upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
339 lines
8.2 KiB
339 lines
8.2 KiB
/*
|
|
* (C) Copyright 2010
|
|
* Stefano Babic, DENX Software Engineering, sbabic@denx.de
|
|
*
|
|
* Based on da850evm.c, original Copyrights follow:
|
|
*
|
|
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* Based on da830evm.c. Original Copyrights follow:
|
|
*
|
|
* Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
|
|
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <asm/arch/hardware.h>
|
|
#include <asm/ti-common/davinci_nand.h>
|
|
#include <asm/arch/emac_defs.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/davinci_misc.h>
|
|
#include <asm/gpio.h>
|
|
#include "../../../drivers/video/da8xx-fb.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
static const struct da8xx_panel lcd_panel = {
|
|
/* Casio COM57H531x */
|
|
.name = "Casio_COM57H531x",
|
|
.width = 640,
|
|
.height = 480,
|
|
.hfp = 12,
|
|
.hbp = 144,
|
|
.hsw = 30,
|
|
.vfp = 10,
|
|
.vbp = 35,
|
|
.vsw = 3,
|
|
.pxl_clk = 25000000,
|
|
.invert_pxl_clk = 0,
|
|
};
|
|
|
|
static const struct display_panel disp_panel = {
|
|
QVGA,
|
|
16,
|
|
16,
|
|
COLOR_ACTIVE,
|
|
};
|
|
|
|
static const struct lcd_ctrl_config lcd_cfg = {
|
|
&disp_panel,
|
|
.ac_bias = 255,
|
|
.ac_bias_intrpt = 0,
|
|
.dma_burst_sz = 16,
|
|
.bpp = 16,
|
|
.fdd = 255,
|
|
.tft_alt_mode = 0,
|
|
.stn_565_mode = 0,
|
|
.mono_8bit_mode = 0,
|
|
.invert_line_clock = 1,
|
|
.invert_frm_clock = 1,
|
|
.sync_edge = 0,
|
|
.sync_ctrl = 1,
|
|
.raster_order = 0,
|
|
};
|
|
|
|
/* SPI0 pin muxer settings */
|
|
static const struct pinmux_config spi1_pins[] = {
|
|
{ pinmux(5), 1, 1 },
|
|
{ pinmux(5), 1, 2 },
|
|
{ pinmux(5), 1, 4 },
|
|
{ pinmux(5), 1, 5 }
|
|
};
|
|
|
|
/* I2C pin muxer settings */
|
|
static const struct pinmux_config i2c_pins[] = {
|
|
{ pinmux(4), 2, 2 },
|
|
{ pinmux(4), 2, 3 }
|
|
};
|
|
|
|
/* UART0 pin muxer settings */
|
|
static const struct pinmux_config uart_pins[] = {
|
|
{ pinmux(3), 2, 7 },
|
|
{ pinmux(3), 2, 6 },
|
|
{ pinmux(3), 2, 4 },
|
|
{ pinmux(3), 2, 5 }
|
|
};
|
|
|
|
#ifdef CONFIG_DRIVER_TI_EMAC
|
|
#define HAS_RMII 1
|
|
static const struct pinmux_config emac_pins[] = {
|
|
{ pinmux(14), 8, 2 },
|
|
{ pinmux(14), 8, 3 },
|
|
{ pinmux(14), 8, 4 },
|
|
{ pinmux(14), 8, 5 },
|
|
{ pinmux(14), 8, 6 },
|
|
{ pinmux(14), 8, 7 },
|
|
{ pinmux(15), 8, 1 },
|
|
{ pinmux(4), 8, 0 },
|
|
{ pinmux(4), 8, 1 }
|
|
};
|
|
#endif
|
|
|
|
#ifdef CONFIG_NAND_DAVINCI
|
|
const struct pinmux_config nand_pins[] = {
|
|
{ pinmux(7), 1, 0}, /* CS2 */
|
|
{ pinmux(7), 0, 1}, /* CS3 in three state*/
|
|
{ pinmux(7), 1, 4 }, /* EMA_WE */
|
|
{ pinmux(7), 1, 5 }, /* EMA_OE */
|
|
{ pinmux(9), 1, 0 }, /* EMA_D[7] */
|
|
{ pinmux(9), 1, 1 }, /* EMA_D[6] */
|
|
{ pinmux(9), 1, 2 }, /* EMA_D[5] */
|
|
{ pinmux(9), 1, 3 }, /* EMA_D[4] */
|
|
{ pinmux(9), 1, 4 }, /* EMA_D[3] */
|
|
{ pinmux(9), 1, 5 }, /* EMA_D[2] */
|
|
{ pinmux(9), 1, 6 }, /* EMA_D[1] */
|
|
{ pinmux(9), 1, 7 }, /* EMA_D[0] */
|
|
{ pinmux(12), 1, 5 }, /* EMA_A[2] */
|
|
{ pinmux(12), 1, 6 }, /* EMA_A[1] */
