64edca3fd10da365ec1493be1c95
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 09:29:01 2007 -0500
include/configs/[a-e]*: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a1aa0bb502e25fd598b5e0ccdfb2c174921d714a
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 09:22:23 2007 -0500
include/configs/[P-Z]*: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 659e2f6736232a08acca8785c206e2b4d9cd07d7
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 09:10:49 2007 -0500
include/configs/[J-O]*: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 11799434c5ff15a612577bb1ad1f4ea1a0595e4b
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Jul 10 09:02:57 2007 -0500
include/configs/[A-I]*: Cleanup BOOTP and lingering CFG_CMD_*.
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1fe80d79c5c4e52d3410a7ab4b8515da095cdab3
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 22:08:34 2007 -0500
Finally retire cmd_confdefs.h and CONFIG_BOOTP_MASK!
All of the choices for CONFIG_BOOTP_ are now documented in
the README file. You must now individually select exactly
the set that you want using a series of
#define CONFIG_BOOTP_<x>
statements in the board port config files now.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d3b8c1a743dcd31625c99e6a44590f207eb00028
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:57:31 2007 -0500
include/configs/[m-z]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2fd90ce575b02d189cbf443c85309bcd001aa393
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:48:26 2007 -0500
include/configs/[a-m]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 37d4bb70586659dedef1658ce1bed071be098aec
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:38:02 2007 -0500
include/configs/[T-Z]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 18225e8dd1950bd6dbf35011e436db7f474c187d
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:31:24 2007 -0500
include/configs/[P-S]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 7be044e4ea644b0ef1c486dadc1a4c2665b4374d
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:24:19 2007 -0500
include/configs/[H-N]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 5d2ebe1b3ef0055c661bb1a0d252bf252380069f
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 21:16:53 2007 -0500
include/configs/[A-G]*: Directly use CONFIG_BOOTP_* symbols rather than CONFIG_BOOTP_MASK.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f55f7f8d83f36021ab1f0e3d738f5d8c8083a7e3
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 19:12:30 2007 -0500
Retire CONFIG_COMMANDS finally.
Strip old CFG_CMD_* symbols out.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b5501f7d720fed99ab0b42c83f5dea52868ce007
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 19:10:03 2007 -0500
Update README.* to reference new CONFIG_CMD_* names now.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4431283c7e6d54ae180d466e51bf2d97471a0ad9
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 19:06:00 2007 -0500
cpu/m*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 3a1ed1e1f922c419bb71f7df4949d783ade369fa
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:57:22 2007 -0500
cpu/[7a-ln-z]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ab3abcbabd840928fb1eb5122118ca466b5e5013
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:45:16 2007 -0500
board/[q-z]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 3fe00109a5f12de55b6e25b1f98dfc24bc9090c9
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:38:39 2007 -0500
board/[m-p]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit c508a4cefd8a953fc64957650506a035e6e3d9d1
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:31:28 2007 -0500
board/[f-l]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b9307262f8a9f3b5c9e15a6067eadc17407146f6
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:24:55 2007 -0500
board/[d-e]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit fcec2eb93e126400009729328e797f12bc94f1fd
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:19:09 2007 -0500
board/[A-Za-c]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a593814f2be0c9cdc3133cd550b167b8a988328f
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:10:50 2007 -0500
rtc/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 67350568f9d46e66c21829f3513b3db0caeb948b
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:05:38 2007 -0500
lib_{arm,avr32,blackfin,generic,i386}/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 7def6b34f910f08d7ef0a14646da067719237ca2
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 18:02:11 2007 -0500
lib_{m68k,microblaze,mips,ppc}/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit dd60d1223b99a88a7216f3e041fe40634ad4c2bb
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:56:50 2007 -0500
fs/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit c91898bbc505aff3e12a807af88e76da18efb7ee
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:46:09 2007 -0500
tools/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 643d1ab23960950b52e0a2803c2d3ea4c558fa01
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:45:14 2007 -0500
net/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit cb51c0bf88f95a1bca68324b0126f8eed8b43273
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:39:42 2007 -0500
drivers/[n-z]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 07d38a17e964aec4c7827f0ee9a583bc8cc1ad6b
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:30:01 2007 -0500
drivers/[a-m]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit cde5c64d17cf4834aa7b5c373f288bc7dad27b29
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:22:37 2007 -0500
disk/: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 639221c76c88215bd55af83ad174fc30d1940f8f
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Jul 9 17:15:49 2007 -0500
include/: Remove obsolete references to CONFIG_COMMANDS
Mostly removed from comments here.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4ef218f6fdf8d747f4589da5252b004e7d2c2876
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Jul 10 00:01:28 2007 +0200
Coding style cleanup; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit c8603cfbd4573379a6076c9c208545ba2bbf019a
Author: Stefan Roese <sr@denx.de>
Date: Mon Jul 9 11:00:24 2007 +0200
Small coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0f92c7e7c9a62755b1457d3c46f93c8c1f6c19fc
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Mon Jul 9 10:10:08 2007 +0200
Migrate esd 405EP boards to new NAND subsystem
Remove unused CFG_NAND_LEGACY define
These boards to not have NAND.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit bd84ee4c2020c3a6861f4bb2e7ea0fb49f82e803
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Mon Jul 9 10:10:06 2007 +0200
Migrate esd 405EP boards to new NAND subsystem
Migrate esd 405EP boards to new NAND subsystem
-cleanup
-use correct io accessors (in/out_be32())
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit e09f7ab5749c345f924da272bea0521a73af5b11
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Mon Jul 9 10:10:04 2007 +0200
Migrate esd 405EP boards to new NAND subsystem
This patch prepares the migration from the legacy NAND driver
to U-Boot's new NAND subsystem for esd boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit c3517f919d0f61650cf3027fd4faf0f631142f6c
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 18:10:08 2007 -0500
common/* non-cmd*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit fd9bcaa35be64fe41a4223fdb6ecdbad52470b39
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 18:05:39 2007 -0500
common/cmd_[p-x]*: Remove obsolete references to CONFIG_COMMANDS.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit c76fe47425afc7d5d670ff0539823c85d65d9c42
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 18:02:23 2007 -0500
common/cmd_[i-n]*: Remove obsolete references to CONFIG_COMMANDS.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit baa26db4113679b80970ff447d91cc10217742a6
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 17:51:39 2007 -0500
common/cmd_[af]*: Remove obsolete references to CONFIG_COMMANDS.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit af075ee96e52dda7b6bca6c937588aeaaec5f2cd
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 17:02:01 2007 -0500
Clear up confusion over the CMD_POST and POST_DIAG mess.
For some reason, CONFIG_POST permeated as CONFIG_CMD_POST_DIAG
when it really means just CONFIG_CMD_DIAG. There is no CMD_POST.
Clear this mess up some.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b3631487105a57ab7cbadfc26efbaf9676275018
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 15:45:08 2007 -0500
Remove references to the old cmd_confdefs.h include file.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a22d4da95e20049b4daa1c2a022f61e8a72f2fb6
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 15:42:59 2007 -0500
include/configs: Catch some CONFIG_CMD_* conversion stragglers.
Use new CONFIG_CMD_* in lwmon5.h board config file.
Fix CONFIG_CMD_* typo braindamage in omap1510inn.h
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a5562901661bd428f7e5feb333f796372cb81019
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 15:31:57 2007 -0500
include/configs: Use new CONFIG_CMD_* in various [TUVWZYZ]* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit fe7f782d5b8c64a0195c68c31a0a11d4f641355e
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 15:02:44 2007 -0500
include/configs: Use new CONFIG_CMD_* in various S* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit e9a0f8f15c11f337967aa0600ad6e8af33037f50
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 15:12:40 2007 -0500
include/configs: Use new CONFIG_CMD_* in various R* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 12aa9fd23d724bd6ab88e1baa0db35133a27303f
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 14:55:07 2007 -0500
include/configs: Use new CONFIG_CMD_* in various Q* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit acf0269779422f3e147d2ddfb499c9f6ff10ad5e
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 14:49:44 2007 -0500
include/configs: Use new CONFIG_CMD_* in various P* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit e18a1061a8630cb67995fdf99afd3fb50d1b187d
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 14:21:43 2007 -0500
include/configs: Use new CONFIG_CMD_* in various [NO]* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 8353e139bfad9059c54f5b2421f1a3090e15a2e2
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 14:14:17 2007 -0500
include/configs: Use new CONFIG_CMD_* in various M* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 348f258f24253433e4a2302a0bbceb6740a67246
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 13:46:18 2007 -0500
include/configs: Use new CONFIG_CMD_* in various [IJKL]* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 6c4f4da9bfc9f9403f54fce678ed0364b7c86a6a
Author: Jon Loeliger <jdl@freescale.com>
Date: Sun Jul 8 10:09:35 2007 -0500
include/configs: Use new CONFIG_CMD_* in various H* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 60a0876b5106b34220e459c208bbf648073306c0
Author: Jon Loeliger <jdl@freescale.com>
Date: Sat Jul 7 21:04:26 2007 -0500
include/configs: Use new CONFIG_CMD_* in various F* and G* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit dcaa71562826a2466e894c868d132509dcda8444
Author: Jon Loeliger <jdl@freescale.com>
Date: Sat Jul 7 20:56:05 2007 -0500
include/configs: Use new CONFIG_CMD_* in various E* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 3c3227f3c737502311b25b72084573901cbbf17d
Author: Jon Loeliger <jdl@freescale.com>
Date: Sat Jul 7 20:40:43 2007 -0500
include/configs: Use new CONFIG_CMD_* in various D* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 49cf7e8ee7ef943fdfe866ce28410b0bfbf6a26c
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Jul 5 19:52:35 2007 -0500
include/configs: Use new CONFIG_CMD_* in various C* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit de8b2a6e33298dcdb10bdda48db25e53c3089eba
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Jul 5 19:32:07 2007 -0500
include/configs: Use new CONFIG_CMD_* in various B* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 498ff9a228485bd4b9f23d066bada268f9add1dd
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Jul 5 19:13:52 2007 -0500
include/configs: Use new CONFIG_CMD_* in various A* named board config files.
Since ADS860.h includes "board/fads/fads.h" with ramifications
on the CONFIG_COMMAND treatment, it too has to be adjusted to
exclude already configured commands in this same commit.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 10e038932f22ee80ebd53de312531e70e6590a2f
Author: Thomas Knobloch <knobloch@siemens.com>
Date: Fri Jul 6 14:58:39 2007 +0200
[NAND] Bad block skipping for command nboot
The old implementation of command nboot does not support reading the image from
NAND flash with skipping of bad blocks. The patch implements a new version of
the nboot command: by calling nboot.jffs2 from the u-boot command line the
command will load the image from NAND flash with respect to bad blocks (by using
nand_read_opts()). This is similar to e.g. the NAND read command: "nand
read.jffs2 ...".
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 334043f601a90ac53e5ecc846fbb73a1ef38cb1f
Author: Stefan Roese <sr@denx.de>
Date: Fri Jul 6 12:26:51 2007 +0200
ppc4xx: Update lwmon5 default environment
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5d187430a055d62f17ca84d75e7245439d1f7e75
Author: Stefan Roese <sr@denx.de>
Date: Fri Jul 6 11:48:24 2007 +0200
ppc4xx: Update lwmon5 board
Add unlock=yes environment variable to default variables to unlock
the CFI flash by default.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6b0a174a1e6f55e1f5a1fbb223cdad7645a4646e
Author: Stefan Roese <sr@denx.de>
Date: Fri Jul 6 09:45:47 2007 +0200
Fix problem with get/setdcr commands introduced by cfg patches
Signed-off-by: Stefan Roese <sr@denx.de>
commit f1152f8c28db4a22087c21c618a3f7baa48e9a4f
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Jul 6 02:50:19 2007 +0200
Code cleanup and default config update for STC GP3 SSA board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit e4dbe1b215f5c6c462e76909d240bd96472b84de
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Jul 5 17:56:27 2007 +0200
Fixing some typos etc. introduced mainly by cfg patches.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit b6b4684546809f89c8bac72863ca49b5fd8ac0cd
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Jul 5 11:12:16 2007 +0200
Minor coding style cleanup. Update CHANGELOG.
commit dca3b3d6d6396b67e5e84af53452164923c73443
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:46 2007 -0500
include/configs: Use new CONFIG_CMD_* in various [v-z]* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 6c18eb9804b525f3e4f3bb3d014dd69a200d9fa7
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:38 2007 -0500
include/configs: Use new CONFIG_CMD_* in various t* and u* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 46da1e96b7db14f4fcd2c92544e7c0862024bc76
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:30 2007 -0500
include/configs: Use new CONFIG_CMD_* in various s* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 90cc3eb6d2be856d9ddd81436de9cf343bc6b5c8
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:23 2007 -0500
include/configs: Use new CONFIG_CMD_* in various q* and r* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 26a34560d56a9df5bc2ae23525d9229736134757
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:17 2007 -0500
include/configs: Use new CONFIG_CMD_* in various p* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a5cb23092a7d31490a33d4ec871468b63babfa3c
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:13 2007 -0500
include/configs: Use new CONFIG_CMD_* in various o* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 929a2bfd142737003a8fc32e1b86e1f2c1850257
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:07 2007 -0500
include/configs: Use new CONFIG_CMD_* in various n* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 5dc11a511960d490f7f01ffd746edfe6277f99b0
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:33:01 2007 -0500
include/configs: Use new CONFIG_CMD_* in various m* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 9bbb1c0820c1fbd3811ab6ee4ba0f6c6f76b27e4
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:57 2007 -0500
include/configs: Use new CONFIG_CMD_* in various l* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit bc234c129fa04fb9fa33530930e5cbc6084cd47a
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:51 2007 -0500
include/configs: Use new CONFIG_CMD_* in various j* and k* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1d2c6bc491969f8d8fb34c8e30e8bea7a2af9c31
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:32 2007 -0500
include/configs: Use new CONFIG_CMD_* in various i* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 48d5d102a2f2e619c92050b9aedbb69689185bc0
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:25 2007 -0500
include/configs: Use new CONFIG_CMD_* in various h* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 72eb0efaed7048afcc61fc6f0085c49394b5dc36
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:19 2007 -0500
include/configs: Use new CONFIG_CMD_* in various g* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1bec3d3002d3bbbae6f2468a0f7376db1120d33e
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:10 2007 -0500
include/configs: Use new CONFIG_CMD_* in various e* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ab999ba1b31ebe78dd16374394a55d7c6e5aa6e4
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:32:03 2007 -0500
include/configs: Use new CONFIG_CMD_* in various d* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 37e4f24b87fa255ae456d193b7cd23c18dd1d56b
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:56 2007 -0500
include/configs: Use new CONFIG_CMD_* in various c* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ba2351f9d1e841bd00ea6dad1e3c16d0259ad264
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:49 2007 -0500
include/configs: Use new CONFIG_CMD_* in various b* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 0b361c916617aff79e647b40f0e43361e0bbaccf
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:42 2007 -0500
include/configs: Use new CONFIG_CMD_* in various a* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b730cda82e362df6a22f4c59c0a9b97e885b1014
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:35 2007 -0500
include/configs: Use new CONFIG_CMD_* in mpc5xx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d794cfefead5fc177cf4f41164e80382e9c9484a
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:15 2007 -0500
include/configs: Use new CONFIG_CMD_* in various 5200 board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ef0df52ab49eea4a30c15087fd27d54c1d946f2c
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:31:07 2007 -0500
include/configs: Use new CONFIG_CMD_* in STx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 866e3089bfc826bb4dc74637f8aad87a3bab79fc
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:30:58 2007 -0500
include/configs: Use new CONFIG_CMD_* in sbc* board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2694690e285acaa34922f55f4b5ae030da60c55a
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:30:50 2007 -0500
include/configs: Use new CONFIG_CMD_* in TQM board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1cc4c458329765b58e584a19821e796b3c10e976
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:30:28 2007 -0500
include/configs: Use new CONFIG_CMD_* in 82xx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 8ea5499afdaba0acf60923dd99001c399d4a7c8e
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jul 4 22:30:06 2007 -0500
include/configs: Use new CONFIG_CMD_* in 83xx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b44896215a09c60fa40cae906f7ed207bbc2c492
Author: Sergei Poselenov <sposelenov@emcraft.com>
Date: Thu Jul 5 08:17:37 2007 +0200
Merged POST framework with the current TOT.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
commit b24629fa377214d63bb40d1360e354b6d3e4af56
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 13 13:23:15 2007 -0500
mpc86xx: Remove old CFG_CMD_* references.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 46175d9764da129bb4fd341cd2554dc7d55f5b2a
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 13 13:22:54 2007 -0500
Add MPC8568MDS to MAKEALL 85xx target.
It was missing from the original port submission.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2835e518c969e5124ba1174eef3e8375e12fa7d5
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 13 13:22:08 2007 -0500
include/configs: Use new CONFIG_CMD_* in 85xx board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 56b304ac2091689506088a9ae67f63fd6300cf16
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 13 13:21:37 2007 -0500
Fix #if typo in CONFIG_CMD_* changes.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f780b83316d9af1f61d71cc88b1917b387b9b995
Author: Niklaus Giger <niklausgiger@gmx.ch>
Date: Wed Jun 27 18:11:38 2007 +0200
resubmit: ppc4xx: Remove sequoia/sequioa.h. Cleanup ppc440.h for PPC440EPX
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
commit 04e6c38b766eaa2f3287561563c9e215e0c3a0d4
Author: Stefan Roese <sr@denx.de>
Date: Wed Jul 4 10:06:30 2007 +0200
ppc4xx: Update lwmon5 board
- Add optional ECC generation routine to preserve existing
RAM values. This is needed for the Linux log-buffer support
- Add optional DDR2 setup with CL=4
- GPIO50 not used anymore
- Lime register setup added
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6810a34677dbc446334f5e451f1682426dd33b49
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:17:28 2007 -0600
Fix Makefile to use $(MKCONFIG) macro for all board ports
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 90b1b2d69b9396ff2f01165ebc16c9a594eb5926
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:17:28 2007 -0600
Fix Makefile to use $(MKCONFIG) macro for all board ports
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 057004f4a4863554d56cc56268bfa7c7d9738e27
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:49 2007 -0600
Correct fixup relocation for mpc83xx
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 5af61b2f4b838a05f79be274f3e5a66edd2d9c96
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:44 2007 -0600
Correct fixup relocation for mpc8260
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f3a52fe05923935db86985daf9438e2f70ac39aa
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:39 2007 -0600
Correct fixup relocation for mpc824x
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit a85dd254c0577fca13627c46e93fc2ad4c4f1f00
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:34 2007 -0600
Correct fixup relocation for mpc8220
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 6f7576b20ecf0d040c3ac3b032b5cbc860e38a90
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:29 2007 -0600
Correct fixup relocation for MPC5xxx
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 3649cd99ba815b6601868735765602f00ef3692b
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:24 2007 -0600
Correct relocation fixup for mpc5xx
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f82b3b6304b620ef7e28bfaa1ea887a2ad2fa325
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:19 2007 -0600
Don't set gd->reloc_off if relocation of .fixup works correctly
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit e1a6144c32dc7de73bcdd33995de0148cbd0bd28
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:14 2007 -0600
Remove obsolete mpc83xx linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 17e32fc3908bf7089d3f16fc82a1c3ae674dd65b
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:09 2007 -0600
Consolidate mpc8260 linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit af7d38b393690d7eeaf418ac85a1e831a50d5fd0
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:34:04 2007 -0600
Remove obsolete mpc824x linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f94a3aecebc40ca0939c7d66d010009cf51be9e2
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:59 2007 -0600
Remove obsolete mpc824x linker scripts (3 of 4)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit a71c084f3ac7fedf144537db2b2da47323068833
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:53 2007 -0600
Remove obsolete mpc824x linker scripts (2 of 4)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f670a15468d1365241d40022b9408e1004181f5e
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:48 2007 -0600
Remove obsolete mpc824x linker scripts (1 of 4)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 09555bd45a04c0e54f172528d21bc18896550d28
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:43 2007 -0600
Remove obsolete mpc8220 linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 5efb992f046e51225c93d52f80fecbe433abd789
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:38 2007 -0600
Remove obsolete mpc5xxx linker scripts (3 of 3)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 07c13dfef65b31647e69d8b61daa1eec598add1a
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:33 2007 -0600
Remove obsolete mpc5xxx linker scripts (2 of 3)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit b4f67513a624ce85866c66c575bd2d9d7977d7f0
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:28 2007 -0600
Remove obsolete mpc5xxx linker scripts (1 of 3)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit b7d8e05f8675249b5f208aa73babeed384a4519d
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:23 2007 -0600
Remove obsolete mpc5xx linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 416a0b6d40f6eba3a2fc547253c16bda28d922f7
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:18 2007 -0600
Consolidate mpc83xx linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 5fc59175b92883ed5d2666a04e6bc49e70a4a365
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:13 2007 -0600
Consolidate mpc8260 linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 737f9eb02d7335df2b3e4d7a4d3348784d1da207
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:08 2007 -0600
Consolidate mpc824x linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 9c757b789a59a855db57b448dd825329c4e9c4a0
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:33:03 2007 -0600
Consolidate mpc8220 linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit d181c9a15cd41863fe24840d17848429f27d3c8c
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:32:58 2007 -0600
Consolidate mpc5xxx linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 287ac924adb7291bebe5086652a362a30ab28b13
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Jul 3 00:32:53 2007 -0600
Consolidate mpc5xx linker scripts
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 52b8704d0245e589f86d462e9ec25aeb7ecbbbdd
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Jul 4 00:43:53 2007 +0200
Fix a few file permission problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 78e0cf2de7be7f1eaeeb622eb61fd50e4d5e205c
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Jul 4 00:38:38 2007 +0200
Minor coding style cleanup. Rebuild CHANGELOG file.
commit 2f9c19e496acb6bb50d9299e1aab377625d48c38
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:44 2007 -0500
configs/ mpc86xx: Rewrite command line options using new CONFIG_CMD-* style.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 602ad3b33d9ceef83dbab46be68646d645d637ee
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:39 2007 -0500
README: Rewrite command line config to use CONFIG_CMD_* names.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 72a074cec68e5bad60d63206c050974e08afd804
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:34 2007 -0500
include/ non-config: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 5fcf543e0b6628c76ff48705b1b0566bfd11507b
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:28 2007 -0500
tools/ : Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 9107ebe0d352420895ab69b715697bdebc8caf50
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:23 2007 -0500
board/[k-z]*: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 5e378003d592ea828ec69d6defcd4de79096dd5c
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:19 2007 -0500
board/[Ma-i]*: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 737184114ec9c9e0ab94d6713536126073bd2472
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:15 2007 -0500
cpu/ non-mpc*: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f48070fe5fe440dfb5ee5268c920de70e48ea327
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:08 2007 -0500
cpu/mpc*/ : Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 0c505db0a0dc1f670b13ce3b4d3fbf1ec5b3cbd2
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:03:03 2007 -0500
lib_*/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 73f032021ec5f13cda8faa4e34b6de80960eb86f
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:58 2007 -0500
lib_ppc/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 98b79003c21c2578206003256de4e781d6b36ca8
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:53 2007 -0500
rtc/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 6e2115acb6a892d53a6881bf253ae41d3df39156
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:49 2007 -0500
net/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 45cdb9b72c94655c7308b464a2666057c0b286e0
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:34 2007 -0500
disk/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4e109ae98294a5ca7ff848b7652c7bfd4023a94a
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:20 2007 -0500
fs/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d5be43de93ff905c465e509d45a3164ef48d26e7
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:10 2007 -0500
drivers/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b453960d4fdb87b3970d96119b90df2ed024fc4a
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:02:05 2007 -0500
common/ non-cmd: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 65c450b47a62659d522cfa8f4fa1e4e5c60dccd0
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:01:54 2007 -0500
common/cmd_[i-z]* : Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit a76adc8142c1d956385a109e0b70f9319ede4d66
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:01:43 2007 -0500
common/cmd_[a-f]* : Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ec63b10b61fd68238d4c15c1cd04c0b38228e2c1
Author: Jon Loeliger <jdl@jdl.com>
Date: Mon Jun 11 19:01:34 2007 -0500
Introduce initial versions of new Command Config files.
Derive three new files from cmd_confdefs.h:
config_bootp.h - Has BOOTP related config options, not commands
config_cmd_all.h - Has a CONFIG_CMD_* definition for every command
config_cmd_default.h - Has a CONFIG_CMD_* definition for default cmds.
For now, include "config_bootp.h" for compatability until all
users of it directly include it properly.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1f2a05898658900dc5717761e27abf2052e67e13
Author: Mushtaq Khan <mushtaqk_921@yahoo.co.in>
Date: Sat Jun 30 18:50:48 2007 +0200
Fix S-ATA support.
Signed-off-by: mushtaq khan <mushtaqk_921@yahoo.co.in>
commit a5d71e290f3673269be8eefb4ec44f53412f9461
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Mon Jun 25 19:11:37 2007 +0200
[PCS440EP] get rid of CONFIG_PPC4xx_USE_SPD_DDR_INIT_HANG
Signed-off-by: Heiko Schocher <hs@denx.de>
commit a1bd6200eccd3a02040a955d5f43d3ee1fc9f93b
Author: Niklaus Giger <niklaus.giger@nestal.com>
Date: Mon Jun 25 17:03:13 2007 +0200
ppc4xx: PPC440EPx Emit DDR0 registers on machine check interrupt
This patch prints the DDR status registers upon machine check
interrupt on the 440EPx/GRx. This can be useful especially when
ECC support is enabled.
I added some small changes to the original patch from Niklaus to
make it compile clean.
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 807018fb7faceb429ce0cb47baa2073746b33a4e
Author: Niklaus Giger <niklaus.giger@nestal.com>
Date: Mon Jun 25 16:50:55 2007 +0200
ppc4xx: Fix O=buildir builds
This patch fixes the problem to assemble cpu/ppc4xx/start.S
experienced last week where building failed having specified
O=../build.sequoia.
Signed-off-by: Niklaus Giger <niklaus.giger@nestal.com>
commit 466fff1a7bb5fe764a06450626f6098219f446b8
Author: Stefan Roese <sr@denx.de>
Date: Mon Jun 25 15:57:39 2007 +0200
ppc4xx: Add pci_pre_init() for 405 boards
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6f35c53166213c24a5a0e2390ed861136ff73870
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Sun Jun 24 17:41:21 2007 +0200
ppc4xx: Maintenance patch for esd's CPCI405 derivats
-add pci_pre_init() for pci interrupt fixup code
-disable phy sleep mode via reset_phy() function
-use correct io accessors
-cleanup
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit 5a1c9ff0c44305b57cb4d8f9369bba90bcf0e1f8
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Sun Jun 24 17:23:41 2007 +0200
ppc4xx: Add pci_pre_init() for 405 boards
This patch adds support for calling a plattform dependant
pci_pre_init() function for 405 boards. This can be used to
move the current pci_405gp_fixup_irq() function into the
board code.
This patch also makes the CFG_PCI_PRE_INIT define obsolete.
A default function with 'weak' attribute is used when
a board specific pci_pre_init() is not implemented.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit 1636d1c8529c006d106287cfbc20cd0a246fe1cb
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Jun 22 23:59:00 2007 +0200
Coding stylke cleanup; rebuild CHANGELOG
commit 2dc64451b4c08ffd619372abfdc2506a2e2363b9
Author: Igor Lisitsin <igor@emcraft.com>
Date: Wed Apr 18 14:55:19 2007 +0400
Adapt log buffer code to support Linux 2.6
A new environment variable, "logversion", selects the log buffer
behaviour. If it is not set or set to a value other than 2, then the
old, Linux 2.4.4, behaviour is selected.
Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
commit a11e06965ec91270c51853407ff1261d3c740386
Author: Igor Lisitsin <igor@emcraft.com>
Date: Wed Mar 28 19:06:19 2007 +0400
Extend POST support for PPC440
Added memory, CPU, UART, I2C and SPR POST tests for PPC440.
Signed-off-by: Igor Lisitsin <igor@emcraft.com>
--
commit 566a494f592ae3b3c0785d90d4e1ba45574880c4
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Jun 22 19:11:54 2007 +0200
[PCS440EP] upgrade the PCS440EP board:
- Show on the Status LEDs, some States of the board.
- Get the MAC addresses from the EEProm
- use PREBOOT
- use the CF on the board.
- check the U-Boot image in the Flash with a SHA1
checksum.
- use dynamic TLB entries generation for the SDRAM
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 3a1f5c81b0b9557817a789bece839905581c2205
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 22 16:58:40 2007 +0200
ppc4xx: Fix problem with extended program_tlb() funtion
The recently extended program_tlb() function had a problem when
multiple TLB's had to be setup (for example with 512MB of SDRAM). The
virtual address was not incremented. This patch fixes this issue
and is tested on Katmai with 512MB SDRAM.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 02032e8f14751a1a751b09240a4f1cf9f8a2077f
Author: Rafal Jaworowski <raj@semihalf.com>
Date: Fri Jun 22 14:58:04 2007 +0200
[ppc] Fix build breakage for all non-4xx PowerPC variants.
- adapt to the more generic EXCEPTION_PROLOG and CRIT_EXCEPTION macros
- minor 4xx cleanup
commit d677b32855f577ae2690dcd64a172cdd706e0ffc
Author: Mike Frysinger <vapier@gentoo.org>
Date: Fri Jun 22 10:34:12 2007 +0200
[patch] add nand_init() prototype to nand.h
since nand_init() is expected to be called by other parts of u-boot, there
should be a prototype for it in nand.h
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 83b4cfa3d629dff0264366263c5e94d9a50ad80b
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Jun 20 18:14:24 2007 +0200
Coding style cleanup. Refresh CHANGELOG.
commit b3f9ec86e388207fd03dcdf7b145b9ed080bf024
Author: Stefan Roese <sr@denx.de>
Date: Tue Jun 19 17:22:44 2007 +0200
ppc4xx: Add bootstrap command for AMCC Sequoia (440EPx) eval board
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
commit df8a24cdd30151505cf57bbee5289e91bf53bd1b
Author: Stefan Roese <sr@denx.de>
Date: Tue Jun 19 16:42:31 2007 +0200
[ppc4xx] Fix problem with NAND booting on AMCC Acadia
The latest changes showed a problem with the location of the NAND-SPL
image in the OCM and the init-data area (incl. cache). This patch
fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 86ba99e34194394052d24c04dc40d1263d29a26f
Author: Stefan Roese <sr@denx.de>
Date: Tue Jun 19 16:40:58 2007 +0200
[ppc4xx] Change board/amcc/acadia/cpr.c to pll.c
Signed-off-by: Stefan Roese <sr@denx.de>
commit 8e585f02f82c17cc66cd229dbf0fd3066bbbf658
Author: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Date: Mon Jun 18 13:50:13 2007 -0500
Added M5329AFEE and M5329BFEE Platforms
Added board/freescale/m5329evb, cpu/mcf532x, drivers/net,
drivers/serial, immap_5329.h, m5329.h, mcfrtc.h,
include/configs/M5329EVB.h, lib_m68k/interrupts.c, and
rtc/mcfrtc.c
Modified CREDITS, MAKEFILE, Makefile, README, common/cmd_bdinfo.c,
common/cmd_mii.c, include/asm-m68k/byteorder.h, include/asm-m68k/fec.h,
include/asm-m68k/io.h, include/asm-m68k/mcftimer.h,
include/asm-m68k/mcfuart.h, include/asm-m68k/ptrace.h,
include/asm-m68k/u-boot.h, lib_m68k/Makefile, lib_m68k/board.c,
lib_m68k/time.c, net/eth.c and rtc/Makefile
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
commit 093172f08d6afb3f34d8a2f26ee0ee874261cf27
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Jun 17 19:04:11 2007 +0200
[fix] email reparation
commit 3666afffe7baf859c6ae0ce2bebbc8ab7e512ddc
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Jun 17 19:03:21 2007 +0200
[FIX] fix microblaze file permitission
commit e73846b7cf1e29ae635bf9bb5570269663df2ee5
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 15 11:33:41 2007 +0200
[ppc4xx] Change lwmon5 port to work with recent 440 exception rework
Now CONFIG_440 has to be defined in all PPC440 board config files.
Signed-off-by: Stefan Roese <sr@denx.de>
commit efa35cf12d914d4caba942acd5a6c45f217de302
Author: Grzegorz Bernacki <gjb@semihalf.com>
Date: Fri Jun 15 11:19:28 2007 +0200
ppc4xx: Clean up 440 exceptions handling
- Introduced dedicated switches for building 440 and 405 images required
for 440-specific machine instructions like 'rfmci' etc.
- Exception vectors moved to the proper location (_start moved away from
the critical exception handler space, which it occupied)
- CriticalInput now serviced (with default handler)
- MachineCheck properly serviced (added a dedicated handler and return
subroutine)
- Overall cleanup of exceptions declared with STD_EXCEPTION macro (unused,
unhandled and those not relevant for 4xx were eliminated)
- Eliminated Linux leftovers, removed dead code
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit b765ffb773f5a3cd5aa94ec76b6a05276b8cd5b2
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 15 08:18:01 2007 +0200
[ppc4xx] Add initial lwmon5 board support
This patch adds initial support for the Liebherr lwmon5 board euqipped
with an AMCC 440EPx PowerPC.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 85f737376d5ff3d5f0d45a8b657686326d175307
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 15 07:39:43 2007 +0200
[ppc4xx] Extend 44x GPIO setup with default output state
The board config array CFG_440_GPIO_TABLE for the ppc440 GPIO setup
is extended with the default GPIO output state (level).
Signed-off-by: Stefan Roese <sr@denx.de>
commit dbca208518e5e7f01a6420588d1cd6e60db74c2b
Author: Stefan Roese <sr@denx.de>
Date: Thu Jun 14 11:14:32 2007 +0200
[ppc4xx] Extend program_tlb() with virtual & physical addresses
Now program_tlb() allows to program a TLB (or multiple) with
different virtual and physical addresses. With this change, now one
physical region (e.g. SDRAM) can be mapped 2 times, once with caches
diabled and once with caches enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9912121f7ed804ea58fd62f3f230b5dcfc357d88
Author: Detlev Zundel <dzu@denx.de>
Date: Wed May 23 19:02:41 2007 +0200
Change 'repeatable' attribute of some commands to sensible values.
Most prominently this changes 'erase' to be non-repeatable.
Signed-off-by: Detlev Zundel <dzu@denx.de>
commit 5afb202093f6a001797db92cf695b93a70ea9ab4
Author: Detlev Zundel <dzu@denx.de>
Date: Wed May 23 18:47:48 2007 +0200
Fix 'run' not to continue after interrupted command
Signed-off-by: Detlev Zundel <dzu@denx.de>
commit 9b7464a2c88614e1061f509c48930a3d240d1a35
Author: Jason Jin <Jason.jin@freescale.com>
Date: Mon Jun 11 15:14:24 2007 +0200
USB: This patch fix readl in ohci swap reg access.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 8f8416fada9faf94b9a92f21fe6000643cb521d5
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Fri Jun 8 14:52:22 2007 +0200
TQM5200: Add Flat Device Tree support, update default env. accordingly.
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit 9045f33c023f698660a2e45d1b2194c0711abebc
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Jun 8 10:24:58 2007 +0200
Fix config problems on SC3 board; make ide_reset_timeout work.
commit fba3fb0449b8a54542aed1e729de76e7f5a2ff1b
Author: Benoît Monin <bmonin@adeneo.eu>
Date: Fri Jun 8 09:55:24 2007 +0200
[PATCH] fix gpio setting when using CFG_440_GPIO_TABLE
Set the correct value in GPIOx_TCR when configuring the gpio
with CFG_440_GPIO_TABLE.
Signed-off-by: Benoit Monin <bmonin@adeneo.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
commit f539edc076cfe52bff919dd512ba8d7af0e22092
Author: Vadim Bendebury <vbendeb@google.com>
Date: Thu May 24 15:52:25 2007 -0700
cosmetic changes to bcm570x driver
This is a cosmetic only changes submission.
It affects files relevant to bcm570x driver.
the commands used to generate this change was
cd drivers
Lindent -pcs -l80 bcm570x.c bcm570x_lm.h bcm570x_mm.h tigon3.c tigon3.h
The BMW target (the only one using this chip so far) builds cleanly, the
`before and after' generated object files for drivers/bcm570x.c and
drivers/tigon3.o are identical as reported by objdump -d
Signed-off-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit 725671ccd2cd04c9ebc50c9e5a94dd8cbade66b7
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Jun 6 16:26:56 2007 +0200
Coding Style cleanup; generate new CHANGELOG file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 19d763c35e0b5568eaf0b8adbf7a68ccfe7fa243
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Jun 6 11:49:44 2007 +0200
TRAB, USB: update trab board configuration for use of generic ohci driver
commit dace45acd1c1357daa9322099d07c9a9e08b0024
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Jun 6 11:49:43 2007 +0200
USB: ohci fixes and cleanup for ppc4xx and yosemite board.
commit 72657570b61635c74fa0c3f0e9e7d0671a9d08df
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Jun 6 11:49:43 2007 +0200
USB: ohci fixes and cleanup for mpc5xxx and IceCube board config
commit fc43be478f2aa37ce38acd85355038866e4162af
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Jun 6 11:49:35 2007 +0200
USB/OHCI: endianness cleanup in the generic ohci driver
commit c440bfe6d6d92d66478a7e84402b31f48413617b
Author: Stefan Roese <sr@denx.de>
Date: Wed Jun 6 11:42:13 2007 +0200
ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval board
This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
commit 18135125f909948b85d1d6881ab4ac0efb4a1c58
Author: Rodolfo Giometti <giometti@linux.it>
Date: Wed Jun 6 10:08:14 2007 +0200
Files include/linux/byteorder/{big,little}_endian.h define
__BIG_ENDIAN and __LITTLE_ENDIAN.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
commit a81d1c0b85b13e9d45f2d87de96a51a6e0ef0f82
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Wed Jun 6 10:08:14 2007 +0200
Add USB PCI-OHCI, USB keyboard and event poll support to the
MPC8641HPCN board config file.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit 4dae14ce8fbdf380017dc54f172218e7d2acc889
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Wed Jun 6 10:08:14 2007 +0200
USB PCI-OHCI, interrupt pipe and usb event poll support
This patch added USB PCI-OHCI chips support, interrupt pipe support
and usb event poll support. For supporting the USB interrupt pipe, the
globe urb_priv is moved to purb in ed struct. Now, we can process
several urbs at one time. The interrupt pipe support codes are ported
from Linux kernel 2.4.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit fdcfaa1b02268b2899e374b35adf936c911a47eb
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Wed Jun 6 10:08:13 2007 +0200
USB event poll support
This patch adds USB event poll support, which could be used in usbkbd
and other usb devices driver when the asynchronous interrupt
processing is supported.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com
commit 9a1d00fa47c1e05e3fdb60b33213af4e18d4c18e
Author: Rodolfo Giometti <giometti@linux.it>
Date: Wed Jun 6 10:08:12 2007 +0200
ISP116x: delay for crappy USB keys
Using some (very) slow USB keys cause the USB host controller buffers
are not ready to be read by the CPU so we need an extra delay before
reading the USB storage data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
commit 09444143670c9c2243cb7aba9f70b3713d33bed1
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Jun 6 10:08:12 2007 +0200
Change duplicate usb_cpu_init_fail to usb_board_init_fail
Thanks to Liew Tsi Chung <Tsi-chung.Liew@freescale.com> for pointing
this out.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
commit 32922cdc470fdfd39bea0c1c4f582d3fb340421e
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Tue Jun 5 12:30:52 2007 -0500
mpc8641 image size cleanup
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit e3cbe1f93c5722f8ebbad468e30c069a2b511097
Author: Benoît Monin <bmonin@adeneo.eu>
Date: Mon Jun 4 08:36:05 2007 +0200
[PATCH] Fix ppc4xx bootstrap letter displayed on startup
The attached patch is mainly cosmetic, allowing u-boot to
display the correct bootstrap option letter according to the
datasheets.
The original patch was extended with 405EZ support by Stefan
Roese.
Signed-off-by: Benoit Monin <bmonin@adeneo.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5b1313fb2758ffce8b624457f777d8cc6709608d
Author: Nikita V. Youshchenko <yoush@debian.org>
Date: Wed May 23 12:45:19 2007 +0400
fix compilation problem for mpc8349itx CFG_RAMBOOT
Current include/configs/MPC8349ITX.h does contain some support for building
image that will be started from memory (without putting in into flash).
It could be triggered by building with TEXT_BASE set to a low value.
However, this support is incomplete: using of low TEXT_BASE causes
defining configuration macros in inconsistent way, which later leads
to compilation errors. In particular. flash support is being disabled,
but then flash structures get referenced.
This patch fixes this, making it possible to build with low TEXT_BASE.
Signed-Off-By: Nikita Youshchenko <yoush@debian.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 8a364f0970de49949d635e60accf463c6443ef8c
Author: Nikita V. Youshchenko <yoush@debian.org>
Date: Wed May 23 12:45:25 2007 +0400
add missing 'console' var to default mpc8349itx config
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 18d156eb37c90fadc8ec7a81a3b89176161f85b7
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 16:18:17 2007 +0200
ppc4xx: Add missing file for Bamboo NAND booting support
Signed-off-by: Stefan Roese <sr@denx.de>
commit 155a96478a0881e6da96cbbbcf34952d6a3b1b4b
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:58:19 2007 +0200
ppc4xx: Undo Sequoia patch for dynamic EBC speed support of 83MHz
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9d9096043e8f713d4bf1743d32e1459e6a11644b
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:29:04 2007 +0200
ppc4xx: Update Sequoia NAND booting support with ECC
Signed-off-by: Stefan Roese <sr@denx.de>
commit cf959c7d6687567c308e366e9581e1a5aff5cc5b
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:27:11 2007 +0200
ppc4xx: Add NAND booting support for AMCC Bamboo (440EP) eval board
This patch adds NAND booting support for the AMCC Bamboo eval board.
Since the NAND-SPL boot image is limited to 4kbytes, this version
only supports the onboard 64MBytes of DDR. The DIMM modules can't be
supported, since the setup code for I2C DIMM autodetection and
configuration is too big for this NAND bootloader.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 42be56f53c8b107868e6125c8524ae84293e95a7
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:23:04 2007 +0200
NAND: Add ECC support to NAND booting support in nand_spl/nand_boot.c
The U-Boot NAND booting support is now extended to support ECC
upon loading of the NAND U-Boot image.
Tested on AMCC Sequoia (440EPx) and Bamboo (440EP).
Signed-off-by: Stefan Roese <sr@denx.de>
commit a471db07fbb65a841ffc9f4f112562b945230f98
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:19:29 2007 +0200
ppc4xx: Prepare Bamboo port for NAND booting support
This patch updates the "normal" Bamboo NOR booting port, so
that it is compatible with the coming soon NAND booting
Bamboo port.
It also enables the 2nd NAND flash on the Bamboo.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 53ad02103fb8be4138a9937a8ab91fcdff7b4987
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:16:58 2007 +0200
ppc4xx: Update in_be32() functions and friends to latest Linux version
Signed-off-by: Stefan Roese <sr@denx.de>
commit 91da09cfbce0c1de05d6d84aa8363d666fa7ea3c
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:15:12 2007 +0200
NAND: Add hardware ECC support to the PPC4xx NAND driver ndfc.c
This patch adds hardware ECC support to the NDFC driver. It also
changes the register access from using the "simple" in32/out32
functions to the in_be32/out_be32 functions, which make sure
that the access is correctly synced. This is the only recommended
access to SoC registers in the current Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 17b5e862287cca76f19dcf8b741e61a7d06617f2
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:12:15 2007 +0200
NAND: Update nand_ecc.c to latest Linux version
This patch updates the nand_ecc code to the latest Linux version.
The main reason for this is the more compact code. This makes
it possible to include the ECC code into the NAND bootloader
image (NAND_SPL) for PPC4xx.
Signed-off-by: Stefan Roese <sr@denx.de>
commit d2d432760d2199d0e8558fdd9d1789b8131abcf7
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 15:09:50 2007 +0200
ppc4xx: 44x DDR driver code cleanup and small fix for Bamboo
Signed-off-by: Stefan Roese <sr@denx.de>
commit e4bbed2803a2ad0521c7362f5d3e065f99abaedc
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 13:45:24 2007 +0200
ppc4xx: Change Luan config file to support ECC
With the updated 44x DDR2 driver the Luan board now supports
ECC generation and checking.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 7187db73491c8de0fb56efb5e5134ba5ec443089
Author: Stefan Roese <sr@denx.de>
Date: Fri Jun 1 13:45:00 2007 +0200
ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
Add config option for 180 degree advance clock control as needed
for the AMCC Luan eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
commit ee1529838abbfaa35f14e3ffbeaaba693159475f
Author: Wolfgang Denk <wd@denx.de>
Date: Thu May 31 17:20:09 2007 +0200
Add support for STX GP3SSA (stxssa) Board with 4 MiB flash.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 7049288fb1f16f1b317140226cdebd07bd416395
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 17:26:46 2007 +0200
Motion-PRO: Code cleanup, fix of a typo in OF_STDOUT_PATH.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
commit 4520fd4d2c450da49637216aa0e53739b61c60ac
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 17:06:36 2007 +0200
Motion-PRO: Add support for redundant environment.
Enable redundant environment, add a MTD partition for it; also add env.
variable command for passing MTD partitions to the kernel command line.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit a26eabeec31746f06d309103690892805696e344
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 17:05:11 2007 +0200
Motion-PRO: Change maximum console buffer size from 256 to 1024 bytes.
Allow passing longer command line to the kernel - useful especially
for passing MTD partition layout.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit 9160b96f71483a116de81c68985e8ee306d36764
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 17:04:18 2007 +0200
Fix: Add missing NULL termination in strings expanded by macros parser.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit 630ec84aef7228fc1dbfb38dec78541403a786cd
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 17:03:37 2007 +0200
Motion-PRO: Update EEPROM's page write bits and write delay.
Change EEPROM configuration according to the datasheet: "The 24C01A and 24C02A
have a page write capability of two bytes", and "This device offers fast (1ms)
byte write". Add 3ms of extra delay.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit c00125e07c1ebc125bab40e1e18bceed8be0c162
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 16:58:45 2007 +0200
MPC5XXX, Motion-PRO: Fix PHY initialization problem.
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3ef2c062744d733787c7e530a1b8761, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit 93b78f534a6e708b4cf1a4ffb4d8438c67a007db
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 16:57:15 2007 +0200
Motion-PRO: Add support for the temperature sensor.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit c75e639630cc132dc19cd1ecda5922c0db0bfbba
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 16:55:23 2007 +0200
Motion-PRO: Add displaying of CPLD revision information during boot.
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit c99512d6bd3973f01ca2fc4896d829b46e68f150
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 16:53:43 2007 +0200
MPC5xxx: Change names of defines related to IPB and PCI clocks.
Both CFG_PCISPEED_66 and CFG_IPBSPEED_133 are misnamed, as defining
them does not cause PCI or IPB clocks to run at the specified speed.
Instead, they configure divisors used to calculate said clocks. This
patch renames the defines according to their real function.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit a11c0b85dc3664bb3c1e781137118730c8f619ab
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sun May 27 16:51:48 2007 +0200
Motion-PRO: Add LED support.
Signed-off-by: Jan Wrobel <wrr@semihalf.com>
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
commit 7ebb4479b07ff294eb4d76e420753a0349f7c93b
Author: Ulf Samuelsson <ulf@atmel.com>
Date: Thu May 24 12:12:47 2007 +0200
[PATCH][NAND] Define the Vendor Id for Micron NAND Flash
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
commit d756894722c888d09a9fa1df8323753772d3dcce
Author: Stefan Roese <sr@denx.de>
Date: Thu May 24 09:49:00 2007 +0200
ppc4xx: Fix small 405EZ OCM initilization bug in start.S
As pointed out by Bruce Adler <bruce.adler@acm.org> this patch
fixes a small bug in the 405EZ OCM initialization. Thanks for
spotting.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5d4a179013d59a76446462e1eb0a969fba63eb81
Author: Stefan Roese <sr@denx.de>
Date: Thu May 24 08:22:09 2007 +0200
ppc4xx: Update AMCC Acadia support for board revision 1.1
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 822d55365bb557e084d0e33625a6dedcc866110b
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed May 23 14:09:46 2007 -0500
Add LIST_86xx MAKEALL target for PowerPC builds.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 9f0077abd69f7a7c756a915b961037302be3e6f2
Author: Stefan Roese <sr@denx.de>
Date: Tue May 22 12:48:09 2007 +0200
ppc4xx: Use do { ... } while (0) for CPR & SDR access macros
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6f3dfc139a838b0841c151efe00ad47db2366e79
Author: Stefan Roese <sr@denx.de>
Date: Tue May 22 12:46:10 2007 +0200
ppc4xx: Add 405 support to 4xx NAND driver ndfc.c
This patch adds support for 405 PPC's to the 4xx NAND driver
ndfc.c. This is in preparation for the new AMCC 405EZ.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 10603d76767426be803dadd4fb688b97eb69481c
Author: Stefan Roese <sr@denx.de>
Date: Mon May 21 07:41:22 2007 +0200
ppc4xx: Fix problem in 405EZ OCM initialization
As spotted by Bruce Adler this patch fixes an initialization problem
for the 405EZ OCM.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3e3b956906eba9e4ad7931581ecedaad10eccce8
Author: Peter Pearse <peter.pearse@arm.com>
Date: Fri May 18 16:47:03 2007 +0100
Reduce line lengths to 80 characters max.
commit 93ef45c9ddfdd9fc17c4e74bd8e2f2456580eb72
Author: Peter Pearse <peter.pearse@arm.com>
Date: Fri May 18 14:34:07 2007 +0100
Makefile permissions
commit 1443a31457d68f7e8f0b9403e9832ec1e79dc59d
Author: Peter Pearse <peter.pearse@arm.com>
Date: Fri May 18 14:33:11 2007 +0100
Makefile permissions
commit 255a3577c848706441daee0174543efe205a77f8
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed May 16 16:52:19 2007 -0500
Reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 70124c2602ae2d4c5d3dba05b482d91548242de8
Author: Stefano Babic <sbabic@denx.de>
Date: Wed May 16 14:49:12 2007 +0200
Fix compile problem cause my Microblaze merge
Signed-off-by: Stefano Babic <sbabic@denx.de>
commit ada4697d0230d6da552867777f98a67ec3ba2579
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Wed May 16 13:23:10 2007 +0200
[PATCH] Run new sequoia boards with an EBC speed of 83MHz
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
commit a7676ea7732f3c596805079fed7e5c9fac652cfc
Author: Wolfgang Denk <wd@denx.de>
Date: Wed May 16 01:16:53 2007 +0200
Minor Coding Style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit d62f64cc23a940eafe712c776b3249e4160753d1
Author: Wolfgang Denk <wd@denx.de>
Date: Wed May 16 00:13:33 2007 +0200
Coding Style Cleanup, new CHANGELOG
commit 3162eb836903c8b247fdc7470dd39bfa6996f495
Author: Wolfgang Denk <wd@denx.de>
Date: Tue May 15 23:38:05 2007 +0200
Minor coding style cleanup.
commit 66d9dbec1cc27d6398ee6cf84639dbe14971251e
Author: mushtaq khan <mushtaq_k@procsys.com>
Date: Fri Apr 20 14:23:02 2007 +0530
Add driver for S-ATA-controller on Intel processors with South
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
commit 644e6fb4eb8be90ea04ba34b643a8bf019d680e0
Author: mushtaq khan <mushtaq_k@procsys.com>
Date: Mon Apr 30 15:57:22 2007 +0530
Fixes bug clearing the bss section for i386
Hi,
There is a bug in the code of clearing the bss section for processor
i386.(File: cpu/i386/start.S)
In the code, bss_start addr (starting addr of bss section) is put into
the register %eax, but the code which clears the bss section refers to
the addr pointed by %edi.
This patch fixes this bug by putting bss_start into %edi register.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
commit c3243cf7b490057277d61acffe4ad0946f9eb4a4
Author: Joe Hamman <joe.hamman@embeddedspecialties.com>
Date: Mon Apr 30 16:47:28 2007 -0500
Add support for BCM5464 Quad Phy
Added support for Broadcom's BCM5464 Quad Phy
Signed-off-by: Joe Hamman <joe.hamman@embeddedspecialties.com>
commit 1b305bdc754c8468e1d5d858f5dcf8a7a0a4bb7a
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Wed May 9 08:10:57 2007 +0800
Search the exception table with linear algorithm
Search the exception table with linear algorithm instead of
bisecting algorithm.
Because the exception table might be unsorted.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 5dfaa50eb819686bfba1927e8c5b8a70a4d65fd3
Author: Aubrey.Li <aubrey.adi@gmail.com>
Date: Mon May 14 11:47:35 2007 +0800
Fix compilation issues on MACOSX
Singed-off-by: Marc Hoffman <Marc.Hoffman@analog.com>
Signed-off-by: Aubrey Li <aubrey.adi@gmail.com>
commit 56fd7162985c412317bbf763a225fba23c64fd31
Author: Stephen Williams <steve@icarus.com>
Date: Tue May 15 07:55:42 2007 -0700
Fix for compile of JSE target
The attached patch fixes the compile of the JSE board in the
denx git as of 14 may 2007. It is an extremely simple patch,
it just adds the missing define of CFG_SYSTEMACE_WIDTH.
Fix to compile JSE against 20070514 git of u-boot
commit 61936667e86a250ae12fd2dc189d3588f0a59e0b
Author: Stefan Roese <sr@denx.de>
Date: Fri May 11 12:01:49 2007 +0200
ppc4xx: Add mtcpr/mfcpr access macros
Signed-off-by: Stefan Roese <sr@denx.de>
commit 343c48bd84606c4025c8a7c7263fda465d6e284c
Author: Stefan Roese <sr@denx.de>
Date: Fri May 11 12:01:06 2007 +0200
ppc4xx: Set bd->bi_pci_busfreq on 440EPx/GRx too
Signed-off-by: Stefan Roese <sr@denx.de>
commit 7d98ba770a7eaefa29ce927f31a0956df85bf650
Author: Piotr Kruszynski <ppk@semihalf.com>
Date: Thu May 10 16:55:52 2007 +0200
[Motion-PRO] Add MTD and JFFS2 support, also add default partition
definition.
commit 65fb6a676e821f9570a2a376dc204bf611ce5f81
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed May 9 11:42:44 2007 +0100
Add the board directory for SMN42
commit 160131bf965785419626df6c388729fe0b597992
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed May 9 11:41:58 2007 +0100
Add the files for the SMN42 board
commit 5c6d2b5a500f8c49670de8910150b78a41f781fc
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed May 9 11:40:34 2007 +0100
Remove the deleted files for the SMN42 patch
commit b0d8f5bf0d215adc9424cb228b2484dbf07f7761
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed May 9 11:37:56 2007 +0100
New board SMN42 branch
commit 29f3be0caf0799ca6b89dfd9824c15619a50000f
Author: Peter Pearse <peter.pearse@arm.com>
Date: Wed May 9 10:24:38 2007 +0100
Makefile permissions
commit b84289b595731e8851df46e893845cc1322c9b9b
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Tue May 8 14:17:07 2007 -0500
8641hpcn: Fix Makefile after moving pixis to board/freescale.
