upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
148 lines
3.6 KiB
148 lines
3.6 KiB
/*
|
|
* Copyright (C) Marvell International Ltd. and its affiliates
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <spl.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
#include "ddr3_init.h"
|
|
|
|
#define REG_READ_DATA_SAMPLE_DELAYS_ADDR 0x1538
|
|
#define REG_READ_DATA_SAMPLE_DELAYS_MASK 0x1f
|
|
#define REG_READ_DATA_SAMPLE_DELAYS_OFFS 8
|
|
|
|
#define REG_READ_DATA_READY_DELAYS_ADDR 0x153c
|
|
#define REG_READ_DATA_READY_DELAYS_MASK 0x1f
|
|
#define REG_READ_DATA_READY_DELAYS_OFFS 8
|
|
|
|
int ddr3_if_ecc_enabled(void)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (DDR3_IS_ECC_PUP4_MODE(tm->bus_act_mask) ||
|
|
DDR3_IS_ECC_PUP3_MODE(tm->bus_act_mask))
|
|
return 1;
|
|
else
|
|
return 0;
|
|
}
|
|
|
|
int ddr3_pre_algo_config(void)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
/* Set Bus3 ECC training mode */
|
|
if (DDR3_IS_ECC_PUP3_MODE(tm->bus_act_mask)) {
|
|
/* Set Bus3 ECC MUX */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(0, ACCESS_TYPE_UNICAST, PARAM_NOT_CARE,
|
|
REG_SDRAM_PINS_MUX, 0x100, 0x100));
|
|
}
|
|
|
|
/* Set regular ECC training mode (bus4 and bus 3) */
|
|
if ((DDR3_IS_ECC_PUP4_MODE(tm->bus_act_mask)) ||
|
|
(DDR3_IS_ECC_PUP3_MODE(tm->bus_act_mask))) {
|
|
/* Enable ECC Write MUX */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(0, ACCESS_TYPE_UNICAST, PARAM_NOT_CARE,
|
|
TRAINING_SW_2_REG, 0x100, 0x100));
|
|
/* General ECC enable */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(0, ACCESS_TYPE_UNICAST, PARAM_NOT_CARE,
|
|
REG_SDRAM_CONFIG_ADDR, 0x40000, 0x40000));
|
|
/* Disable Read Data ECC MUX */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(0, ACCESS_TYPE_UNICAST, PARAM_NOT_CARE,
|
|
TRAINING_SW_2_REG, 0x0, 0x2));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
int ddr3_post_algo_config(void)
|
|
{
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
int status;
|
|
|
|
status = ddr3_post_run_alg();
|
|
if (MV_OK != status) {
|
|
printf("DDR3 Post Run Alg - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
/* Un_set ECC training mode */
|
|
if ((DDR3_IS_ECC_PUP4_MODE(tm->bus_act_mask)) ||
|
|
(DDR3_IS_ECC_PUP3_MODE(tm->bus_act_mask))) {
|
|
/* Disable ECC Write MUX */
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(0, ACCESS_TYPE_UNICAST, PARAM_NOT_CARE,
|
|
TRAINING_SW_2_REG, 0x0, 0x100));
|
|
/* General ECC and Bus3 ECC MUX remains enabled */
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
int ddr3_hws_hw_training(void)
|
|
{
|
|
enum hws_algo_type algo_mode = ALGO_TYPE_DYNAMIC;
|
|
int status;
|
|
struct init_cntr_param init_param;
|
|
|
|
status = ddr3_silicon_pre_init();
|
|
if (MV_OK != status) {
|
|
printf("DDR3 Pre silicon Config - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
init_param.do_mrs_phy = 1;
|
|
#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)
|
|
init_param.is_ctrl64_bit = 0;
|
|
#else
|
|
init_param.is_ctrl64_bit = 1;
|
|
#endif
|
|
#if defined(CONFIG_ALLEYCAT3) || defined(CONFIG_ARMADA_38X) || \
|
|
defined(CONFIG_ARMADA_39X)
|
|
init_param.init_phy = 1;
|
|
#else
|
|
init_param.init_phy = 0;
|
|
#endif
|
|
init_param.msys_init = 1;
|
|
status = hws_ddr3_tip_init_controller(0, &init_param);
|
|
if (MV_OK != status) {
|
|
printf("DDR3 init controller - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
status = ddr3_silicon_post_init();
|
|
if (MV_OK != status) {
|
|
printf("DDR3 Post Init - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
status = ddr3_pre_algo_config();
|
|
if (MV_OK != status) {
|
|
printf("DDR3 Pre Algo Config - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
/* run algorithm in order to configure the PHY */
|
|
status = hws_ddr3_tip_run_alg(0, algo_mode);
|
|
if (MV_OK != status) {
|
|
printf("DDR3 run algorithm - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
status = ddr3_post_algo_config();
|
|
if (MV_OK != status) {
|
|
printf("DDR3 Post Algo Config - FAILED 0x%x\n", status);
|
|
return status;
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|