|
|
{ pinmux(6), 1, 0 } /* EMA_CLK */
|
|
};
|
|
#endif
|
|
|
|
const struct pinmux_config gpio_pins[] = {
|
|
{ pinmux(13), 8, 0 }, /* GPIO6[15] RESETOUTn on SOM*/
|
|
{ pinmux(13), 8, 5 }, /* GPIO6[10] U0_SW0 on EA20-00101_2*/
|
|
{ pinmux(13), 8, 3 }, /* GPIO6[12] U0_SW1 on EA20-00101_2*/
|
|
{ pinmux(19), 8, 5 }, /* GPIO6[1] DISP_ON */
|
|
{ pinmux(14), 8, 1 } /* GPIO6[6] LCD_B_PWR*/
|
|
};
|
|
|
|
const struct pinmux_config lcd_pins[] = {
|
|
{ pinmux(17), 2, 1 }, /* LCD_D_0 */
|
|
{ pinmux(17), 2, 0 }, /* LCD_D_1 */
|
|
{ pinmux(16), 2, 7 }, /* LCD_D_2 */
|
|
{ pinmux(16), 2, 6 }, /* LCD_D_3 */
|
|
{ pinmux(16), 2, 5 }, /* LCD_D_4 */
|
|
{ pinmux(16), 2, 4 }, /* LCD_D_5 */
|
|
{ pinmux(16), 2, 3 }, /* LCD_D_6 */
|
|
{ pinmux(16), 2, 2 }, /* LCD_D_7 */
|
|
{ pinmux(18), 2, 1 }, /* LCD_D_8 */
|
|
{ pinmux(18), 2, 0 }, /* LCD_D_9 */
|
|
{ pinmux(17), 2, 7 }, /* LCD_D_10 */
|
|
{ pinmux(17), 2, 6 }, /* LCD_D_11 */
|
|
{ pinmux(17), 2, 5 }, /* LCD_D_12 */
|
|
{ pinmux(17), 2, 4 }, /* LCD_D_13 */
|
|
{ pinmux(17), 2, 3 }, /* LCD_D_14 */
|
|
{ pinmux(17), 2, 2 }, /* LCD_D_15 */
|
|
{ pinmux(18), 2, 6 }, /* LCD_PCLK */
|
|
{ pinmux(19), 2, 0 }, /* LCD_HSYNC */
|
|
{ pinmux(19), 2, 1 }, /* LCD_VSYNC */
|
|
{ pinmux(19), 2, 6 }, /* DA850_NLCD_AC_ENB_CS */
|
|
};
|
|
|
|
const struct pinmux_config halten_pin[] = {
|
|
{ pinmux(3), 4, 2 } /* GPIO8[6] HALTEN */
|
|
};
|
|
|
|
static const struct pinmux_resource pinmuxes[] = {
|
|
#ifdef CONFIG_SPI_FLASH
|
|
PINMUX_ITEM(spi1_pins),
|
|
#endif
|
|
PINMUX_ITEM(uart_pins),
|
|
PINMUX_ITEM(i2c_pins),
|
|
#ifdef CONFIG_NAND_DAVINCI
|
|
PINMUX_ITEM(nand_pins),
|
|
#endif
|
|
#ifdef CONFIG_VIDEO
|
|
PINMUX_ITEM(lcd_pins),
|
|
#endif
|
|
};
|
|
|
|
static const struct lpsc_resource lpsc[] = {
|
|
{ DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
|
|
{ DAVINCI_LPSC_SPI1 }, /* Serial Flash */
|
|
{ DAVINCI_LPSC_EMAC }, /* image download */
|
|
{ DAVINCI_LPSC_UART0 }, /* console */
|
|
{ DAVINCI_LPSC_GPIO },
|
|
{ DAVINCI_LPSC_LCDC }, /* LCD */
|
|
};
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
/* PinMux for GPIO */
|
|
if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
|
|
return 1;
|
|
|
|
/* Set DISP_ON high to enable LCD output*/
|
|
gpio_direction_output(97, 1);
|
|
|
|
/* Set the RESETOUTn low */
|
|
gpio_direction_output(111, 0);
|
|
|
|
/* Set U0_SW0 low for UART0 as console*/
|
|
gpio_direction_output(106, 0);
|
|
|
|
/* Set U0_SW1 low for UART0 as console*/
|
|
gpio_direction_output(108, 0);
|
|
|
|
/* Set LCD_B_PWR low to power down LCD Backlight*/
|
|
gpio_direction_output(102, 0);
|
|
|
|
#ifndef CONFIG_USE_IRQ
|
|
irq_init();
|
|
#endif
|
|
|
|
/*
|
|
* NAND CS setup - cycle counts based on da850evm NAND timings in the
|
|
* Linux kernel @ 25MHz EMIFA
|
|
*/
|
|
#ifdef CONFIG_NAND_DAVINCI
|
|
writel((DAVINCI_ABCR_WSETUP(0) |
|
|
DAVINCI_ABCR_WSTROBE(1) |
|
|
DAVINCI_ABCR_WHOLD(0) |
|
|
DAVINCI_ABCR_RSETUP(0) |
|
|
DAVINCI_ABCR_RSTROBE(1) |
|
|
DAVINCI_ABCR_RHOLD(0) |
|
|
DAVINCI_ABCR_TA(0) |
|
|
DAVINCI_ABCR_ASIZE_8BIT),
|
|