The OBJTREE != SRCTREE build scenario was broken.
This fixes it.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit e69f66c6ebe82bbbd1da766bc4eda40ec7ee5af1
Author: Michal Simek <monstr@monstr.eu>
Date: Tue May 8 15:57:43 2007 +0200
add: reading special purpose registers
commit 1a50f164beb065f360fbddb76029607d6b099698
Author: Michal Simek <monstr@monstr.eu>
Date: Tue May 8 14:52:52 2007 +0200
add: Microblaze V5 exception handling
commit ab874d5047e5d30dbc1e517ff26083efffa98ecb
Author: Michal Simek <monstr@monstr.eu>
Date: Tue May 8 14:39:11 2007 +0200
add: FSL control read and write
commit de1de02a7cbf05e6b63e0d8ffc624f12493f6ba3
Author: Piotr Kruszynski <ppk@semihalf.com>
Date: Tue May 8 13:05:44 2007 +0200
[Motion-PRO] Add support for I2C, EEPROM and RTC.
commit fa5c2ba123b1bf88455bfc21db5e786ca045029d
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue May 8 10:23:56 2007 +0200
[Motion-PRO] Add ATA support. Add CF-booting commands to the default
environment.
commit 06241d50a3ab1b20a0b08baeeaffcaa23ae4b839
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue May 8 09:39:12 2007 +0200
[Motion-PRO] Change IPB clock frequency from 50MHz to 100MHz. This
eliminates networking problems in Linux (timeouts).
commit 1f1369c34b629be94702684d41d3fddf0f6193e7
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue May 8 09:21:57 2007 +0200
[Motion-PRO] Enable Flat Device Tree support and modify default environment
to allow booting of FDT-expecting kernels.
commit fb05f6da35ea1c15c553abe6f23f656bf18dc5db
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 23:58:31 2007 +0200
new: USE_MSR_INTR support
commit 008861a2f3ef2c062744d733787c7e530a1b8761
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Mon May 7 22:36:15 2007 +0200
[MPC5xxx] There are networking problems on the Motion-PRO board with
current PHY initalization code (tftp timeouts all the time). This commit
temporarily disables PHY initalization sequence to make the networking
operational, until a fix is found.
commit abca901869c3760b6c5fecb825db6c1d91a78a93
Author: Wolfgang Denk <wd@denx.de>
Date: Mon May 7 22:10:36 2007 +0200
Get rid of duplicated file (see include/configs/sbc8560.h instead)
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 207b7b2c9d9752e0f6478c30c29b7087f6e6cbb6
Author: Wolfgang Denk <wd@denx.de>
Date: Mon May 7 22:07:08 2007 +0200
Get rid of duplicated file (see doc/README.SBC8560 instead)
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit a7bac7e9b57ba948051beb19ec5be3a75ce75383
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 19:43:10 2007 +0200
fix: read and write MSR - repair number of parameters
commit 193b4a3bb3acaddf798da8de0da05d94ba8774ee
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Mon May 7 19:42:49 2007 +0200
[PATCH] ppc4xx: Fix CONFIG_SYS_CLK_FREQ definition in Sequoia config file
A '3' got cut off in the formatting of the last patch to automatically
change the clock speed of the system clock on sequoia board.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 19bf1fbad7f19d5a120be9b1daf136e052fcab39
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 19:33:51 2007 +0200
new: fsl interrupt support
FSL_Has_data is connected to INTC.
commit 792032baa7d625e34c981ab6df521911bd8dc861
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 19:30:12 2007 +0200
fix: interrupt handler
remove asm code
commit f3f001a341ef185d0f13841be5b5dc3395aacc31
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 19:25:08 2007 +0200
fix: remove asm code
commit fb7c2dbef02c9f6f8d7b04ec4c2bfb91418b9c01
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 19:12:43 2007 +0200
fix: clean interrupt
commit 42efed6130c8fcf7da881385b5427065d2801757
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 17:22:25 2007 +0200
fix: interrupt handler for multiple sources
commit 48fbd3a4cdabbebc1debd7eed73c00c2caf914f6
Author: Michal Simek <monstr@monstr.eu>
Date: Mon May 7 17:11:09 2007 +0200
new: add writing to msr register
commit 3a619dd7bed03e8b4d22a3911f90fd12af5376c2
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon May 7 16:43:56 2007 +0200
Fix an ancient CHANGELOG conflict
commit ac4cd59d59c9bf3f89cb7a344abf8184d678f562
Author: Timur Tabi <timur@freescale.com>
Date: Sat May 5 08:12:30 2007 +0200
5xxx: write MAC address to mac-address and local-mac-address
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
commit a9d87e2707dcb249f6bb7f7ff7e00acd8cda9fd2
Author: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Date: Sun Apr 29 14:01:54 2007 +0200
[PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot message
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
message. Use PVR to distinguish between the two variants, and print proper CPU
information.
Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 4ec5bd55ed1ffa91a774af298769621f4fbb18c1
Author: Ladislav Michl <ladis@linux-mips.org>
Date: Wed Apr 25 16:01:26 2007 +0200
[PATCH] simplify silent console
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefan Roese <sr@denx.de>
commit b7598a43f2b421a713d8135e98a42c37d9eb9df0
Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Date: Mon Apr 23 15:30:39 2007 +0200
[PATCH] Avoid assigning PCI resources from zero address
If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
core complains and IDE drivers fails to work. Also, assigning zero to a BAR
was illegal according to PCI 2.1 (the later revisions seem to have excluded the
sentence about "0" being considered an invalid address) -- so, use a reasonable
starting value of 0x1000 (that's what the most Linux archs are using).
Alternatively, one might have fixed the calls to pci_set_region() individually
(some code even seems to have taken care of this issue) but that would have
been a lot more work. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
commit 9ffd451afeb08e5be7ddae680487ec962b2bca25
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Mon Apr 23 14:00:11 2007 +0200
[patch] setenv(...) can delete environmentalvariables
update setenv() function so that entering a NULL value for the
variable's value will delete the environmental variable
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Acked-by: Stefan Roese <sr@denx.de>
commit ebd0a0ae05a44769c4e27458ad4e9f3438250443
Author: Mike Frysinger <vapier@gentoo.org>
Date: Mon Apr 23 13:54:24 2007 +0200
[patch] use unsigned char in smc91111 driver for mac
the v_mac variable in the smc91111 driver is declared as a signed char ...
this causes problems when one of the bytes in the MAC is "signed" like 0xE0
because when it gets printed out, you get a display like:
0xFFFFFFE0 and that's no good
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
commit ffc50f9bb194343c6303517a517708457a5eb6b8
Author: Michal Simek <monstr@monstr.eu>
Date: Sat May 5 18:54:42 2007 +0200
new: FSL and MSR support #2
commit f7e2e0eb0668136305f78bb9c21be79b48a34247
Author: Michal Simek <monstr@monstr.eu>
Date: Sat May 5 18:27:16 2007 +0200
new: FSL and MSR support
commit 2f15278c2eb911c668b4fe562130b78cf554d139
Author: Wolfgang Denk <wd@denx.de>
Date: Sat May 5 18:23:11 2007 +0200
Coding stylke cleanup; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 885ec89b648a899a2f32393fd3ffd9f7234c4402
Author: Wolfgang Denk <wd@denx.de>
Date: Sat May 5 18:05:02 2007 +0200
Add STX GP3 SSA board to MAKEALL script; update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5499645b3fe17a548af9dfc479ca6e2455f179a2
Author: Wolfgang Denk <wd@denx.de>
Date: Sat May 5 17:15:50 2007 +0200
Make "file" command happy with some config.mk files; update CHANGELOG
commit e3b8c78bc2489c27ae020986ef0eaca684866cef
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Sat May 5 08:32:14 2007 +0200
ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHz
The AMCC Secquoia board has been changed in a new revision from using a
33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD
indicates the difference. This patch reads that bit and uses the correct
clock speed for the board. This code is backward compatable will all
prior boards. All prior boards will be read as 33.000.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit f544ff6656fca263ed1ebe39899b6d95da67c8b8
Author: Stefan Roese <sr@denx.de>
Date: Sat May 5 08:29:01 2007 +0200
ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND booting
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2f550ab976405300f5b07bf2890800840d0aa05f
Author: Timur Tabi <timur@freescale.com>
Date: Sat May 5 08:12:30 2007 +0200
5xxx: write MAC address to mac-address and local-mac-address
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
commit a79886590593ba1d667c840caa4940c61639f18f
Author: Thomas Knobloch <knobloch@siemens.com>
Date: Sat May 5 07:04:42 2007 +0200
NAND: Wrong calculation of page number in nand_block_bad()
In case that there is no memory based bad block table available the
function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call
nand_block_bad() directly. When parameter 'getchip' is set to zero,
nand_block_bad() will not right shift the offset to calculate the
correct page number.
Signed-off-by: Thomas Knobloch <knobloch@siemens.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9877d7dcd1eebe61aa5d8b8ffe9c048ea426e6f6
Author: Wolfgang Denk <wd@denx.de>
Date: Fri May 4 10:02:33 2007 +0200
Fix initrd length corruption in bootm command.
When using FDT Images, the length of an inital ramdisk was
overwritten (bug introduced by commit 87a449c8, 22 Aug 2006).
Patches by Timur Tabi & Johns Daniel.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 068aab660bc3912b930be5540e6b3f3fd6ad3c96
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu May 3 19:43:52 2007 -0500
mpc83xx: fix trivial error in MAKEALL
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit c64a89d6ce8584b9fc64f4e85da9ecac3cfc2c2a
Author: Wolfgang Denk <wd@denx.de>
Date: Thu May 3 16:34:41 2007 +0200
Update board configuration for STX GP3SSA board:
Enable hush shell, environment in flash rather in EEPROM,
more user-friendly default environment, etc.
The simple EEPROM environment can be selected easily in the board
config file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 2c6fb199dc5756fc72f49d1f4de105e089049d65
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Apr 24 14:37:49 2007 +0200
Cleanup STX GP3SSA code; fix build and compile problems.
commit 35171dc04e028ecacc23ad916a66295472555dbf
Author: Dan Malek <dan@embeddedalley.com>
Date: Fri Jan 5 09:15:34 2007 +0100
Add support for STX GP3SSA (stxssa) Board
Signed-off-by Dan Malek, <dan@embeddedalley.com>
commit f2134f8e9eb006bdcd729e89f309c07b2fa45180
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed May 2 13:31:53 2007 +0200
macb: Don't restart autonegotiation if we already have link
Rework macb_phy_init so that it doesn't attempt to re-negotiate if the
link is already up.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 04fcb5d38bc90779cd9a710d60702075986f0e29
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed May 2 13:22:38 2007 +0200
macb: Introduce a few barriers when dealing with DMA descriptors
There were a few theoretical possibilities that the compiler might
optimize away DMA descriptor reads and/or writes and thus cause
synchronization problems with the hardware. Insert barriers where
we depend on reads/writes actually hitting memory.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit ffa621a0d12a1ccd81c936c567f8917a213787a8
Author: Andy Fleming <afleming@freescale.com>
Date: Sat Feb 24 01:08:13 2007 -0600
Cleaned up some 85xx PCI bugs
* Cleaned up the CDS PCI Config Tables and added NULL entries to
the end
* Fixed PCIe LAWBAR assignemt to use the cpu-relative address
* Fixed 85xx PCI code to assign powar region sizes based on the
config values (rather than hard-coding them)
* Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 6743105988fc44d5b0d30388c790607835aae7a6
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Apr 23 02:54:25 2007 -0500
Add support for the 8568 MDS board
This included some changes to common files:
* Add 8568 processor SVR to various places
* Add support for setting the qe bus-frequency value in the dts
* Add the 8568MDS target to the Makefile
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit af1c2b84bf27c8565baddc82d1abb93700d10e2e
Author: David Updegraff <dave@cray.com>
Date: Fri Apr 20 14:34:48 2007 -0500
Add support for treating unknown PHYs as generic PHYs.
When bringing up u-boot on new boards, PHY support sometimes gets
neglected. Most PHYs don't really need any special support,
though. By adding a generic entry that always matches if nothing
else does, we can provide support for "unsupported" PHYs for the
tsec.
The generic PHY driver supports most PHYs, including gigabit.
Signed-off-by: David Updegraff <dave@cray.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit a75af9bfd8fff0499efdbb90601cec5a2afef117
Author: James Yang <James.Yang@freescale.com>
Date: Wed Feb 7 15:28:04 2007 -0600
Conditionalize 8641 Rev1.0 MCM workarounds
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f64702b7fc8f8df39d31add770df6e372f9e9ce3
Author: Timur Tabi <timur@freescale.com>
Date: Mon Apr 30 13:59:50 2007 -0500
Fix memory initialization on MPC8349E-mITX
Define CFG_DDR_SDRAM_CLK_CNTL for the MPC8349E-mITX and MPC8349E-mITX-GP.
This allows ddr->sdram_clk_cntl to be properly initialized. This is necessary
on some ITX boards, notably those with a revision 3.1 CPU.
Also change spd_sdram() in cpu/mpc83xx/spd_sdram.c to not write anything into
ddr->sdram_clk_cntl if CFG_DDR_SDRAM_CLK_CNTL is not defined.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Michael Benedict <MBenedict@twacs.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 54b2d434ae9d01787936f34fe1759cf3d7624ae3
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Mon Apr 30 15:26:21 2007 -0500
mpc83xx: replace elaborate boottime verbosity with 'clocks' command
and fix CPU: to align with Board: display text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit c1ab82669d9525998c34e802a12cad662723f22a
Author: James Yang <James.Yang@freescale.com>
Date: Fri Mar 16 13:02:53 2007 -0500
Rewrote picos_to_clk() to avoid rounding errors.
Clarified that conversion is to DRAM clocks rather than platform clocks.
Made function static to spd_sdram.c.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 8b39501d28754e72726ce7fb02310e56dbdf116a
Author: Stefan Roese <sr@denx.de>
Date: Sun Apr 29 14:13:01 2007 +0200
ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driver
Signed-off-by: Stefan Roese <sr@denx.de>
commit 864aa6a6a466fcb92bf32b1d7dba79cd709b52c9
Author: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Date: Sun Apr 29 14:01:54 2007 +0200
[PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot message
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up
message. Use PVR to distinguish between the two variants, and print proper CPU
information.
Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 5c5d3242935cf3543af01142627494434834cf98
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Apr 25 12:34:38 2007 -0500
mpc83xx: minor fixups for 8313rdb introduction
commit ada4d40091f6ed4a4f0040e08d20db21967e4a67
Author: Ladislav Michl <ladis@linux-mips.org>
Date: Wed Apr 25 16:01:26 2007 +0200
[PATCH] simplify silent console
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefan Roese <sr@denx.de>
commit 144876a380f5756f57412caf74c1d6dc201dd796
Author: Michal Simek <monstr@monstr.eu>
Date: Tue Apr 24 23:01:02 2007 +0200
[PATCH] MTD partition support, JFFS2 support
commit 37ed6cdd4159195bfad68d8a237f6adda8f482cb
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Tue Apr 24 14:03:45 2007 +0200
ppc4xx: setup 440EPx/GRx ZMII/RGMII bridge depending on PFC register content.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit 66ed6cca3f340f7a8a06d9272ae2ef8e96f0273d
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Apr 23 02:37:47 2007 -0500
Reworked 85xx speed detection code
Changed the code to read the registers and calculate the clock
rates, rather than using a "switch" statement.
Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 81f481ca708ed6a56bf9c410e3191dbad581c565
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Apr 23 02:24:28 2007 -0500
Enable 8544 support
* Add support to the Makefile
* Add 8544 configuration support to the tsec driver
* Add 8544 SVR numbers to processor.h
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 0d8c3a2096eaff8d7de89d45e9af4d4b0d4868fe
Author: Andy Fleming <afleming@freescale.com>
Date: Fri Feb 23 17:12:25 2007 -0600
Support 1G size on 8548
e500v2 and newer cores support 1G page sizes.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 45cef612cc601d2d1c890fbbd7cdc9609a189a46
Author: Andy Fleming <afleming@freescale.com>
Date: Fri Feb 23 17:11:16 2007 -0600
Changed BOOKE_PAGESZ_nGB to BOOKE_PAGESZ_nG
The other pagesz constants use one letter to specify order of
magnitude. Also change the one reference to it in mpc8548cds/init.S
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 1f9a318cea14272edd10d63739e2d326c90f430e
Author: Andy Fleming <afleming@freescale.com>
Date: Fri Feb 23 16:28:46 2007 -0600
Only set ddrioovcr for 8548 rev1.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 9343dbf85bc03033f2102d8e8543567c2c1ad2d2
Author: Andy Fleming <afleming@freescale.com>
Date: Sat Feb 24 01:16:45 2007 -0600
Tweak DDR ECC error counter
Enable single-bit error counter when memory was cleared by ddr controller.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 85e7c7a45e3dd9c7ce3e722352ba60f8df1a7a4b
Author: Timur Tabi <timur@freescale.com>
Date: Mon Feb 12 13:34:55 2007 -0600
85xx: write MAC address to mac-address and local-mac-address
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 03b81b48eec0ad249ec97a4ae16c36fa2e014ff4
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Apr 23 01:44:44 2007 -0500
Some 85xx cpu cleanups
* Cleaned up the TSR[WIS] clearing
* Cleaned up DMA initialization
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 151d5d992eab8c497b24c816c73dc1ad8bffb4eb
Author: Andy Fleming <afleming@freescale.com>
Date: Mon Apr 23 01:32:22 2007 -0500
Add cpu support for the 8544
Recognize new SVR values, and add a few register definitions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
commit 25d83d7f4ac65727182d8ddaf7ba42fa74cf65ae
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Apr 11 16:51:02 2007 -0500
Add MPC8544DS basic port board files.
Add board port under new board/freescale directory
structure and reuse existing PIXIS FPGA support there.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 0cde4b00fc7393b89f379d83a9d436dcb1334bfa
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Apr 11 16:50:57 2007 -0500
Add MPC8544DS main configuration file.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 362dd83077ac04c0296bca3e824ec2fb3d44d9d6
Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Date: Wed Dec 27 22:07:15 2006 +0300
Fix PCI I/O space mapping on Freescale MPC85x0ADS
The PCI I/O space mapping for Freescale MPC8540ADS board was broken by commit
52c7a68b8d587ebcf5a6b051b58b3d3ffa377ddc which failed to update the #define's
describing the local address window used for the PCI I/O space accesses -- fix
this and carry over the necessary changes into the MPC8560ADS code since the
PCI I/O space mapping was also broken for this board (by the earlier commit
087454609e47295443af793a282cddcd91a5f49c). Add the comments clarifying how
the PCI I/O space must be mapped to all the MPC85xx board config. headers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
board/mpc8540ads/init.S | 4 ++--
board/mpc8560ads/init.S | 4 ++--
include/configs/MPC8540ADS.h | 5 ++---
include/configs/MPC8541CDS.h | 2 +-
include/configs/MPC8548CDS.h | 2 +-
include/configs/MPC8560ADS.h | 8 ++++----
6 files changed, 12 insertions(+), 13 deletions(-)
commit 96629cbabdb727d4a5e62542deefc01d498db6dc
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Tue Dec 5 16:42:30 2006 +0800
u-boot: Fix e500 v2 core reset bug
The following patch fixes the e500 v2 core reset bug.
For e500 v2 core, a new reset control register is added to reset the
processor.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 63247a5acd58032e6cf33f525bc3923b467bac88
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Wed Dec 20 11:01:00 2006 +0800
u-boot: v2: Remove the fixed TLB and LAW entrynubmer
Remove the fixed TLB and LAW entry nubmer. Use actually TLB and LAW
entry number to control the loop. This can reduce the potential risk
for the 85xx processor increasing its TLB adn LAW entry number.
Signed-off-by: Swarthout Edward <swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 0b1934ba12fd408fcc3b8bd9f4b04864c42a42bf
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Mon Dec 18 17:01:04 2006 +0800
u-boot: Fix the 85xxcds tsec bug
Fix the 85xxcds tsec bug.
When enable PCI, tsec.o should be added to u-boot.lds to make tsec work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 7337b237ffc4aaf1b9467024fe472a880d852598
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Fri Dec 15 14:43:31 2006 +0800
u-boot: Fix CPU2 errata on MPC8548CDS board
This patch apply workaround of CPU2 errata on MPC8548CDS board.
Signed-off-by:Ebony Zhu <ebony.zhu@freescale.com>
commit 39b18c4f3e0b6d0dc00f4e68bad2da3766c85f09
Author: ebony.zhu@freescale.com <ebony.zhu@freescale.com>
Date: Mon Dec 18 16:25:15 2006 +0800
u-boot: Disables MPC8548CDS 2T_TIMING for DDR by default
This patch disables MPC8548CDS 2T_TIMING for DDR by default.
Signed-off-by:Ebony Zhu <ebony.zhu@freescale.com>
commit 41fb7e0f1ec9b91bdae2565bab5f2e3ee15039c7
Author: Zang Roy-r61911 <tie-fei.zang@freescale.com>
Date: Thu Dec 14 14:14:55 2006 +0800
u-boot: Enable PCI function and add PEX & rapidio memory map on MPC8548CDS board
Enable PCI function and add PEX & rapidio memory map on MPC8548CDS
board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 96b8a05432f346f36493535c85320b70ec9c7c1b
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:54:15 2007 -0500
mpc83xx: Add MPC8313ERDB support.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 49ea3b6eafe606285ae4d5c378026153dde53200
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:34:21 2007 -0500
mpc83xx: Add generic PCI setup code.
Board code can now request the generic setup code rather than having to
copy-and-paste it for themselves. Boards should be converted to use this
once they're tested with it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 7c98e5193e93df6b9b651851d54b638a61ebb0ea
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:34:19 2007 -0500
mpc83xx: Add 831x support to speed.c.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 0f253283a32d91e06844d7f87f9b33f4f4fbce8f
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:34:18 2007 -0500
mpc83xx: Add 831x support to global_data.h
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 95e7ef897e54591e615fc1b458b74c286fe1fb06
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:34:16 2007 -0500
mpc83xx: Change PVR_83xx to PVR_E300C1-3, and update checkcpu().
Rather than misleadingly define PVR_83xx as the specific type of 83xx
being built for, the PVR of each core revision is defined. checkcpu() now
prints the core that it detects, rather than aborting if it doesn't find
what it thinks it wants.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit a35b0c4950d84cf9e3a9e32b916135956d1ac636
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:34:15 2007 -0500
mpc83xx: Recognize SPR values for MPC8311 and MPC8313.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit d87c57b201b4572d16f1b642998faa00c9912b16
Author: Scott Wood <scottwood@freescale.com>
Date: Mon Apr 16 14:31:55 2007 -0500
mpc83xx: Add register definitions for MPC831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
commit 7fc4c71a143be8666d70803fb25ae60379c95622
Author: Stefan Roese <sr@denx.de>
Date: Mon Apr 23 15:39:59 2007 +0200
Fix file mode
Signed-off-by: Stefan Roese <sr@denx.de>
commit 38257988abfe74d459ca2ad748b109ca04e4efe1
Author: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Date: Mon Apr 23 15:30:39 2007 +0200
[PATCH] Avoid assigning PCI resources from zero address
If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE
core complains and IDE drivers fails to work. Also, assigning zero to a BAR
was illegal according to PCI 2.1 (the later revisions seem to have excluded the
sentence about "0" being considered an invalid address) -- so, use a reasonable
starting value of 0x1000 (that's what the most Linux archs are using).
Alternatively, one might have fixed the calls to pci_set_region() individually
(some code even seems to have taken care of this issue) but that would have
been a lot more work. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
commit afb903a2eb9436baa9270ccc0c27082d86497d89
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Mon Apr 23 14:00:11 2007 +0200
[patch] setenv(...) can delete environmentalvariables
update setenv() function so that entering a NULL value for the
variable's value will delete the environmental variable
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Acked-by: Stefan Roese <sr@denx.de>
commit 36f104e5caa747d568eff26b369565af57c2ffa6
Author: Mike Frysinger <vapier@gentoo.org>
Date: Mon Apr 23 13:54:24 2007 +0200
[patch] use unsigned char in smc91111 driver for mac
the v_mac variable in the smc91111 driver is declared as a signed char ...
this causes problems when one of the bytes in the MAC is "signed" like 0xE0
because when it gets printed out, you get a display like:
0xFFFFFFE0 and that's no good
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
commit d98c0885ad617fccf21e7c26ef8cb728fbfb2459
Author: Rodolfo Giometti <giometti@enneenne.com>
Date: Mon Apr 23 13:10:52 2007 +0200
USB: (Another) delay for crappy USB keys.
Some USB keys are slow in giving back an answer when the Root HUB
enables power lines.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
commit 323bfa8f436dc3bc57187c9b1488bc3146ff1522
Author: Stefan Roese <sr@denx.de>
Date: Mon Apr 23 12:00:22 2007 +0200
Remove BOARDLIBS usage completely
Signed-off-by: Stefan Roese <sr@denx.de>
commit 32556443840f127170e4baa8bdd5b567039f6c36
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Apr 21 21:07:22 2007 +0200
[PATCH] SystemACE support for Microblaze
commit 0643631aa1036cd746bf5d15f5a34bc7bc01ea4f
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Apr 21 21:02:40 2007 +0200
16bit read/write little endian
commit 9d1d6a34d26c5933bc097ce73c9348f95573cdd4
Author: Michal Simek <monstr@monstr.eu>
Date: Sat Apr 21 20:53:31 2007 +0200
Change ML401 parameters - Xilinx BSP
commit 2e343b9a57f32e1bd08c35c9976910333fb4e13d
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Feb 28 05:37:29 2007 -0600
mpc8641hpcn: Fix LAW and TLB setup to use the IO_PHYS #defines.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
commit 79cb47391eebef85acadb3f6961ef6c55cace6ac
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Fri Jan 19 10:42:37 2007 +0800
Enable LAWs for MPC8641 PCI-Ex2.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit bd7851ce1e1f140665b520026abf1042968b1102
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Apr 20 14:12:26 2007 -0500
mpc86xx; Write MAC address to mac-address and local-mac-address
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 7dbdf28b8bd855a8530dc3292e4982575a197060
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Apr 20 14:11:38 2007 -0500
mpc86xx: protect memcpy to bad address if a mac-address is missing from dt
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 14da5f7675bbb427c469e3f45006e027b6e21db9
Author: Wolfgang Denk <wd@denx.de>
Date: Fri Apr 20 17:43:28 2007 +0200
Cleanup compiler warnings, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 6923565db12af34fd5e02d354ee65a8c78ac460f
Author: Detlev Zundel <dzu@denx.de>
Date: Fri Apr 20 12:01:47 2007 +0200
Fix breakage of NC650 board with respect to nand support.
Signed-off-by: Detlev Zundel <dzu@denx.de>
commit 39f23cd90947639ac278a18ff277ec786b5ac167
Author: Domen Puncer <domen.puncer@telargo.com>
Date: Fri Apr 20 11:13:16 2007 +0200
[RFC PATCH] icecube/lite5200b: fix OF_TBCLK (timebase-frequency) calculation
G2 core reference manual says decrementer and time base
are decreasing/increasing once every 4 bus clock cycles.
Lets fix it, so time in Linux won't run twice as fast
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
commit 7651f8bdbba03bb0b4f241e2d2c4cb65b230bd56
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Thu Apr 19 23:14:39 2007 -0400
Fix serious pointer bug with bootm and reserve map.
What was suppose to be a stack variable was declared as a pointer,
overwriting random memory.
