upstream u-boot with additional patches for our devices/boards:
https://lists.denx.de/pipermail/u-boot/2017-March/282789.html (AXP crashes) ;
Gbit ethernet patch for some LIME2 revisions ;
with SPI flash support
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
289 lines
7.8 KiB
289 lines
7.8 KiB
/*
|
|
* Copyright (C) Marvell International Ltd. and its affiliates
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <spl.h>
|
|
#include <asm/io.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
|
|
#include "ddr3_init.h"
|
|
|
|
static u32 bist_offset = 32;
|
|
enum hws_pattern sweep_pattern = PATTERN_KILLER_DQ0;
|
|
|
|
static int ddr3_tip_bist_operation(u32 dev_num,
|
|
enum hws_access_type access_type,
|
|
u32 if_id,
|
|
enum hws_bist_operation oper_type);
|
|
|
|
/*
|
|
* BIST activate
|
|
*/
|
|
int ddr3_tip_bist_activate(u32 dev_num, enum hws_pattern pattern,
|
|
enum hws_access_type access_type, u32 if_num,
|
|
enum hws_dir direction,
|
|
enum hws_stress_jump addr_stress_jump,
|
|
enum hws_pattern_duration duration,
|
|
enum hws_bist_operation oper_type,
|
|
u32 offset, u32 cs_num, u32 pattern_addr_length)
|
|
{
|
|
u32 tx_burst_size;
|
|
u32 delay_between_burst;
|
|
u32 rd_mode, val;
|
|
u32 poll_cnt = 0, max_poll = 1000, i, start_if, end_if;
|
|
struct pattern_info *pattern_table = ddr3_tip_get_pattern_table();
|
|
u32 read_data[MAX_INTERFACE_NUM];
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
/* ODPG Write enable from BIST */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_num,
|
|
ODPG_DATA_CONTROL_REG, 0x1, 0x1));
|
|
/* ODPG Read enable/disable from BIST */
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_num,
|
|
ODPG_DATA_CONTROL_REG,
|
|
(direction == OPER_READ) ?
|
|
0x2 : 0, 0x2));
|
|
CHECK_STATUS(ddr3_tip_load_pattern_to_odpg(dev_num, access_type, if_num,
|
|
pattern, offset));
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_num,
|
|
ODPG_DATA_BUF_SIZE_REG,
|
|
pattern_addr_length, MASK_ALL_BITS));
|
|
tx_burst_size = (direction == OPER_WRITE) ?
|
|
pattern_table[pattern].tx_burst_size : 0;
|
|
delay_between_burst = (direction == OPER_WRITE) ? 2 : 0;
|
|
rd_mode = (direction == OPER_WRITE) ? 1 : 0;
|
|
CHECK_STATUS(ddr3_tip_configure_odpg
|
|
(dev_num, access_type, if_num, direction,
|
|
pattern_table[pattern].num_of_phases_tx, tx_burst_size,
|
|
pattern_table[pattern].num_of_phases_rx,
|
|
delay_between_burst,
|
|
rd_mode, cs_num, addr_stress_jump, duration));
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_num,
|
|
ODPG_PATTERN_ADDR_OFFSET_REG,
|
|
offset, MASK_ALL_BITS));
|
|
if (oper_type == BIST_STOP) {
|
|
CHECK_STATUS(ddr3_tip_bist_operation(dev_num, access_type,
|
|
if_num, BIST_STOP));
|
|
} else {
|
|
CHECK_STATUS(ddr3_tip_bist_operation(dev_num, access_type,
|
|
if_num, BIST_START));
|
|
if (duration != DURATION_CONT) {
|
|
/*
|
|
* This pdelay is a WA, becuase polling fives "done"
|
|
* also the odpg did nmot finish its task
|
|
*/
|
|
if (access_type == ACCESS_TYPE_MULTICAST) {
|
|
start_if = 0;
|
|
end_if = MAX_INTERFACE_NUM - 1;
|
|
} else {
|
|
start_if = if_num;
|
|
end_if = if_num;
|
|
}
|
|
|
|
for (i = start_if; i <= end_if; i++) {
|
|
VALIDATE_ACTIVE(tm->
|
|
if_act_mask, i);
|
|
|
|
for (poll_cnt = 0; poll_cnt < max_poll;
|
|
poll_cnt++) {
|
|
CHECK_STATUS(ddr3_tip_if_read
|
|
(dev_num,
|
|
ACCESS_TYPE_UNICAST,
|
|
if_num, ODPG_BIST_DONE,
|
|
read_data,
|
|
MASK_ALL_BITS));
|
|
val = read_data[i];
|
|
if ((val & 0x1) == 0x0) {
|
|
/*
|
|
* In SOC type devices this bit
|
|
* is self clear so, if it was
|
|
* cleared all good
|
|
*/
|
|
break;
|
|
}
|
|
}
|
|
|
|
if (poll_cnt >= max_poll) {
|
|
DEBUG_TRAINING_BIST_ENGINE
|
|
(DEBUG_LEVEL_ERROR,
|
|
("Bist poll failure 2\n"));
|
|
CHECK_STATUS(ddr3_tip_if_write
|
|
(dev_num,
|
|
ACCESS_TYPE_UNICAST,
|
|
if_num,
|
|
ODPG_DATA_CONTROL_REG, 0,
|
|
MASK_ALL_BITS));
|
|
return MV_FAIL;
|
|
}
|
|
}
|
|
|
|
CHECK_STATUS(ddr3_tip_bist_operation
|
|
(dev_num, access_type, if_num, BIST_STOP));
|
|
}
|
|
}
|
|
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_num,
|
|
ODPG_DATA_CONTROL_REG, 0,
|
|
MASK_ALL_BITS));