&davinci_emif_regs->ab1cr); /* CS2 */
|
|
#endif
|
|
|
|
/*
|
|
* Power on required peripherals
|
|
* ARM does not have access by default to PSC0 and PSC1
|
|
* assuming here that the DSP bootloader has set the IOPU
|
|
* such that PSC access is available to ARM
|
|
*/
|
|
if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
|
|
return 1;
|
|
|
|
/* setup the SUSPSRC for ARM to control emulation suspend */
|
|
writel(readl(&davinci_syscfg_regs->suspsrc) &
|
|
~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
|
|
DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
|
|
DAVINCI_SYSCFG_SUSPSRC_UART0),
|
|
&davinci_syscfg_regs->suspsrc);
|
|
|
|
/* configure pinmux settings */
|
|
if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
|
|
return 1;
|
|
|
|
#ifdef CONFIG_DRIVER_TI_EMAC
|
|
if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0)
|
|
return 1;
|
|
|
|
davinci_emac_mii_mode_sel(HAS_RMII);
|
|
#endif /* CONFIG_DRIVER_TI_EMAC */
|
|
|
|
/* enable the console UART */
|
|
writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
|
|
DAVINCI_UART_PWREMU_MGMT_UTRST),
|
|
&davinci_uart0_ctrl_regs->pwremu_mgmt);
|
|
|
|
/*
|
|
* Reconfigure the LCDC priority to the highest to ensure that
|
|
* the throughput/latency requirements for the LCDC are met.
|
|
*/
|
|
writel(readl(&davinci_syscfg_regs->mstpri[2]) & 0x0fffffff,
|
|
&davinci_syscfg_regs->mstpri[2]);
|
|
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Do not overwrite the console
|
|
* Use always serial for U-Boot console
|
|
*/
|
|
int overwrite_console(void)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* arch number of the board */
|
|
gd->bd->bi_arch_number = MACH_TYPE_EA20;
|
|
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
|
|
|
|
da8xx_video_init(&lcd_panel, &lcd_cfg, 16);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_BOARD_LATE_INIT
|
|
|
|
int board_late_init(void)
|
|
{
|
|
unsigned char buf[2];
|
|
int ret;
|
|
|
|
/* PinMux for HALTEN */
|
|
if (davinci_configure_pin_mux(halten_pin, ARRAY_SIZE(halten_pin)) != 0)
|
|
return 1;
|
|
|
|
/* Set HALTEN to high */
|
|
gpio_direction_output(134, 1);
|
|
|
|
/* Set fixed contrast settings for LCD via I2C potentiometer */
|
|
buf[0] = 0x00;
|
|
buf[1] = 0xd7;
|
|
ret = i2c_write(0x2e, 6, 1, buf, 2);
|
|
if (ret)
|
|
puts("\nContrast Settings FAILED\n");
|
|
|
|
/* Set LCD_B_PWR high to power up LCD Backlight*/
|
|
gpio_set_value(102, 1);
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_BOARD_LATE_INIT */
|
|
|
|
#ifdef CONFIG_DRIVER_TI_EMAC
|
|
|
|
/*
|
|
* Initializes on-board ethernet controllers.
|
|
*/
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
if (!davinci_emac_initialize()) {
|
|
printf("Error: Ethernet init failed!\n");
|
|
return -1;
|
|
}
|
|
|
|
/*
|
|
* This board has a RMII PHY. However, the MDC line on the SOM
|
|
* must not be disabled (there is no MII PHY on the
|
|
* baseboard) via the GPIO2[6], because this pin
|
|
* disables at the same time the SPI flash.
|
|
*/
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_DRIVER_TI_EMAC */
|
|
|