Also moved the libfdt.a requirement into the main Makefile. That is
The U-Boot Way.
commit d21686263574e95cb3e9e9b0496f968b1b897fdb
Author: Stefan Roese <sr@denx.de>
Date: Thu Apr 19 09:53:52 2007 +0200
ppc4xx: Fix chip select timing for SysACE access on AMCC Katmai
Previous versions used full wait states for the chip select #1 which
is connected to the Xilinix SystemACE controller on the AMCC Katmai
evaluation board. This leads to really slow access and therefore low
performance. This patch now sets up the chip select a lot faster
resulting in much better read/write performance of the Linux driver.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 37837828d89084879bee2f2b8c7c68d4695940df
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 17:49:29 2007 +0200
Clenaup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit fd094c6379e2ef8a4d0ceb5640b24cb0c8d04449
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 17:20:58 2007 +0200
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 2a26ec4732efd7a308d0bbc97714c1d75ef1173b
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 17:07:26 2007 +0200
Cleanup, update CHANGELOG
Sigend-off-by: Wolfgang Denk <wd@denx.de>
commit 5f6c732affea9647762d27a4617a2ae64c52dceb
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 16:17:46 2007 +0200
Update CHANGELOG
commit ad4eb555671d97f96dc56eab55103b1f86874b01
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 18 14:30:39 2007 +0200
MCC200 board: remove warning which is obsolete after PSoC firmware changes
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 3747a3f010b2b1442dec3e871c69788b6017aaae
Author: Domen Puncer <domen.puncer@telargo.com>
Date: Wed Apr 18 12:11:05 2007 +0200
[PATCH] icecube/lite5200b: document wakeup from low-power support
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
commit e673226ff9d6aa91b47ceac74b8c13770b06bb37
Author: Stefan Roese <sr@denx.de>
Date: Wed Apr 18 12:07:47 2007 +0200
ppc4xx: Update Acadia to not setup PLL when booting via bootstrap EEPROM
Signed-off-by: Stefan Roese <sr@denx.de>
commit 90e6f41cf09fc98f6ccb510e183d53ab8546cf2f
Author: Stefan Roese <sr@denx.de>
Date: Wed Apr 18 12:05:59 2007 +0200
ppc4xx: Add output for bootrom location to 405EZ ports
Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:
U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
Bootstrap Option E - Boot ROM Location EBC (32 bits)
16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board
Signed-off-by: Stefan Roese <sr@denx.de>
commit 9c00dfb0bf89c8c23e8af5b5bdf49cf66d769f85
Author: Peter Pearse <peter.pearse@arm.com>
Date: Tue Apr 17 13:30:33 2007 +0100
Move ppearse to ARM board list
Add Konstantin Kletschke for scb9328.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
commit d3832e8fe1b214ec62424eac36cfda9fc56d21b3
Author: Domen Puncer <domen.puncer@telargo.com>
Date: Mon Apr 16 14:00:13 2007 +0200
[PATCH] icecube/lite5200b: wakeup from low-power support
U-Boot part of Lite5200b low power mode support.
Puts SDRAM out of self-refresh and transfers control to
address saved at physical 0x0.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
commit f35a53fc7b0c79fcfe7bdc01163c4b34aaba1460
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sun Apr 15 13:54:26 2007 -0400
Fix the ft_cpu_setup() property settings.
Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.
commit c28abb9c614f65ce2096cc4a66fc886c77d0e5a4
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Apr 14 22:51:24 2007 -0400
Improve the bootm command for CONFIG_OF_LIBFDT
In bootm, create the "/chosen" node only if it doesn't already exist
(better matches the previous behavior).
Update for proper reserved memory map handling for initrd.
commit 3f9f08cf91c8a6949a5d78a18bd3d8df7b86d888
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Apr 14 22:46:41 2007 -0400
Add some utilities to manipulate the reserved memory map.
commit 8048cdd56f04a756eeea4951f402bf5cc33785db
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Apr 14 21:16:54 2007 +0200
Update CHANGELOG
commit 8e6875183cdca91c134408d119d4abcd48ef6856
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 18:56:46 2006 +0100
AVR32: Enable MMC support
Set up the portmux for the MMC interface and enable the MMC driver
along with support for DOS partitions, ext2 and FAT filesystems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit fc26c97bb6df41b4a95662c34054fe912387bf38
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Fri Jan 20 10:03:53 2006 +0100
Atmel MCI driver
Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.
The AT91 ARM-based CPUs use basically the same hardware, so it should
be possible to share this driver, but no effort has been made so far.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 05fdab1ef6a10d049a50021a86f1226f444d9b9f
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 18:55:37 2006 +0100
AVR32: Add clk and gpio infrastructure for mmci
Implement functions for configuring the mmci pins, as well as
functions for getting the clock rate of the mmci controller.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 7fac3f69e9f05c5e5326681976c35d129324c4de
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 18:53:56 2006 +0100
Enable partition support with MMC
Include implementations of init_part() and get_partition_info() when
CONFIG_MMC is set.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 9a24f477a1ed5bb0f74377c985d754ebbfa44872
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 17:14:30 2006 +0100
AVR32: Enable networking
Implement MACB initialization for AVR32 and ATSTK1000, and turn
everything on, including the MACB driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 5c1fe1ffffd1750a7e47e5a2e2cd600c00e4f009
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Fri Jan 20 10:03:34 2006 +0100
Atmel MACB ethernet driver
Driver for the Atmel MACB on-chip ethernet controller.
This driver has been tested on the ATSTK1000 board with a AT32AP7000
CPU. It should probably work on AT91SAM926x as well with some minor
modifications.
Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit b4ec9c2d43d894729bb633bfdbdfa95a962c1556
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 16:56:14 2006 +0100
AVR32: Add clk and gpio infrastructure for macb0 and macb1
Implement functions for configuring the macb0 and macb1 pins, as
well as functions for getting the clock rate of the various
busses the macb ethernet controllers are connected to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit d5acb95b16a0a74c643524342c3437e765426d05
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 15:39:15 2006 +0100
AVR32: Implement simple DMA memory allocator
Implement dma_alloc_coherent() which returns cache-aligned
uncacheable memory.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 91975b0fea773c9e681fea8cf3349669f27685ee
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 15:46:02 2006 +0100
Import <linux/mii.h> from the Linux kernel
Instead of creating yet another set of MII register definitions
in the macb driver, here's a complete set of definitions for everyone
to use.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 1b804b229556a4d862da93c0ec94e79419364b2c
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed Mar 21 19:47:36 2007 +0100
AVR32: Include more commands for ATSTK1000
Include the imi, imls and jffs commands sets by default on ATSTK1000.
Also define CONFIG_BOOTARGS to something more useful, define
CONFIG_BOOTCOMMAND and enable autoboot by default.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 9c0deb5ae3ea0189f2e08ac29ef1316f1fb8548d
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed Mar 21 19:44:48 2007 +0100
AVR32: Provide a definition of struct stat
Copy the definition of struct stat from the Linux kernel.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 12f099c08167a7a51aeee623bc16dafd0841271c
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Dec 17 14:46:06 2006 +0100
AVR32: Use initdram() instead of board_init_memories()
Conform to the "standard" interface and use initdram() instead of
board_init_memories() on AVR32. This enables us to get rid of the
sdram_size member of the global_data struct as well.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 1f4f2121c2685182eb87fa9a9b799d1917387a1c
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Mon Nov 20 15:53:10 2006 +0100
AVR32: Relocate u-boot to SDRAM
Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit df548d3c3e2bbc40258713167859ffc2ce99a900
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sun Nov 19 18:06:53 2006 +0100
AVR32: Resource management rewrite
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.
As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 03d1e1365796cd15d1726e8a51fd8b5be50b2fe9
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sat Nov 18 18:01:13 2006 +0100
AVR32: Clean up memory-map.h for at32ap7000
Convert spaces to tabs (must have missed this one last time around),
sort the entries by address and group them together by bus
connectivity.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 28c699ef69f4b6cdf252e4747b7b590028a88981
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sat Nov 18 17:32:31 2006 +0100
AVR32: Build position-independent u-boot
Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot
position independent. This will make relocation a lot easier.
-mno-init-got means that gcc shouldn't emit code to load the GOT
address into r6 in every function prologue. We do it once and for
all in the early startup assembly code, so enabling this option
makes u-boot a bit faster and smaller.
The assembly parts have always been position-independent, so no code
changes should be necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 5374b36de91d006d1df9536259fa9f66b01aa3aa
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sat Nov 18 17:24:31 2006 +0100
AVR32: Use avr32-linux- cross-compilation prefix by default
It doesn't really matter which toolchain you use to compile u-boot,
but the avr32-linux one is probably what most people have installed.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit c841beeddebece0039e724fb27f4d1a39ee1c6b6
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Sat Nov 18 17:15:30 2006 +0100
AVR32: Split start_u_boot into board_init_f and board_init_r
Split the avr32 initialization code into a function to run before
relocation, board_init_f and a function to run after relocation,
board_init_r. For now, board_init_f simply calls board_init_r
at the end.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 37403005cfe6bb13964d450f6a48a0b0f2f7017e
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Sat Apr 14 05:26:48 2007 +0200
[Fix] Set the LED status register on the UC101 for the LXT971 PHY.
clear the Display after reset.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 7882751c78b7ecabfd49b0eff8de27661c71f16c
Author: Denis Peter <d.peter@mpl.ch>
Date: Fri Apr 13 09:13:33 2007 +0200
[PATCH] Fix bugs in cmd_ide.c and cmd_scsi.c
Fix bug introduced by "Fix get_partition_info() parameter error in all
other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented
to use diskboot or scsiboot form another device than 0.
Signed-off-by: Denis Peter <d.peter@mpl.ch>
commit 0b94504d22e70f537c17a0d38c87edb6e370977d
Author: Greg Lopp <lopp@pobox.com>
Date: Fri Apr 13 08:02:24 2007 +0200
[PATCH] Fix use of "void *" for block dev read/write buffer pointers
Signed-of-by: Greg Lopp <lopp@pobox.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
commit 6fbf261f8df294e589cfadebebe5468e3c0f29e9
Author: Xie Xiaobo <r63061@freescale.com>
Date: Fri Mar 9 19:08:25 2007 +0800
Fix two bugs for MPC83xx DDR2 controller SPD Init
There are a few bugs in the cpu/mpc83xx/spd_sdram.c
the first bug is that the picos_to_clk routine introduces a huge
rounding error in 83xx.
the second bug is that the mode register write recovery field is
tWR-1, not tWR >> 1.
commit 2ad3aba01d37b72e7c957b07e102fccd64fe6d13
Author: Jeffrey Mann <mannj@embeddedplanet.com>
Date: Thu Apr 12 14:15:59 2007 +0200
ppc4xx: Fix i2c divisor calcularion for PPC4xx
This patch fixes changes the i2c_init(...) function to use the function
get_OPB_freq() rather than calculating the OPB speed by
sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
specific per processor. The prior method was not and so was calculating
the wrong speed for some PPC4xx processors.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6c9ba919375db977aaad9146bf320c7afd07ae7a
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 11 17:25:01 2007 +0200
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 51056dd9863e6a1bc363afbbe1775c58cd967418
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 11 17:22:55 2007 +0200
Update for SC3 board
* Make IDE timeout configurable through ide_reset_timeout variable.
* Use Newline as "password" string
* Use just a single partition in NAND flash
commit 3d98b85800c80dc68227c8f10bf5c93456d6d054
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Mon Jan 22 12:37:30 2007 -0600
Add PIXIS FPGA support for MPC8641HPCN board.
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 64dbbd40c58349b64f43fd33dbb5ca0adb67d642
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Fri Apr 6 14:19:43 2007 -0400
Moved fdt command support code to fdt_support.c
...in preparation for improving the bootm command's handling of fdt blobs.
Also cleaned up some coding sloppiness.
commit 6679f9299534e488a171a9bb8f9bb891de247aab
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Fri Apr 6 14:17:14 2007 -0400
libfdt: Make fdt_check_header() public
Changed _fdt_check_header() to fdt_check_header() and made it part of
the interface - it is a useful routine.
Also did some asthetics cleanup to the include files (headers).
commit c0707ce65677650b5ceab0500ee50ae5168afef2
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:34:06 2007 +0800
[Blackfin][PATCH] Kill off a bunch of common local prototypes
commit 7b7e30aa64bb6657a1bfd32fdbdbfeb561e6a48d
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:33:04 2007 +0800
[Blackfin][PATCH] Fix dynamic CPLB generation issue
commit 0445e3a264251d75b1be45ef713c70726a2952f0
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:31:47 2007 +0800
[Blackfin][PATCH] minior cleanup
commit 155fd766573981090e638b493d5857562151862e
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:31:18 2007 +0800
[Blackfin][PATCH] Fix copyright and update license
commit 9fd437bbd75d282f899e1da50be20a2bf38450bc
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:30:25 2007 +0800
[Blackfin][PATCH] Add BF537 EMAC driver initialization
commit 889256e8604e0c68db1d866d720894dffede9df6
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:29:55 2007 +0800
[Blackfin][PATCH] call real the system synchronize instruction
commit e0df1c921b788289564e4c1ee7120a6a9cd3ab05
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:29:17 2007 +0800
[Blackfin][PATCH] remove asm/page.h as we do not actually use/want any of these definitions nor does any other arch include it
commit dfeeab2cd680df047e68e723b246adf6f33bb556
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Thu Apr 5 18:28:34 2007 +0800
[Blackfin][PATCH]: fix flash unaligned copy issue
commit 443feb740584e406efa203af909fe2926608e8d5
Author: Igor Marnat <marny@rambler.ru>
Date: Wed Mar 21 09:55:01 2007 +0300
Update usage of 'nc' in README.NetConsole
Added information about usage of NetConsole on systems where the -l and -p
switches are mutually exclusive.
Signed-off-by: Igor Marnat <marny@rambler.ru>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit 31c98a88228021b314c89ebb8104fb6473da4471
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 4 02:09:30 2007 +0200
Minor coding style cleanup.
commit 94abd7c0583ebe01e799b25f451201deeaab550d
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Apr 4 01:49:15 2007 +0200
Minor cleanup.
commit 822af351ad2babc7d99033361a5fcacd30f6bc78
Author: Rodolfo Giometti <giometti@enneenne.com>
Date: Tue Apr 3 14:27:18 2007 +0200
Support for the Philips ISP116x HCD (Host Controller Driver)
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
commit edf5851be6c17c031d4f71dd5b0a12040b7c50c8
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Apr 3 14:27:08 2007 +0200
USB: cleanup monahans usb support. Remove dead code.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
commit a65c5768e5537530bd1780af3d3fddc3113a163c
Author: Stefan Roese <sr@denx.de>
Date: Mon Apr 2 10:09:30 2007 +0200
ppc4xx: Change SysACE address on Katmai
With this new base address of the Xilinx SystemACE controller
the Linux driver will be easier to adapt, since it can now be
mapped via the "normal" ioremap() call.
Signed-off-by: Stefan Roese <sr@denx.de>
commit aea03c4e8c3a21ce43d3faf48a6e6d474c8bdf73
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 14:30:53 2007 -0400
Fix some minor whitespace violations.
commit 213bf8c822de8eecaf69860684469cdaba2e9e6a
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 12:23:51 2007 -0400
Add a flattened device tree (fdt) command (2 of 2)
Modifications to the existing code to support the new fdt command.
commit 781e09ee6e3e3e392ab362c1f0ef1068adc76e3e
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 12:22:10 2007 -0400
Add a flattened device tree (fdt) command (1 of 2)
The fdt command uses David Gibson's libfdt library to manipulate as well
as print the flattened device tree. This patch is the new command,
the second part is the modifications to the existing code.
commit 3af0d587d93e0be5f96e1b30fa41e662f8b0803e
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 12:13:43 2007 -0400
libfdt: Enhanced and published fdt_next_tag()
Enhanced the formerly private function _fdt_next_tag() to allow stepping
through the tree, used to produce a human-readable dump, and made
it part of the published interface.
Also added some comments.
commit fa3a74cec73dfd06a5ae35a9a3368200273aaa71
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 12:05:39 2007 -0400
libfdt: Customizations for use by u-boot.
Changes to David Gibson's original source to fit into u-boot's
environment. No functionality changes.
commit 35748177c64a4a83a00057e93bb33e40278a2a96
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 12:00:56 2007 -0400
libfdt: Import libfdt source (2 of 2)
This adds the applicable libfdt source files (unmodified) and a README
to explain where the source came from.
commit 7cd5da0fe877e7171a4cdd44880bce783132871a
Author: Gerald Van Baren <vanbaren@cideas.com>
Date: Sat Mar 31 11:59:59 2007 -0400
libfdt: Import libfdt source (1 of 2)
This adds the applicable libfdt source files (unmodified) and a README
to explain where the source came from.
commit da6ebc1bc082cbe3b6bbde079cafe09f7ebbad4b
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 31 13:16:23 2007 +0200
ppc4xx: Update Katmai bootstrap command
Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB
is selected.
Signed-off-by: Stefan Roese <sr@denx.de>
commit cabee756a6532986729477c3cc1ea16ef8517ad2
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 31 13:15:06 2007 +0200
ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
Additional RAM information is now printed upon powerup, like
DDR2 frequency and CAS latency.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 60723803431ac75cad085690789e433d5ab9174e
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 31 08:48:36 2007 +0200
ppc4xx: Change Yucca config file to support ECC
With the updated 44x DDR2 driver the Yucca board now supports
ECC generation and checking.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 490e5730c674b20d708b783a2c5ffd7208f83873
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 31 08:47:34 2007 +0200
ppc4xx: Fix "bootstrap" command for Katmai board
The board specific "bootstrap" command is now fixed and can
be used for the AMCC Katmai board to configure different
CPU/PLB/OPB frequencies.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 94f54703c3a776ec23e427ca2a16e0a79a5d50c1
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 31 08:46:08 2007 +0200
ppc4xx: Update 44x_spd_ddr2 code (440SP/440SPe)
Fix a bug in the auto calibration routine. This driver now runs
more reliable with the tested modules. It's also tested with
167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 342cd097be1e7affe82f42ab3da220959a699e64
Author: Michal Simek <monstr@monstr.eu>
Date: Fri Mar 30 22:52:09 2007 +0200
[PATCH] Clean include dependence
commit 6f934210fb293fde2cfb4251c6d96fdc58b6a906
Author: Michal Simek <monstr@monstr.eu>
Date: Fri Mar 30 22:42:45 2007 +0200
[CLEAN] Remove inefficient Suzaku code
commit 430f1b0f9a670c2f13eaa52e66a10db96dd3647d
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 28 15:03:16 2007 +0200
Merge some AMCC make targets to keep the top-level Makefile smaller
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0c75c9d84307a9f1cbe1ff0c4d8937ee3a96475e
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 28 14:52:12 2007 +0200
i2c: Enable "old" i2c commands even when CONFIG_I2C_CMD_TREE is defined
The "old" i2c commands (iprobe, imd...) are now compiled in again,
even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
config option.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 5da048adf44bea5e3b94080d02903c2e3fe7aa4a
Author: Michal Simek <monstr@monstr.eu>
Date: Tue Mar 27 00:32:16 2007 +0200
PATCH: Resolve GPL license problem
commit ae00bb4b2944dc64a485ed72a19754b11af7c223
Author: Rodolfo Giometti <giometti@enneenne.com>
Date: Mon Mar 26 12:03:36 2007 +0200
PXA: pxa27x USB OHCI support
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
commit ae79f60677c208326535647dcbd5c3ec40dbcb0b
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon Mar 26 11:21:05 2007 +0200
USB: remove the S3C24X0_merge #define, which was introduced while
merging OHCI drivers.
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
commit 1798049522f594013aea29457d46794298c6ae15
Author: Michal Simek <root@monstr.eu>
Date: Mon Mar 26 01:39:07 2007 +0200
Support for XUPV2P board
Reset support
BSP autoconfig support
commit 0d974d5297349504a2ddfa09314be573b5df320a
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 24 15:57:09 2007 +0100
[PATCH] Add 4xx GPIO functions
This patch adds some 4xx GPIO functions. It also moves some of the
common code and defines into a common 4xx GPIO header file.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2db633658bbf366ab0c8dad7a0727e1fb2ae6b11
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 24 15:55:58 2007 +0100
[PATCH] Small Sequoia cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3cb86f3e40d2a80356177434a99f75bc8baa9caf
Author: Stefan Roese <sr@denx.de>
Date: Sat Mar 24 15:45:34 2007 +0100
[PATCH] Clean up 40EZ/Acadia support
This patch cleans up all the open issue of the preliminary
Acadia support.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6eb1df835191d8ce4b81d5af40fa8e0fbe78e997
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Dec 12 11:02:20 2006 -0600
Fix 8641HPCN problem with ld version 2.16
(Dot outside sections problem).
This fix is in the spirit of 807d5d7319330e336ab34a5623c5e0d73b87d540.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 9964a4dd0d4ef5a037febaebf1aa494b1a72991c
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Thu Dec 7 10:35:55 2006 -0600
Set Rev 2.x 86xx PIC in mixed mode.
Prevent false interrupt from hanging Linux as MSR[EE] is set
to enable interrupts by changing the PIC out of the default
pass through mode into mixed mode.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 5a58a73ceb0a4059c42ef64cedbc1a45e0aaa00e
Author: Jason Jin <jason.jin@freescale.com>
Date: Thu Dec 7 10:32:35 2006 -0600
Add flash cmd function to 8641HPCN ramboot
Also fixes some commmand for 8641 HPCN ramboot case.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2ccceacc04b009d923afb7c26189ba2f8a2a5d46
Author: Ed Swarthout <ed.swarthout@freescale.com>
Date: Thu Dec 7 10:34:14 2006 -0600
Add support for 8641 Rev 2 silicon.
Without this patch, I am unable to get to the prompt on rev 2 silicon.
Only set ddrioovcr for rev1.
Signed-off-by: Ed Swarthout<ed.swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 44ba464b99001f8bd1c456a1e9d59726252f707a
Author: Wolfgang Denk <wd@denx.de>
Date: Thu Mar 22 00:13:12 2007 +0100
Code cleanup / re-insert previous Copyright entries.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 2a8dfe08359a1b663418b2faa1da1d7bce34d302
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Mar 21 23:26:15 2007 +0100
Code cleanup. Update CHANGELOG
commit e6615ecf4eaf4dd52696934aed8f5c6474cfd286
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 21 14:54:29 2007 +0100
ppc4xx: Fix file mode of include/configs/acadia.h
Signed-off-by: Stefan Roese <sr@denx.de>
commit d5f4614c9350d9333e575100fb250aab774d0258
Author: Markus Klotzbuecher <mk@denx.de>
Date: Wed Mar 21 14:41:46 2007 +0100
SPC1920: fix small clock routing bug
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
commit 16c0cc1c82081a493ab87c51980b28336ce1bce8
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 21 13:39:57 2007 +0100
[PATCH] Add AMCC Acadia (405EZ) eval board support
This patch adds support for the new AMCC Acadia eval board.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
commit e01bd218b00af73499331a1a701625a852cd286f
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 21 13:38:59 2007 +0100
[PATCH] Add AMCC PPC405EZ support
This patch adds support for the new AMCC 405EZ PPC. It is in
preparation for the AMCC Acadia board support.
Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 07e82cb2e284a893df6693f2a1337ab2c47bf6a1
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Wed Mar 21 08:45:17 2007 +0100
[PATCH] TQM8272: dont change the bits given from the HRCW
for the SIUMCR and BCR Register.
Fix the calculation for the EEprom Size
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 654589873dbafcf104dff133ce0d03a4506e9cc3
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Tue Mar 20 18:16:24 2007 +0800
[Blackfin][PATCH] Add BF561 EZKIT board support
commit a6154fd1cfd020f6da8527e0365b1020a11a71d0
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 19 22:55:58 2007 +0800
[Blackfin][PATCH] minor cleanup
commit 389b6bb50f745bf5038ce030300d8a8512e96f79
Author: Wolfgang Denk <wd@denx.de>
Date: Mon Mar 19 13:10:08 2007 +0100
Remove obsoleted POST files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 8e709bbb2636b5670a8f2b575e138eb1f55773f6
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 19 01:26:11 2007 +0800
[PATCH] Add flash chip M29W320ET/B support
commit 26bf7deca364a5b33f39e8f14ddd3f4081345015
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 19 01:24:52 2007 +0800
[Blackfin][PATCH] Add BF537 stamp board support
commit 8423e5e31a7235d05a482627315fb11d49c17bd7
Author: Stefan Roese <sr@denx.de>
Date: Fri Mar 16 21:11:42 2007 +0100
[PATCH] Use dynamic SDRAM TLB setup on AMCC Ebony eval board
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).
Signed-off-by: Stefan Roese <sr@denx.de>
commit 76d1466f918b881cda2d259254761e73885093c2
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Tue Mar 13 13:38:05 2007 +0100
[PATCH] renamed environment variable 'addcon' to 'addcons' for PCI405
boards in terms of unification.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit a7090b993d3d4d2221ac3f33e6cb1d1b2ccc6bf0
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Mar 13 16:05:55 2007 +0100
Make SC3 board build with 'make O='; use 'addcons' consistently
(SC3 and Jupiter used to use 'addcon' instead).
Signed-off-by: Wolfgang Denk wd@denx.de
commit 8502e30a28e492c756ea2d7df0ace026388fce4b
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Tue Mar 13 09:40:59 2007 +0100
[PATCH] update board config for jupiter Board:
added Hush Shell,
CONFIG_CMDLINE_EDITING,
CFG_ENV_ADDR_REDUND activated
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 0d93de11449390a5984b0236c3612e50f6dbb7e8
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 12 12:11:55 2007 +0800
[Blackfin][PATCH] minor cleanup
commit bfa5754a58477ac917d21527cd0f079d87cf188e
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 12 01:42:06 2007 +0800
[Blackfin][PATCH] Fix BUILD_DIR option of MAKEALL building issue
commit 8440bb14581a294375c34b91b42512f9753d1130
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Mon Mar 12 00:25:14 2007 +0800
[Blackfin][PATCH] code cleanup
commit cfc67116a706fd18b8f6a9c11a16753c5626d689
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Mar 11 13:48:24 2007 +0100
[Microblaze][PATCH] part 2
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
commit 76316a318de91f6184e7c22a10e02d275ade2441
Author: Michal Simek <monstr@monstr.eu>
Date: Sun Mar 11 13:42:58 2007 +0100
[Microblaze][PATCH]
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
commit 8db13d63157811c839d15a313d9f2d2f5fd10af3
Author: Aubrey Li <aubrey.adi@gmail.com>
Date: Sat Mar 10 23:49:29 2007 +0800
[Blackfin][PATCH] code cleanup
commit ef26a08fef928b7bc11ae2c109e638dc3a016d91
Author: Aubrey.Li <aubrey.adi@gmail.com>
Date: Fri Mar 9 13:40:56 2007 +0800
[Blackfin][PATCH-2/2] Common files changed to support bf533 platform
commit 3f0606ad0b5639f7f22848fe5b4574e754d0470f
Author: Aubrey.Li <aubrey.adi@gmail.com>
Date: Fri Mar 9 13:38:44 2007 +0800
[Blackfin]PATCH-1/2]: Remove obsolete blackfin port and add bf533 platform support
commit 992423ab43c2bcf6b704853bd00af77450915e20
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 8 23:00:08 2007 +0100
ppc4xx: Fix file mode of sequoia.c
Signed-off-by: Stefan Roese <sr@denx.de>
commit eb92f613556800f7483666db09d9a237ad911d4a
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Mar 8 22:52:51 2007 +0100
Minor cleanup.
commit 8ce16f55c7b9752af3d8bed84521aec5337e2de1
Author: John Otken john@softadvances.com <john@softadvances.com>
Date: Thu Mar 8 09:39:48 2007 -0600
ppc4xx: Clear Sequoia/Rainier security engine reset bits
Signed-off-by: John Otken john@softadvances.com <john@softadvances.com>
commit 650a330dd2539130c8c324791e2f9f75aed79d4e
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Thu Mar 8 16:26:52 2007 +0100
[PATCH] I2C: add some more SPD eeprom decoding for DDR2 modules
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit d9fc703246840c4b268debf48c334ba55c597dc0
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Thu Mar 8 16:25:47 2007 +0100
[PATCH] I2C: disable flat i2c commands when CONFIG_I2C_CMD_TREE is defined
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit ced5b9029043397348cdc88e0cfcd6b1f629250b
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Thu Mar 8 16:23:11 2007 +0100
[PATCH] 4xx: allow CONFIG_I2C_CMD_TREE without CONFIG_I2C_MULTI_BUS
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit d8a8ea5c476d37006fc7f85b7f903142795c8b14
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Thu Mar 8 16:20:32 2007 +0100
[PATCH] I2C: Add missing default CFG_SPD_BUS_NUM
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit f9fc6a5852a6335840882fa2111925010eea1abe
Author: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Date: Wed Mar 7 15:32:01 2007 +0100
fixed ethernet phy configuration for plu405 board
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
commit 769104c9356594deb2092e204a39c05b33202d6c
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Mar 8 21:49:27 2007 +0100
Minor cleanup
commit 00cdb4ce5e1b42248e7e6522ad0da3421b988afa
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 8 10:13:16 2007 +0100
[PATCH] Update AMCC Luan 440SP eval board support
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2f5df47351910a2936c7741cf111855829200943
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 8 10:10:18 2007 +0100
[PATCH] Update AMCC Yucca 440SPe eval board support
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2721a68a9ea91f1e494649ce68b2577261f578e2
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 8 10:07:18 2007 +0100
ppc4xx: Small AMCC Katmai 440SPe update
Signed-off-by: Stefan Roese <sr@denx.de>
commit df294497479b1dca6dd86318b2a912f72fede0df
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 8 10:06:09 2007 +0100
ppc4xx: Update 440SP/440SPe DDR SPD setup code to support 440SP
Signed-off-by: Stefan Roese <sr@denx.de>
commit 83853178bd36bca6f0f8f1331476620c84a587fc
Author: Ed Swarthout <Ed.Swarthout@freescale.com>
Date: Wed Mar 7 12:14:50 2007 -0600
net - Support ping reply when processing net-loop
Add ICMP_ECHO_REQUEST packet support by responding with a ICMP_ECHO_REPLY.