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* BIST read result
|
|
*/
|
|
int ddr3_tip_bist_read_result(u32 dev_num, u32 if_id,
|
|
struct bist_result *pst_bist_result)
|
|
{
|
|
int ret;
|
|
u32 read_data[MAX_INTERFACE_NUM];
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
if (IS_ACTIVE(tm->if_act_mask, if_id) == 0)
|
|
return MV_NOT_SUPPORTED;
|
|
DEBUG_TRAINING_BIST_ENGINE(DEBUG_LEVEL_TRACE,
|
|
("ddr3_tip_bist_read_result if_id %d\n",
|
|
if_id));
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ODPG_BIST_FAILED_DATA_HI_REG, read_data,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
pst_bist_result->bist_fail_high = read_data[if_id];
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ODPG_BIST_FAILED_DATA_LOW_REG, read_data,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
pst_bist_result->bist_fail_low = read_data[if_id];
|
|
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ODPG_BIST_LAST_FAIL_ADDR_REG, read_data,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
pst_bist_result->bist_last_fail_addr = read_data[if_id];
|
|
ret = ddr3_tip_if_read(dev_num, ACCESS_TYPE_UNICAST, if_id,
|
|
ODPG_BIST_DATA_ERROR_COUNTER_REG, read_data,
|
|
MASK_ALL_BITS);
|
|
if (ret != MV_OK)
|
|
return ret;
|
|
pst_bist_result->bist_error_cnt = read_data[if_id];
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* BIST flow - Activate & read result
|
|
*/
|
|
int hws_ddr3_run_bist(u32 dev_num, enum hws_pattern pattern, u32 *result,
|
|
u32 cs_num)
|
|
{
|
|
int ret;
|
|
u32 i = 0;
|
|
u32 win_base;
|
|
struct bist_result st_bist_result;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (i = 0; i < MAX_INTERFACE_NUM; i++) {
|
|
VALIDATE_ACTIVE(tm->if_act_mask, i);
|
|
hws_ddr3_cs_base_adr_calc(i, cs_num, &win_base);
|
|
ret = ddr3_tip_bist_activate(dev_num, pattern,
|
|
ACCESS_TYPE_UNICAST,
|
|
i, OPER_WRITE, STRESS_NONE,
|
|
DURATION_SINGLE, BIST_START,
|
|
bist_offset + win_base,
|
|
cs_num, 15);
|
|
if (ret != MV_OK) {
|
|
printf("ddr3_tip_bist_activate failed (0x%x)\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ddr3_tip_bist_activate(dev_num, pattern,
|
|
ACCESS_TYPE_UNICAST,
|
|
i, OPER_READ, STRESS_NONE,
|
|
DURATION_SINGLE, BIST_START,
|
|
bist_offset + win_base,
|
|
cs_num, 15);
|
|
if (ret != MV_OK) {
|
|
printf("ddr3_tip_bist_activate failed (0x%x)\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
ret = ddr3_tip_bist_read_result(dev_num, i, &st_bist_result);
|
|
if (ret != MV_OK) {
|
|
printf("ddr3_tip_bist_read_result failed\n");
|
|
return ret;
|
|
}
|
|
result[i] = st_bist_result.bist_error_cnt;
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Set BIST Operation
|
|
*/
|
|
|
|
static int ddr3_tip_bist_operation(u32 dev_num,
|
|
enum hws_access_type access_type,
|
|
u32 if_id, enum hws_bist_operation oper_type)
|
|
{
|
|
if (oper_type == BIST_STOP) {
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
ODPG_BIST_DONE, 1 << 8, 1 << 8));
|
|
} else {
|
|
CHECK_STATUS(ddr3_tip_if_write(dev_num, access_type, if_id,
|
|
ODPG_BIST_DONE, 1, 1));
|
|
}
|
|
|
|
return MV_OK;
|
|
}
|
|
|
|
/*
|
|
* Print BIST result
|
|
*/
|
|
void ddr3_tip_print_bist_res(void)
|
|
{
|
|
u32 dev_num = 0;
|
|
u32 i;
|
|
struct bist_result st_bist_result[MAX_INTERFACE_NUM];
|
|
int res;
|
|
struct hws_topology_map *tm = ddr3_get_topology_map();
|
|
|
|
for (i = 0; i < MAX_INTERFACE_NUM; i++) {
|
|
if (IS_ACTIVE(tm->if_act_mask, i) == 0)
|
|
continue;
|
|
|
|
res = ddr3_tip_bist_read_result(dev_num, i, &st_bist_result[i]);
|
|
if (res != MV_OK) {
|
|
DEBUG_TRAINING_BIST_ENGINE(
|
|
DEBUG_LEVEL_ERROR,
|
|
("ddr3_tip_bist_read_result failed\n"));
|
|
return;
|
|
}
|
|
}
|
|
|
|
DEBUG_TRAINING_BIST_ENGINE(
|
|
DEBUG_LEVEL_INFO,
|
|
("interface | error_cnt | fail_low | fail_high | fail_addr\n"));
|
|
|
|
for (i = 0; i < MAX_INTERFACE_NUM; i++) {
|
|
if (IS_ACTIVE(tm->if_act_mask, i) ==
|
|
0)
|
|
continue;
|
|
|
|
DEBUG_TRAINING_BIST_ENGINE(
|
|
DEBUG_LEVEL_INFO,
|
|
("%d | 0x%08x | 0x%08x | 0x%08x | 0x%08x\n",
|
|
i, st_bist_result[i].bist_error_cnt,
|
|
st_bist_result[i].bist_fail_low,
|
|
st_bist_result[i].bist_fail_high,
|
|
st_bist_result[i].bist_last_fail_addr));
|
|
}
|
|
}
|
|
|