This permits the ping command to test the phy interface when the phy
is put in loopback mode (typically by setting register 0 bit 14).
It also allows the port to respond to an external ping when u-boot is
processing some other net command (such as tftp). This is useful when
tftp appears to hang.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit fa1aef15bcd47736687be1af544506e90fba545d
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 7 16:43:00 2007 +0100
[PATCH] Use dynamic SDRAM TLB setup on AMCC Ocotea eval board
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).
Signed-off-by: Stefan Roese <sr@denx.de>
commit e2ebe696818939e2b974628be9c921ea3fe9de13
Author: Stefan Roese <sr@denx.de>
Date: Wed Mar 7 16:39:36 2007 +0100
[PATCH] Fix AMCC 44x SPD SDRAM init code to support 2 DIMM's
This patch fixes a problem that occurs when 2 DIMM's are
used. This problem was first spotted and fixed by Gerald Jackson
<gerald.jackson@reaonixsecurity.com> but this patch fixes the
problem in a little more clever way.
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
As this feature is new to the "old" 44x SPD DDR driver, it
has to be enabled via the CONFIG_PROG_SDRAM_TLB define.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 39218433983417b9df087976a79e3f80dd5e83d6
Author: Wolfgang Denk <wd@denx.de>
Date: Wed Mar 7 16:33:44 2007 +0100
UC101: fix compiler warnings
commit 8d7e2732221bc2d64df14f700c64c23e0a4c3dce
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Mar 7 16:19:46 2007 +0100
HMI1001: fix build error, cleanup compiler warnings.
commit ad5bb451ade552c44bef9119d907929ebc2c126f
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Mar 6 18:08:43 2007 +0100
Restructure POST directory to support of other CPUs, boards, etc.
commit a5284efd125967675b2e9c6ef7b95832268ad360
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Mar 6 18:01:47 2007 +0100
Fix HOSTARCH handling.
Patch by Mike Frysinger, Mar 05 2007
commit 07b7b0037aac5102939917d7cbe561b5c0d5aa44
Author: Stefan Roese <sr@denx.de>
Date: Tue Mar 6 07:47:04 2007 +0100
[PATCH] Speed optimization of AMCC Sequoia/Rainier DDR2 setup
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.
For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 647d3c3eed0da1d1505eecabe0b0fab96f956e68
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sun Mar 4 01:36:05 2007 +0100
Some code cleanup.
commit 781e026c8aa6f7e9eb5f0e72cc4d20971219b148
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Feb 28 00:02:04 2007 -0600
mpc83xx: fix implicit declaration of function 'ft_get_prop' warnings
(cherry picked from c5bf13b02284c3204a723566a9bab700e5059659 commit)
commit 4feab4de7bfc2cb2fed36ad76f93c3a69659bbaf
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue Feb 27 23:51:42 2007 -0600
mpc83xx: Fix config of Arbiter, System Priority, and Clock Mode
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit d51b3cf371cd441030460ef19d36b2924c361b1a
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Feb 22 20:06:57 2007 -0600
mpc83xx: update [local-]mac-address properties on UEC based devices
8360 and 832x weren't updating their [local-]mac-address
properties. This patch fixes that.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 61f4f912acbe60776c5e00df1ec94094ce672957
Author: Timur Tabi <timur@freescale.com>
Date: Tue Feb 13 10:41:42 2007 -0600
mpc83xx: write MAC address to mac-address and local-mac-address
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, this patch
updates ftp_cpu_setup() to write the MAC address to mac-address if it exists.
This function already updates local-mac-address.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 22d71a71f57fd5d38b27ac3848e50d790360a598
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Feb 27 18:41:08 2007 -0600
mpc83xx: add command line editing by default
commit 3fc0bd159103b536e1c54c6f4457a09b3aba66ca
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Feb 14 19:50:53 2007 -0600
mpc83xx: Disable G1TXCLK, G2TXCLK h/w buffers
Disable G1TXCLK, G2TXCLK h/w buffers. This patch
fixes a networking timeout issue with MPC8360EA (Rev.2) PBs.
Verified on Rev. 1.1, Rev. 1.2, and Rev. 2.0 boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Emilian Medve <Emilian.Medve@freescale.com>
commit d61853cf2472e0b8bcbd131461a93d1c49ff0c1f
Author: Xie Xiaobo <r63061@freescale.com>
Date: Wed Feb 14 18:27:17 2007 +0800
mpc83xx: Add DDR2 controller fixed/SPD Init for MPC83xx
The code supply fixed and SPD initialization for MPC83xx DDR2 Controller.
it pass DDR/DDR2 compliance tests.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
commit b110f40bd180c6b560276589beedf753e97c46ce
Author: Xie Xiaobo <r63061@freescale.com>
Date: Wed Feb 14 18:27:06 2007 +0800
mpc83xx: Add the cpu specific code for MPC8360E rev2.0 MDS
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
commit 8d172c0f0d85998a256a95b7459a5403a30380ed
Author: Xie Xiaobo <r63061@freescale.com>
Date: Wed Feb 14 18:26:44 2007 +0800
mpc83xx: Add the cpu and board specific code for MPC8349E rev3.1 MDS
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
commit f6f5f709e5c8e4564c4dfeecfdf2279244f9c83b
Author: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Date: Wed Jan 31 11:04:19 2007 +0100
mpc83xx: Fix empty i2c reads/writes in fsl_i2c.c
Fix empty i2c reads/writes, i2c_write(0x50, 0x00, 0, NULL, 0)
which is used to se if an slave will ACK after receiving its address.
Correct i2c probing to use this method as the old method could upset
a slave as it wrote a data byte to it.
Add a small delay in i2c_init() to let the controller
shutdown any ongoing I2C activity.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
commit 7a78f148d6a7298e4fface680dc7eacd877b1aba
Author: Timur Tabi <timur@freescale.com>
Date: Wed Jan 31 15:54:29 2007 -0600
mpc83xx: Add support for the MPC8349E-mITX-GP
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit fab16807adad350f618024350c6950165c247c72
Author: Timur Tabi <timur@freescale.com>
Date: Wed Jan 31 15:54:20 2007 -0600
mpc83xx: Delete sdram_init() for MPC8349E-mITX
There is no SDRAM on any of the 8349 ITX variants, so function sdram_init()
never does anything. This patch deletes it.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit a87c856eb411b9365937d0d4b9c21e46adbe1c14
Author: Dave Liu <daveliu@freescale.com>
Date: Fri Jan 19 10:43:26 2007 +0800
mpc83xx: Fix the LAW1/3 bug
The patch solves the alignment problem of the local bus access windows to
render accessible the memory bank and PHY registers of UPC 1 (starting at
0xf801 0000). What we actually did was to adjust the sizes of the bus
access windows so that the base address alignment requirement would be met.
Signed-off-by: Chereji Marian <marian.chereji@freescale.com>
Signed-off-by: Gridish Shlomi <gridish@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit 97c4b397dce236a7318b304667bf89e59d08b17c
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Jan 30 16:15:31 2007 -0600
mpc83xx: don't hang if watchdog configured on 8360, 832x
don't hang if watchdog configured on 8360, 832x
The watchdog programming model is the same across all 83xx devices;
make the code reflect that.
commit b70047478570e371ce7223be342ce98afea0f7d6
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Jan 30 16:15:21 2007 -0600
mpc83xx: protect memcpy to bad address if a local-mac-address is missing from dt
protect memcpy to bad address if a local-mac-address is missing from dt
commit 6752ed088c75c26a89b70c46b7326a4cd6015f29
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Jan 30 16:15:04 2007 -0600
mpc83xx: make 8360 default environment fdt be 8360 (not 8349)
make 8360 default environment fdt be 8360 (not 8349)
commit a28899c910024a0226331df07207b1038c300c93
Author: Emilian Medve <Emilian.Medve@freescale.com>
Date: Tue Jan 30 16:14:50 2007 -0600
mpc83xx: Fix alternating tx error / tx buffer not ready bug in QE UEC
The problem is not gcc4 but the code itself. The BD_STATUS() macro can't
be used for busy-waiting since it strips the 'volatile' property from
the bd variable. gcc3 was working by pure luck.
This is a follow on patch to "Fix the UEC driver bug of QE"
commit 3e78a31cfe3d3022f46f67eb88e1281d5cc2eb89
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue Jan 30 14:08:30 2007 -0600
mpc83xx: Replace CONFIG_MPC8349 and use CONFIG_MPC834X instead
The code that is ifdef'd with CONFIG_MPC8349 is actually applicable to all
MPC834X class processors. Change the protections from CONFIG_MPC8349 to
CONFIG_MPC834X so they are more generic.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit ae246dc6c1937c291014eadd90b6d48c438c7cb0
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Jan 25 13:40:55 2007 -0600
mpc83xx: add MPC832XEMDS and sbc8349 to MAKEALL
commit 4decd84e8f04279c5cfff7f8e907465ef8d8a3fb
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Jan 24 17:18:37 2007 -0600
mpc83xx: sort Makefile targets
reordered targets alphabetically
commit 91e25769771c1164ed63ffca0add49f934ae3343
Author: Paul Gortmaker <paul.gortmaker@windriver.com>
Date: Tue Jan 16 11:38:14 2007 -0500
mpc83xx: U-Boot support for Wind River SBC8349
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
commit 05031db456ab227f3e3752f37b9b812b65bb83ad
Author: Sam Song <samsongshu@yahoo.com.cn>
Date: Thu Dec 14 19:03:21 2006 +0800
mpc83xx: Remove a redundant semicolon in mpc8349itx.c
A redundant semicolon existed in mpc8349itx.c
should be removed.
Signed-off-by: Sam Song <samsongshu@yahoo.com.cn>
commit f35f358241c549be3f75cfe2eaa642914275b7ba
Author: Jerry Van Baren <gerald.vanbaren@comcast.net>
Date: Wed Dec 6 21:23:55 2006 -0500
mpc83xx: Put the version (and magic) after the HRCW.
Put the version (and magic) after the HRCW. This puts it in a fixed
location in flash, not at the start of flash but as close as we can get.
Signed-off-by: Jerry Van Baren <vanbaren@cideas.com>
commit 48aecd969171a6e99a55fae04933857787f9a5bd
Author: Dave Liu <r63238@freescale.com>
Date: Thu Dec 7 21:14:51 2006 +0800
mpc83xx: Add the MPC832XEMDS board readme
Add the MPC832XEMDS board readme
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit 24c3aca3f1358b113d3215adb5433b156e99f72b
Author: Dave Liu <r63238@freescale.com>
Date: Thu Dec 7 21:13:15 2006 +0800
mpc83xx: Add support for the MPC832XEMDS board
This patch supports DUART, ETH3/4 and PCI etc.
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit e080313c32322e15ab5a18eb896a252858c57284
Author: Dave Liu <r63238@freescale.com>
Date: Thu Dec 7 21:11:58 2006 +0800
mpc83xx: streamline the 83xx immr head file
For better format and style, I streamlined the 83xx head files,
including immap_83xx.h and mpc83xx.h. In the old head files, 1)
duplicated macro definition appear in the both files; 2) the structure
of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The
macro definition put inside the each structure. So, I cleaned up the
structure of QE immr from immap_83xx.h, deleted the duplicated stuff and
moved the macro definition to mpc83xx.h, Just like MPC8260.
CHANGELOG
*streamline the 83xx immr head file
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit ddd02492f43db5408f5ab9f823b0ba5796e28ef0
Author: Dave Liu <r63238@freescale.com>
Date: Wed Dec 6 11:38:17 2006 +0800
mpc83xx: Fix the UEC driver bug of QE
The patch prevents the GCC tool chain from striping useful code for
optimization. It will make UEC ethernet driver workable, Otherwise the
UEC will fail in tx when you are using gcc4.x. but the driver can work
when using gcc3.4.3.
CHANGELOG
*Prevent the GCC from striping code for optimization, Otherwise the UEC
will tx failed when you are using gcc4.x.
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit ba58e4c9a9a917ce795dd16d4ec8d515f9f7aa35
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 1 21:11:36 2007 +0100
[PATCH] Update AMCC Katmai 440SPe eval board support
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 8c12045a3b06c5b6675d3fe02fbc9f545988129a
Author: Stefan Roese <sr@denx.de>
Date: Thu Mar 1 07:03:25 2007 +0100
[PATCH] I2C: Add missing default CFG_RTC_BUS_NUM & CFG_DTT_BUS_NUM
Signed-off-by: Stefan Roese <sr@denx.de>
commit ccbc7036648e465697ca298ba51e0e76dda352a0
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Feb 28 01:28:53 2007 +0100
SC3: fix typo in default environment
commit e344568b1b46af85ec32d815586f91bc115d6223
Author: Sergei Poselenov <sposelenov@emcraft.com>
Date: Tue Feb 27 20:15:30 2007 +0300
MCC200: Fixes for update procedure
- fix logic error in image type handling
- make sure file system images (cramfs etc.) get stored in flash
with image header stripped so they can be mounted through MTD
commit 743571145b37182757d4e688a77860b36ee77573
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Feb 27 14:26:04 2007 +0100
Minor code cleanup.
commit 638dd1458bbdc2a55d4b9e25c5c4e1f838a5dc72
Author: Sergei Poselenov <sposelenov@emcraft.com>
Date: Tue Feb 27 12:40:16 2007 +0300
MCC200 update - add LCD Progress Indicator
commit 6c7cac8c4fce0ea2bf8e15ed8658d87974155b44
Author: Stefan Roese <sr@denx.de>
Date: Thu Feb 22 07:43:34 2007 +0100
[PATCH] get_dev() now unconditionally uses manual relocation
Since the relocation fix is not included yet and we're not sure how
it will be added, this patch removes code that required relocation
to be fixed for now.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 8274ec0bd01d2feb2c7f095eba78d42ea009798b
Author: Stefan Roese <sr@denx.de>
Date: Thu Feb 22 07:40:23 2007 +0100
[PATCH] Change systemace driver to select 8 & 16bit mode
As suggested by Grant Likely this patch enables the Xilinx SystemACE
driver to select 8 or 16bit mode upon startup.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 3a197b2fe49d6fa03978e60af2394efe9c70b527
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Wed Feb 21 16:52:31 2007 +0100
[PATCH v3] Add sync to ensure flash_write_cmd is fully finished
Some CPUs like PPC, BLACKFIN need sync() to ensure cfi flash write command
is fully finished. The sync() is defined in each CPU's io.h file. For
those CPUs which do not need sync for now, a dummy sync() is defined in
their io.h as well.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit da04995c7dc6772013a9a0dc5c767f190c402478
Author: Stefan Roese <sr@denx.de>
Date: Wed Feb 21 13:44:34 2007 +0100
[PATCH] Fix problem in systemace driver (ace_writew instead of ace_write)
Signed-off-by: Stefan Roese <sr@denx.de>
commit 751bb57107d78978ae08e697c3deba816f5be091
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 13:21:57 2007 +0100
[PATCH] Fix relocation problem with "new" get_dev() function
This patch enables the "new" get_dev() function for block devices
introduced by Grant Likely to be used on systems that still suffer
from the relocation problems (manual relocation neede because of
problems with linker script).
Hopefully we can resolve this relocation issue soon for all platform
so we don't need this additional code anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
commit d93e2212f962668b3dce091ff5edc33f2347fe37
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 13:17:42 2007 +0100
[PATCH] Update SystemACE driver for 16bit access
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
commit 874bb7b88fe9b4648e1288a387af2e31014a72f3
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 13:15:40 2007 +0100
[PATCH] Clean up Katmai (440SPe) linker script
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4745acaa1a603b67f6b9b7970365ebadd7d6586f
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 10:57:08 2007 +0100
[PATCH] Add support for the AMCC Katmai (440SPe) eval board
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0dc018ece13effc689e47479ea9ebf1c98a507f5
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 10:51:26 2007 +0100
[PATCH] I2C: Add support for multiple I2C busses for RTC & DTT
This patch switches to the desired I2C bus when the date/dtt
commands are called. This can be configured using the
CFG_RTC_BUS_NUM and/or CFG_DTT_BUS_NUM defines.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4037ed3b63923cfcec27f784a89057c3cbabcedb
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 10:43:34 2007 +0100
[PATCH] PPC4xx: Add 440SP(e) DDR2 SPD DIMM support
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 36d830c9830379045f5daa9f542ac1c990c70068
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 10:35:42 2007 +0100
[PATCH] PPC4xx: Split 4xx SPD SDRAM init routines into 2 files
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Signed-off-by: Stefan Roese <sr@denx.de>
commit 79b2d0bb2eae09602448f7a7cb56530d2f31e6c6
Author: Stefan Roese <sr@denx.de>
Date: Tue Feb 20 10:27:08 2007 +0100
[PATCH] PPC4xx: Add support for multiple I2C busses
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Signed-off-by: Stefan Roese <sr@denx.de>
commit eb867a76238fb38e952c37871b16d0d7fd61c95f
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:45 2007 +0100
[PATCH 9_9] Use "void *" not "unsigned long *" for block dev read_write buffer pointers
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 53758fa20e935cc87eeb0519ed365df753a6f289
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:38 2007 +0100
[PATCH 8_9] Add block_write hook to block_dev_desc_t
Preparation for future patches which support block device writing
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f4852ebe6ca946a509667eb68be42026f837be76
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:31 2007 +0100
[PATCH 7_9] Replace ace_readw_ace_writeb functions with macros
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 3a8ce9af6fcb5744a7851b4440c07688acc40844
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:23 2007 +0100
[PATCH 6_9] Move common_cmd_ace.c to drivers_systemace.c
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 984618f3e7794c783ec8d1511e74c6ee2d69bfe4
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:16 2007 +0100
[PATCH 5_9] Whitespace fixup on common_cmd_ace.c (using Lindent)
This patch is in preparation of additional changes to the sysace driver.
May as well take this opportunity to fixup the inconsistent whitespace since
this file is about to undergo major changes anyway.
There are zero functional changes in this patch. It only cleans up the
the whitespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 80ba981d940471fe7e539e64fa3d2bd80002beda
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:07 2007 +0100
[PATCH 4_4] Remove local implementation of isprint() in ft_build.c
isprint is already defined in ctype.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit c95c4280d751ca078c2ff58228d2f2b44ccf0600
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:05:00 2007 +0100
[PATCH 3_9] Move buffer print code from md command to common function
Printing a buffer is a darn useful thing. Move the buffer print code
into print_buffer() in lib_generic/
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 99b0f0fd3fbf2572ae1a7723dd90cffc8e85130a
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:04:52 2007 +0100
[PATCH 2_4] Use config.h, not xparameters.h, for xilinx targets
Change the xilinx device drivers and board code to include config.h
instead of xparameters.h directly. config.h always includes the
correct xparameters file. This change reduces the posibility of
including the wrong file when adding a new xilinx board port
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 735dd97b1b20e777d059c7b389fe9d70cd3f80c7
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Feb 20 09:04:34 2007 +0100
[PATCH 1_4] Merge common get_dev() routines for block devices
Each of the filesystem drivers duplicate the get_dev routine. This change
merges them into a single function in part.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit f5fcc3c20b65554e98a165542c36ee0c610a2d81
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Feb 19 23:09:51 2007 +0100
MCC200: Software Updater: allow both "ramdisk" and "filesystem" types
as root file system images.
commit 489c696ae7211218961d159e43e722d74c36fcbc
Author: Sergei Poselenov <sposelenov@emcraft.com>
Date: Wed Feb 14 14:30:28 2007 +0300
MCC200: Extensions to Software Update Mechanism
Update / extend Software Update Mechanism for MCC200 board:
- Add support for rootfs image added. The environment variables
"rootfs_st" and "rootfs_nd" can be used to override the default
values of the image start and end.
- Remove excessive key check code.
- Code cleanup.
commit 4be23a12f23f1372634edc3215137b09768b7949
Author: Stefan Roese <sr@denx.de>
Date: Mon Feb 19 08:23:15 2007 +0100
[PATCH] Update Sequoia EBC configuration (NOR FLASH)
As spotted by Matthias Fuchs, the READY input should not be
enabled for the NOR FLASH on the Sequoia board.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2605e90bf676d48123afe5719a846d2b52b24aac
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Feb 16 07:57:42 2007 +0100
[PATCH] Added support for the jupiter board.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 497d012e5be0194e1084073d0081eb1a844796b2
Author: Gary Jennejohn <garyj@pollux.denx.de>
Date: Mon Feb 12 13:11:50 2007 +0100
LPC2292: patch from Siemens.
commit b0b1a920aebead0d44146e73676ae9d80fffc8e2
Author: Stefan Roese <sr@denx.de>
Date: Sat Feb 10 08:49:31 2007 +0100
[PATCH] Add missing p3mx.h file to repository (ups)
Signed-off-by: Stefan Roese <sr@denx.de>
commit 53d4a4983fb9b3ae5f7b2f10c599aca2b1b4034a
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Fri Feb 9 10:45:42 2007 +0100
[Motion-PRO] Preliminary support for the Motion-PRO board.
commit 5a753f98c6a01bd1c61a9a3f95e8329a35f62994
Author: Stefan Roese <sr@denx.de>
Date: Wed Feb 7 16:51:08 2007 +0100
[PATCH] Update some AMCC 4xx board config files (set initrd_high)
Some boards that can have more than 768MBytes of SDRAM need to
set "initrd_high", so that the initrd can be accessed by the
Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 7372ca68227930d03cffa548310524cad5b96733
Author: Stefan Roese <sr@denx.de>
Date: Fri Feb 2 12:44:22 2007 +0100
[PATCH] Correctly display PCI arbiter en-/disabled on some 4xx boards
Previously the strapping DCR/SDR was read to determine if the internal PCI
arbiter is enabled or not. This strapping bit can be overridden, so now
the current status is read from the correct DCR/SDR register.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2aa54f651a42d198673318f07a20c89a43e4d197
Author: Stefan Roese <sr@denx.de>
Date: Fri Feb 2 12:42:08 2007 +0100
[PATCH] Change configuration output of Sycamore, Yellowstone & Rainier
Signed-off-by: Stefan Roese <sr@denx.de>
commit 23744d6b5bf17592eb6a0ef4f318f6089f55993b
Author: Stefan Roese <sr@denx.de>
Date: Thu Feb 1 13:22:41 2007 +0100
[PATCH] Remove PCI-PNP configuration from Sequoia/Rainier config file
When PCI PNP is enabled the pci pnp configuration routine is called
which sets the PCI_CACHE_SIZE_LINE to 8. This seems to generate some
problems with some PCI cards. For now disable the PCI PNP configuration.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 2902fadade3be7659467e8d074048c6b7068f5c0
Author: Stefan Roese <sr@denx.de>
Date: Wed Jan 31 16:56:10 2007 +0100
[PATCH] Update 440EPx/440GRx cpu detection
Signed-off-by: Stefan Roese <sr@denx.de>
commit d5ea287b02a6945c3977410e364a879dd1a555c8
Author: Stefan Roese <sr@denx.de>
Date: Wed Jan 31 16:38:04 2007 +0100
[PATCH] Update esd cpci5200 files
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
commit 8b7d1f0ab7d7c4fe3160bbf74a7e9690d9f3a3ab
Author: Stefan Roese <sr@denx.de>
Date: Wed Jan 31 16:37:34 2007 +0100
[PATCH] Add support for esd mecp5200 board
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
commit 71a4e5fda8b60044ab9f46069fa1cfa26bdd07ff
Author: Stefan Roese <sr@denx.de>
Date: Wed Jan 31 12:38:50 2007 +0100
[PATCH] Remove unneccessary yellowstone board config file
Signed-off-by: Stefan Roese <sr@denx.de>
commit e802594b6fa1b166308820c276b96dc0d7cc731c
Author: Stefan Roese <sr@denx.de>
Date: Tue Jan 30 17:06:10 2007 +0100
[PATCH] Update Sequoia (440EPx) config file
The config file now handles the 2nd target, the Rainier (440GRx)
evaluation board better. Additionally the PPC input clock was
adjusted to match the correct value of 33.0 MHz.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 700200c67e73b83751418abe7815840dca8fd6cb
Author: Stefan Roese <sr@denx.de>
Date: Tue Jan 30 17:04:19 2007 +0100
[PATCH] Merge Yosemite & Yellowstone board ports
Now the AMCC eval boards Yosemite (440EP) and Yellowstone (440GR)
share one config file and all board specific files. This way we
don't have to maintain two different sets of files for nearly
identical boards.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1bbf5eae322f5f1f6427ecc3ac13a0cb7dba8ad6
Author: Stefan Roese <sr@denx.de>
Date: Tue Jan 30 15:01:49 2007 +0100
[PATCH] Update Prodrive SCPU (PDNB3 variant) board
SCPU doesn't use redundant environment in flash.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6304430ed642ea8fa15c9e5af965ac2e033eec45
Author: Stefan Roese <sr@denx.de>
Date: Tue Jan 30 12:51:07 2007 +0100
[PATCH] alpr: Update alpr board config file
Signed-off-by: Stefan Roese <sr@denx.de>
commit f8db84f132b1e335f20f96138a1f09ed97b08664
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Jan 30 00:50:40 2007 +0100
LPC2292 SODIMM port coding style cleanup.
commit 6bd2447ee47ee23c18d2b3c7ccd5a20f7626f5b3
Author: Gary Jennejohn <garyj@pollux.denx.de>
Date: Wed Jan 24 12:16:56 2007 +0100
Add port for the lpc2292sodimm evaluation board from EmbeddedArtists
commit 2daf046ba627f85f44195815778140039636244e
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue Jan 23 17:22:06 2007 +0100
[iDMR] Add MTD and JFFS2 support, also add default partition definition.
commit f7db33101fbc9c8f0a10738ce87034875a17aeb9
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue Jan 23 14:21:14 2007 +0100
[iDMR] Flash driver on initialisation write-protects some sectors,
currently sectors 0-3. Sector 3 does not need to be protected, though
(U-boot occupies sectors 0-1 and the environment sector 2). This commit
fixes this, i.e., only sectors 0-2 are protected.
commit 0ed47bb119cd2c4c16edb2548789148f9e6dc9de
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue Jan 23 14:11:22 2007 +0100
[iDMR] Using MII-related commands on iDRM board doesn't work now (e.g.,
"mii device" results in "Unexpected exception"). Fixing this properly
requires some clean-up in the FEC drivers infrastructure for ColdFire, so
this commit disables MII commads for now.
commit 363d1d8f9c99b63daef81f5985cab3fc00edde5c
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Tue Jan 23 13:25:22 2007 +0100
[ColdFire MCF5271 family] Add CPU detection based on the value of Chip
Identification Register (CIR).
commit fdef388758506765d4d6a7155c8f1584c63ff581
Author: roy zang <tie-fei.zang@freescale.com>
Date: Mon Jan 22 13:19:21 2007 +0800
use CFG_WRITE_SWAPPED_DATA define instead of define CFG_FLASH_CFI_SWAP
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
commit a4012396645533aef218354eeba754dff0deace8
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Fri Jan 19 23:08:39 2007 +0100
Minor code cleanup.
commit f539b7ba7d7ef6dd187c8209609001cb1cd95e39
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Jan 19 19:57:10 2007 +0100
[PATCH] SC3 board: added CFG_CMD_AUTOSCRIPT.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit d0b6e14087ddd8789f224a48e1d33f2a5df4d167
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Fri Jan 19 18:05:26 2007 +0100
[PATCH] CFI: define CFG_WRITE_SWAPPED_DATA for the CFI-Flash driver
if you must swap the bytes between reading/writing.
(Needed for the SC3 board)
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 9d8d5a5bfb64768f29a0cb47fc37cd6f4c40e276
Author: Stefan Roese <sr@denx.de>
Date: Thu Jan 18 16:05:47 2007 +0100
[PATCH] Add support for Prodrive SCPU (PDNB3 variant) board
Signed-off-by: Stefan Roese <sr@denx.de>
commit 0057d758e3e874cbe7f24745d0cce8c1cb6c207e
Author: Stefan Roese <sr@denx.de>
Date: Thu Jan 18 11:54:52 2007 +0100
[PATCH] Update Prodrive P3Mx support
Signed-off-by: Stefan Roese <sr@denx.de>
commit 34167a36c29ee946b727465db5c014746a08e978
Author: Stefan Roese <sr@denx.de>
Date: Thu Jan 18 11:48:10 2007 +0100
[PATCH] Add missing Taishan config file
Signed-off-by: Stefan Roese <sr@denx.de>
commit cb4820725e9fc409c5cbc8e83054a6ed522d2111
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Thu Jan 18 11:28:51 2007 +0100
[PATCH] Fix: Compilerwarnings for SC3 board.
The EBC Configuration Register is now by CFG_EBC_CFG definable
Added JFFS2 support for the SC3 board.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 5fb692cae57d1710c8f52a427cf7f39a37383fcd
Author: Stefan Roese <sr@denx.de>
Date: Thu Jan 18 10:25:34 2007 +0100
[PATCH] Add support for AMCC Taishan PPC440GX eval board
Signed-off-by: Stefan Roese <sr@denx.de>
commit 6d3e0107235aa0e6a6dcb77f9884497280bf85ad
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Jan 16 18:30:50 2007 +0100
Raname solidcard3 into sc3; add redundant env for sc3
commit 1bbbbdd20fcec9933697000dcf55ff7972622596
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Jan 16 12:46:35 2007 +0100
Update default environment for Solidcard3
commit 5a5c56986a9ccf71642c8b6374eb18487b15fecd
Author: Stefan Roese <sr@denx.de>
Date: Mon Jan 15 09:46:29 2007 +0100
[PATCH] Fix 440SPe rev B detection from previous patch
Signed-off-by: Stefan Roese <sr@denx.de>
commit a443d31410c571ee8f970da819a44d698fdd6b1f
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Sun Jan 14 13:35:31 2007 +0100
[FIX] correct I2C Writes for the LM81 Sensor.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 0bba5452835f19a61204edcda3a58112fd8e2208
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sat Jan 13 11:17:10 2007 +0100
Undo commit 3033ebb2: reset command does not take any arguments
Haiying Wang's modification to the reset command was broken, undo it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 95981778cff0038fd9941044d6a3eda810e33258
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 13 08:01:03 2007 +0100
[PATCH] Update 440SP(e) cpu revisions
Also display enabled/disabled RAID 6 support for 440SP/440SPe PPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 77ddc5b9afb325262fd88752ba430a1dded1f0c7
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 13 07:59:56 2007 +0100
[PATCH] Update Yellowstone (440GR) to display board rev and PCI bus speed
Now the board revision and the current PCI bus speed are printed after
the board message.
Also the EBC initialising is now done via defines in the board config
file.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 36adff362c2c0141ff8a810d42a7e478f779130f
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 13 07:59:19 2007 +0100
[PATCH] Update Yosemite (440EP) to display board rev and PCI bus speed
Now the board revision and the current PCI bus speed are printed after
the board message.
Also the EBC initialising is now done via defines in the board config
file.
Signed-off-by: Stefan Roese <sr@denx.de>
commit e0b9ea8c8a294de6a5350ae638879d24b5b709d6
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 13 07:57:51 2007 +0100
[PATCH] Update Sequoia (440EPx) to display board rev and PCI bus speed
Now the board revision and the current PCI bus speed are printed after
the board message.
Signed-off-by: Stefan Roese <sr@denx.de>
commit ca43ba18e910206ef8063e4b22d282630bff3fd2
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Thu Jan 11 15:44:44 2007 +0100
Added support for the SOLIDCARD III board from Eurodesign
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 6abaee42621c07e81a2cd189ad4368b5e8c50280
Author: Reinhard Thies <Reinhard.Thies@web.de>
Date: Wed Jan 10 14:41:14 2007 +0100
Adjusted default environment for cam5200 board.
commit bab5a90d4ccc1a46a8127b867fa59028cc623ad9
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Jan 10 15:35:52 2007 +0100
Update CHANGELOG
commit 787fa15860a57833e50bd30555079a9cd4e519b8
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Jan 10 01:28:39 2007 +0100
Fix auto_update for MCC200 board.
The invocation of do_auto_update() is moved to the end of the
misc_init_r() function, after the flash mappings have been
initialized. Please find attached a patch that implements that
change.
Also correct the decoding of the keypad status. With this update, the
key that will trigger the update is Column 2, Row 2.
commit d9384de2f571046e71081bae22b49e3d5ca2e3d5
Author: Marian Balakowicz <m8@semihalf.com>
Date: Wed Jan 10 00:26:15 2007 +0100
CAM5200 flash driver modifications:
- use CFI driver (replaces custom flash driver) for main 'cam5200' target
- add second build target 'cam5200_niosflash' which still uses custom driver
commit 67fea022fa957f59653b5238c7496f80a6b70432
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Jan 9 16:02:48 2007 +0100
SPC1920: cleanup memory contoller setup
commit 8fc2102faa23593c80381437c09f7745a14deb40
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Jan 9 14:57:14 2007 +0100
Fix the cpu speed setup to work with all boards.
commit 9295acb77481cf099ef9b40e1fa2d145b3c7490c
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Jan 9 14:57:13 2007 +0100
SPC1920: add support for the FM18L08 Ramtron FRAM
commit 38ccd2fdf3364a53fe80e9b365303ecdafc9e223
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Jan 9 14:57:13 2007 +0100
SPC1920: update the HPI register addresses to work with the second
generation of hardware
commit 5921e5313fc3eadd42770c2b99badd7fae5ecf1e
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:13 2007 +0100
Miscellanious spc1920 related cleanups
commit e4c2d37adc8bb1bf69dcf600cbc6c75f916a6120
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue Jan 9 14:57:12 2007 +0100
SPC1920 GO/NOGO led should be set to color red in U-Boot
commit 0be62728aac459ba268d6d752ed49ec0e2bc7348
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:12 2007 +0100
Add support for the DS3231 RTC
commit 8139567b60d678584b05f0718a681f2047c5e14f
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:11 2007 +0100
SMC1 uses external CLK4 instead of BRG on spc1920
commit d8d9de1a02fbd880b613d607143d1f57342affc7
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:10 2007 +0100
Update the SPC1920 CMB PLD driver
commit 3f34f869162750e5e999fd140f884f5de952bcfe
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:10 2007 +0100
Add / enable I2C support on the spc1920 board
commit d28707dbce1e9ac2017ad051da4133bf22b4204f
Author: Markus Klotzbuecher <mk@creamnet.de>
Date: Tue Jan 9 14:57:10 2007 +0100
Add support for the tms320671x host port interface (HPI)
commit f4eb54529bb3664c3a562e488b460fe075f79d67
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sun Jan 7 00:13:11 2007 +0100
Prepare for release 1.2.0
commit f07ae7a9daef27a3d0213a4f3fe39d5342173c02
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 6 15:58:09 2007 +0100
[PATCH] 44x: Fix problem with DDR controller setup (refresh rate)
This patch fixes a problem with an incorrect setup for the refresh
timer of the 44x DDR controller in the file cpu/ppc4xx/sdram.c
Signed-off-by: Stefan Roese <sr@denx.de>
commit f16c1da9577f06c5fc08651a4065537407de4635
Author: Stefan Roese <sr@denx.de>
Date: Sat Jan 6 15:56:13 2007 +0100
[PATCH] Update ALPR board files
This update brings the ALPR board support to the newest version.
It also fixes a problem with the NAND driver.
Signed-off-by: Stefan Roese <sr@denx.de>
commit cd1d937f90250a32988c37b2b4af8364d25de8ed
Author: Stefan Roese <sr@denx.de>
Date: Fri Jan 5 11:46:05 2007 +0100
[PATCH] nand: Fix problem with oobsize calculation
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Signed-off-by: Stefan Roese <sr@denx.de>
commit a78bc443ae5a4a8ba87590587d5e35bf5a787b2e
Author: Stefan Roese <sr@denx.de>
Date: Fri Jan 5 10:40:36 2007 +0100
[PATCH] Clear PLB4A0_ACR[WRP] on Sequoia (440EPx)
This fix will make the MAL burst disabling patch for the Linux
EMAC driver obsolete.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 023889838282b6237b401664f22dd22dfba2c066
Author: Stefan Roese <sr@denx.de>
Date: Fri Jan 5 10:38:05 2007 +0100
[PATCH] Add DDR2 optimization code for Sequoia (440EPx) board
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
commit cce4acbb68398634b8d011ed7bb0d12269c84230
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Thu Dec 28 19:08:21 2006 +0100
Few V38B changes:
- fix a typo in V38B config file
- move watchdog initialisation earlier in the boot process
- add "wdt=off" to default kernel command line (disables kernel watchdog)
commit 92eb729bad876725aeea908d2addba0800620840
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Dec 27 01:26:13 2006 +0100
Fix bug in adaption of Stefano Babic's CFI driver patch.
commit 9c0f42ecfe25f7ffce8ec7a815f03864d723ffe3
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sun Dec 24 01:42:57 2006 +0100
Minor code cleanup.
commit d784fdb05900ada3686d5778783e1fb328e9fb66
Author: Stefano Babic <sbabic@denx.de>
Date: Tue Dec 12 00:22:42 2006 +0100
Fix cfi failure with Spansion Flash (Spansion Flash Devices have a different offset to go into CFI mode)
commit 1b3c360c235dc684ec06c2d5f183f0a282ce45e2
Author: Stefan Roese <sr@denx.de>
Date: Fri Dec 22 14:29:40 2006 +0100
[PATCH] Fix sequoia flash autodetection (finally correct)
Now 32MByte and 64MByte FLASH is know to work and other
configurations should work too.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 82e5236a8b719543643fd26d5827938ab2b94818
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Fri Dec 22 10:30:26 2006 +0100
Minor code cleanup; update CHANGELOG.
commit fa23044564091f05d9695beb7b5b9a931e7f41a4
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Thu Dec 21 17:17:02 2006 +0100
Added support for the TQM8272 board from TQ
Signed-off-by: Heiko Schocher <hs@denx.de>
commit 6dedf3d49dd14c3bf541c8ecee7ffaac5f0e1d6c
Author: Heiko Schocher <hs@pollux.denx.de>
Date: Thu Dec 21 16:14:48 2006 +0100
[PATCH] Add support for the UC101 board from MAN.
Signed-off-by: Heiko Schocher <hs@denx.de>
commit c84bad0ef60e7055ab0bd49b93069509cecc382a
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Dec 20 00:29:43 2006 +0100
Fix to make the baudrate changes immediate for the MCF52x2 family.
commit daa6e418bcc0c717752e8de939c213c790286096
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Dec 20 00:27:32 2006 +0100
Preliminary support for the iDMR board (ColdFire).
commit cdb97a6678826f85e7c69eae6a1c113d034c9b10
Author: Andrei Safronov <safronov@pollux.denx.de>
Date: Fri Dec 8 16:23:08 2006 +0100
automatic update mechanism
commit 9d27b3a0685ff99fc477983f315c04d49f657a8a
Author: roy zang <tie-fei.zang@freescale.com>
Date: Mon Dec 4 17:56:59 2006 +0800
Slight code clean up.
Add comments, delete duplicate define and remove spaces.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 4dbcd69e3e2776ea334590d5768e3692c5fae5c1
Author: roy zang <tie-fei.zang@freescale.com>
Date: Mon Dec 4 17:54:21 2006 +0800
Introduce PLL_CFG[0:4] table for processor 7448/7447A/7455/7457. The original
multiplier table can not refect the real PLL clock behavior of these
processors. Please refer to the hardware specification for detailed
information of the corresponding processors.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 4efe20c9579011d9987f62ed7d35ee8cdc1cf0e0
Author: roy zang <tie-fei.zang@freescale.com>
Date: Mon Dec 4 14:46:23 2006 +0800
Remove the static MAC address, ip address, server ip, netmask and
gateway ip for network setting.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 6f12c61cf31ed73d72ddfcfc712a854a3a177aaf
Author: roy zang <tie-fei.zang@freescale.com>
Date: Mon Dec 4 14:33:08 2006 +0800
Remove the duplicate memory test code for mpc744ihpc2 board.
If a memory test is needed, please use the functions in
post/memory.c or memtest command.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit c9c1eeed7dd193fa65fb194654132040d49d4d3a
Author: roy zang <tie-fei.zang@freescale.com>
Date: Fri Dec 1 19:01:25 2006 +0800
Fix the exception occuring in RAM table search issue.
The original search_one_table() function code can only processes the search
for the exception occurring in FLASH/ROM, because the exception and fixup
table usually locate in FLASH. If the exception address is also in
FLASH, it will be OK.
If the exception occurs in RAM, after the u-boot relocation, a
relocation offset should be added.
clean up the code in cpu/74xx_7xx/cpu.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit ee311214e0d216f904feea269599d0934bf71f23
Author: roy zang <tie-fei.zang@freescale.com>
Date: Fri Dec 1 11:47:36 2006 +0800
Clean up the code according to codestyle:
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
commit dd520bf314c7add4183c5191692180f576f96b60
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Nov 30 18:02:20 2006 +0100
Code cleanup.
commit 8d9a8610b8256331132227e9e6585c6bd5742787
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Nov 30 01:54:07 2006 +0100
Code cleanup. Update CHANGELOG.
commit 726e90aacf0b1ecb0e7055be574622fbe3e450ba
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Wed Nov 29 16:23:42 2006 +0100
[PATCH] [MPC52xx] Use IPB bus frequency for SOC peripherals
The soc node of the mpc52xx needs to be loaded with the IPB bus frequency,
not the XLB frequency.
This patch depends on the previous patches for MPC52xx device tree support
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
commit 1eac2a71417b6675b11aace72102a2e7fde8f5c6
Author: Stefan Roese <sr@denx.de>
Date: Wed Nov 29 15:42:37 2006 +0100
[PATCH] Add support for Prodrive P3M750 & P3M7448 (P3Mx) boards
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1bdd46832aeb569f5e04b1f20f64318525b6525a
Author: Stefan Roese <sr@denx.de>
Date: Wed Nov 29 12:53:15 2006 +0100
[PATCH] common/cmd_elf.c: Enable loadaddr as parameter in bootvx command
In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4e26f1074c3ac1bd8fd094f0dc4a1c4a0b15a592
Author: Stefan Roese <sr@denx.de>
Date: Wed Nov 29 12:03:57 2006 +0100
[PATCH] include/ppc440.h minor error affecting interrupts
Fixed include/ppc440.c for UIC address Bug
Corrects bug affecting the addresses for the universal interrupt
controller UIC2 and UIC3 on the PPC440 Epx, GRx, and SPE chips.
Signed-off-by: Jeff Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1939d969443ccf316cab2bf32ab1027d4db5ba1a
Author: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Date: Tue Nov 28 16:17:27 2006 -0600
Make fsl-i2c not conflict with SOFT I2C
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 14198bf768fdc958e3c1afd2404e5262208e98d7
Author: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Date: Tue Nov 28 16:17:18 2006 -0600
Fix I2C master address initialization.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit cf3d045e51ca8dcc6cf759827140861d6ac25c04
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Nov 28 23:31:19 2006 -0600
Assign maintainers for mpc8349emds and mpc8360emds
Dave for mpc8360emds, and me for mpc8349emds.
commit 1aa934c81b77f2080d3ca4b226eab67b17a33961
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Tue Nov 28 23:28:33 2006 -0600
Eliminate gcc 4 'used uninitialized' warnings in drivers/qe/uccf.c
give initial values for reg_num, shift, p_cmxucr in ucc_set_clk_src
since they are passed by reference to ucc_get_cmxucr_reg and assigned.
commit e857a5bdb3954b896c0920cb9d8d2b1b9c107ce5
Author: Timur Tabi <timur@freescale.com>
Date: Tue Nov 28 12:09:35 2006 -0600
mpc83xx: Miscellaneous code style fixes
Implement various code style fixes and similar changes.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit e59581c56ab5d6e0207ddac3b2c1d55cb36ec706
Author: Stefan Roese <sr@denx.de>
Date: Tue Nov 28 17:55:49 2006 +0100
[PATCH] Enable the IceCube/lite5200 variants to pass a device tree to Linux.
This patch adds the code and configuration necessary to boot with an
arch/powerpc Linux kernel.
Signed-off-by: Grant Likely <grant.likely@gmail.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
commit e732faec95a83cb468b4850ae807c8301dde8f6a
Author: Stefan Roese <sr@denx.de>
Date: Tue Nov 28 16:09:24 2006 +0100
[PATCH] PPC4xx: 440SP Rev. C detection added
Signed-off-by: Stefan Roese <sr@denx.de>
commit e7f3e9ff01fbd7fa72eb42a9675fbed6bc4736b0
Author: Stefan Roese <sr@denx.de>
Date: Tue Nov 28 11:04:45 2006 +0100
[PATCH] nand: Fix patch merge problem
Signed-off-by: Stefan Roese <sr@denx.de>
commit 58e3b14c18ed3288ceef8d086946dbf3df64ccf2
Author: Stefan Roese <sr@denx.de>
Date: Tue Nov 28 11:04:45 2006 +0100
[PATCH] nand: Fix patch merge problem
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4f4b602ec7524a032bdf3c6d28c7f525a4a67eaa
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Nov 27 22:53:53 2006 +0100
Update CHANGELOG
commit f6e495f54cdb8fe340b9c03deab40ad746d52fae
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 17:43:25 2006 +0100
[PATCH] 4xx_enet.c: Correct the setting of zmiifer register
Patch below corrects the setting of the zmiifer register, it was
overwritting the register rather than ORing the settings.
Signed-off-by: Neil Wilson <NWilson@airspan.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit d1a72545296800b7e219f93104ad5836f0003d66
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 17:34:10 2006 +0100
[PATCH] Select NAND embedded environment from board configuration
The current NAND Bootloader setup forces the environment
variables to be in line with the bootloader. This change
enables the configuration to be made in the board include
file instead so that it can be individually enabled.
Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 15784862857c3c2214498defcfed84ff137fb81e
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 17:22:19 2006 +0100
[PATCH] nand_wait() timeout fixes
Two fixes for the nand_wait() function in
drivers/nand/nand_base.c:
1. Use correct timeouts. The original timeouts in Linux
source are 400ms and 20ms not 40s and 20s
2. Return correct error value in case of timeout. 0 is
interpreted as OK.
Signed-off-by: Rui Sousa <rui.sousa@laposte.net>
Signed-off-by: Stefan Roese <sr@denx.de>
commit da5553b095bf04f4f109ad7e565dae3aba47b230
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 17:04:06 2006 +0100
[PATCH] Allow CONFIG_OF_FLAT_TREE to boot a non-arch/powerpc kernel
This patch allows an arch/ppc kernel to be booted by just passing 1 or 2
arguments to bootm. It removes the getenv("disable_of") test that used
to be used for this purpose.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jon Loeliger <jdl@freescale.com>
commit a9398e018593782c5fa7d0741955fc1256b34c1e
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Nov 27 15:32:42 2006 +0100
Minor code cleanup. Update CHANGELOG.
commit 1729b92cde575476684bffe819d0b7791b57bff2
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 14:52:04 2006 +0100
[PATCH] 4xx: Fix problem with board specific reset code (now for real)
Signed-off-by: Stefan Roese <sr@denx.de>
commit cc5ee8a92a0e3ca6f727af71b8fd206460c7afd7
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 14:49:51 2006 +0100
[PATCH] alpr: remove unused board specific flash driver
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1f94d162e2b5f0edc28d9fb11482502c44d218e1
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 14:48:41 2006 +0100
[PATCH] 4xx: Fix problem with board specific reset code
Signed-off-by: Stefan Roese <sr@denx.de>
commit ec0c2ec725aec9524a177a77ce75559e644a931a
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 14:46:06 2006 +0100
[PATCH] Remove testing 4xx enet PHY setup
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1c2ce2262069510f31c7d3fd7efd3d58b8c0c148
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 27 14:12:17 2006 +0100
[PATCH] Update Prodrive ALPR board support (440GX)
Signed-off-by: Stefan Roese <sr@denx.de>
commit 58b485776698c3d71ec5a215e392123b4c15afa3
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon Nov 27 11:51:21 2006 +0100
Add a small README with information on the generic ohci driver.
commit ae3b770e4eae8e98b6e9e29662e18c47fdf0171f
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon Nov 27 11:46:46 2006 +0100
Fix some endianness issues related to the generic ohci driver
commit 7b59b3c7a8ce2e4b567abf99c1cd667bf35b9418
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon Nov 27 11:44:58 2006 +0100
Introduced the configuration option CONFIG_USB_OHCI_NEW in order to be able
to choose between the old and the generic OHCI drivers.
commit 53e336e9ffc51035bdc4e5867631b3378761b4df
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon Nov 27 11:43:09 2006 +0100
Modified the mpc5xxx and the ppc4xx cpu to use the generic OHCI driver
and adapted board configs TQM5200 and yosemite accordingly. This commit
also makes the maximum number of root hub ports configurable
(CFG_USB_OHCI_MAX_ROOT_PORTS).
commit 78d620ebb5871d252270dedfad60c6568993b780
Author: Wolfgang Denk <wd@atlas.denx.de>
Date: Thu Nov 23 22:58:58 2006 +0100
Updates for TQM5200 modules:
- fix off-by-one error in board/tqm5200/cam5200_flash.c error message
- simplify "udate" definitions
commit 2053283304eeddf250d109e6791eb6fa4cad14f7
Author: Stefan Roese <sr@denx.de>
Date: Wed Nov 22 13:20:50 2006 +0100
[PATCH] PPC4xx start.S: Fix for processor errata
Fixed cpu/ppc4xx/start.S for 440EPx Errata: further corrects PPC440EPx
errata 1.12: 440_33 by moving patch up in code.
Signed-off-by: Jeff Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 4ef6251403f637841000e0fef9e832aa01339822
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 20 20:39:52 2006 +0100
[PATCH] Update AMCC Sequoia config file to support 64MByte NOR FLASH
Signed-off-by: Stefan Roese <sr@denx.de>
commit e4bbd8da164b976d38616bd9c69c5e86e193cdf0
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Nov 20 10:28:30 2006 +0100
Update CHANGELOG
commit 260421a21e934a68d31fb6125b0fbd2631a8ca20
Author: Stefan Roese <sr@denx.de>
Date: Mon Nov 13 13:55:24 2006 +0100
[PATCH] CFI driver AMD Command Set Top boot geometry reversal, etc. [Updated]
* Adds support for AMD command set Top Boot flash geometry reversal
* Adds support for reading JEDEC Manufacturer ID and Device ID
* Adds support for displaying command set, manufacturer id and
device ids (flinfo)
* Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
* Removes outdated change history (refer to git log instead)
Signed-off-by: Tolunay Orkun <listmember@orkun.us>
Signed-off-by: Stefan Roese <sr@denx.de>
commit b21b511d4c50408f4853f46f06b601272196223f
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sun Nov 12 21:13:23 2006 +0100
Update CHANGELOG
commit ce3f1a40c507afbab06c5eb58ccdc6713eda3245
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sat Nov 11 22:48:22 2006 +0100
Disable the watchdog in the default config for the V38B board.
commit 44a47e6db2694841211f1c8fdbafd36992e9cd1a
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Sat Nov 11 22:43:00 2006 +0100
Change the GPIO pin multiplexing configuration for V38B. The USB GPIO pin
group is enabled for USB earlier (in cpu_init_f() instead of
usb_lowlevel_init()).
commit 91650b3e4de688038d4f71279c44858e3e2c6870
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Nov 6 17:06:36 2006 +0100
Sequential accesses to non-existent memory must be synchronized,
at least on G2 cores.
This fixes get_ram_size() problems on MPC5200 Rev. B boards.
commit be5e61815d5a1fac290ce9c0ef09cb6a8e4288fa
Author: Timur Tabi <timur@freescale.com>
Date: Fri Nov 3 19:15:00 2006 -0600
mpc83xx: Update 83xx to use fsl_i2c.c
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit d239d74b1c937984bc519083a8e7de373a390f06
Author: Timur Tabi <timur@freescale.com>
Date: Fri Nov 3 12:00:28 2006 -0600
mpc83xx: Replace CFG_IMMRBAR with CFG_IMMR
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit f7fb2e703ec9688541416962724adff70a7322cb
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Thu Nov 2 19:47:11 2006 -0600
mpc83xx: Lindent and clean up cpu/mpc83xx/speed.c
commit 90f30a710a3c619b5405860a686c4ddfc495d4b6
Author: Dave Liu <daveliu@freescale.com>
Date: Thu Nov 2 18:05:50 2006 -0600
mpc83xx: Fix the incorrect dcbz operation
The 834x rev1.x silicon has one CPU5 errata.
The issue is when the data cache locked with
HID0[DLOCK], the dcbz instruction looks like no-op inst.
The right behavior of the data cache is when the data cache
Locked with HID0[DLOCK], the dcbz instruction allocates
new tags in cache.
The 834x rev3.0 and later and 8360 have not this bug inside.
So, when 834x rev3.0/8360 are working with ECC, the dcbz
instruction will corrupt the stack in cache, the processor will
checkstop reset.
However, the 834x rev1.x can work with ECC with these code,
because the sillicon has this cache bug. The dcbz will not
corrupt the stack in cache.
Really, it is the fault code running on fault sillicon.
This patch fix the incorrect dcbz operation. Instead of
CPU FP writing to initialise the ECC.
CHANGELOG:
* Fix the incorrect dcbz operation instead of CPU FP
writing to initialise the ECC memory. Otherwise, it
will corrupt the stack in cache, The processor will checkstop
reset.
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit bf0b542d6773a5a1cbce77691f009b06d9aeb57d
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Nov 1 00:10:40 2006 -0600
mpc83xx: add OF_FLAT_TREE bits to 83xx boards
add ft_pci_setup, OF_CPU, OF_SOC, OF_TBCLK, and
STDOUT_PATH configuration bits to mpc8349emds,
mpc8349itx, and mpc8360emds board code.
redo environment to use bootm with the fdtaddr
for booting ARCH=powerpc kernels by default,
and provide default fdtaddr values.
commit 48041365b3420589ad464ebc7752e0053538b729
Author: Kim Phillips <kim.phillips@freescale.com>
Date: Wed Nov 1 00:07:25 2006 -0600
mpc83xx: change ft code to modify local-mac-address property
Update 83xx OF code to update local-mac-address properties
for ethernet instead of the obsolete 'address' property.
commit 9ca880a250870a7d55754291b5591d2b5fe89b54
Author: Timur Tabi <timur@freescale.com>
Date: Tue Oct 31 21:23:16 2006 -0600
mpc83xx: Fix dual I2C support for the MPC8349ITX, MPC8349EMDS, TQM834x, and MPC8360EMDS
This patch also adds an improved I2C set_speed(), which handles all clock
frequencies.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit ac4b5622ce050b5ee1e154b98df630d778661632
Author: Dave Liu <daveliu@freescale.com>
Date: Tue Oct 31 19:54:59 2006 -0600
mpc83xx: add the README.mpc8360emds
add doc/README.mpc8360emds to accompany the new board support
commit 7737d5c658c606f999dfbe3e86b0fed49e5c50ef
Author: Dave Liu <daveliu@freescale.com>
Date: Fri Nov 3 12:11:15 2006 -0600
mpc83xx: add QE ethernet support
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
commit 5f8204394e39bbe8cd9f08b8f8d145b6c01f7c73
Author: Dave Liu <daveliu@freescale.com>
Date: Fri Nov 3 19:33:44 2006 -0600
mpc83xx: Add MPC8360EMDS basic board support
Add support for the Freescale MPC8360EMDS board.
Includes DDR, DUART, Local Bus, PCI.
commit 23892e49352de74f7fac36ff90bb1be143d195e3
Author: Dave Liu <daveliu@freescale.com>
Date: Tue Oct 31 19:30:40 2006 -0600
mpc83xx: add the QUICC Engine (QE) immap file
common QE immap file. Also required for 8360.
commit b701652a4992bdcc62fb1a6038a85beef9e55da4
Author: Dave Liu <daveliu@freescale.com>
Date: Tue Oct 31 19:25:38 2006 -0600
mpc83xx: Add 8360 specifics to 83xx immap
Mainly add QE device dependencies, with appropriate 8360 protection.
Lindent also run.
commit 988833324a7fda482c8ac3ca23eb539f8232e404
Author: Timur Tabi <timur@freescale.com>
Date: Tue Oct 31 19:14:41 2006 -0600
mpc83xx: Fix PCI, USB, bootargs for MPC8349E-mITX
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006092142000015 "Add support for the MPC8349E-mITX 1/2"
2) DNX#2006092142000024 "Add support for the MPC8349E-mITX 2/2"
CHANGELOG:
* For the 8349E-mITX, fix some size values in pci_init_board(), enable
the clock for the 2nd USB board (Linux kernel will hang otherwise),
and fix the CONFIG_BOOTARGS macro.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 2ad6b513b31070bd0c003792ed1c3e7f5d740357
Author: Timur Tabi <timur@freescale.com>
Date: Tue Oct 31 18:44:42 2006 -0600
mpc83xx: Add support for the MPC8349E-mITX
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 183da6d9b446cc12123455844ad1187e2375626f
Author: Ben Warren <bwarren@qstreams.com>
Date: Tue Sep 12 10:15:53 2006 -0400
Additional MPC8349 support for multibus i2c
Hello,
Here is a patch for a file that was accidentally left out of a previous
attempt.
It accompanies the patch with ticket DNX#2006090742000024
CHANGELOG:
Change PCI initialization to use new multi-bus I2C API.
regards,
Ben
commit b24f119d672b709d153ff2ac091d4aa63ec6877d
Author: Ben Warren <bwarren@qstreams.com>
Date: Thu Sep 7 16:51:04 2006 -0400
Multi-bus I2C implementation of MPC834x
Hello,
Attached is a patch implementing multiple I2C buses on the MPC834x CPU
family and the MPC8349EMDS board in particular.
This patch requires Patch 1 (Add support for multiple I2C buses).
Testing was performed on a 533MHz board.
/*** Note: This patch replaces ticket DNX#2006083042000027 ***/
Signed-off-by: Ben Warren <bwarren@qstreams.com>
CHANGELOG:
Implemented driver-level code to support two I2C buses on the
MPC834x CPU family and the MPC8349EMDS board. Available I2C bus speeds
are 50kHz, 100kHz and 400kHz on each bus.
regards,
Ben
commit bb99ad6d8257bf828f150d40f507b30d80a4a7ae
Author: Ben Warren <bwarren@qstreams.com>
Date: Thu Sep 7 16:50:54 2006 -0400
Add support for multiple I2C buses
Hello,
Attached is a patch providing support for multiple I2C buses at the
command level. The second part of the patch includes an implementation
for the MPC834x CPU and MPC8349EMDS board.
/*** Note: This patch replaces ticket DNX#2006083042000018 ***/
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Overview:
1. Include new 'i2c' command (based on USB implementation) using
CONFIG_I2C_CMD_TREE.
2. Allow multiple buses by defining CONFIG_I2C_MULTI_BUS. Note that
the commands to change bus number and speed are only available under the
new 'i2c' command mentioned in the first bullet.
3. The option CFG_I2C_NOPROBES has been expanded to work in multi-bus
systems. When CONFIG_I2C_MULTI_BUS is used, this option takes the form
of an array of bus-device pairs. Otherwise, it is an array of uchar.
CHANGELOG:
Added new 'i2c' master command for all I2C interaction. This is
conditionally compiled with CONFIG_I2C_CMD_TREE. New commands added for
setting I2C bus speed as well as changing the active bus if the board
has more than one (conditionally compiled with
CONFIG_I2C_MULTI_BUS). Updated NOPROBE logic to handle multiple buses.
Updated README.
regards,
Ben
commit bed85caf872714ebf53013967a695c9d63acfc68
Author: Timur Tabi <timur@freescale.com>
Date: Tue Oct 31 18:13:36 2006 -0600
mpc83xx: Add support for Errata DDR6 on MPC 834x systems
CHANGELOG:
* Errata DDR6, which affects all current MPC 834x processors, lists changes
required to maintain compatibility with various types of DDR memory. This
patch implements those changes.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit afd6e470f639883002c7c59d562690a5cb0f4865
Author: Timur Tabi <timur@freescale.com>
Date: Wed Oct 25 18:45:23 2006 -0500
mpc83xx: fix TQM build by defining a CFG_FLASH_SIZE for it
commit 31068b7c4abeefcb2c8fd4fbeccc8ec6c6d0475a
Author: Timur Tabi <timur@freescale.com>
Date: Tue Aug 22 17:07:00 2006 -0500
mpc83xx: Add support for variable flash memory sizes on 83xx systems
CHANGELOG:
* On 83xx systems, use the CFG_FLASH_SIZE macro to program the LBC local access
window registers, instead of using a hard-coded value of 8MB.
Signed-off-by: Timur Tabi <timur@freescale.com>
commit 2fc34ae66e73fa7841d1a006dc1b5dcbc1f78965
Author: Tanya Jiang <tanya.jiang@freescale.com>
Date: Thu Aug 3 18:38:13 2006 +0800
mpc83xx: Unified TQM834x variable names with 83xx and consolidated macros
Unified TQM834x variable names with 83xx and consolidated macro
in preparation for the 8360 and other upcoming 83xx devices.
Signed-off-by: Tanya Jiang <tanya.jiang@freescale.com>
commit f6eda7f80ccc13d658020268c507d7173cf2e8aa
Author: Dave Liu <daveliu@freescale.com>
Date: Wed Oct 25 14:41:21 2006 -0500
mpc83xx: Changed to unified mpx83xx names and added common 83xx changes
Incorporated the common unified variable names and the changes in preparation
for releasing mpc8360 patches.
Signed-off-by: Dave Liu <daveliu@freescale.com>
commit 3894c46c27c64891f93ac04edde86a9fa9758d92
Author: Tanya Jiang <tanya.jiang@freescale.com>
Date: Thu Aug 3 18:36:02 2006 +0800
mpc83xx: Fix missing build for mpc8349emds pci.c
Make pci build for mpc8349emds
Signed-off-by: Tanya Jiang <tanya.jiang@freescale.com>
commit 09a81ff740b29deea1e2ab08a3c2ac136c2e6219
Author: Tanya Jiang <tanya.jiang@freescale.com>
Date: Thu Aug 3 18:39:49 2006 +0800
mpc83xx: Removed unused file resetvec.S for mpc83xx cpu
Removed unused file resetvec.S for mpc83xx cpu
Signed-off-by: Tanya Jiang <tanya.jiang@freescale.com>
commit 04f899fc465c3e44f2b55ecc70618f5696fc0ddf
Author: Nick Spence <Nick.Spence@freescale.com>
Date: Sat Sep 30 00:32:59 2006 -0700
NAND Flash verify across block boundaries
This patch addresses a problem when CONFIG_MTD_NAND_VERIFY_WRITE is
defined
and the write crosses a block boundary. The pointer to the verification
buffer (bufstart) is not being updated to reflect the starting of the
new
block so the verification of the second block fails.
CHANGELOG:
* Fix NAND FLASH page verification across block boundaries
commit f484dc791a3932537213c43c654cc1295c64b84c
Author: Nick Spence <nick.spence@freescale.com>
Date: Thu Sep 7 07:39:46 2006 -0700
Added RGMII support to the TSECs and Marvell 881111 Phy
Added a phy initialization to adjust the RGMII RX and TX timing
Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode
Signed-off-by: Nick Spence <nick.spence@freescale.com>
commit 4831c8b8a97799da77923d6bbb4c260c0d45521c
Author: roy zang <tie-fei.zang@freescale.com>
Date: Fri Nov 3 13:10:00 2006 +0800
Remove some unused CFG define.
undef CFG_DRAM_TEST
commit 99c09c4dec34f77c243bf51bea532e3f339410ad
Author: roy zang <tie-fei.zang@freescale.com>
Date: Fri Nov 3 13:07:36 2006 +0800
Change the TEXT_BASE from 0xFFF00000 to 0xFF000000.
Both work. 0xFF000000 seems more reasonable.
commit c59200443072353044aa4bf737a5a60f9a9af231
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Nov 2 15:15:01 2006 +0100
Release U-Boot 1.1.6
commit c1fbe4103a0d6c8957f912af902d705ba67836f2
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 19:14:48 2006 +0800
This patch comes from Yuli's posted patch on 8/8/2006
titled "CFI Driver Little-Endian write Issue".
http://sourceforge.net/mailarchive/message.php?msg_id=36311999
If that patch applied, please discard this one.
Until now , I do not see his patch is applied. So please apply this one.
Signed-off-by: Yuli Barcohen <yuli@arabellasw.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit b825f158e449e1e9cf74c08e572955e122394c96
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 19:12:31 2006 +0800
Tsi108 on chip i2c support.
The i2c Interface provides a master-only, serial interface that can be
used for initializing Tsi108/Tsi109 registers from an EEPROM after a
device reset.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 9226e7d6f09b9a1ac074cd918c81225a4689bba8
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 19:11:06 2006 +0800
Tsi108 on chip pci controller support.
If there is no pci card, the tsi108/109 pci configure read will
cause a machine check exception to the processor. PCI error should
also be cleared after the read.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit d1927cee977126e547ceeba23e4f978f377cfb8f
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 19:08:55 2006 +0800
Tundra tsi108 on chip Ethernet controller support.
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface
to manage the two physical connection devices (PHYs). Each Ethernet port
has its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric
through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels
use descriptors set up in memory, the memory map of the device, and
access via the Switch Fabric. The Ethernet Controller?s DMA arbiter
handles arbitration for the Switch Fabric. The Controller also
has a register businterface for register accesses and status monitor
control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each Ethernet port uses its transmit and receive DMA channels to manage
data flows through buffer descriptors that are predefined by the
system (the descriptors can exist anywhere in the system memory map).
These descriptors are data structures that point to buffers filled
with data ready to transmit over Ethernet, or they point to empty
buffers ready to receive data from Ethernet.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 78aa0c3427f3ecdeb34aabfbbe2dd23b6ad8f40e
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 19:01:33 2006 +0800
Tundra tsi108 header file.
The Tundra Semiconductor Corporation (Tundra) Tsi108 is a host bridge for
PowerPC processors that offers numerous system interconnect options for
embedded application designers. The Tsi108 can interconnect 60x or
MPX processors to PCI/X peripherals, DDR2-400 memory, Gigabit Ethernet,
and Flash. Provided the macro define for tsi108 chip.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 87c4db09699c6b89176b31004afcb83eb1585d47
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:59:15 2006 +0800
Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
mpc7448hpc2 board support high level code:tsi108 init + mpc7448hpc2.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 27801b8ab11c61b577e45742a515bb3b23b80241
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:57:21 2006 +0800
Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
Make ,config.mk and link file for the mpc7448hpc2 board.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit c6411c0c3bbc79f9ba8aef58296a42d8f9d8a0a6
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:55:04 2006 +0800
Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
The mpc7448hpc2 board support header file.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 625bb5ddb50b243f931262ca8c46956409471917
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:52:21 2006 +0800
Add mpc7448hpc2 (mpc7448 + tsi108) board associated code support.
The mpc7448hpc2 board support low level assemble language init code.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 4c52783b3d024e153c4972b97332e314bc3bdc46
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:49:51 2006 +0800
General code modification for mpc7448hpc2 board support.
1. Add 7447A and 7448 processor support.
2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
(such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan
the slots, if there is no pci card, the tsi108/9 will cause a machine
check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 69366bf42f22d67efce8da3f8c40a43d4a3c2695
Author: roy zang <tie-fei.zang@freescale.com>
Date: Thu Nov 2 18:34:47 2006 +0800
Add README file for mpc7448hpc2 board.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
commit 25721b5cec2be4bce79cfade17ec8f6aa1e67526
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Nov 1 02:04:38 2006 +0100
Finish up support for MarelV38B board
- add watchdog support
- enable GPIO_WKUP_7 pin for input
- code cleanup
commit ffa150bc90c943ca265170bd1be3f293674dd5c7
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Nov 1 01:45:46 2006 +0100
- Fix issues related to the use of ELDK 4 when compiling for MarelV38B:
* remove warnings when compiling ethaddr.c
* adjust linker script (fixes a crash resulting from incorrect
definition of __u_boot_cmd_start)
- Some MarelV38B code cleanup.
commit dae80f3caf9754a6dd3ddf3cf903d0c46cbd4385
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Nov 1 01:38:16 2006 +0100
- Add MPC5XXX register definition MPC5XXX_WU_GPIO_DATA_I and change the
MPC5XXX_WU_GPIO_DATA macro to MPC5XXX_WU_GPIO_DATA_O (per MPC5200 User's
Manual). Replace the uses of MPC5XXX_WU_GPIO_DATA with
MPC5XXX_WU_GPIO_DATA_O for affected boards.
- Add defintions for some MPC5XXX GPIO pins.
commit 82d9c9ec29a1bec1b03ba616425ebaed231072c8
Author: Bartlomiej Sieka <tur@semihalf.com>
Date: Wed Nov 1 01:34:29 2006 +0100
Changed MarelV38B board make target to lowercase. Config file cleanup.
commit 1954be6e9c9421b45d0a9d05b10356acc7563150
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sun Oct 29 01:03:51 2006 +0200
Automatically adjust ARFLAGS so "make -s" is really silent.
commit fae684e89844856383bdf101440889557df3e6b1
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 28 16:45:00 2006 +0200
[PATCH] omap925.c: Remove unused functions
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 1265581502ab8ea8c08e8edbe9bf64fbd62fd776
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 28 17:12:58 2006 +0200
[PATCH] Add some missing machtypes for netstar & voiceblue boards
Use MACH_TYPE_NETSTAR and MACH_TYPE_VOICEBLUE defines instead of
numbers in code.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 856f054410cef52d868feb330168b2a4c4091328
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 28 15:55:52 2006 +0200
[PATCH] NAND: Partition name support added to NAND subsystem
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
commit 07a69a18c2ecfda904231fdf23e2523ea7792eb6
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sat Oct 28 02:29:44 2006 +0200
Update CHANGELOG.
commit 2751a95abd1b96911081c357e96a12fa97b40dee
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sat Oct 28 02:29:14 2006 +0200
Enable commandline editing and hush shell on all TQM boards.
commit 8078f1a5f63a739b8533478f6c2b62fb1e2f79d7
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sat Oct 28 02:28:02 2006 +0200
README says CFG_AUTO_COMPLETE, but ocde uses CONFIG_AUTO_COMPLETE
commit 471a7be7a042e95e440f5de969c9765214ae8d6e
Author: Wolfgang Denk <wd@denx.de>
Date: Sat Oct 28 01:14:32 2006 +0200
Check for illegal character '=' in environment variable names.
Make sure the string passed as variable name does not contain a '='
character. This not only prevents the common error or typing
"setenv foo=bar" instead of "setenv foo bar", but (more importantly)
also closes a backdoor which allowed to delete write-protected
environment variables, for example by using "setenv ethaddr=".
commit 19973b6ad9863a56f5c5fbcfd90e20ab2490a2c2
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Sat Oct 28 00:38:39 2006 +0200
Minor code cleanup.
commit e11887a77d81077416a2d1c5e0354916fee8c034
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Thu Oct 26 17:55:31 2006 +0200
Don't pass any debug options directly to the assembler
When passing the -g option to gcc, gcc automatically selects a
suitable --g<format> option to pass on to the assembler.
Thus, there's no point in forcing a specific debug option on the
assembler using the -Wa mechanism.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit ea08ff6e14f9ebb8c07cfa79c51ef540eb087393
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Oct 27 07:47:22 2006 -0500
MPC86xx: Cleaned up unused and conditionally used local variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d38936cdae46bfd2623ff83f6ce9b616d36ab0f9
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Fri Oct 27 11:55:21 2006 +0200
Fix "ar" flags in some Makefiles to allow for silent "make -s"
commit 4653f91c13ed51c21cc4c3855745d69a3fb1817f
Author: Ben Warren <bwarren@qstreams.com>
Date: Thu Oct 26 14:38:25 2006 -0400
Fix TSEC driver (now for real): avoid crashes if PHY is not attached
to a TSEC (e.g. a switch is connected via RMII) or
if the PHY is defective/incorrectly configured.
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit b985b5d6e4fb88f508f7aa0f126c2e27ada2b999
Author: Ben Warren <bwarren@qstreams.com>
Date: Thu Oct 26 14:38:25 2006 -0400
Fix TSEC driver: avoid crashes if PHY is not attached
to a TSEC (e.g. a switch is connected via RMII) or
if the PHY is defective/incorrectly configured.
Signed-off-by: Ben Warren <bwarren@qstreams.com>
commit 2b2a40bebbf1822506e80e631d7253e60f0e0fe6
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Thu Oct 26 16:24:31 2006 +0200
Code cleanup.
commit 5e3b0bc19f07ed277d85324ad0427642c8981baf
Author: Haavard Skinnemoen <hskinnemoen@atmel.com>
Date: Wed Oct 25 15:48:59 2006 +0200
Finish up support for the ATSTK1000/ATSTK1002 boards
Add atstk1002_config target to Makefile and move the AVR32 section
down below Blackfin so that it doesn't end up in the middle of
MIPS.
Drop the autogenerated linker script thing for now. Will have to
revisit how to handle chips with different flash and RAM layout
later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit c76f951a747cfb87ba826ef45b5aea82d5b5dbb4
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue Oct 24 23:47:37 2006 -0500
Added support for Multi-Image files that contain a device tree
If a Multi-Image file contains a third image we try to use it as a
device tree. The device tree image is assumed to be uncompressed in the
image file. We automatically allocate space for the device tree in memory
and provide an 8k pad to allow more than a reasonable amount of growth.
Additionally, a device tree that was contained in flash will now automatically
get copied to system memory as part of boot. Previously an error was
reported if one tried to boot a device tree that was in flash.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 7c52c4b943ff52bbe8796a7e2d3e476ceaf3f512
Author: Wolfgang Denk <wd@denx.de>
Date: Tue Oct 24 21:35:55 2006 +0200
Switch to automatically generated CHANGELOG file.
(use "make CHANGELOG" to update it from time to time)
commit 7ade0c634a979c32fa91a74e8f5775f24651fbe6
Author: Stefan Roese <sr@denx.de>
Date: Tue Oct 24 18:06:48 2006 +0200
Fix bug in PPC440 NAND driver cpu/ppc4xx/ndfc.c
Patch by Stefan Roese, 24 Oct 2006
commit 8ae3b713b2286e0c3213b7802062e4c1599010de
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 17:24:55 2006 +0200
Merge with /home/wd/git/u-boot/master
commit 47a6989c10685d2ab3efcf95228ce50d2a496d3e
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 15:32:57 2006 +0200
Code cleanup
commit 3a78e3e75b633ecb6413114ffd11e2f000c4f11e
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 14:51:36 2006 +0200
Move atstk1000 files into vendor specific directory.
Patch by Haavard Skinnemoen, 12 Sep 2006
commit 6ccec4492e77428fd6eafd3dfe94fbdf08e91d37
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 14:42:37 2006 +0200
Add ATSTK1000 and ATSTK1002 board support
Patch by Haavard Skinnemoen, 06 Sep 2006
This patch adds support for the ATSTK1000 with the ATSTK1002 CPU
daughterboard.
ATSTK1000 is a full-featured development board for AT32AP CPUs. It
has two ethernet ports, a high quality QVGA LCD panel, a loudspeaker,
and connectors for USART, PS/2, VGA, USB, MMC/SD cards and
CompactFlash cards. For more information, please see this page:
http://www.atmel.com/dyn/products/tools.asp?family_id=682
The ATSTK1002 is a daughterboard for the ATSTK1000 supporting the
AT32AP7000 chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit f93ae788c3640fcde5db383471d45548ff4060d0
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 14:31:24 2006 +0200
Add common serial driver for Atmel AT32 and AT91 chips
Patch by Haavard Skinnemoen, 06 Sep 2006
This is a first attempt at creating a common serial driver for Atmel
chips. For now, it supports the AT32AP7000 AVR32 chip, but it should
be possible to support AT91RM9200 and other ARM-based chips with some
minor modifications.
There's nothing fundamentally AVR32-specific in this driver, but it
does use some features which are currently only defined for the
AT32AP CPU port:
* pm_get_clock_freq: Obtain the clock frequency of a given domain
* gd->console_uart: A "struct device" containing information about
register mappings, gpio resources and clocks associated with the
UART device.
For more information about these features, please see the "AT32AP
CPU" patch.
commit 72a087e04705c26cad982879ebd06b5281bf825a
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 14:27:35 2006 +0200
Add AT32AP CPU and AT32AP7000 SoC support
Patch by Haavard Skinnemoen, 06 Sep 2006
This patch adds support for the AT32AP CPU family and the AT32AP7000
chip, which is the first chip implementing the AVR32 architecture.
The AT32AP CPU core is a high-performance implementation featuring a
7-stage pipeline, separate instruction- and data caches, and a MMU.
For more information, please see the "AVR32 AP Technical Reference":
http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf
In addition to this, the AT32AP7000 chip comes with a large set of
integrated peripherals, many of which are shared with the AT91 series
of ARM-based microcontrollers from Atmel. Full data sheet is
available here:
http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 7b64fef33c66be648826c0ff9758298ef13d0604
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 14:21:16 2006 +0200
Add AVR32 architecture support
Patch by Haavard Skinnemoen, 6 Sep 2006 16:23:02 +0200
This patch adds common infrastructure code for the Atmel AVR32
architecture. See doc/README.AVR32 for details.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
commit 2da2d9a4766063b9848f3a35ad6025499cf87265
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 13:57:33 2006 +0200
Use -g instead of -gstabs in AFLAGS_DEBUG
Patch by Haavard Skinnemoen, 30 Aug 2006
In config.mk, -Wa,-gstabs is unconditionally appended to AFLAGS no
matter what the target's preferred debugging format is. This patch
simply replaces -gstabs with -g, so that the default debugging format
for the architecture is used.
commit 965829872169c2996023840d98e1d85ad148d629
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Tue Oct 24 13:55:18 2006 +0200
Fix/workaround broken dependency handling with make 3.81
Based on patch by Haavard Skinnemoen, 29 Aug 2006 11:20:39 +0200
commit 8318fbf8cc30418b621ea9f39b84b4c1a08f003a
Author: Marian Balakowicz <m8@semihalf.com>
Date: Mon Oct 23 22:17:05 2006 +0200
Fix sequoia separate object direcory building problems.
commit 3dfa9cfdcee78b30da3432318b32821ffabe974b
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Oct 20 17:16:35 2006 -0500
Use generic I2C register block on 85xx and 86xx.
Replace private IMMAP I2C structures with generic reg block
and allow 86xx to have multiple I2C device busses.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit f5012827df11ca0c9be1df5f8b153e188dc2fa7c
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Oct 20 15:54:34 2006 -0500
Fix compilation warnings on a few 85xx boards.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 2047672684cf85cb6f96a1fbc993180aaaf19a99
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Oct 20 15:50:15 2006 -0500
Converted all 85xx boards to use a common FSL I2C driver.
Introduced COFIG_FSL_I2C to select the common FSL I2C driver.
And removed hard i2c path from a few u-boot.lds scipts too.
Minor whitespace cleanups along the way.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4d45f69e362b05892c9e92a7907e5820995612aa
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Oct 19 12:02:24 2006 -0500
Rewrite a series of goto statements as a sequences of
conditional expressions instead.
Use consistent return code 0/-1 for good/bad indicators.
Include one fewer file if the driver isn't used at all.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 7237c033b02fe295880435f1eb80819a0c987532
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Oct 19 11:02:16 2006 -0500
Moved i2c driver out of cpu/mpc86xx/i2c.c into drivers/fsl_i2c.c
in an effort to begin to unify the umpteen FSL I2C drivers that
are all otherwise very similar.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 13a7fcdf37f6ea9429ae04c9df67f893364cfe4b
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Oct 19 11:33:52 2006 -0500
* Fix a bunch of compiler warnings for gcc 4.0
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit af9e1f5b9e6f9ce810f5e8bf2961c9542a5865c2
Author: Stefan Roese <sr@denx.de>
Date: Tue Oct 17 06:14:31 2006 +0200
Add monitor functions for indirect access to PPC440 DCR's
Patch by Leonid Baryudin, 12 Oct 2006
commit 5f3249a0a168e446a4cc9669b2bce0bc456f0a09
Author: Jon Loeliger <jdl@freescale.com>
Date: Fri Oct 13 16:47:53 2006 -0500
Fixed leading whitespace issues.
Removed spurious LAWAR thing.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 0ee90cb77e01d6e8ccd37e1bd96678597875c391
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Oct 12 10:42:36 2006 -0500
Remove unneeded include files and local variable.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 1eaf3a5ff4960a46f3a9063568ba2af7883f07c5
Author: Grant Likely <grant.likely@secretlab.ca>
Date: Tue Oct 10 00:23:32 2006 -0600
Fix possible uninitialized variable compiler warning.
When CONFIG_OF_FLAG_TREE is set, the compiler complains that 'len' in
do_bootm_linux() may be uninitialized. There is no possibility in the
current code that len will get used uninitialized, but this fix follows
the existing convention of setting both len and data to zero at the same
time.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 7376eb87aaa601f728f9b8e5e9cd2711a67f529e
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Oct 11 15:13:01 2006 -0500
* Fix a bunch of compiler warnings for gcc 4.0
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit bf651baa365e5447246aad6a633ccd667cf24a39
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Oct 11 10:10:43 2006 -0500
Move "ar" flags to config.mk to allow for silent "make -s"
commit 1fd5699a4a24f5c1dab1b32f480bace1ebb9fc3e
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:19:03 2006 -0500
Coding style changes to remove local varible blocks
and reformat a bit nicer.
commit 8b283dbb3a08d1b8d406bc15f119e081b3e2606a
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:16:04 2006 -0500
Fix whitespace issues.
commit 7b382b7125f2397cce63253df62f183e3dfa2770
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:14:45 2006 -0500
Fix whitespace issues.
commit e10390ddd736b0dad1528eec4b0fe35c0827139a
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:06:53 2006 -0500
Fix whitespace issues.
commit 89875e96ba3f023157bf50d5f8e33bf254964a76
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:03:43 2006 -0500
Ran lindent and cleaned up whitespace issues.
Format for 80-columns too.
commit 333961ae7095fc66d8a041fce1ac9ee873b09d86
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Oct 10 17:02:22 2006 -0500
Fix whitespace and 80-col issues.
commit 5c912cb1c31266c66ca59b36f9b6f87296421d75
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 7 11:36:51 2006 +0200
CFG_NAND_QUIET_TEST added to not warn upon missing NAND device
Patch by Stefan Roese, 07 Oct 2006
commit 5bc528fa4da751d472397b308137238a6465afd2
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 7 11:35:25 2006 +0200
Update ALPR code (NAND support working now)
Patch by Stefan Roese, 07 Oct 2006
commit 77d5034847d328753b80c46b83f960a14a26f40e
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 7 11:33:03 2006 +0200
Remove compile warnings in fpga code
Patch by Stefan Roese, 07 Oct 2006
commit f3443867e90d2979a7dd1c65b0d537777e1f9850
Author: Stefan Roese <sr@denx.de>
Date: Sat Oct 7 11:30:52 2006 +0200
Add CONFIG_BOARD_RESET to configure board specific reset function
Patch by Stefan Roese, 07 Oct 2006
commit f55df18187e7a45cb73fec4370d12135e6691ae1
Author: John Traill <john.traill@freescale.com>
Date: Fri Sep 29 08:23:12 2006 +0100
Fix missing tCycle/modfreq calculation.
Signed-off-by: John Traill <john.traill@freescale.com>
commit 8272dc2f58f2473d8995fcc9b916440cfba080f0
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Sep 13 10:33:35 2006 -0500
Updated config headers to add default FDT-based booting
commit 09f3e09e9ebcfa7919ca8931a4b5504fadd1f1d3
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Sep 13 10:34:18 2006 -0500
Add support for eTSEC 3 & 4 on 8548 CDS
* Added support for using eTSEC 3 and eTSEC 4 on the 8548 CDS.
This will only work on rev 1.3 boards (but doesn't break older boards)
* Cleaned up some comments to reflect the expanded role of tsec
in other systems
commit 084d648b109c8984f83674043c1a7fa3885ef801
Author: Andy Fleming <afleming@freescale.com>
Date: Wed Sep 13 10:33:56 2006 -0500
Added code to support 2.6.18 PCI changes in u-boot
* Added code to swizzle the IRQ map for the PCI
commit afbdc649f8751e4f4f1a6f527edfe139773f2c15
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Sep 19 09:34:10 2006 -0500
Modified makefile for new build mechanism.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit d14ba6a798beb753e7a864500414fcc2d198b8bc
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Sep 14 08:40:36 2006 -0500
Handle 86xx SVR values according to the new Reference Manual.
Both 8641 and 8641D have SVR == 0x8090, and are distinguished
by the byte in bits 16-23 instead.
Thanks to Jason Jin for noticing.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 88c8f4921fc47fb0eb2384b16586f1bd7f275be7
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Mon Aug 28 14:25:31 2006 +0800
Fixed an OF-tree off-by-one bug when adding a new property name.
This bug will cause the kernel booting to pause a long time.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
(cherry picked from 2f15776ccc6dc32377d8ba9652b8f58059c27c6d commit)
commit 9bff7a69a885adebbd2bd45990494ec4cf998a30
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 29 11:05:09 2006 -0500
Remove trailing empty lines.
commit cd6d73d5b895a5935ac4fde0a356288142a584e0
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 29 09:48:49 2006 -0500
Remove bogus msync and use volatile asm.
commit 778d45049ce5927b65b3ff1d8e6692b654bdd49e
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 29 08:17:14 2006 -0500
Add myself as maintainer for MPC8641HPCN.
commit 2f15776ccc6dc32377d8ba9652b8f58059c27c6d
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Mon Aug 28 14:25:31 2006 +0800
Fixed an OF-tree off-by-one bug when adding a new property name.
This bug will cause the kernel booting to pause a long time.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit 5567806b67d0ae83493aa8823ad3b6c914f581d7
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Fri Aug 25 14:38:34 2006 -0400
Change ramdiskaddr and dtbaddr
Remove PEX fluff commands.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b2b78421d9db49c21a821af8a19c21c1f7dfb29e
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Aug 23 13:32:45 2006 -0500
* Another small fix for booting with disable_of
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit 4a7cc0f21918e6ecf07ed57075d67df2c4a1299c
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Aug 23 11:04:43 2006 -0500
Cleanup and lindent new AHCI driver.
commit dabf9ef8c10b4dead5ef2106ef742b1c06b542de
Author: Jin Zhengxiong <jason@bus.ap.freescale.net>
Date: Wed Aug 23 19:15:12 2006 +0800
Add AHCI define and sata support for MPC8641HPCN board.
Signed-off-by:Jason Jin<jason.jin@freescale.com>
commit 4782ac80b02f0d01afd309e2200dd3c7037f2ba4
Author: Jin Zhengxiong <jason@bus.ap.freescale.net>
Date: Wed Aug 23 19:10:44 2006 +0800
Add AHCI support to u-boot
Add AHCI support in u-boot, enable the sata disk controllers which
following the AHCI protocol.
Signed-off-by:Jason Jin<jason.jin@freescale.com>
commit d8ea2acf5f137cae99417df4f573d036ee384668
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Wed Aug 23 17:54:32 2006 +0800
Add dtb boot-up parameter to default boot commands.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit b93775c2036b99baa390ea425c4771895bbc63c4
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 18:26:08 2006 -0500
Cleanup even more poorly introduced whitespace.
commit ae6241685cbcf0c79a3636530d2ceab1fb291a94
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 18:07:00 2006 -0500
Cleanup more poorly introduced whitespace.
commit 2c33e8a1c535b3ae91cf0b284480600bf3f57c57
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 17:54:05 2006 -0500
Cleanup poorly introduced whitespace.
commit 80e955c7dd98f4b4fd23c2113caf75ed2b77b5b3
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 12:25:27 2006 -0500
General indent and whitespace cleanups.
commit ffff3ae56f5842ca3679e4ce7922b819a87aad9f
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 12:06:18 2006 -0500
General indent and whitespace cleanups.
commit 41a0e8b304d3ff55fe27a230507aac79684016ac
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue Aug 22 10:42:21 2006 -0500
Cleanup compiler warnings.
commit 5de62c47a8628b3da4d73f7c07027f32a3342d40
Author: Matthew McClintock <msm@freescale.com>
Date: Tue Aug 22 09:31:59 2006 -0500
Fix disable_of booting
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit 87a449c8ac396420cb24260f717ea9e6faa82047
Author: Matthew McClintock <msm@freescale.com>
Date: Tue Aug 22 09:23:55 2006 -0500
Support for FDT in uImage format, error when using FDT from flash
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit 75c299c38369d01addd5e054b8a16217b70f4a86
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Tue Aug 15 15:12:55 2006 -0400
Unlock cache before kernel starts up for MPC86xx
commit 67256678f00c09b0a7f19e862e5c1847553d31bc
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Tue Aug 15 15:13:15 2006 -0400
Copy Global Data Pointer to r29 for DECLARE_GLOBAL_DATA_PTR
commit 1c8f6d8fb028f156094d05f2d14298e6479364ac
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Tue Aug 15 15:12:55 2006 -0400
Unlock cache before kernel starts up for MPC86xx
commit 0d9ccc55edf9a7f3c5b2b6263580a6ea8d702a04
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Tue Aug 15 15:13:15 2006 -0400
Copy Global Data Pointer to r29 for DECLARE_GLOBAL_DATA_PTR
commit 86c8e17f25e972a7e272950a0735fad84e082b88
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Aug 16 13:59:47 2006 -0500
* Fix disable_of booting
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit 25c751e9adc86e22fe3b5b47cf2806379b575db7
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Aug 16 10:54:09 2006 -0500
* Support for FDT in uImage format, error when using FDT from flash
Signed-off-by: Matthew McClintock <msm@freescale.com>
commit 899620c2d66d4eef3b2a0034d062e71d45d886c9
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 15 14:22:35 2006 +0200
Add initial support for the ALPR board from Prodrive
NAND needs some additional testing
Patch by Heiko Schocher, 15 Aug 2006
commit f0ff4692ff3372dec55074a8eb444943ab095abb
Author: Stefan Roese <sr@denx.de>
Date: Tue Aug 15 14:15:51 2006 +0200
Add FPGA Altera Cyclone 2 support
Patch by Heiko Schocher, 15 Aug 2006
commit fecf1c7e4de1b2779edc18742b91c22bdc32b68b
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon Aug 14 15:33:38 2006 -0500
Fix BAT0 to actually be cacheable, non-guarded as documented.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 40bc83559db5745681909fd7382ae509567e116d
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Aug 9 15:32:16 2006 -0500
Removed MPC8641HPCN DTS source file from build.
It is no longer linked into U-Boot; its sources are
now located in the kernel tree.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 34c3c0e01dbf1f8cc2bd08de92f2b89ba84921eb
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:47:03 2006 -0500
* Switched default PCI speed for 8540 ADS back to 33MHz
* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit b6c5e1373b6ea0bb37a18e4aeecec00613d1cd39
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:46:35 2006 -0500
* Fixed a bug where 8555 PCI code used the old variable and function names Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit bf1dfffd8c26f8ecdd630a0ae4c834e751e4e452
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:46:13 2006 -0500
* Added VIA configuration table
* Added support for PCI2 on CDS
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit c88f9fe66b64247e5b6a38410ba315ca25596d16
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:45:41 2006 -0500
* Fixed PCI memory definitions Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 97074ed9655309b64231bc2cee69fe85399f8055
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:45:17 2006 -0500
* Added support for initializing second PCI bus on 85xx Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit f0e6f57f71b3c4fdd13028eb03c3f3e91926dda2
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:44:49 2006 -0500
* Added PCI-X #defines for PCI-X initialization Patch by Andy Fleming on 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit a4e11558b810ef2cddffdf7b9d86bc1130441960
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:44:23 2006 -0500
* Made sure the code which disables prefetch for PCI devices sets the size of the prefetch region to 0 Patch by Andy Fleming on 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 0e16387db1d4aacd5bf35cb6d7c1942765c0347b
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:43:36 2006 -0500
* Add Flat Dev Tree construction for MPC85xx ADS and CDS boards Patch by Jon Loeliger 17-Jan-2006
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 855e6fb073f9d04fe4a7f06c107ecbac6344ddd4
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:43:00 2006 -0500
* Removed the oftree.dts for stxxtx in light of the changes to the flat device tree handling code Patch by Matthew McClintock 26-June-2006
commit 5498d90312aad9f6bdbf047986027c35b03cd163
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:42:24 2006 -0500
* Patch to modify ft_build.c to update flat device trees in place Patch by Matthew McClintock 26-June-2006
commit 0267768eddc5ca7bc1865bc40c866829ac5efbfe
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:41:37 2006 -0500
* Modify bootm command to support booting with flat device trees Patch by Matthew McClintock 26-June-2006
commit 8fc8bd2cc479b6cd188fdede4010e0e052970b8a
Author: John Traill <john.traill@freescale.com>
Date: Wed Aug 9 14:33:50 2006 +0100
Add Rapidio support for the MPC8641HPCN
Signed-off-by: John Traill <john.traill@freescale.com>
commit 91a414c7d1fb0eac912592cd995b30c9f23045c9
Author: John Traill <john.traill@freescale.com>
Date: Tue Aug 8 11:32:43 2006 +0100
Fix caslat calculation
Signed-off-by: John Traill <john.traill@freescale.com>
commit 709d3073e74153278e7904a70819bbef7df50e1a
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Aug 3 16:17:56 2006 -0500
Convert to mac-address in ethernet nodes.
commit 71748af833ca1017edf1415be376366ff2937d17
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Fri Jul 28 12:41:35 2006 -0400
Correct the irq value of DUART2
commit 9cb3e8816ae4d854e7dc22128c3eea3d70bb982c
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Fri Jul 28 12:41:41 2006 -0400
Change the space size of PEX IO in README
commit 239db37c94f7a92941c4465feceb867c609241c5
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Fri Jul 28 12:41:18 2006 -0400
Move get_board_sys_clk to board directory
commit 492900b985439fbce1a118afde1e35def870db03
Author: John Traill <john.traill@freescale.com>
Date: Fri Jul 28 09:03:54 2006 +0100
Fix 8641HPCN pollution
commit 515ab8a62e8574e2babc6e8dcc43544ad221c5b2
Author: John Traill <john.traill@freescale.com>
Date: Fri Jul 28 08:16:06 2006 +0100
Fix 8641HPCN timebase
commit c86360b830f1eecd7a72208575dde4f57879faea
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Fri Jul 28 00:01:34 2006 +0800
Fixed OF device tree of mpc86xxhpcn board.
The changes works in with kernel irq mapping rework.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
commit bea3f28d285942bf3f7ab339ce85178ded544225
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Wed Jul 12 10:48:05 2006 -0400
Add support for reading and writing mac addresses to or from ID EEPROM.
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
commit fcb28e763415e0e4e66b0f45842d1557ae198e5e
Author: Jin Zhengxiong <Jason.Jin@freescale.com>
Date: Thu Jul 13 10:35:10 2006 -0500
Fixed initrd issue by define big RAM
Signed-off-by:Jason Jin <Jason.jin@freescale.com>
commit e6cd2a1785d74ec3d30a86f1cb360be8de478151
Author: Jason Jin <Jason.jin@freescale.com>
Date: Fri Jul 7 10:01:45 2006 -0500
We made a u-boot patch to fix the hang up issue
when booting filesystem from ramdisk.
Signed-off-by:Jason Jin <Jason.jin@freescale.com>
commit 38433ccc5850ee70549af0b2bc5b920355ef5388
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:47:03 2006 -0500
* Switched default PCI speed for 8540 ADS back to 33MHz
* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit e4c2a0eb0c3e3ffbf824800184ee42bdc99d5b19
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:46:35 2006 -0500
* Fixed a bug where 8555 PCI code used the old variable and
function names
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit cbfc7ce756b88eb26e5537bc7b625c445c6dcfac
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:46:13 2006 -0500
* Added VIA configuration table
* Added support for PCI2 on CDS
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 52c7a68b8d587ebcf5a6b051b58b3d3ffa377ddc
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:45:41 2006 -0500
* Fixed PCI memory definitions
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 087454609e47295443af793a282cddcd91a5f49c
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:45:17 2006 -0500
* Added support for initializing second PCI bus on 85xx
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit b636aaeb6fd516a442fb611bbeeddf3077a687fb
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:44:49 2006 -0500
* Added PCI-X #defines for PCI-X initialization
Patch by Andy Fleming on 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 20abbc6fffa115690107cc942c7abf84bdc03a1b
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:44:23 2006 -0500
* Made sure the code which disables prefetch for PCI devices
sets the size of the prefetch region to 0
Patch by Andy Fleming on 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit 40d5fa35d02df22580593bf0039ab173367e8ef0
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:43:36 2006 -0500
* Add Flat Dev Tree construction for MPC85xx ADS and CDS boards
Patch by Jon Loeliger 17-Jan-2006
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit be7e8b0cb5a0c49dc180075b96df296a893bf146
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:43:00 2006 -0500
* Removed the oftree.dts for stxxtx in light of the changes
to the flat device tree handling code
Patch by Matthew McClintock 26-June-2006
commit 1b380ec225665e73959677f3893dc658c5925e05
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:42:24 2006 -0500
* Patch to modify ft_build.c to update flat device trees in place
Patch by Matthew McClintock 26-June-2006
commit 98a9c4d468a942a09ebe8979bec508017f3e4462
Author: Matthew McClintock <msm@freescale.com>
Date: Wed Jun 28 10:41:37 2006 -0500
* Modify bootm command to support booting with flat device trees
Patch by Matthew McClintock 26-June-2006
commit da012ab661fd4ab169dd7b9b32201a4df62cf34a
Author: Jin Zhengxiong <Jason.Jin@freescale.com>
Date: Wed Jun 28 08:43:56 2006 -0500
Change Id to symbolic name for RTL8139
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit bc09cf3c2bfb8d54c659cbb332f79d0950982fd0
Author: Jin Zhengxiong-R64188 <Jason.Jin@freescale.com>
Date: Tue Jun 27 18:12:10 2006 +0800
Fix RTL8139 in big endian
signed-off-by: Jason Jin <Jason.Jin@freescale.com>
signed-off-by: Wei Zhang <wei.zhang@freescale.com>
commit fcfb9a57947fc203b99fe81ab0578f7286261f9f
Author: Jin Zhengxiong-R64188 <Jason.Jin@freescale.com>
Date: Tue Jun 27 18:12:23 2006 +0800
Fix Tsec bug when no link
When tftp a non-exist file from the tftp server, u-boot will check
the link of all eth port. The original file will return wrong link
state on the no link ports.
signed-off-by: Jason Jin <Jason.Jin@freescale.com>
commit bd22c2b97514fbfb0e03bd9c72b3445e4dbd57e2
Author: Jin Zhengxiong-R64188 <Jason.Jin@freescale.com>
Date: Tue Jun 27 18:12:02 2006 +0800
Fix bug for io_bar size during pci scan
During the pci scan process, Some devices return bar_reponse with the
highest bytes 0, such as the pci bridge in uli1575 return bar_response
with 0xffffff, So the bar_size should be manually set under 64K.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
commit fa7db9c377bc2353a17bf1d381d65a6c418728f0
Author: Jin Zhengxiong-R64188 <Jason.Jin@freescale.com>
Date: Tue Jun 27 18:11:54 2006 +0800
Enable PCIE1 for MPC8641HPCN board
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
commit 99d70e3a47affb9bae041a2caece7cd516e213b3
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Mon Jun 26 11:06:00 2006 +0200
More code cleanup
commit 684623ce92c5fd32e7db2d6e016945a67c5ffaba
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Jun 22 08:51:46 2006 -0500
Fix bug in 8641hpcn reset command with no args.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
commit 8be429a5ddbf0ebe2d94174ba58fcfc7a24285dc
Author: Zhang Wei <wei.zhang@freescale.com>
Date: Tue Jun 20 17:47:15 2006 +0800
Reworked IRQ mapping in OF-tree.
commit 0e4c2a17ca34001ed36d259f13cb88ada4611a8c
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Jun 15 21:33:37 2006 -0500
Do not enable address translation on secondary CPUs.
Do not set up BATs on secondary CPUs. Let Linux do the nasty.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 386eda022473394ad8f36b86f2bdc9b4cb816291
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Jun 14 18:14:56 2006 +0200
Code cleanup
commit 16c8d5e76ae0f78f39a60608574adfe0feb9cc70
Author: Wolfgang Denk <wd@pollux.denx.de>
Date: Wed Jun 14 17:45:53 2006 +0200
Various USB related patches
- Add support for mpc8xx USB device.
- Add support for Common Device Class - Abstract Control Model USB console.
- Add support for flow control in USB slave devices.
- Add support for switching between gserial and cdc_acm using environment.
- Minor changes to usbdcore_omap1510.c usbdcore_omap1510.h
- Update usbcore slightly to ease host enumeration.
- Fix non-portable endian problems in usbdcore and usbdcore_ep0.
- Add AdderUSB_config as a defconfig to enable usage of the USB console
by default with the Adder87x U-Boot port.
Patches by Bryan O'Donoghue <bodonoghue@codehermit.ie>, 29 May 2006
commit 8ecc971618f56029ad99d3516f8b297a6ed58971
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 7 10:53:55 2006 -0500
Fix a get_board_sys_clk() use-before-def warning.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit d9bf4858fca5aa4d651b283270f77da72ebadfd5
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed Jun 7 10:52:49 2006 -0500
Allow DTC path to be passed in.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit c83ae9ea6d93abbe751bf8a3396236a084e56f87
Author: Haiying Wang <haiying.wang@freescale.com>
Date: Tue Jun 6 16:54:29 2006 -0400
Modify the IRQ of DUART2
commit c934f655f9aeca70a5c5f88b465d9e9d57a8d22e
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed May 31 13:55:35 2006 -0500
Review cleanups.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit cb5965fb95b77a49f4e6af95248e0c849f4af03e
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed May 31 12:44:44 2006 -0500
White space cleanup.
Some 80-column cleanups.
Convert printf() to puts() where possible.
Use #include "spd_sdram.h" as needed.
Enhanced reset command usage message a bit.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 3d5c5be547445dd3bd2eb7368d80df03ea437970
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed May 31 11:39:34 2006 -0500
Removed unneeded local_bus_init() from 8641HPCN board.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit 4d3d729c16c392d2982d3266b659d333c927697d
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed May 31 11:24:28 2006 -0500
Moved mpc8641hpcn_board_reset() out of cpu/ into board/.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit b2a941de060350ad15878d8219825f4950e9bb8e
Author: Jon Loeliger <jdl@jdl.com>
Date: Wed May 31 10:07:28 2006 -0500
Remove dead debug code.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit 126aa70f10ba3d20e0a6f4d32328250513b77770
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue May 30 17:47:00 2006 -0500
Move mpc86xx PIXIS code to board directory
First cut at moving the PIXIS platform code out of
the 86xx cpu directory and into board/mpc8641hpcn
where it belongs.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
commit ddf83a2fcef1a670c45fc585119dcc1fe062c4a9
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue May 30 16:56:14 2006 +0200
Support generic OHCI support for the s3c24x0 cpu.
commit 38cee12dcfcc257371c901c7e13e58ecab0a35d8
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Tue May 30 09:10:32 2006 -0500
Improve "reset" command's interaction with watchdog.
"reset altbank" will reset another bank WITHOUT watch dog timer enabled
"reset altbank wd" will reset another bank WITH watch dog enabled
"diswd" will disable watch dog after u-boot boots up successfully
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit 70205e5a6ddc8528b11db9eb4d3fa0209d9fce2a
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Tue May 30 08:51:19 2006 -0500
Fix two SDRAM setup bugs.
Fix ECC setup bug.
Enable 1T/2T based on number of DIMMs present.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit d11fec5015334deb2010e36ce00bb118cc5429a5
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Fri May 26 10:24:48 2006 -0500
Add first draft of the MPC8641HPCN doc/README.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit ed45d6c930b5939718a87ee12e25cf9a05978d4a
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Fri May 26 10:13:04 2006 -0500
Added pci@8000 block.
Updated ethernet interrupt mappings (moved up 48).
Cleaned up a few comments.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit 3033ebb20fd7c372c7bca3c9955a4692bb2240b7
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Fri May 26 10:01:16 2006 -0500
Allow args on reset command.
Signed-off-by: Jon Loeliger <jdl@jdl.com>
commit 301f1aa384d0edcae6a22fd9adb933ad71695ecc
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue May 23 13:38:35 2006 +0200
Changed the mp2usb (at91rm9200) board to use the generic OHCI driver. Some
fixes to the latter.
commit 24e37645e7378b20fa8f20e2996c8fb8e90c70c9
Author: Markus Klotzbuecher <mk@denx.de>
Date: Tue May 23 10:33:11 2006 +0200
More cleanup for the delta board and the generic usb_ohci driver. Added
CFG_USB_BOARD_INIT and CFG_USB_CPU_INIT for enabling board and cpu specific
initialization and cleanup hooks respectively.
commit 3e326ece9eba8184f5d48aa4fb87760a8f6f0f10
Author: Markus Klotzbuecher <mk@denx.de>
Date: Mon May 22 16:33:54 2006 +0200
This patch adds USB storage support for the delta board. This is the first
board to make use of a generic OHCI driver, that calls hooks for board
dependant initialization.
commit 14e37081ff3cac7ebe6e93836523429853b6b292
Author: Jon Loeliger <jdl@jdl.com>
Date: Fri May 19 13:28:39 2006 -0500
Change arbitration to round-robin for SMP linux.
commit 9a655876e5995be80f49054e2509500e871e4d3a
Author: Jon Loeliger <jdl@jdl.com>
Date: Fri May 19 13:26:34 2006 -0500
Enable dual DDR controllers and interleaving.
commit 586d1d5abd3e525f1e1d9b81e5a61a4da6b2fa3c
Author: Jon Loeliger <jdl@jdl.com>
Date: Fri May 19 13:22:44 2006 -0500
Update 86xx address map and LAWBARs.
commit cccce5d0581bb0ba4602799a4b5112e58d1579cb
Author: Jon Loeliger <jdl@jdl.com>
Date: Fri May 19 13:14:15 2006 -0500
Remove L2 Cache invalidate polling.
commit f35ec68fb066cec0e36294bfe07dec2d4e8ad3a8
Author: Jon Loeliger <jdl@jdl.com>
Date: Fri May 19 12:33:09 2006 -0500
Enable 2nd CPU and I2C.
commit bf690dcb512d34c4fceec0eb1e5c0e88a9db5d54
Author: Jon Loeliger <jdl@freescale.com>
Date: Mon May 15 07:26:56 2006 -0500
Update interrupt mapping.
commit 6cfea33477b04b63ed47386ed1629529484c33ba
Author: Haiying Wang <Haiying.Wang@freescale.com>
Date: Wed May 10 09:38:06 2006 -0500
Remove unneeded INIT_RAM_LOCK cache twiddling.
Correctly tracks r29 as global data pointer now.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
commit d4dd317b58c126a2a7e73f4764ecc1a7c97f876c
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed May 10 09:33:07 2006 -0500
Remove unnecessary flash.c file.
commit 18b6c8cd8af6cc7f35180cedc4adb3236cc1a1b8
Author: Jon Loeliger <jdl@freescale.com>
Date: Tue May 9 08:23:49 2006 -0500
Get MPC8641HPCN flash images working.
Enable the CFI driver.
Remove bogus LAWBAR7 cruft.
Use correct TEXT_BASE, Fixup load script.
Enable SPD EEPROM during DDR setup.
Use generic RFC 1918 IP addresses by default.
commit 5c9efb36a6b5431423f52888a0e3b4b515fe7eca
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Apr 27 10:15:16 2006 -0500
Cleanup whitespaces and style issues.
Removed //-style comments.
Use 80-column lines.
Remove trailing whitespace.
Remove dead code and debug cruft.
commit a2320a6bf8113a09544c42d160d10ac69d049a03
Author: Jon Loeliger <jdl@freescale.com>
Date: Thu Apr 27 08:22:39 2006 -0500
Revert bad PCI prefetch limit change.
commit debb7354d1ea4f694154818df5e5b523f5c1cc1d
Author: Jon Loeliger <jdl@freescale.com>
Date: Wed Apr 26 17:58:56 2006 -0500
Initial support for MPC8641 HPCN board.